Work Center Shift Definition
Hi PP Expert,
I have requirement for this shift :
Shift 1 : 08.00 to 17.00
Shift 2 : 20.00 to 04.00 next day
How do you define it in SAP ?
Should i create that like this ?
Shift 1 : 00.00 to 04.00
Shift 2 : 08.00 to 17.00
Shift 3 : 20.00 to 24.00
Is it normally maintain like that or is there any way to create in two shift definition?
Regards,
Arman Lie
Dear Arman,
During shift definition generally the previous shift end time will be taken as the next shift start time,but in your case the first shift
starts at 08:00 and ends at 17:00.
The second shift is starting at 20:00(Night 8'o clock) and ending at 04:00 in the morning.How do you treat the time between 17:00
to 20:00?
Check out in this way,In OP4A,create the grouping logic->shift defiition->
S1 first shift 01.08.2011 31.12.9999 08:00:00 17:00:00 9.00
S2 second shift 01.08.2011 31.12.9999 20:00:00 04:00:00 8.00
Then under Shift Sequence,
2S 1 2 shift sequence S1 S1 S1 S1 S1 S1
2S 2 S2 S2 S2 S2 S2 S2
Assign this in the work center capacity header,by definish the shift start as 08:00:00 and end time as 04:00:00 by mentioning the
duration of break,then in the grouping mention the respective shift grouping,in the intervals and shifts mention the start date and
end date and select the shift sequence.
Now in CM01 accordingly you will be able to see the available capacity,assuming you have not defined any break timings either in
the shift sequence or else in the capacity header in the work center.
Check and revert back with your queries.
Regards
Mangalraj.S
Similar Messages
-
how we configure the shifts in work center. please describe the whole procedure.
thanks in advanceDear,
You need to define a shift in OP4A - define new grouping
click on New entries...let us say 99, give some text
Select 99 and double click on shift definition
click on new entry
shift - 1, text - first shift, start date-010108, end date - 31129999, start=07:00:00, finish-15:00:00
shift - 2, text - second shift, start date-010108, end date - 31129999, start=15:00:00, finish-23:00:00
shift - 3, text -Generalshift, start date-010108, end date - 31129999, start=08:30:00, finish-16:30:00
Double click on shift Sequence
Seq-1shift-1,des-shift-1,day1-1,day2-1,day3-1,day4-1,day5-1,day6-1,day7-1
Seq-1shift-2,des-shift-2,day1-2,day2-2,day3-2,day4-2,day5-2,day6-2,day7-2
Seq-1shift-3,des-shift-3,day1-3,day2-3,day3-3,day4-3,day5-3.(hope only 5 days working for General shift)
save this.
In work center change transaction capacity view
assign this grouping no 99.
Enter active version = 1
Click on interval and shift push button (left top)
follow the menu path Edit>insert>insert interval
enter valid from and valid from field enter shift sequence and remove the data if there in any other filed and click on ENTER. all the days in week are defaulted with the shift seq you defined.
Hope it is clear, or come back
Please check this link also,
[Shift Sequence|https://forums.sdn.sap.com/click.jspa?searchID=16735253&messageID=3810730]
Regards,
R.Brahmankar -
Work center capacity header freezed
Dear Gurus,
we're not able to edit the work center capacity header. not able to edit the start and finish times.
it is happening only for one work center. in other work centers same capacity category is editable.
Please help us in resolving this.
Regards,
GowriHi,
Check your work center categeroy definition for which edit is not possible.
The work center category determines which data can be maintained in a work center.
Each work center category is assigned to the applications (for example, production, plant maintenance or quality management) whose menus allow you to maintain work centers with this category.
Each work center category has a number of screens assigned to it which the system displays when work centers of this category are displayed. The screens contain groups of fields (for example, scheduling data). Depending on the work center category, you can make field selections on these screens (for example, defining required entry fields).
Thanks,
nandha -
Overtime accounting in work center
Dear friends,
I am running my shop floor in 2 shifts. But some time i will plan for over time working also.
How to capture this over time working in SAP_PP(Work center shifts) module?
How to capture who has worked on this over time ?
Please clarify
Thanks
SenthilHi Narashiman,
Thanks. Now i am working on your idea. If it works i will award your more points.
You assume that within 5 dyas i have to produce 100 components.
In first 2 days i have produced 40 components.
third day 20 components, fouth day 20 components and fifth day 20 components.
So as per your statement, in CO11 (Production order confirmation_operation level), if i select partial confirmation i have to enter yield quantity as 40 for first 2 days then respective days.
Then i have to select final confirmation on last day (ie is fifth day).
Is it correct?
Thanks
Shri -
Difference of work center Vs Cost center
Hi,
Let me know what is the difference between cost center vs work center with definition?
Thanks and regards
RameshCost Center One of the three types of cost objects currently used in the SAP system. Cost centers are centrally allocated funds, budgeted on the fiscal year.
Cost centers are used to track where cost occur in the organization.
As costs are incurred, they are assigned or posted to the appropriate cost center.
The posting and assignment of costs to cost centers is a critical step in using the CO module.
Cost centers are organized in a Standard Hierarchy.
The Cost Center Standard Hierarchy is used to structure the cost centers in an organization.
All cost centers must be entered in the Standard Hierarchy.
To display the standard hierarchy follow the menu path:
Accounting ->Controlling ->Cost Center Accounting ->Master data ->Standard Hierarchy ->Display
Work center its specific to which application you are using.
Logistics - General (LO)
An organizational unit that defines where and when an operation must be performed.
The work center has an available capacity. The activities performed at or by the work center are valuated by charge rates, which are determined by cost centers and activity types. Work centers can be:
Machines
People
Production lines
Groups of craftsmen
Quality Management (QM)
A place at which inspections are conducted.
In the SAP System, work centers are entered in the inspection operations. Several inspection characteristics can be inspected for each work center or inspection operation.
Warehouse Management
A physical unit in the warehouse, in which warehouse activities such as packing, distribution, and weighing, can be performed.
Example
Packing station
*Look into the following link for SAP Glossary *
http://www.sapfans.com/sapfans/sapfaq/sapgloss.htm#sectW
Hope this helps
Vinodh Balakrishnan -
Hi all,
Im little confused with the capacity header in work center. In the capacity header there is one place to give start time, end time, length of break and number of individual capacity. And in grouping key i can define the shift and shift sequence. So if im maintaining both of these ( standard avilable capacity and grouping key), which will be considered to calaculate avilable capacity?Hi
If you are running three shifts ,please maintain the data as given belwo
start :00:00:00
End:23:59:59
Break :03:00:00 ( 1 Hour per shift so 3 hrs for 3 shifts)
No.of individual capacity :1
System will understand that it is round the clock operation with total three hour brak and you will get 21 hour per capacity
Hope this helps
regards
Prakash -
Shift sequence query in PP work center
Dear All,
I am having one problem while maintaining shift sequence in work center. I have maintain all config settings in OP4A shift 1 shift 2 shift 3 but when I create work center and select shift sequence, it is only taking shift 1 and not all 3 shift for all 7 days.
Can anyone tell me the solution?
Thanks in advance.
Regards,
MaxDear Santosh,
Thanks for the valuable inputs.
I have created following sequence in OP4A.
1, Create a Group eg. CB
2.Create a shift definitions like SHIFT1,SHIFT2,SHIFT2, START/END DATE, START/FINISH TIME OF SHIFTS, NO BREAKS ARE THERE and assign it to group.
3. Define individual shifts SEQUENCE DAYWISE wrt to groupo.
4..Assign grouping in capacity header of work center.
5.Now go to add interval option and create a new version of capcity which contains desired shift sequence from the shift group assigned.
7. assign proper valid froma and valid to dates.
8. In capacity header screena ssign the newly created capcity vesrion as active vesrion.
BUT STILL i WILL ABLE TO MAINTAIN ONLY FIRST SHIFT SEQUENCE FOR ALL 7 DAYS.
SYSTEM IS NOT SHOWING 2ND AND 3RD SHIFT.
PLEASE HELP ME OUT.
THANKS
MAX -
Work Center Capacity Shift Interval
Hello,
I'm looking for a function or Tables from which I can get Work Center Capacity Shift & Interval data, Transaction CRC3.
Any help in this regard will be highly appreciated.
Regards,
Hashir Ahmed.hi,
check these tables.
AFIH Transparent table Maintenance order header Application table (master and transaction data)
AFKO Transparent table Order header data PP orders Application table (master and transaction data)
AFRU Transparent table Order Confirmations Application table (master and transaction data)
AFVC Transparent table Operation within an order Application table (master and transaction data)
CABN Transparent table Characteristic Application table (master and transaction data)
CBPR Transparent table CO-ABC: Activity Master Table Application table (master and transaction data)
COEP Transparent table CO Object: Line Items (by Period) Application table (master and transaction data)
CRCA Transparent table Work Center Capacity Allocation Application table (master and transaction data)
CRHD Transparent table Work Center Header Application table (master and transaction data)
CSKS Transparent table Cost Center Master Data Application table (master and transaction data)
CSSL Transparent table Cost Center / Activity Type Application table (master and transaction data) -
Regarding Shifts in a work center
Hi experts,
I am facing an issue regarding the shift in workcenter.
I have done all the prerequisite settings in spro like
1. defing a grouping key,
2 defining work break schedule key,
3.definining shift definition,
4.defining shift sequence
now is there something called shift pattern key which does the shift changing on the desired basis like monthly or daily or weekly.
i have created one for my requirement.but whenever I am aasigning my grouping key to the workcenter only one shift reflect in the system.
So can you please help me.
Regards,
VivekHi Vivek,
This seems to be a different question all together,you have to create new thread for each question to get proper/prompt reply
First of all before cerating an inspection plan,you have to first decide what type of inspection you want to do
You can find the std inspection types in the QM view of the material master under Insp.setup
Then maintain the respective inspection type
like Inspection after GR from production
After that create inspection plan for the material in QP01 tcode
Before that you should have inspection characteristics created(MIC's)
It is created in QS21 tcode,here you will have to mention whether its qualitative or quantitative & input data accordingly
In QP01 you have to maintain the usage accordingly like 5,6 etc
Rest is like normal routing
In case of inproces inspection you dont need to create a seperate inspection plan,you can maintain the same in the production routing with MIC's
Hope this hepls
Rgds,
SVP -
Rotating Off-Days in PM Work Center Available Capacity
Good Day!
Background:
Each Maintenance person is represented by a PM Work Center.
Maintenance person have a rotating off-days which cycle repeats after 21 days.
Requirement:
We want to reflect rotating off-days to PM Work Center Available Capacity.
Options tried but did not worked;
Shift Definition Grouping: Off-days is in HR's Period Work Schedule but only Daily Work Schedule can be pulled into Shift Definition Grouping and then into Work Center
Reference Available Capacity: Can be achieved via Shift Sequence Key in interval of available capacity but needs to maintain for each week with on-going maintenance
Do anyone has implemented this similar requirement that we can reapply/build on?
Your valuable inputs are deeply appreciated.
Thanks!In work center capacity header
click change intervals
click insert
Enter manually
valid from and valid to dates
No of ind capacity - 0 -
Factory Calender assigned to Plant & resource/Work center
Hello,
If we have assigned the Factory Calender "XX" which has 5 working day(Monday to Friday) with no Special rules & no Holiday Calender to Plant & "YY" Factory Calender to Work center which has 365 days working with no no Special rules & no Holiday Calender.Now, when MRP creates Planned Orders for FERT material It did not create it on Weekends(i.e. on Saturday & Sunday) though the factory calender assigned is "YY" (which has 365 days working )in work center.Why?
Actually it should have consider the Work center assigned Calender for Capacity planning & Schedulling purpose.
If I assign the Factory Calender "YY" to plant then it will create the procurement proposal on weekends which is not acceptable to external procurement MRP Controller as plant office works only 5 days.
Please guide.Dear
Goto CR02/03 , select the Capacity tabe "hat" and u will fined there is tabe "Available Capacity " .U have to maintain the Active version ok.
Basically , the active version is used for scheduling and capacity planning. If you have not entered an active version, the standard available capacity is used, even if an available capacity version has been entered.
At the same u have to check out the below requirement :
you must maintain the following data in the capacity header:
1.The grouping, that defines which shift sequences and shift definitions can be used to maintain the available capacity
2.The number of the active version of available capacity
3.The base unit of measure of the available capacity
3.The factory calendar, that is the basis of the available capacity-Workcentre
If you do not enter a factory calendar , the system uses the default calendar for the plant.
I hope in your case , u have the shift sequence of 5 work days for the calander you have assinged in work centre .
Please check all those n come back .
Reward points if usefull.
Regards
Jia -
In the simplest of scenario, I have craeted a Shift grouping with 1 Hr break; So, the available work hours is 23 Hrs.
I have selected the same shift definition on all the seven days.
Now, I have added the shift grouping in the capacity header details in the Work center. But in the work center, I do not see the available capacity as 23 Hrs.
Am I missing something?
Kindly help on this.1.Go to the capacity header data and create your shift in the capacity shift interval data.
2. Only after doing this you will be able to see the capacity
reg
Dsk -
Shift definition implementation
Hi All,
I want to implement shift definition as new functionality as per client requirement. Existing work center data is maintained with shift time as start time, break and end time. Also no of individual capacity.
Now with above master data setting client has work for past 2 yrs. Now they want to implement shift definition with shift sequence.
My query is while implementing shift, what to do with exiting open data like production order, capacity etc.
What are the step follow to implement the same. Plz suggest.
Regds,
RajeshHi Rajesh,
Case 1; Your understanding is absolutely correct. The changes that you bring in now would be into effect with the date of implementation. So all the existing open orders would be working in the old system of shift. All the orders created from the date of implementation would be having the new definition of shift.
Now case 2 is the capacity. If all your workcenters are having infinite capacity, you are not going to have any problem in Capacity at alll... Now the realy problem is when you have some or all of these workcenters as finite capacity from the effective date of shift change.
In this case, you can have 2 plans
Plan A) Wait till all old orders are closed in the system (You cannot have proper capacity planning output till such time). At the same time keep collecting the capacity data for new orders. So you can have your capacity requirements and planning in place only after all the old orders are closed.
Plan B) Migrate all the data required for capacity planning for the old orders, so that you can have an up to date system. But this is a herculean task as you need to post status of all your open orders...
So just think about it before you go with your plan... I would rather convince client for plan A...
regards
Prasanna -
Same work center being used in different routings
Hi
I have requirement like this:
Workcenter WC1 works in two shifts Shist A & B.
It is being used in two routings for different products X & Y.
Product X will be prodiced in shift A.
Product Y will be produced in Shift B.
How to schedule it for different shifts for different products.
Thankls in advance.
Regards
YMREDDYsince workcentre is not working on the material based.
but the routing worked on the material based
give the shifting timing and the break timing in the work center alone
you have to select the matrl product x in the routing and the sequence of operation for the product is mentioned that the product that be there for the working in the
shift A .
product Y is to be sequenced to work at that w.c at shift B -
Parallel processing in the same work center
Dear Guys,
There is a routing sequence in which some 2-3 operations will occur parallely & those operations will belong to a same work center,How to map those operations in the routing,do i need to maintain parallel processing ,if so then how to go aboutParallel Sequence
Definition
A linear sequence of operations that is parallel to a sequence of operations in the standard sequence.
Use
A parallel sequence enables you to process several operations at the same time. A parallel sequence is carried out at the same time as the corresponding section in the standard sequence. It is a special form of overlapping operations.
Integration
You can create parallel sequences in routings and rate routings. You cannot create them in reference operation sets or reference rate routings. Creating a Parallel Sequence
Call up the sequence overview.
Choose Edit ® New entries.
The Choose Sequence Category dialog box appears.
Select Parallel sequence and press Continue.
The Sequence Details screen is displayed.
Enter the necessary data.
Select Operation overview to create operations for the parallel sequence.
so particularly in your case
WORK CENTRE OF 10, 20, 30 ,40, 50 ASSUME TO THERE
OPERATION OF THE SEQU : 1,2,3,4,5
SUPPOSE 3,4 ARE PARALLEL SEQUN AND THE WORK CENTRE 30,40 ARE SAME TYPRE TO OPR SAME
YOU MAY DESIGN AS
WC-30
(OPN3)
W.C 10 WC 20 WC50
(OPN1) (OPN2) (OPN5)
WC 40
(OPN4)
OR
WC-30
(OPN4)
W.C 10 WC 20 WC50
(OPN1) (OPN2) (OPN5)
WC 40
(OPN3)
Maybe you are looking for
-
Create a Crystal report to display the sum of G/L account code within a specific period
Hi, Just wonder is it possible to create a crystal report to display the total of a G/L account code within a specific period? How to write the query to get the sum within a specific period? For example: Period: 2014-06-01-2014-06-10 Account code A:
-
"The server responded with an error" - Calendar
I get the error message "The server responded with an error" every five minutes from the calendar app, along with the following: "The URL https://calendar.google.com/calendar/dav/[my e-mail is here]/user/ encountered HTTP error 404. Make sure the URL
-
I'm wondering if there is any way to make a histogram scatter plot like this one in Numbers: http://www.clinsci.org/cs/099/0505/cs0990505f01.gif At the moment I have a bunch of values in three columns. This seems like it should be super straightforwa
-
Help with using autosum in excel 2008 on mac mountain lion
I am coming from pc world... love my new mac....and excel autosum is not working on my new macbook pro. I click autosum at the bottom of a column with 8 numbers highlighted as I did on pc. And the correct sum shows in the cell where I want the total.
-
Web Dynpro ALV disable column sort for specific column
Hi, I have the above mentioned problem. The Coding I use is: DATA: lr_field_settings TYPE REF TO if_salv_wd_field_settings, lt_fields TYPE SALV_WD_T_FIELD_REF. FIELD-SYMBOLS: <fs_field> LIKE LINE OF lt_fields. lr_field_settin