Work Center CR02

Hi,
We have created Work Center in 2007 with the following Validity date Jan 2007 to Dec 2009. I have checked the Validity date of associated Cost Center and its ending Year is 9999.
Now I want to Change the Validity date of Work Center to 9999. So this validity restriction could occur some issues during planned order creation or production order creation? Can I change the date directly.
Regards.....

Hi
this link will help you
[Work Centers - changing validity period under costing tab;
Regards

Similar Messages

Could not found any usage key in the work center WC001(Use T-CODE CR02)?

my question:
(1) I have created one Work Center WC001 and one Plant HJW1.
(2) I have created one Routing with T-CODE CA01.
(3) Then I use T-CODE CA02 to change this Routing.
(4) When I enter the Head details screen,I click the Operations button to enter the Operations Overview screen.
(5) In the Operations Overview screen list,I input the Work Center WC001 and the Plant HJW1 at the first line and press enter.Then the sap raise error message like below.
(6) The question was: I could not found any usage key in the work center WC001(Use T-CODE CR02)! Could any one tell me the answer or give me some advice to resolve the problem?Thank you so much.
error message:
Work center WC001 plant HJW1 does not exist for task list type N
Message no. CR084
Diagnosis
You want to allocate the work center WC001 to a task list of the type N . However this work center is not intended to be used in a task list of the type N.
Procedure
The usage of a work center in task lists is restricted via the usage key. You define this key in work center customizing and allocate to it those task list types in which a work center with this usage key can be used.
Proceed as follows:
Check the usage key for the work center WC001 in work center maintenance.
If necessary change the usage key in the work center or change the allocation of task list types to the usage key in customizing or
allocate to the task list a work center which is valid for use in a task list of the type N.

Hi
1) Check what task list usage key you entered for the work center in the basic data . If it is 009 then the work center can be used in all task list type.
2) If you have defined and used any other usage key , ensure that for this key , the routing type N is allowed in OP45.
Regards,
Ramasamy

How can I create a new work center

I try to create a new work center.I found a transaction 'OP42' . But I can't set a personal number and name.where should I write them, or should I use any other transaction??
Thanks...

Hi,
Pl go to <b>CR02 -Capacity-Goto menubar select Goto -Individual capacity -Enter personal name here</b>.
Hope this helps.
Regards,
Mani

URGENT........ACTIVITY TYPE AND THEIR ASSIGNEMENT TO WORK CENTER!!!!!!!!!!!

Hi Friends,
I have A REAL URGENT REQUIREMENT as far as activity type and assignment to Work Center is concerned.
I work for a client who is a manufacturer of Paint equipment. I'm responsible for capturing the cost of an assembly activity of spray guns, which is the last step of routing. However, there are 4 processes/steps of routing which are outsourced to the subcontracting vendors. we recieve the facbricated, anodised guns which are assembled in our factory.
I need to get the cost of assembly, which I have created as an actvity type in KL01 and planned for the same using KP26. However the system is throwing up errors related to costing, and I'm not sure about the assignment areas in work center.
And above all I'm not sure of various fields in KP26 like capacity field and what do we assign.
can anybody help me with the series of steps for me to be able to pick up the cost. or if there is any sort of material in this regards, plz mail it to: __ email removed by moderator
regards
sandhya

Hi,
You need to do the following:
1) Create an Activity type for the Assembly activity.
2) Define a Work Centre in PP (T-Code CR01) which represents the location where the Assembly is carried out.
3) Define a Cost Centre corresponding to the above Work Centre.
4) Plan for the Activity quantity for the combination of the Cost Centre and Activity type (KP26)
5) Plan for the Overhead Costs which are incurred on this Cost Centre which need to be included in the Standard cost of the Assembly.(KP06)
6) Assign the Cost centre & Acivity type to the Work Centre in CR02.(This is possible only after you do 5 above)
7) Execute the Plan price calculation (T-code KSPI)
After you do all of the above, when you do the Costing Run, all the relevant costs will be picked.
Ofcourse all the relevant master data for PP like BOM, Routing with the relevant assignments of materials to operations, etc should be in place.
Regards,
Assign points if useful

Bapi for change work center data

HIi All
I need BAPI to change work center data for all categories and work center change transactions .....IR02 ,CNR2,CR02.
Thanks in advance .

Hai,
Try the fm CRAP_WORKCENTER_CREATE
BAPI_BUS2054_CHANGE_MULTI
CRAP_WORKCENTER_CREATE
Regards,
Venkat

Regarding work center configuration.

Hi PP Gurus,
We need to take an account to Rated Line Speed (Bottles per minute) (i.e. It should be the current capacity of the bottling line operating at the full rated speed, irrespective of the bottling format).
We're using Discrete Manufacturing scenario and work center (CR01). How could it be taken into account.
Is there any alternte way to put an additional fiueld in work center create (CR01)/work center change (CR02) transaction code?
Thanks & Regards,
Abu Arbab
Edited by: abu arbaba on Jan 30, 2009 9:46 AM

hi,
What I mentioned is , create a reference operation set of one operation with that particular work center and maintain operation times as the speed of that line ( 100 bottles for minute should be entered as base qty as 100 and time as 1 min). Call this reference operation set in any routings that uses this line.
If you do this, you don't need additional field in work center and so don't get confused with it.
cheers
Rav

Activity cost at work center

Dear Exports,
I have a requirement in my project
1. In a work center we have 3 activities. 1. Labour time
                                                                   2. Machine Time
                                                                    3. No. Kgs treated.
I am able to give labour & Machine reates by giving price at kp26. and number of minitus in routing.
But my client wants machine hour rate : no. labours worked X Time worked X rate per hour .
i.e he wanted to give time in labour time activity and no of employees worked in machine time the formula must claculate
Labour time X Machine time(No of Workers worked) X KP26 Price(Per Labour hour).
Can Any body help me please...
Rao

Check if there is an existing WC formula that you can use or create your own formula for the work center.
My challenge (at a different business, so I don't have the exact work in front of me, but I have notes) was Crew size x Machine Hours x Activity rate.
In the routing Operation Details is a section General Data.
There is a field: Number of Employees, field name ANZMA, That is where we populated Crew size
Use an existing formula if possible
Which formula do I use??
    Work Center Basic Data (CR02) determine standard value key
    Go to "Define Standard Value Key" in IMG (OP19); select std value key and click detail button
     Note the Parameter used                                        IMG path: Production>Basic Data>WorkCenter>General Data>Standard Value >Define Standard Value Key
    Go to "Define formulas for work centers" in IMG (OP54); select formula that uses the field parameters required          IMG path: Production>Basic Data>WorkCenter>Capacity Planning>Work Center Formulas>
                     Define formulas for work centers
Not there? Create the formula
     In English - what do you want to calculate?
     Find parameters for the fields in the calculation
     Write formula (op54) Copy from existing formula if possible - spaces in the equation are necessary
                         OP17 is where to create new Parameters.
This is all configuration - with some high leve security (in our system). Configur and TEST CAREFULLY

User Exit or DB-Table for Work Center (CR01)

Hi!
I have an external software which must be triggered when the user changes a work center in SAP (transaction CR01,CR02). I was looking for an user exit to do what ever is necessary but I couldn't find one.
So, does anybody know an user exit or BADI for work center?
Also possible:
The database table where work center are stored. So I could poll against this table and check if a work center was changed. I found the table SGOSHIST which log all modified objects in SAP. So this could maybe used to check for modified work center, I think.
Thanks,
Konrad

> You can check the BADI definition from transaction SE18,
> 'LTRM_WORK_CNTR_DTRM', this might be helpful,
How can I check this BADI. If I use SE18, it doas not exist, buit if I try to create it, the system tells me that it already exists in the SAP Original System... and asks me if I want to create a copy of it! I don't know what to do at this point!
> Work center details are avilable in CRHD table, you can
> look for CR* from SE11 transaction,
I know, but if you change the description of the work center, it is stored in CRTX. there are a lot of CR* tables. It would be helpful to have a table which is updated every time a work center is modified!
Thanks,
Konrad

How to manage work center in Production order

Hi,
I am producing a material having one operation (suppose cutting), which I have mentioned in the routing. I have also mentioned the work center in routing on which cutting operation will be performed. When I make the Production order of 1000 pcs there comes only one work center. But practically, they are producing these 1000 pcs on two different work centers ( 500 on one and 500 on second). How to manage this in SAP.
Kindly help me.
Thanks and Regards,
Yogesh Singla

Dear ,
What is the individual capacacity of the Work Centre -CR02-Header -No of Individual Capacity ?
I think you must be using similar kind of work centre of 2 no 1000 pc .Now , when you are creating routing for this , you should hit Required Spilliting in Routing Operation -Select Operation line item and then Double click -Select Spilitting and enter splitting No 2.
At the same time in CR02-Work Center -Capacity Tab -Hit the Header -In the Bottom of the Detail Capacity Header -Avaialabile Capacity -Include 2 as Number of Inidvidaul Capacity and SAVE.
Now based on thr required spilittinga and invidual caapcity , it will consider the Work Centre Load .
Other wise , you can enter one more operation line in routing with similar Labor hrs , work center and control key in routung for production of 1000 pc .
Hope it clarifies
Regards
JH

Work Center in Project System

Hi Experts,
As per our requirement,
We need to send a workflow task to the users in that particular activity's work center after activity confirmation.
We have an internal Activity been created with some workcenter value for some plant.
But we are not getting that workcenter value in Organization Structure while setting recepient for the *Email Task in Workflow.
Is there any link between plant's workcenter(Project System) and Org Structure Workcenter(PPOCE) ??
And if its not same, then how can we link them?
Please help!
Thanks,
Runal

Hi Runal,
The workcenter used by project system is the logistical workcenter, (T-code CR01, CR02). The project system application does not care 'The Org Structure Workcenter(PPOCE) ' at all.
As far as I known, it is possible to maintain the link between the logistical workcenter with HR, if you start the CR02 and use button 'HR' assignement. Hope, you can link both workcenter this way.
Typically usage I known is the link in Capacities with HR, which the assigned person is used by project system workforce planning.
Kind regards,
Zhenbo

Pooled capacity, machine work center can have labour?

Dear All,
1) We have eg. a common pool of welders for Location A and Location B welding work centers. How do we setup the pooled capacity and assign to them?
2) We have eg. 2 CNC machining work centers (Vert and Horiz) but we have labour support to do machine setup, labour related jobs etc. If we need to perform labour capacity planning in this machine-based work center, is this done by maintaining a separate work center for this labour support and assigned to the same Cost Center? Or for machine-based work center, labour capacity planning is not required?
Thank you for contributing.

Dear
We have eg. a common pool of welders for Location A and Location B welding work centers. How do we setup the pooled capacity and assign to them?
There is no differnce between pooled capacity and available caapcity .Only thing is you can utilised this capacity pool for various work centre level.
To do that , Goto - SPRO-Production -BAsic Data-Work center-Capacity Planning-Define Capacity categories -Create Capacity Categoery for common pool of welders , Create Capacity in CR11 and assing them into Work cetre Capaicty tab-Pooled Capacity Catogeries and maintian No of indivuial caapcity in Capacity Header -Standard Available caapcity-Indivual Capacity ( Total Number of welders with working timing , utilisation ) .
Quest2 : To address this issue , you can select Setup , Labour and Machine in Defalut tab of same Work centre with proper Standard Value Key .Now , as they are all part of the Production activity , so you can keep the same Cost Centre ( Production Cost Centre ) in the Work centre tab with Formula Key of Labour ,Machine and setup .Goto CR02-Default Tab and Costing tab .
Hope this is clear
regards
JH

Capacity Leveling of Work Center

Hi all,
I have a problem with Capacity of Work center (WC).
I have a Internal Activity, and i assigned a WC for this Internal Activity. WC's capacity is 100H/day for 1 number of element.
Work of this WC is 250H, duration 5 days, number of element 1. Default capacity of this WC is distributed by Distribution Key define in Activity. . And they are divided equally between factory days in 5 day. That is capacity requirement is 50H/Day
So, i want to edit this WC's capacity following value:
Day 1: 100H/day
Day 2: 50H/day
day 3: 0H/day
day 4: 0H/day
day 5: 100H/day
How can i do it?? I try to use Dispatch Manually but i cant solve this problem.
Please help me for this case.
Thank all.
NLQ

Dear
Capacity leveling depends on some of the basic set up of Capacity Requirement Planning .You need to have proper CRP set up frist .
Couple of check points : -
Did you work centre is relevent for finitie scheduling in CR02-Capacity Header and wht is the over laod percentage for work centre ?
Did you have Capacity Requirement Related Set up like Over all profile , time profile , Startegy Profile -OPD0?
Did your Capacity Check -OPJK -Order Control at order level are active for availibilty Check 1 and 2 and assinged Over all Profile ?
Set up :
1.Please assing a operation control key like PP01 where Details Capacity Check and scheduling is active .
2.In CR02-Work centre -Capacity Header -You should have Follow check box marked
1.Releven for Finitie Scheduleing
2.Can be used for multiple Operation
3.
3.OPU3/OPU5 -Define Scheduling paramter -Mark Scheduling and Capcity Check for planned order or production Order
4.In SPRO -Shop Floor Control-Define Production Scheduling Profile -You need to matian the relevent Parameters like
1.Schedueling Automatically 2.Scheduling Log 3.Adjust Scheduling -Basic date , Depedent Requirement date 4.Scheduling Type -Backward etc .
These are all basic level set up beside CRP overall profile and other profile like strategy /time etc which may in place as you are analysing in CM01.
Please find below some of the useful CRP details : Refer this threads which are self explaintory :
http://help.sap.com/saphelp_47x200/helpdata/en/8a/a5a3154adc11d189740000e8322d00/frameset.htm
http://www.scribd.com/doc/17026521/SAP-ECC-60-PP-Capacity-Planning-httpsapdocsinfo
capacity planning
http://help.sap.com/printdocu/core/print46c/en/data/pdf/PPCRPSFC/PPCRP_SFC.pdf
Capacity Planning
capacity requirements planning
How to dispatch operation to do Capacity Leveling at Work Centre Level :
1.Frist Check the over load at work centre . Goto -CM07/CM05-give plant only -then hit the Stnadard view -You will find weekly or daily baiss load ( Requirement , Avaliable Capcity , Overlaod etc )
2.Check the week in which days you are tring to dipatch -if you selet the week check box and double clik it will show u all the dataiul load .Basde on the available capacity in other week-days u need to dipatch in CM22/CM31 or CM25/CM21
While dipatching in CM22/CM31-Select the Stragegy button on the top header -Mark Date entry when dispatching so that when you select the operation of any production order or planned order for certain work centre , it will pop with window having information of Date , Work Centre , Time .Onec you did this you will receive Scheduling log with certain information .
Hope this helps
regards
JH

Updating Work Center Capacity Header Data (UoM : KAPEH)

Hi All,
Using an LSMW all the Work Center were created, but it was having a wrong value for the Capacity header data unit of measure KAPEH. Due to that it's giving an error of " In table T006, entry ****** is missing".
I tried to maintain the Time Dimension using SPRO but I can't create the value which has been passed as HR (Hours), because it's already used by some other UoM.
What would be the way one should update the value of KAPEH.
Thanks & Regards
Harry

in the t. code CUNI or OPCF
Select the time intead of AAAADL , - Next to unit of measurement
and click Unit of measurement
and Create a new time unit as HR
It will solve your problem
or create a LSMW for CR02 to change the field KAPEH HR to H
this will solve your problem

Update Routing data after change in Work Center

Hello All,
I have just modified the Costing Data for 100 Work Centers CR02, setting a new "Activity Type" and "Activity Unit". But the Routing Data CA02 does not get updated correspondingly. I would like to ask is there any standard program which can help me to do the mass processing as to update the data to the corresponding routing?
Thanks.

1) You can change as per Mr Anupam sharma Said
or
2) YOU can also Update the data IN CA85N
In selection criteria enter the respective work center and Plant
and In new Value Give
Same work center, Plant, activity value , Unit and activity type
execute
select the all the work center and then click mass change
Edited by: Sundaresan . E. V on Nov 12, 2010 10:25 AM

Work center's description copy automatically in operation Routing

Hi all,
Could anyboy tell me where point of spro is to customize that work center's description is copied automatically in the operation Routing's description?
I try to search for it but I don't find it still.
Thanks in advance

Hi,
A suggestion:
In CA10, create a key say Z1 & give the description same as work center's description.
Now go to CR02 & for the work center in default values tab, assign the key to the field Standard Text key.
Now when you create a routing which uses this work center, the operation description will contain the work center description.
Regards,
Vivek

Work Center CR02

Similar Messages

Maybe you are looking for