WORK AROUND: Black screen/flashing cursor trying to boot windows cd

This refers to the black screen with flashing underline cursor in the top left corner problem that happens after using bootcamp to setup your partition & then rebooting with the windows install CD in the driver. Install never starts, you just get this black screen with flashing cursor. seems to affect many different types of macs attempting to boot both XP & Vista.
I tried rebooting about 10 times. No luck. Same problem. Tried running disk verify/repair after removing partition, no luck. Remade boot camp partition, no luck.
Finally I pointed Parallels (free trial available) to my blank bootcamp partition and set parallels to boot from CD before HD. Parallels booted the Vista install CD just fine, and put Vista on my HD. Crashed at the end though and said it couldn't make the boot camp partition bootable so all changes were removed. Rebooted under boot camp and the installer came up fine off the CD. I'm now running vista (SP1 even) under bootcamp just fine. Parallels just lets you get past that boot-up bug.
So if you have this problem, and nobody else can help, and if you can find it, maybe you can download..... Parallels.
Feel free to post this on the other threads. Unlike other workarounds I'm guessing this will work for everyone and it only takes a free trial download of parallels to give it a try. Just remember to setup the virtual machine to use the bootcamp partition as the target drive, and then go under the edit virtual machine, then OPTIONS, then BOOT tab and set it to boot from cd before HD. Switch it back when you are done.
Then run boot camp assistant again and select the install OS option. Should run the installer correctly (thus overwriting anything parallels put on the partition).
I think VMWare Fusion also supports vitualization with the bootcamp partition as the target so that may help you get around this problem.

I have resolved this issue for four of our iMac computers with either of the following solutions. I realize that these solutions might seem awkward, but these solutions have been the only solutions that have successfully resolved this same issue for four different machines.
Solution 1
On the Mac OS partition, leave the Boot Camp partition that has yet to be configured.
Leave the Windows install disk in the optical drive.
Shut down the computer.
Unplug all cables.
Hold the power button for a minimum of 5 seconds.
Plug in all cables.
Turn the power on.
The computer will proceed to install Windows.
Solution 2 (If Solution 1 fails)
On the Mac OS partition, leave the Boot Camp partition that has yet to be configured.
Remove the Windows install disk from the optical drive.
Shut down the computer.
Unplug all cables.
Hold the power button for a minimum of 5 seconds.
Plug in all cables.
Turn the power on.
A black screen will appear prompting for a bootable disk.
Load the Windows install disk.
Shut down the computer by holding the power button.
Turn on the computer.
The computer will proceed to install Windows.

Similar Messages

Black Screen with Cursor (Tried most solutions)

To save your time and mine, I’ve tried all options in “press f8” and “recovery disk”. Over the past 3 days, I read almost all threads, videos, articles, and official MS help containing any mention of this problem. I also applied many commands, created few
“SystemRescue CDs” and “Kaspersky Rescue 10” on a usb drive. I follow instructions very well, and have never been stumped by a windows problem like this before. If someone solves this, you are a wizard!
Nothing has worked so far, but I really want to figure this out and not ‘reinstall’. It appears to be a simple and popular problem: “Right after Win 7 boot Logo, I get black screen with white mouse cursor,
no matter if I boot in safe mode, last good configuration, or normal startup”, but all the solutions that worked for most people are not working for me.
TL;DR: (answers to any of the 7 questions in the end will help me out)
Custom System: Win 7 64 bit (updated consistently), 4gb ram, Quad Core 2.66, 64GB SSD (Crucial M4) and 4 hard other drives. Only windows installations/updates have been installed onto the SSD, no other programs. Only 1 OS has ever been installed
on this computer. Never dual booted.
Mobo: Asus Maximus Formula. GPU: AMD HD7870LE
2014-04-19
I haven’t installed or downloaded any programs in the past 3 weeks, and did not notice anything unusual up until this incident.
In the morning the computer went into hibernation because I was away, it couldn’t wake up (usually happens), so I turned off the power supply. Turned it back on, and computer resumed, I was concerned as it may have run out of hard drive space on my 64GB
SSD (4GB free), but it booted fine.
Later during the day, I decided to restart the computer, and as it booted up again, it went into “start up repair”. I let it run and restart, and it arrived at the dreaded Black screen with mouse cursor, of death, right before logon screen.
Symptoms while on this black screen.
Ctrl alt del doesn’t work, power off doesn’t work, cursor can move, pressing ‘shift’ many times doesn’t bring up the ‘sticky key’. No task manager.
Hard drive is not loading anything, just idle.
Computer falls asleep after 15 minutes or so, and can wake up back to this black screen, so it remembers my power settings
Safe mode loads the drivers fine, but also gets stuck on the same ‘black screen with cursor’ forever
I tried every option in the ‘advanced boot’, including ‘safe with command prompt, safe with networking, last known configuration, etc’
Last known configuration, and all of the above, all boots to ‘black screen with cursor’, this means windows believed it booted fine the last time, so it remembered this configuration. That’s because all the drivers loaded without issue. While loading
Safe Mode, I can see windows loading all the drivers ok.
No restore or backups (I know, I do not deserve to live, lesson learned)
I tried all applicable functions from the ‘recovery cd command prompt’, bcdedit, bootrec, diskpart, and still couldn’t get it to boot.
Commands applied in Elevated Command Prompt from Installation DVD: (very careful with backups and overwriting)
Diskpart -> list volume, tells me that 100mb is system reserved, the other 59GB has no label, and is a different partition
Bootrec -> scanos, tells me that I have 0 windows installations, used fixboot, /fixmbr, /rebuildmbr, all successful. Mounting the drive later on RescueDisk’s TestDisk shows no problems with either partition.
BCDedit: shows both boot manager and winloader to be on the same drive, and I referenced it with a typical BCDedit enum output, and nothing is out of place.
I went into Regedit by typing “regedit” in command prompt in Win7 recovery cd, and confimed that ‘Shell=explorer.exe’ under:
HKEY_local machine/software/microsoft/WindowsNT/Currentversion/winlogon.
Sfc /scannow couldn’t run due to “Pending repairs/restart”
So I used: SFC.EXE /scannow /offbootdir=c:\ /offwindir=c:\windows
Which ran and repaired some errors the first time. I ran it more just to make sure, with restarts in between, it gave me
Win resource protection did not find any integrity violations.
So the system files appears to be fine and not corrupted.
Bootrec /scanos does not detect any windows installations. “0 Windows installations identified”, yet “Diskpart -> Detail Disk” and bcdedit both detects the windows directory.
From windows recovery disk:
Startup Repair diagnosis: (Show Details)
All tests completed successfully
Boot status indicates that the OS booted successfully
It seems that the system and the OS boots successfully, and windows believes it boots successfully (that’s why last know good configuration gives me the black screen also, and Win Startup Diagnosis all says it booted successfully”
It’s the second before it enters into the logon screen, the black screen and movable cursor appears, and hangs here forever. What programs load during this step, and how can I find out this info? Is there a diagnosis tool that allows me to see the programs
as they load during windows start up?
Other attempts:
Then I read it could be windows using “winresume.exe” instead of winloader.exe, since I have “hiberfil.sys” in C:\windows, so I backed it up and deleted it using SystemRescue.
Another thread said “winevt” bad logs, in C:\windows\system32\winevt were causing this black screen, so I backed it up and deleted that also, and it still won’t boot.
I plugged in the devices that were attached (just 1 ext hard drive, through a 10 port usb hub) that was connected while it went into hibernation on April 19th, and it didn’t help.
The files on that disk and the file system is not corrupt; I tested it by taking it out and docking it on a usb Blax Duet, and my laptop did a scan disc, and it’s fine. The Sfc Scan also shows that it is ok.
I also unplugged all the other sata drives, switched the SSD sata cable around to other sata ports to no prevail.
So far I know:
Very unlikely that it’s a virus problem, I haven’t installed or downloaded anything this month, scans from Kaspersky 10 rescue disk shows nothing, Farbar scan shows nothing. I also never install anything suspicious, like toolbars or junk. I scan regularily.
Not a driver problem, since I haven’t changed or updated anything. I unplugged all devices, and starting in 640x480 mode also gives the black screen with cursor. Drivers all loaded fine while starting windows and safe mode
Boot files are intact, windows system files are in the right place since windows actually boots into a shell? Both bootloader and boot manager show up in bcdedit enum scans
Not due to system file corruption, since file integrity are confirmed ok by above CMD commands, and windows diagnostic tool, and testdisk.
My questions:
What could be the cause of this? I didn’t make any changes to BIOS, windows settings, perform any updates, suspicious activities, installations, or crashes, before this. The files on that disk and the file system are not corrupt either, I tested it by
taking it out and docking it on a usb Blax Duet, and my laptop did a scan disc, and it’s fine.
Which program (classpnp.sys? explorer.exe? winlogon.exe?) is being loaded right before “windows logon screen” that would cause it to hang with a black background and cursor?
How can I find out this information? Is there a tool that can record all programs that are being loaded by windows at boot?
I only have access to regedit, elevated command prompt, and I can change files through SystemRescue or Kaspersky recue, how can I get the computer to boot past that black screen with a mouse cursor? The answer seems so close.
From the Rescue Disks, what could I really do to get past the black screen?
Those who are computer technicians could tell me: If I take it to a computer shop or technician, what could they do in a situation like this aside from all of the above? Do they have some ‘next level’ access tools or are they just going to waste my time
and tell me I have to reinstall?
At the very worst, I will obviously reintall. On my 64gb SSD, I didn’t install any important softwares. All my important software installations are on a separate drive. However, will they still work if I did a ‘Inplace Upgrade’ install of windows? Does
registry get wiped?

Hi,
Have you tried to take startup repair when booting with the rescue disk?
Startup Repair
And we'd better bring the PC to the vendors, then take an examination of the hardware health.
How does the Bootrec /scanos show 0 installation identified? We may take a try with chkdsk from command line to check if there are any disk errors:
Run Check Disk from a Command Line to Check for and fix Disk Errors
Please also take a check if the system reserved partition is stay in health:
Understand (and Get Rid of) the Mysterious Small Partition
Another shoot, please try to rebuild BCD:
Use Bootrec.exe in the Windows RE to troubleshoot startup issues
Regarding the repair install, detailed information please take a check with the article below:
How to do a repair install to fix Windows 7
Hope this may help
Best regards
Michael Shao
TechNet Community Support
Did you read his post at all as it does not look like it.
As to take it to a vendor "Custom System:"" Win 7 64 bit (updated consistently), 4gb ram, Quad Core 2.66, 64GB SSD (Crucial M4) and 4 hard other drives. Only windows installations/updates have been installed onto the SSD,
no other programs. Only 1 OS has ever been installed on this computer. Never dual booted."
As to your other suggestions he has tried them all as have thousands of us out here , all you have to do is search the internet and you see millions of hits about this.
And glad to see a moderator can mark a non answer as an answer.

Satellite Pro L300 - Black screen flashing cursor

Hi all,
I have a Toshiba Satellite Pro L300 laptop running Vista.
The client brought it in because when it boots it goes to Toshiba splash screen then goes to black screen with flashing cursor in left top corner. I have connected external monitor with same result. Swapped out RAM as well.
Have run Memtest (passed), Seagate HDD long test (passed), Ultimate boot CD, and Winternals with no success.
*F8 does not work* and nor does Factory recovery.
Can get into BIOS F2 and F12 no problem and the HDD is listed there.
I reinstalled Vista from CD and when rebooted it goes back to flashing cursor. I have attempted Startup repair from Vista CD and System restore. FixBoot from Command Prompt and FixMbr as well with the same result.
I have a feeling it may be a corrupted CMOS? It is like the OS installs properly, but the computer loses it's memory on reboot of where the OS is located?
Is the CMOS battery easily accessible and removable on this model?
Has anyone encountered these symptoms? Is it fixable cheaply?

Hello
If you have clients I presume you are some technician and hope you have some hardware parts in your store.
Have you tried to set BIOS to default settings and check it again?
If possible try to exchange HDD and test the functionality again.
Can you use notebook with Linux live CD (HDD not needed)?
To be honest I dont think problem is BIOS and, in my opinion, CMOS battery exchange is not necessary.
Test it please with new HDD and post some feedback.

Immensly long black screen with white underscore while booting Windows 7.

I've heard of some people having the same problem, I also looked through this forum, but the the solution I found here didn't work for me.
I can't run the command sfc/scannow in command promt because it says i must have administrator priveleges and enter a console session.
Any advice on how to enter it, or solve this problem would be more then welcome!

You always need to run CMD.exe as Administrator.
Try holding down control + click when you select it.
Also, boot from Windows 7 DVD and choose system repair.
If it started after some point in time, installed something, try the last restore check point.
Have you ever scheduled a disk check? Properties for your C: boot drive - hardware is always good to do once.

Installing Win 7 via Bootcamp on 27' iMac 2010 gives BLACK screen, BLINKING cursor error (BSBCE)?

Hi All,
All coments appreciated regarding thiis issue.
I have a 2010 27' i7 2.93Ghz iMac with 8Gb ram, 2Tb Seagate, and 256 Samsung SSD.
I am running 10.6.8 with all updates on the 2Tb Seagate (has BC 3.04), and 10.7.1 on the Samsung (has BC 4.0).
I have tried over a dozen times to install Win 7 (both a 32 bit Professional edition and a 64 bit Ultimate edition) on BC partitions on both drives. These have been all on separate occasions of course.
All installs result in what appears to be a successful install, but when the machine reboots to launch Win 7 for the first time, I ALWAYS get a black screen with a blinking cursor error (BSBCE).
This is not the 2009 video card driver issue problem reported so widely and referred to in the Apple article TS3173. I had that model previously and the way around that was to connect a second monitor/LCD for the installation.
No this is a new and separate issue.
And I am no nubie. I have used IT for over 25 years and teach networking courses in the Win and Mac environments.
The problem appears to be in a corrupt boot loader install.
I have used both WIn 7 install disks to do a repair each time. The repair says it is successful but after rebooting all I get is the black screen and flashing cursor, with no keyboard response. I have used both Bluetooth keyboards and USB keyboards. Nothing seems to make a difference re getting WIn 7 to boot after the install on either drive.
I have also used the Bootrec commands in the command window. They all return a successful outcome but when rebooting I see the ever familar BSBCE.
Now,,,,,here is the real puzzle. I copied my previous Win 7 Ultimate install using Winclone before I sold my older 27' iMac.
If I restore that install to the 2010 iMac Win 7 boots fine!
So some error is happening on my current machine when the bootloader/bootmanager is being written to the BC partition.
The problem is there with the BC on both 10.6 and 10.7, and these are different versions of BC!
Now to further complicate the problem, I manage 12X 2011 21.5' iMacs in a lab at work. Win 7 Professional 32bit installed on these machines just as it should (same disks that produces the black screen flashing cursor).
I have read that some people thing it is a Boot Rom version issue, and there may be some substance to this as WIN 7 installs so easily on the 2011 iMacs in my lab.
I called Applecare about this and went through the procedures outlined above. The guy was very helpful and sympathetic but he had no answer to the problem. His suggestion was to pull the SSD out and do it again with only one drive. As the machine can ship from Apple with both of these drives I really do doubt that pulling the SSD would make a difference.
Mac OS 10.6 and 10.7 work fine, no problems on both drives, so I don't think it is a drive issue.
OK Mac gurus...over to you.

I have a bookmark for iMac w/ SSD and hard drive.
There is also the 'req'd reading' in http://www.apple.com/support/bootcamp
with one article on Black screen w/ iMac 2010.

Iphone 4s is working for example can play,music recieve texts ,calls ect but has black screen and have tried the force shutdown method but still can see what im doing on the screen

iphone 4s is working for example can play,music recieve texts ,calls ect but has black screen and have tried the force shutdown method but still can see what im doing on the screen

Did anything happen to prior to your phone acting this way? It sounds like your screen is dead, but it is hard to say without knowing what what the cause.
1) was this a gradual problem? Did the phone screen start dimming a couple months ago and now has degraded or after some event (known or unknown to you), the phone started behaving this way.
2) Can you give more specifics on the problem? You said you have a black screen, but also you can see what you're doing on screen. Is the screen just really dim? Is the screen completely black? Does anything else besides attempting to reset the device cause it to flash white?

Trying to reformat and reinstall windows but get black screen with cursor

Im trying to reformat my computer after a blue screen error and when i pop in my disk to reformat and install it goes through the first stuff...opening files then it says starting windows and then black screen with cursor..nothing else..i can move the
cursor but i cant click anything..nothing happens.

Hi Marrik,
Is there any error code or error message displayed in the installation process ? because just based on your description in the post, it is difficult to find the root cause for a black screen even after a clean install, this might be caused by a corrupt installation
media or a hardware issue, so, I give two potential suggestion:
1.Try another Windows installation media and perform a clean install again to see the result.
2.Go to the computer vendor for hardware support, this also can be caused by a memory or hard disk issue.
Regards
Wade Liu
TechNet Community Support

MSI GT683R Black screen, blinking cursor

Hello, I was poking around for a similar topic but couldn't find one, so here I am.
Mine is an MSI GT683 laptop; it’s about four months old and second hand. When I boot it up, I see the MSI screen, and then I see a black screen with a blinking underscore cursor.
I’m pretty sure this is my fault, because when it arrived I decided I wasn’t satisfied with how it was setup (plus it had lots of stuff left over from the previous owner) and I reformatted and reinstalled Windows 7 on it. It booted up great the last time I used it; I installed all the updates, installed all the drivers, restarted it a couple times, and it was working like a charm. I even put a couple games on it. Then I put it into hibernation and left it alone for a day, and now I have the blinking black screen cursor of evil.
This is what I’ve tried so far:
1) I can’t get into the BIOS. When I restart, it doesn’t say “Press such and such to get into the BIOS!”, and nothing I press works (I thought MSI used Del, but in a fit of maadfobdogbd I also tried lots of other keys.) For that matter, I also can’t get into safe mode.
2) As far as I know there’s nothing wrong with the keyboard. I can actually adjust screen brightness with it. There’s nothing connected to the computer.
3) The Windows OS CD doesn’t work. It seems to think about using it, and whirrs around with it for a bit, but I never get anywhere other than black screen, blinking cursor. I’ve tried both Windows 7 and Windows XP, but nope.
4) I think my Windows 7 version may be x86. However, since it was running smoothly enough, I don't really think it was an issue.
Sorry for the trouble; hope you can help!

Boot disks don't work, either. Actually, this thread here shows my exact problem, and the answer sounds pretty plausible, given how I put the laptop into hibernation. Unfortunately, that guy never got it fixed. :<
https://forum-en.msi.com/index.php?topic=149961.0
I haven't gone so far as to take it apart yet. (I'm kinda leery of taking laptops apart. The last time I did it, I had to get stuff into this really awkward little space where I had no finger strength, and in the end I had to call a boy to snap the thing in for me. It was embarrassing.) I'm going to try swapping in another hard drive with Windows on it. I'll let you know how it goes.
EDIT: Alright! So it worked! Well, kinda. I got into the BIOS but it looks like my installation might be dead. I don't care a lot about the installation anyway, so while I'm going to try to fix it I may just reinstall everything... again.
I couldn’t get into the BIOS because it was apparently switched off for hibernation. What I did was that I dug up my giant box of computer parts and found an old hard drive that had Windows installed on it. I'm told that I should have swapped hard drives out (and I probably would have eventually), but just using a USB port worked for me. My laptop wouldn’t boot from a USB boot disk or from a CD, but it did find and boot from another hard drive, so I finally managed to shut it down properly.
I’m still getting black screen of blinking cursor evil, but this is progress. Still looking out for help.
EDIT EDIT: Useful links:
http://forums.lenovo.com/t5/Lenovo-3000-and-Essential/can-t-access-Bios-on-G560-anymore/td-p/445721
http://tips4pc.com/computer-problems/my-computer-boots-up-to-a-black-screen-with-a-flashing-cursor.htm

Black screen white cursor hell

The computer is a Sony Viao VGC-R210G running Windows XP Media with 4 GB RAM and an NVIDIA G8500 with a Matrox card.
On running Premiere Pro CS4, the program will appear to be running normally, then crashes and provides an error window. The OS then reboots itself. The Windows splash screen comes up and everything appears to be ready to boot, but all that is displayed is a black screen with a white moveable cursor. There is no way to get back to normal Windows operation after this, short of reloading the OS.
Believe me, I've tried.
This has happened twice -- huge pain in the *** reloading my drives.
Pardon me for being such a n00b, but if one is uploading an Adobe update of a Creative Suite, is it advisable to delete the original Adobe suite apps after the upgrade? It's just an intuitive guess, but I feel as though the two versions of Premiere are not playing nicely together. (I'm not launching them at the same time, but are they sharing resources that are different versions with the same name?)

Bill Gehrke wrote:
Could this be another case of Matrox card problems? Did you update at least to the latest Matrox drivers?
Thanks for the hint, Bill.
No. The last update of the Matrox drivers was 2007 when I got the card. Perhaps I should scan the forums for Matrox horror stories to see if these might apply.
I tend to doubt it though. On the last upload, Matrox wouldn't allow me to load the drivers until I had loaded Premiere Pro. I never got around to it before the black screen brought everything to a screeching halt.
On my Google quest to avoid reloading my drive, I found this black screen white cursor problem seems to be common, but the causes and solutions seem to be all different. Microsoft doesn't have any technical articles on it at all. The common element in my case was, unambiguously, use of Premiere Pro CS4.

When Mac reboots to Install XP black Screen Flashing Dash (-) stuck.

when Mac reboots to Install XP black Screen Flashing Dash and I think its the press any key screen but on a Mac its Just Flashing Dash .
I press every button going and nothing happens.
and my only option is to turn off the mac to boot back in OSX.
MacBook trying to Install Windows XPSP3 disk.

I too am having the same problem. I do not know about the host of this thread, but I have been using a brick and mortar version of XP SP2 stand alone so it is not bundled with a computer like Dell, HP, etc.
I have run it before just fine but it was time to reformat the drive, 0'd everything out, reinstalled 10.5.2, upgraded everything, repaired permissions and them ran Boot Camp. Put in the XP disc and all I get is the flashing dash mark in the upper left hand corner. I actually have 2 legal versions of XP SP2 stand alone and the same result on both discs so it has to be something with the partioning? I also redid the partitioning at various sizes all with the same effect. No luck.
Any new thoughts anyone?

IPhone 4s on screened Window Sill on rainy night - BLACK SCREEN, FLASH ON, VIBRATING, how do I revive?

Lastnight I left my Iphone 4s CHARGING on a screened window sill.
I wokeup at 8:30 and checked my phone to see that it was completely fine; went back to sleep until 10:30 and woke up to a black screen, flash on, and the phone frequently and randomly vibrating.The phone was not overly drenched. Only a couple raindrops on it, and around it.
I immediately stuck it in a bag of rice.
I need solutions! Any help is appreciated!
How long should I keep it in the bag of rice?
Is there a way to turn off my phone with a black screen?
Thank you for your help!

Just wind it by dryer and then don't try to switch it off because any electrical interchange cause damage. and then put it in a rise bucket. and in few hours it shuld be fine.. or take it to apple store if you are still in Warranty...

My iphone5 screen flashes when trying to make a call. I can't access any of screen features.

My screen flashes when trying to make an outgoing call. I am unable to access any of the screen features such as keyboard etc.

Could be a problem with the proximity sensor. Are you using a case around your phone or a protective film attached to the screen? If yes, remove them, to make sure that the sensor is not covered.
Also try to reset the phone by holding the sleep and home button for about 10sec, until the Apple logo comes back again. You will not lose data by resetting.

My Time Capsule backups disappeared (blank black screens) and in trying to set it up again I now find that when TC is plugged in and on (green light) it cancels out wifi reception from my router. I am only using TC as a backup not for wifi. Help!

My Time Capsule backups disappeared (blank black screens) and in trying to set it up again I now find that when TC is plugged in and on (green light) it cancels out wifi reception from my router. I am only using TC as a backup not for wifi. Can anybody help?

Sorry, you have lost me since it appears that you have two completely separate issues here.
All that I can suggest is you start over and try to set up the Time Capsule again first...and then, once that is done and the Time Capsule is working correctly on the network....then, try to troubleshoot the separate Time Machine issue.
If you decide that you want to do this, we'll need some basic information:
Make and model number of your modem?
You are using OS X Mavericks (10.9.3), correct?

Black Screen with cursor. Java Desktop System.

Hello everyone.
I've installed Solaris 10 05/08 x86 32bit in VMWare Workstation 6.5.
After I logged in in the system (Java Desktop System, Release 3), I've got only a black screen with cursor, nothing more.
X server: Xsun server configuration:
Video Device: VMWare Inc vmware0405
Video Driver: XF86 VMWARE
Resolution/Colors: 800x600 65536 colors @75Hz
Screen size: 17 inch
Monitor type: MultiFrequency 56Hz (up to 1280x1024 interlaced)
But the CDE starts normally.
What's the problem?
Help, please.
P.S. Computer with VMWARE Workstation: Asus P4P800SE, P4HT 3.0Gz, 2.0Gb Ram, Ati AIW X800 AGP 256Mb..
Edited by: xaxaTyH on Oct 9, 2008 7:26 AM
Edited by: xaxaTyH on Oct 9, 2008 7:45 AM

Hi
Have you installed all the Recommended Patchset . If not try to install the patches .
Regards

Black screen with cursor blinking for a long time before loading windows 7

Hey guys, i'm having an annoying problem with my macbook pro... i installed windows 7 using bootcamp and now i get a black screen with cursor blinking for a long time before loading windows... it *****, it takes about 3 minutes to get my notebook running
The first time i installed windows seven i did not have this problem... i already deleted the partition several times and installed windows again, but the black screen problem is still happening. i don't know what do
You guys have any tips? anyone with the same problem?? this ***** a lot. thanks

Hey Theoos..
Yeah, my version is not.. the first time i installed it was ok, but after 30 days it was asking for a key... then i installed a cracked version, and the cursor started blinking on start up, and took like 2 minutes...
I tested several cracks but with all of them happened the same.
Thanks

WORK AROUND: Black screen/flashing cursor trying to boot windows cd

Similar Messages

Maybe you are looking for