Wont Reconize 2nd Cpu

The problem i am having when i try and set clock frequency to x11 for athlon fx51 it wont boot with 2 cpus. When i have single cpu in, it will boot at x11. Changed the 2nd cpu to cpu1 all by itself and boots fine, but when together i have problems. But when i leave it at x10 my system runs fine with 2 cpus. Second problem is during boot up the system only shows 1 cpu installed..Any one have any ideas why this is. System stats are as follow.
Msi k8t master Far2
Antec 550 watt server power supply with ssi
1.0 gig memory ecc..512 split into two different banks
nvidia fx 5200 256 meg card
120 serial ata seagate.
floppy
cdrw
xp with sp1a

Wow that Just shows you that I have Much to Learn about AMD System , As I am Browsing these AMD Forums Because I am in the Process of Building a Dual Opteron 248 Rig on a Tyan Thunder MB with Much Help from "Bas"..But I was under the Impression that the FX-51 Did not have any Dual CPU 940 Pin Boards in Order to support this CPU in Dual Configuration ....As I was Under the Impression that they Only Made Dual CPU boards to support the Opteron CPU's......Well you learn something new every minute in my Case ..............Sean REILLY875

Similar Messages

Brand new ipod nano 3rd gen wont reconize or charge!!

ok i received a 3rd gen nano as a gift brand new sealed. i have a new 80 classic so i just saved it in my desk. i turned it on to look at it and select language when i first got it but that was it. now it's been 3 months sitting, now i want to use it so i had my friend sync it to his itunes to get different music. ok it loaded all songs, charged up and worked fine now a week later went to charge it off my computer and it wont charge and itunes wont reconize it. wall charger wont charge it either. the computer reconizes it as a "usb mass storage device" pops up. took back to my friends and did the same thing. bottom line it wont charge or reconize on itunes. any help?
Message was edited by: BIG-J

Hi thesquib,
Have you tried connecting your iPod to your computer in Disk Mode? Sometimes if an iPod is in disk mode it will be recognized better by the computer.
For instructions, see this article:
Putting iPod into disk mode
Also, did you try all of these five steps?:
The Five Rs
-Kylene

New D20, Windows 7/Vista can't see hard drives - also 2nd CPU questions

I just got a new D20 and aded a few 1TB Samsung hard drives to the WD one that came with it. I can see the drives fine in both the Marvell BIOS RAID setup utility (even ran a Verify Disk on them with no errors) and from the ThinkStation BIOS and even from a Linux-based utility that I used to partition and format them with. But neither Windows 7 RC nor Vista x64 Ultimate can see any of the drives and when I try to load drivers fro the driver CD that came with it, they aren't recognized or loaded. Probably there is a simply BIOS setting I've screwed up but it has me stumped. Any clues?
Also the machine came with one dual-core E5502 CPU. If I want to add a 2nd CPU does it also have to be the same as the 1st or can I add a quad-core E5504 or even a higher speed quad-core as long as it is a LGA1366? Does it have to be a Xeon or would an i7 work?
Many thanks in advance!
ThinkStations: D10, D20, and S20
ThinkCentres: S50, M51, A61e
ThinkPads: W520, X60T and X61T SXGA+ tablets

welcome to the forum!
sounds like that D20 arrived in one piece.
the latest marvell driver for vista 64 can be found here. i suggest trying that first to make sure this isn't a driver issue. also check that you have the intel chipset and matrix storage drivers installed. they can be found here.
check the BIOS and see if the AHCI mode is set to SATA RAID. i can't remember the exact path to this setting right now but can reboot and write it down if you get lost.
on the processor, the second one does have to match the first unless you replace the first completely and install two new chips. an i7 might work as a single processor in socket 0 (this is untested so i cannot confirm). however, you'll need two xeons if you want to run two physical processors.
i suggest reading the following links for reference:
Hardware Maintenance Manual
Processor Instructions
Heat sink
Hardware Replacement Guide
ThinkStation C20
ThinkPad X1C · X220 · X60T · s30 · 600

Hi i recently bought an ipad from a friend and when i plugged it in to do the update it closed out and now it wont reconize it and my ipad tells me to plug it into itunes but it wont help me please idk what to do"

Hi i recently bought an ipad 1st gen from a friend i was playing it for awhie and decided to transfer my stuff onto it so i plugged into itunes did the update then it closed out and now my computer wont even reconize it and my ipad says to plug it into itunes like when you first buy them so i plugged it in but my computer wont reconize it and now i cant do anything on it

The way you download older apps for the older, original iPad 1, as I understand it, is if you have iTunes installed on a computer, you purchase / download the new, current app, in the iOS App Store in iTunes on your computer. Then, go back to your iPad and go to the App Store app on your iPad and find the same app there and download it.
When You select app to update/download, a message pop-up window appears asking if you want to download the last compatible version for your device (if one still exists ) tap OK and that should be it.

I recently had to have my computer fixed and now it wont reconize my ipod it wants me to erase to add more books to it is there a way around this i hate to reload all my music and books

i recently had to have my computer fixed and now it wont reconize my ipod. I do not want to have to reload all my music is there any way around this

Use your backup copy of your computer to put everything back.

My computer wont reconize my ipod in recovery mode.

my computer wont reconize my ipod in recovery mode. when i plug it it it doesnt even show up in itunes. what should i do?

Contact Apple.

It wont reconize it because ive never connected it to my i tunes. it belonged to a friend of the family and they gave it to her. she just got it and i havent had a chance to sync it to our iTunes account yet

it wont reconize it because ive never connected it to my i tunes.
it belonged to a friend of the family and they gave it to her. she just got it and i havent had a chance to sync it to our iTunes account yet

Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.

2nd CPU not recognized on Compaq Proliant 1500

I have x86/2.6 running on a dual CPU Compaq Proliant 1500, but it's not recognizing the 2nd CPU. (verified with mpstat)
Does anyone know how to convince x86 to initialize the 2nd CPU?
Thanks in advance!
David

Saw your post at http://forum.sun.com/profile.jsp?user=10948. I was having the exact same problem with the EXACT same hardware and I got the solution for you too. No charge! :-)
I contacted Compaq support and got a REAL sharpy on the phone. Compaq EISA config has an undocumented feature called 'Advanced'. To turn on the second CPU in Compaq ROM, follow these steps.
Start EISA config.
To use the 'Advanced' feature, merely hit 'CTRL-A' at the EISA config main menu.
Run configure system.
When it is done, go into Edit Details and scroll down until you see a line item called APIC.
It probably says DISABLED.
Highlight it and hit the ENTER key.
At that point, you'll see two options for 'ENABLE'.
Pick the one that says 'Full Table'. 'Full Table - Mapped' evidently don't mix with Solaris.
Save and exit, cycle power, and restart EISA config.
Save, exite, recycle power again.
At this next power up, the post message should say 'Processors Running at xxx' The next line should say Processor 2 initializing. When Solaris boots up, use the psrinfo command (no options) and it should show both processors up and running. psadm allows you to change the state of the other processor.
Let me know how this works. Mine is working like a champ!

Essbase crash after enabling a 2nd CPU

Hi,
We're testing a migration to virtual environments. Moving the tiers to VM worked without a glitch, however, enabling a 2nd CPU on VM causes Essbase to crash without a hint in the error log. Any ideas? Should I make any configuration changes after enabling the 2nd CPU? 11.1.2.1 on Windows.
Thanks,
Alin

Oracle does support HyperThreading, they just don't recommend it. Anyway, the VM system is on AMD CPUs so there's no hyperthreading involved.
Is there any relevant change in Essbase configuration if it's running on n>1 CPUs?

Why wont my 2nd generation ipod touch turn on anymore ?

why wont my 2nd generation ipod touch turn on ?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Computer wont reconize i pod wont charge 80 gb classic what can i do?

my computer wont reconize my ipod and said it is corrupted and it wont charge what sould i do ?

try the troubleshooting on apple

My laptop wont reconize my iphone 4s

My laptop wont reconize my iphone 4s but it will reconize my parteners 3gs help me

Do you mean Itunes doesn't see your iphone? if so take a look at the link
http://support.apple.com/kb/TS1538

HT1369 i hav a sony walkman.itune wont reconize it.what do i do?

itune wont reconize my walkman.mp3.what do i do?

iTunes is not designed to work with Sony Walkmans.
Consult the instructions for the Walkman to find out how to use it.

My ipod touch 2nd generation will not power on , charge, or wont reconize when i plug into computer.

Hi my ipod touch 2nd generation was working fine one night and the next morning it was off and would not power on and not charge and when i plug it into computer it is not reconized nor will it charge. I tried another ipod with the same cord and it works just fine. the battery has been holding charge just fine. i tried holding the sleep wake button and the home button and that or anything else ive tried it has been unresponsive. please give me some advice on what i should do! thank you so much! oh yeah i bought it may of last year.

Sounds like you battery may have went kaput. :(
Basic troubleshooting steps.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G + 120G OCZ Vertex 3 SSD Boot HD 

Task manager on windows server 2008 doesn't show the memory from newly installed 2nd CPU

Hi,
We have a dual processor dell power edge t410 running windows server 2008 (64-bit), standard edition. I have recently added a 2nd xeon x5560 quad-core processor (first one is also x5560 with 32GB (4x8) memory) and 16GB ram (4x4). Seems like the new CPU is
recognized in BIOS, Dell's server admin app and task manager shows 16 vertical boxes (hyper threading is on both cpus) under Performance->CPU Usage History and these boxes show processor load spread relatively evenly across all threads. On the other hand
the additional memory for this CPU is visible in the BIOS, Dell server admin but not in the task manager, which still shows the 32gb under performance->physical memory. Rammap also shows only 32GB.. Currently running proprietary processes that along with
the metafile and windows own ring up nearly 30GB, which in turn causes system latency for GUI and apps, as if the additional 16GB are not there...
So the questions are these:
1) does anybody know why the added memory doesn't show up in the task manager / rammap?
2) if the new memory doesn't show up, does this mean that Windows does not use it (which should be impossible if the CPU is utilized, unless I am wrong about windows using the cpu..)?
Thank you,
- Kiril

Thanks for the reply Ravikumar,
Unfortunately this solution is inapplicable to my version of the OS as it is 64-bit and not 32-bit. Do you have any other ideas?
Best,
- Kiril
Yes, PAE((Physical Address Extension) is supported only on 32-bit versions of the
Windows, operating system 64-bit versions of Windows do not support PAE. For information about device driver and system requirements for 64-bit versions of Windows, see
64-bit System Design. The Address Windowing Extension (AWE) API is supported on 32-bit systems. It is also supported on x64 systems for both native and Wow64 applications.
Useful link for Address Windowing Extensions is:http://msdn.microsoft.com/en-us/library/windows/desktop/aa366527(v=vs.85).aspx
If the above info does not help you, please contact dell as suggested by
Shaon Shan.
Regards, Ravikumar P

Wont Reconize 2nd Cpu

Similar Messages

Maybe you are looking for