Wont run in user mode

I can load and run adobe cs5.5 in windows 7 on our school domain, but when I log into the computer with a student account it says cannot run in guest account.
Adobe says I need to grant full admin rights, but this is impossible and does not make sense, I work at a College, the whole point of a College network is to restrict student access, adobe must realize a large part of their clients are in this same boat. I have never had a problem with xp and previous versions of cs.
Please help me?
Ian

Thanks,
just to clarify, think i need to grant the rights, re-install in admin mode, test in user mode, than go back to group policy rights?

Similar Messages

K7N2 Wont work in user mode

Hi, i just installed my K7Ns with an XP 2000+ and a Radeon 9500pro and 512mb(2 sticks, only reading as 128 each) of Infinion PC-2100 DDR. Now, when I set jumper 10 to user mode, my machine crashes, but when it is in Safe mode, my system runs fine. Does anybody know what is going on?

well, i messed around with J10 and 11, and messed around with the FSB in the BIOS, and it finally came back to life.

To mount a CD-ROM in Single User Mode. How?

Thank you for reading my question.
I need to run single user mode on my iMac because of a disk problem. I would like to be able to mount the cd drive while I am in single user mode. I would also like to be able to mount usb hard drives with confidence, so that I can copy off files from the internal hard drive.
I am in single user mode, which I get to by holding down Command-S on startup. I can look at the disks that are attached to my computer by executing
ls -l /dev/disk*
However this appears to be adding disks. I started with /dev/disk2 and /dev/disk2s1 etc which I understand are partitions on that external drive. Now when I list /dev/disk* I have /dev/disk3 and a couple of partitions on those devs. Is that normal? Have I not unmounted disks properly?
I have been using a directory that already exists as the mount point for my usb drives using
mount -t hfs /dev/disk1 /cores
which worked fine. Alas the disk I mounted on that directory was too small. Now I can't mount a disk on there. Do I need to unmount or fix up that assignment?
If I were to create a directory in /Volumes is that advisable? How do I make the root directory readable is that by using 'mount -uw'?
Thank you. Please if you answer my question, try to be clear on what commands to use and why. Bear in mind that other people will read this, and no one on the web seems able to write suggestions very clearly. Maybe we can be the first! If I have not been clear, please feel free to ask for clarification. i am not a total unix newbie. Rather in the 20 years since I was a sysadmin, my memory has faded.
Pete

I think you need to post this in a different forum. I think the Developer Forums would be the right choice.
In any event from the little Unix I know you can't mount a removable device until it's connected which means you need to put a CD/DVD into the optical drive. At that point if you enter 'df' you should see the device if it is mounted automatically (which I believe it does.)
In single-user mode the entire drive is readable and all files accessible. You are the 'root' user. In order to put the system into write mode you must enter 'mount -uw /'. Note the '/' at the end of the comnmand line. That makes the entire system writeable.
You do not need to create a directory in /Volumes. When the CD/DVD is recognized an entry in /Volumes will appear unless the disc is unformatted.
Now take some of the above with a grain of salt. I'm certainly no Unix expert.

User Mode Linux -- Compiling problem

Hi,
I want to run the user mode linux for linux-2.6.17.6. When I try to compile the user mode linux I get this error:
In file included from arch/um/include/os.h:13,
from arch/um/drivers/fd.c:14:
arch/um/include/kern_util.h:9:27: error: linux/threads.h: No such file or directory
make[1]: *** [arch/um/drivers/fd.o] Error 1
make: *** [arch/um/drivers] Error 2
I was looking up a lot of time in google.
My steps to compile it is:
export ARCH=um
make defconfig
make
If you have any suggestion, let me know.
Bye.

Using that option the kernel compiles smoothly. The problem here, is that I am not getting the kernel that I want. I am just building a normal kernel.
Any suggestion, let me know
Luis.

Hi i am having a big trouble. MY mac wont start past the gray screen. I tried starting on safe boot, single user user mode , recovery mode. Everything it gets stuck on the gray screen i even tried reinstalling it , same thing what should i do?

MY mac wont start past the gray screen. I tried starting on safe boot, single user user mode , recovery mode. Everything it gets stuck on the gray screen i even tried reinstalling it , same thing what should i do? it lets me reinstall sometimes Sometimes.... it is weird.

orshikhfromsc,
boot from the Mac OS X Install DVD that originally came in the box with your MacBook Pro (by holding down the C key as it starts up). When the desktop appears, select Disk Utility from the Utilities menu and erase your internal disk. After it’s been erased, reformat it. After it’s been reformatted, exit Disk Utility and reïnstall the version of Mac OS X from that DVD onto your internal disk. After that version of Mac OS X has been reïnstalled, boot from your internal disk and run Software Update to get it up-to-date within that version; that should allow you to redownload and reïnstall Mavericks, if desired. If Mavericks is reïnstalled, run Software Update again to get it up to date.
If you no longer have the two grey installation DVDs, you can purchase a replacement set from either Apple or iFixit.

Can I run DW4 in Safe/Single User mode?

I have downloaded DiskWarrior 4, biut I am unable to create a boot disc from the .dmg file. Is it possible to run the DW4 application from Safe Boot/Single User mode?

Once you get the physical CD in the mail, that one should boot your computer. Until then, you'll have to boot from a different drive.
I keep a copy of OS X installed on my iPod for troubleshooting purposes. It's got DiskWarrior, the AppleCare TechTool, Intech Speed Tools, etc. installed on it.

Can you run a bash script on boot in single user mode

Hey guys quick question.
Is it possible to run a bash script on boot in single user mode.
I can create a file and dump it on the root hd.
Let's call it repair.
I can then boot to single user mode and run it by typing /repair.
But I want it to do it automatically.
Every time I go into my machines that I clean for my job. I have to run sbin/fsck -fy
Then I have to mount the drive and then remove all cache files, then reboot the machines.
I would like to automate this by just holding command s and then moving to the next computer.
There must be some sort of boot daemon somewhere.
Please help.
Sincerely,
John

Have you seen Applejack?
http://applejack.sourceforge.net/
It doesn't start automtically, but does cleanup.
Robert

MBP only runs if I start in single user mode and run fsck. WHY!

I am having trouble with my MBP. If I don't start in single user mode and run fsck -fy twice, I can't click on anything with my trackpad. I can't even log in. I've tried resetting pram/nvram, disk permission repair too but once i reboot... nada. I can't do anything in recovery mode, I can move around with arrows and tab but can't select anything. Safe mode hangs at about 20% and doesn't budge (left it for an hour, nothing). If I run fsck -fy it works but as soon as I reboot/ logout i'm back to square one again. Anyone know what causes this to happen? It just started tonight. I have a 2012 15" with Mountain Lion.

The boot drive is failing, or you have some other hardware fault.
Back up all data immediately, then make a "Genius" appointment at an Apple Store to have the machine tested.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to bare metal from any of them.) Don’t erase the recovery partition, if present.
*An SSD doesn't need to be zeroed.

Latest Patch cluster (Feb 11, 2010) unable to run in Single user mode.

Hi ,
This is my first post in this forum.
Hope you people will help to resolve the issue.
My issue - I have downloaded the latest patch cluster (Feb 11, 20100) and tried to install it from single user mode.
Nothing happened. I have waited for more than 30 mins, still no progres.
Then I killed the process, and tried to run it in Multi user mode (To verify any issue with extraction or file) -- Its working(and killed the process) !!!
Anyone facing this strange issue ?
Appreciate your help to complete the patching.
Thanks.
sas.

Hi,
If you're encountering issues with a patch cluster bundle your best bet is to contact [email protected] From the description it sounds like there may be a filesystem not mounted in SUM that the cluster is trying to patch.

Extremely slow startup/"Error loading kernel" when single user mode is run

My daughter's iMac has become very poorly responsive with a very slow startup time. It takes about 1 minute for the progress wheel to begin when I startup her machine. And then it takes another 2 1/2 to 3 minutes before the login screen appears. The computer runs very slowly with the spinning activity wheel occurring frequently. When I start it up in single user mode I get the following message on screen:
efiboot loaded from device: Acp:(PNP0A03,0)/PC: (1F12)/SATA(0,0)/HD(Part 2, Sig56BF F8F1-9ADB-4101-BD3C-BFBC38AEED26)
boot file path: \System\Library\CoreServices\boot.efi
.Loading Kernal cache file 'System\Library\Caches
com.apple.kext.caches\Startup\kernel cache_i386.AE149BE8'
Read error 0x7
Loading 'Mach Kernel'...
Could not open file 'Mach kernel'
Error loading kernel 'Mach_kernel' (0x9)
Could some one tell me what this means? And better still, what do I need to do to fix it?
Thanks.
JOhn

I can't picture what is doing this other than something missing or muxed, but perhaps it's time for a relatively painless Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space and no Disk corruption, and is relatively quick & painless...
http://docs.info.apple.com/article.html?artnum=107120
Just be sure to select Preserve Users & Settings.

Mac not booting normally after running '/sbin/fsck -fy' in Single user mode

HI, I tried to log in to single user mode and run the '/sbin/fsck -fy' command. This command failed. So I rebooted my Macbook pro by 'reboot' command. On bootup I hear the chime shoud and can see the Mac Symbol but never reach the login prompt. The round circle keeps rotating over the gray screen and nothing happens.
Then I again hard rebooted mac book and entered single user mode. I ran again '/sbin/fsck -fy' many times and after many attempts the command stuck and never returned.
Then I tried using the recovery method to reinstall MAC OS X. It asked me to choose the Harddrive where to install MAC OSX. But the option of "macintosh HD" was disabled and message was " hard drive locked".
Please help me how to boot my MAC normally :'(

Welcome to the Apple Support Communities
Boot in Recovery again and open Disk Utility. Then, choose "Macintosh HD" in the sidebar and repair the hard drive. If it is repaired, restart and OS X should start correctly. If not, you will probably have to format the hard disk.
You only have to use that command when you have problems with the Mac OS X volume filesystem that they couldn't be repaired with Disk Utility, and as this command got stuck, probably damaged the OS X volume filesystem

Macbook shuts off during start-up - can't get through safe-mode, single user mode (fsck -fy) and target-drive shows no problems when running disk utility repair

Hi everyone,
I'm simply all out of ideas on what to do - my best guess is the problem is not specifically hard-drive related since all the 'normal' fixes just won't work.
What could be the cause of my issue? The only way i've managed to keep the Macbook Pro on for longer than a minute is through target drive, where it seems to work just fine - i can access everything. To sum up everything:
1 - I tried resetting the PRAM
2 - I tried to go in to safe mode, it shut off before i could type the password
3 - I tried fsck -fy command from single user mode, sometimes i can get to actually typing it but mostly it shuts off before
4 - I tried to repair disk via target drive - success, no problems detected (and it didnt fix my issue)
5 - I reinstalled OS Mavericks.
The Macbook Pro previously had some problems with the power-button not working properly (a mac-cunning friend of mine had to open up the mac and start it by swiping to metal pins on a specific (battery/power?) part inside it. The problem kinda went away afterwards but it might be related to this?
This is way off my comfort zone of 'diagnosing' issues, so I'm crossing fingers for some good advice.
Thanks,
Aske
Denmark

I think you're right.
If it's hardware related, is it possible to guess at what it might be? It would be nice to know how much I should expect to pay for a repair before actually getting it fixed.

Task Scheduler wont run when set to "Run whether user is logged on or not"

Hi
I have two 2008 R2 servers with the same task and pretty much the same powershell script the schedule is running. The powershell just runs a daily snapshot of the server. One server it runs fine with "Run whether user is logged on
or not" selected. But when selected on the second server it won't run. I mean, the schedule says its run, but the poweshell doesn't launch and do its job. Everything is the same on each server apart from what is being snapshotted.
Even the location of where the snapshot is going is the same. Same domain account, same password. When I change it to "Run only....." it runs fine. But the server may not be logged in all the time, so I need it to run whatever.
Any help would be greatly appreciated.
Thanks
Matt

I'd check in the windows system and application event logs. Also check the task log.
Event Viewer\Applications\Microsoft\Windows\TaskScheduler\Operational
Regards, Dave Patrick ....
Microsoft Certified Professional
Microsoft MVP [Windows]
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

Repair Permissions in Single User Mode

So, I have searched various posts and have yet to find anything that has worked so far. Hopefully, someone can still help. I recently made the mistake of changing my permissions on my hard drive. I clicked "Get Info" for the Boot volume and changed the permissions for "Everyone." I thought I had corrected it, but now when I try to boot, it just sits at the apple grey screen with the spinner and never loads the OS. Judging from other comments, this appears to be a permissions issue and all I need to do is repair the permissions which is why I ran through these commands in Single User mode:
/sbin/fsck -fy<return> --I did this twice to fix the drive
/sbin/fsck -fy<return>
/sbin/mount -uw<return>
/sbin/autodiskmount -va <return>
/usr/sbin/diskutil repairPermissions /<return>
sudo diskutil repairPermissions /
I am having to run through the Single User mode because I do not have the SL install disk. However, I have Windows installed on a Boot Camp partition and I can access files on the mac side but everything is read only.
I am a novice at the command line so any guidance on what commands might help to repair permissions would be great.

Found this for Leopard. Will probably work in 10.6
Run these commands and hit enter after each. Be careful with the spaces; keep exactly as written. There are various suggestions in this thread, which you might first want to check out, but this seems to be the most promising.
http://forums.macnn.com/90/mac-os-x/370223/changed-hd-permissions-mac-wont-get/
mount -uw /
chmod 775 /
chmod 1775 /
Then restart
BTW, not recommended to repair Permissions from the install disk, since if you've updated since installing, those will be out of date and incorrect. Permissions Repair should be done from the normal boot volume.
Message was edited by: WZZZ

Data back up from Single User Mode

Hello,
I have a problem with my 700 MHz iBook, dual USB, with OS X 10.3.9.
Unfortunately the OS doesn't start up because of "overlapped extent allocation" problem...
I would like to re-install the complete OS but before doing it, I would like to back up some directories.
Is it possible to save some data, by connecting an Ipod or some sort of external peripheral, from the Single User mode?
If yes, how can I do it?
Thank you in advance from your kind support.

Before giving up the ghost check out these:
http://docs.info.apple.com/article.html?artnum=25770.
Manually fix Overlapped Extent Allocation Errors without Disk Warrior
Overlapped overlapped extent allocation errors can be the bane of any Mac user's existence. Often, these errors go unnoticed until the problem becomes visible: your Mac might refuse to boot, crash unexpected, or worse, critical data might disappear from the Finder. Disk Utility can detect, but not fix overlapped extent allocation errors, and certain third-party utilities, such as Alsoft Diskwarrior, can fix them, but generally without reporting the consequences.
Overlapped extent allocation error occur when the file system thinks that two files are occupying the same area on the hard disk, hence overlapping on the same "inode," which is the structure which holds the location of the data blocks the file occupies, and also file permissions and flags.
Clearing the "overlapped" or "overallocated" extent allocation essentially means that you'll have to lose some data, because the only way to remove the overlap is to delete the file that's occupying the inode. So, if you suspect, or find out, that the guilty file is a critical system file that resides in one of the hidden system directories such as /etc /var /usr/ or visible system directories such as /System or /Library, and you don't want to reinstall the whole OS (which might not fix the overlapped extent allocation anyway), it's good to have another disk available to copy the files back to your original disk if necessary: a second bootable hard drive or a firewire drive connected to your Mac when you remove the misbehaving file. Just make sure that when you copy the file back to your boot disk that the permissions are correct, so it's best to use the "ditto" command, so that all sticky bits, flags, and permissions are preserved.
In case you didn't know, you don't have to boot from an install CD in order to check for overlapped extent allocations. All you need to do is restart your Mac, while holding down command + S to boot in "single-user mode."
At the command prompt that appears, type:
$ fsck -fy
If you have an overlapped extent allocation, you'll see:
"Overlapped Extent Allocation" (File 123456d)
No matter how many times you run fsck -fy, you'll never be rid of the error.
So, simply issue the following command:
find / -inum 123456 -print
Note the "d" was dropped, or any extra letter that appears after the inode number.
The find will return a file name that matches with the inode number, and the path to that file. If you remove the file then the fsck will not return this error next time you run it.
However, before you can delete the file(s) in single-user mode, you'll need to mount the file system. Type:
$ mount -uw /
When done, issue the "sync" command, and that will flush the write cache so that all pending writes are written from memory to the disk. Also, since most OS X 10.3 Macs use the HFS+ Journaled file system, it might be a good idea to disable the journal before booting into single-user mode by typing:
$ sudo diskutil disableJournal /
then re-enable it when done fixing the overlapped extents and rebooting normally:
$ sudo diskutil enableJournal /
Chris Anderson is a long-time Linux propellerhead who just got his first Mac, an ibook G4, and can't keep his hands off of it. He currently works as a "The Architect" and general visionary for a maker of world-class collectibles.
If you own Disk Warrior then it should be able to repair a drive with overlapped extents.
There are two backup utilities included in Unix - psync and rsync. You will find them in the /usr/bin/ directory. For documentation simply enter: man psync or man rsync. In order to write data while in single-user mode you need to issue the command: /sbin/mount/ -uw / (Note: there is a "space" between the "uw" and the "/".) To mount an external drive you will need to provide the mountpoint for it in place of the "/", e.g., "/Volumes/volname") without the quotes.

Wont run in user mode

Similar Messages

Maybe you are looking for