Workforceviewer didn't run properly
Hi everyone,
After I enabled the workforce overview, I feel like it's not running very well. The rendering is so slow and sometimes it leave the screen blank. I go to SLG1 and found the error message bellow.
How could I fix these issues?
Thanks,
Punleu CHOMNAN
Hi Punleu,
can you please test the evaluation-path MSS-DIREC for the respective manager with report RHSTRU00? After that, what happens when you test O-S-P with the orgunit of the manager? Are you getting results? On this way, we can check, that the data in your org-management are correct...
Regards
Michael
Similar Messages
-
Basically I had to reformat my hard drive, and in order to do that I copied all the files from it to a disk image which I then used to restore through disk utility.
Now this worked as far as individual files go, but the OS for some reason didn't copy properly. After restoring from the image, the machine started up with an infinite pinwheel and apple logo, not going anywhere, so I eventually just reinstalled snow leopard from the original installer. This is fine as far as the system itself goes, but I'm having some very annoying issues - for one, some things which I had registered have reverted to trial versions (probably just a question of moving some preference files from the backup which got overwritten, shouldn't be too hard) but far more seriously, a bunch of kext extensions aren't loading, including one which is needed to run my external wifi antenna (the internal one is banjaxed, won't connect to any network unless you're sitting beside the router at all times).
Here's the console log. Why are these kexts not working, when they worked perfectly before the reformat? Still struggling to understand why copying the entire root dir to a disk image and then restoring from that image did not, as expected, yield an identical system, and why I even had to reinstall after doing this. But more urgently, how do I get these extensions working again? Using airport isn't sustainable, I can't sit on the stairs every time I want to use the internet
12/06/2013 11:16:57
com.apple.kextd[12]
Failed to load /System/Library/Extensions/RT2870USBWirelessDriver.kext - (libkern/kext) authentication failure (file ownership/permissions).
12/06/2013 11:16:57
com.apple.kextd[12]
Load com.Ralink.driver.RT2870USBWirelessDriver failed; removing personalities.
12/06/2013 11:16:58
kernel
Previous Shutdown Cause: 5
12/06/2013 11:16:58
kernel
Warning - kext com.apple.driver.AppleIntelIntegratedFramebuffer has immediate dependencies on both com.apple.kernel* and com.apple.kpi.* components; use only one style.
12/06/2013 11:16:58
kernel
Warning - kext com.apple.driver.AppleIntelGMA950 has immediate dependencies on both com.apple.kernel* and com.apple.kpi.* components; use only one style.
12/06/2013 11:16:58
kernel
Atheros: mac 12.2 phy 8.1 radio 12.0
12/06/2013 11:16:58
bootlog[40]
BOOT_TIME: 1371032202 0
12/06/2013 11:17:03
blued[41]
Apple Bluetooth daemon started
12/06/2013 11:17:03
com.apple.SecurityServer[27]
Session 0x5fbff962 created
12/06/2013 11:17:04
com.apple.kextd[12]
Failed to load /System/Library/Extensions/BoomDevice.kext - (libkern/kext) authentication failure (file ownership/permissions).
12/06/2013 11:17:04
com.apple.kextd[12]
Load com.globaldelight.driver.BoomDevice failed; removing personalities.
12/06/2013 11:17:04
mDNSResponder[30]
mDNSResponder mDNSResponder-212.1 (Jul 24 2009 22:34:12) starting
12/06/2013 11:17:04
com.apple.usbmuxd[23]
usbmuxd-296.3 on Jul 25 2012 at 00:28:37, running 64 bit
12/06/2013 11:17:04
/System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[31]
Login Window Application Started
12/06/2013 11:17:04
com.apple.kextd[12]
Failed to load /System/Library/Extensions/RT2870USBWirelessDriver.kext - (libkern/kext) authentication failure (file ownership/permissions).
12/06/2013 11:17:04
com.apple.kextd[12]
Load com.Ralink.driver.RT2870USBWirelessDriver failed; removing personalities.
12/06/2013 11:17:04
com.apple.kextd[12]
Failed to load /System/Library/Extensions/BoomDevice.kext - (libkern/kext) authentication failure (file ownership/permissions).
12/06/2013 11:17:04
com.apple.kextd[12]
Load com.globaldelight.driver.BoomDevice failed; removing personalities.
As you can guess, Ralink USB Wireless Driver is the one I'm having trouble with, although the other error you see, BoomDevice, is one of the apps which had been registered but has reverted to trial. The errors in console made me think it was a permissions issue, but repairing permissions, despite taking half an hour and modifying tons of files, did not resolve this issue.
How do I fix this, and also out of interest, why did it happen in the first place? I imagined formatting and restoring would be far, far less complicated than this O_o
EDIT: Should point out that obviously going from 10.6.8, the reinstall reverted to 10.6, and I haven't been able to upgrade since I can't get this internet kext working. Shouldn't be a problem though since the wireless driver was for 10.6.x...Still struggling to understand why copying the entire root dir to a disk image and then restoring from that image did not, as expected, yield an identical system, and why I even had to reinstall after doing this.
Because there is a lot more going on under the hood than merely copying files.
The only way to do what you want is to use cloning software like Carbon Copy Cloner.
My advice is to rescue your personal files to a regular non-TimeMachine external drive, Zero erase the ENTIRE drive and install OS X fresh and update, then your programs from original sources and files from backup.
Then, make a bootable clone and you can copy that as many times as you want and each one is bootable.
Most commonly used backup methods
How to erase and install Snow Leopard 10.6 -
LabVIEW application fails to run properly at Windows startup
I have experienced problems with my Labview application after putting it in the Windows XP startup folder. The application runs perfectly if I start it manually but whenever I get Windows XP to start it after boot-up, I see various error messages. My application uses calls to the NIMotion library and it's these calls that are generating the error messages. I don't always get the same errors and the problem has occurred with two different programs on two different computers. I think it is something to do with NI services for the motion controller that load at startup and haven't yet been started before my application runs. I have configured Windows to login automatically and I have noticed thay my program executes quite early, sometimes even before the desktop icons appear.
I have seen that a number of other users have experienced similar problems. There was a recent post titled "Waiting for Windows Idle" in the LabWindoesCVI forum that is related. The only solution that I have come across is to wait at the very start of the program until the rest of the dependent services have loaded. I have added a 30 second wait to my programs and this appears to have largely solved the problem. This is no the best solution because it is not always guaranteed to work. I have had a situation recently where Windows was installing an automatic update and the bootup process was slower than normal. This caused my program to fall over again. I don't wan't to extend this time too much or the user will be waiting every time the machine is turned on.
Another solution would be to check for those specific errors that are generated and keep trying the function calls until they are successful. I have not tried to do this yet. It would probably be quite time consuming process to write the code to process the errors because I need to build an executable and reboot everytime I want to test. And again this method is not guaranteed to catch all errors. Surely there must be a better way. I have done some initial investigation into the Windows Service Manager but haven't got too far. I've discovered I'm not a Windows programmer and I don't know what all those NI services listed under "Administrative Tools" actually do. Surely there must be some better way or some tool out there that can check that Windows has finished loading?
David ReevesSorry dreeves, I don't have an answer for you. I would like to know the solution myself. I had similar problems recovering from a standby state.
DAQmx takes a while to get going for USB devices and the queue functions didn't recover properly at all. I just sat in a loop checking the status of my attached devices until they initialised properly then moved on from there.
It would be great if there was some way to check the status if the various LabVIEW modules that load on startup. Then, when all the ones you need are ready, continue with the rest of your application.
I would think checking LabVIEW for its status would be more reliable then asking Windows if it has finished starting up.
Troy
CLDEach snowflake in an avalanche pleads not guilty. - Stanislaw J. Lec
I haven't failed, I've found 10,000 ways that don't work - Thomas Edison
Beware of the man who won't be bothered with details. - William Feather
The greatest of faults is to be conscious of none. - Thomas Carlyle -
Hello! I downloaded OS X Mavericks on my Mac and my pc didn't restart properly.my desktop image doesn't appear and i can't shut down my pc. what can i do ?
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
For this step, the title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter "BOOT_TIME" (without the quotes.)
Each message in the log begins with the date and time when it was entered. Note the timestamps of the BOOT_TIME log messages, which refer to the times when the system was started. Now clear the search box and scroll back in the log to the last boot time when you had the problem. Select the messages logged before the boot, during the time something abnormal was happening. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
For example, if the system was unresponsive or was failing to shut down for three minutes before you forced a restart, post the messages timestamped within three minutes before the boot time, not after. Please include the BOOT_TIME message at the end of the log extract—not at the beginning.
If there are long runs of repeated messages, please post only one example of each. Don’t post many repetitions of the same message.
☞ When posting a log extract, be selective. A few dozen lines are almost always more than enough.
☞ Some private information, such as your name, may appear in the log. Anonymize before posting.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Step 2
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A crash report has a name that begins with the name of the crashed process and ends in ".crash". A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent of each. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
I know the report is long, maybe several hundred lines. Please post all of it anyway.
☞ If you don't see any reports listed, but you know there was a crash or panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
☞ Please don’t post other kinds of diagnostic report—they're very long and rarely helpful. -
SharedVariableNode didn't get properly patched to DS
I'm receiving very occasional errors as follows:
#Date: THU, JAN 01, 1970 12:00:13 AM
#OSName: VxWorks
#OSVers: 6.3
#OSBuild: Jun 14 2012, 08:43:39
#AppName: /c/ni-rt/system/lvrt.out
#Version: 12.0rc7
#AppKind: AppLib
<DEBUG_OUTPUT>
01/01/70 12:04:48.865 AM
DWarn 0xE3E2BC8B: SharedVariableNode didn't get properly patched to DS
source/variable/SharedVariableCallbacks.cpp(99) : DWarn 0xE3E2BC8B: SharedVariableNode didn't get properly patched to DS
I am using Shared Variables ... they are Single Process SVs with RT Enabled (these are not Network Published). This will occur in perhaps 1 in 100 runs, so difficult to isolate. I am using SVs to maintain current values only for communication across deterministic processes.
Do SVs need to be initialized?
Can anyone decode the error message ...?If this system is critical refrain from using Shared Variable Engine. I have a project in which I used the shared variable engine and every few weeks the shared variable engine goes down, I looked into it for a few weeks, but the behavior of the shared variable engine is exteremly erratic when it comes to error handling. If you research NIs white papers enough, they warn you about the reliability and throughput of the shared variable engine. Try using the Network Stream VI's. they are still fairly simple to implement but as far as performance go, they far exceed shared vairables. they are the closest thing to using TCP/IP directly, but much simpler to implement.
Good luck,
Dan,
www.movimed.com - Custom Imaging Solutions -
Is this an iTunes or disc issue? I have burned music to these disc before.
Error message: "The attempt to burn a disc failed. The disc drive didn't respond properly and can't recover or retry."
Using........
iTunes 10.7
Memorex Music CD-R 40X 700MB 80min
MacBook Pro
Mac OS X 10.7.5
2.4 GHz Core i5
4 GB 1333 MHz DDR3Not sure. Try this:
Troubleshooting CD burning errors:
http://support.apple.com/kb/HT2955 -
27-inch, Late 2009
Processor 2.66 GHz Core i5
8 GB memory
Software OS X 10.9.5
iTunes 11.4
Can not burn a playlist in iTunes 11.4 to a CD, upon completion of the burn operation get error message, "The attempt to burn a disc failed. The disc drive didn't respond properly and can't recover or retry." Receive this message using 2 different external drives that are Apple compatible. 1. is a Pioneer SuperDrive that I had replaced from a previous Mac in a OWC enclosure, 2. the other is a OWC 8X Slim Portable USB 2.0 External. After receiving the error message I can re-insert the disc into the drive and it will mount the disc and it will list all the songs with the correct size, but none of them will play. iTunes then comes up asking me if I want to import the CD, at this time iTunes has a (not responding) status in Finder. Can burn from finder with no problem, only have issue in iTunes.
Background
Last year I took the iMac to the local Apple Store 3 times and they determined the optical drive was defective and replaced it, the last time even replacing the cable to it. When I attempt to burn playlist from internal Superdrive it states it can not burn due to media errors. I have tried Memorex, TDK and PNY media with the same results. I thought purchasing the OWC Slim Portable USB 2.0 External would resolve the issue. If I put a commercial audio CD into the Internal Superdrive it will not mount and will eject it, if I insert the commercial audio CD into the external drive it will mount and play. Now the extended warranty is expired on the iMac and I don't know what next to try.After multiple attempts to both find an answer to this problem or to fix it myself I've given up and switched to a Windows PC. The same media works just fine at maximum write speed with no special tricks needed. I got my iMac specifically to manage my photographs and burn images for friends and family. It has been nothing but a big disappointment to say the least. To read messages saying I need to lower my write speed or buy more expensive CDs is just laughable. Unless I see something major change I'm sticking with my Windows PC.
-
I am trying to update to i-tunes 11.3 but when I download I get a message that itunes didn't install properly, and a reference to error 127. Any ideas?
For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
tt2 -
I recently updated to the newest version of Flash (17.0.0.134) and I have a MacBook Air, running OS X and I have Safari version 8.0.4. Ever since the update I can no longer select drop down menus or get Netflix to run properly. Has anyone else had this issue/know how to resolve it?
1. System Preferences > Flash Player > Advanced > Delete All
Press “Delete All” button under “Browsing Data and Settings”.
2. Install Adobe Flash Player.
System Preferences > Flash Player > Updates
Press the “Check Now” button.
http://get.adobe.com/flashplayer/
Download it and quit Safari from Safari menu in the menu bar.
Follow the prompts to install Adobe Flash Player. -
Hi,
Im unable to open the RPD online getting following error.
Note: Im not done any changes. Its works good till yesterday EOD.
Error:
[NQSError:13037] cannot connect to BI security service,Please make sure this is running properly (with SSL or not) in EM.
[NQSError:37001] could not connect to the oracle BI server instance..
Kindly help me to fix this issue.Hi,
Could you access the answer side.
Could you see the reports.
Do one thing, take a back up of NQS config file from <Oracle Location>\instance\instance1\config\obiserver folder\nqsconfig.ini file.
Copy nqs config file if you have already have a back up.
Restart the services and try once.
http://mkashu.blogspot.com
Regards,
VG -
Installed iTunes 11.0.2 and now macbook (2010 with osx 10.6.8) won't boot or run properly. any fix?
I still have 95 GB of free space on my disk. Booting takes minutes and no app or file will load/run properly. Just too slow. Spinning wheel for everything. I tried to repair disk, repair permissions, reset SMC and PRAM, as well as run the os software update. Has anyone come accross this? Any fix for this? Do I need to upgrade to Mountain Lion? Any insight would be appreciated. thx
Okay. problem fixed. Had to re-install osx from the original installation dvd and then ran a software update. Now machine and iTunes works fine. I came across the fix as part of this great step by step to fix your mac diagnosis post. very useful.
-
As I said, I have a CD which is marked Photoshop Elements 4.0, Windows XP. My operating system is Windows 8.1, Will the program on the CD run properly? If not, who will it take to upgrade it? [email protected]
It probably won't work, but you can give it a try.
Upgrade here (although you may be able to find a full version less expensively at an online store or a retail store):
Buying guide: version comparison | Adobe Photoshop Elements 13 -
I disconnected my iPhone in the middle of an iTunes update. Now it wont run properly what do I do? I was working online and I recieved a pop up from iTunes stating that there was an harwared update for my iPhone. I had it plugged up for a while , long enoung for me to watch a tv show have dinner and come back. I thought the update was complete and came back to the computer and unplugged it. The next morning I saw a picture of aUSB cord and the iTunes icon. I have no use of my phone and cannot get access to emails, internet contacts..nothing . Help !
Well it should NEVER be unplugged when doing something.
It actually had not installed the software at that stage, it had been copied over to the iPhone, it was being checked and then it would be installed.
You need to connect your iPhone to the computer at home and hope that you can install the software again and then restore your backup.
If you install iTunes at work you may be able to Restore the software but you will most likely lose the content on your iPhone as you do not have a backup to restore on that computer, or all your media / apps. -
Hi.
I have problems to get my Laser Jet 5L running properly under 10.5.8. I prints the first page/document and then it says1,36 % printed than printing but nothing happens. Under 10.4.11 everything works fine, sometimes I have to get the print jobs running again,but then it works.
I have the Laser Jet 5L connected via USB to parallel.
I am running a PowerBook G4 1,67 GHz and 2 GByte RAM.
Best regards
LasertJet5LAppleHello, since nobody has piped in yet...
Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions.
Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions.
Any devices that previously appeared in your Printer List and Fax List will need to be added again after resetting the printing system.
Resetting the printing system in Mac OS X 10.5.x
1. To use the Reset Printing System feature in Mac OS X 10.5.x, follow these steps:
2. Choose System Preferences from the Apple menu.
3. Choose Print & Fax from the View menu.
4. Control-click on list of printers on the left side of the window, then choose "Reset printing system" from the contextual menu. If you don't see a list of printers, Control-click on the text "Click + to add a printer or fax" and select "Reset printing system..." As an alternative, if you currently have one or more printers listed, you can Option-click the "-" (Remove printer) button.
http://support.apple.com/kb/ht1341
Reboot. -
FOR ALL ENTRIES stmnt. in SELECT query is not running properly
Hello experts,
In my report program, I write one query on table BSIS.
Internal table declaration -
DATA : BEGIN OF DLC_BSIS OCCURS 0,
BUKRS LIKE BSIS-BUKRS,
GJAHR LIKE BSIS-GJAHR,
BELNR LIKE BSIS-BELNR,
SHKZG LIKE BSIS-SHKZG,
BSCHL LIKE BSIS-BSCHL,
AUFNR LIKE BSIS-AUFNR,
HKONT LIKE BSIS-HKONT,
QSSKZ LIKE BSIS-QSSKZ,
DMBTR LIKE BSIS-DMBTR,
END OF DLC_BSIS.
Query as follows --
SELECT BUKRS
GJAHR
BELNR
AHKZG
BSCHL
AUFNR
HKONT
QSSKZ
DMBTR FROM BSIS
INTO TABLE DLC_BSIS
FOR ALL ENTRIES IN IT_BKPF2
WHERE BELNR = IT_BKPF2-BELNR
AND BUKRS = IT_BKPF2-BUKRS
AND GJAHR = IT_BKPF2-GJAHR.
IT_BKPF2 internal table having -- BUKRS - LT01
BELNR - 6400000061
GJAHR - 2009.
And in BSIS database table -- 3 entries are there for the above documnet.
But, in my internal only one entry has come for the same above document.
I think For all entries stmnt. is not running properly. But Why it's not running properly.??
What would be the reason..??
Thanks in advance....!!
Regards,
Poonam.>
Poonam Patil wrote:
> Hello experts,
> In my report program, I write one query on table BSIS.
>
> Internal table declaration -
>
> DATA : BEGIN OF DLC_BSIS OCCURS 0,
> BUKRS LIKE BSIS-BUKRS,
> GJAHR LIKE BSIS-GJAHR,
> BELNR LIKE BSIS-BELNR,
> SHKZG LIKE BSIS-SHKZG,
> BSCHL LIKE BSIS-BSCHL,
> AUFNR LIKE BSIS-AUFNR,
> HKONT LIKE BSIS-HKONT,
> QSSKZ LIKE BSIS-QSSKZ,
> DMBTR LIKE BSIS-DMBTR,
> END OF DLC_BSIS.
>
> Query as follows --
>
> SELECT BUKRS
> GJAHR
> BELNR
> AHKZG
> BSCHL
> AUFNR
> HKONT
> QSSKZ
> DMBTR FROM BSIS
> INTO TABLE DLC_BSIS
> FOR ALL ENTRIES IN IT_BKPF2
> WHERE BELNR = IT_BKPF2-BELNR
> AND BUKRS = IT_BKPF2-BUKRS
> AND GJAHR = IT_BKPF2-GJAHR.
>
> IT_BKPF2 internal table having -- BUKRS - LT01
> BELNR - 6400000061
> GJAHR - 2009.
>
> And in BSIS database table -- 3 entries are there for the above documnet.
>
> But, in my internal only one entry has come for the same above document.
>
> I think For all entries stmnt. is not running properly. But Why it's not running properly.??
> What would be the reason..??
>
>
> Thanks in advance....!!
>
> Regards,
> Poonam.
include the buzei field in selection criteria i have faced the same situation earlier.
always select all the key fields.
varun
Maybe you are looking for
-
Got this yoga tab 2 1050f for my wife for Christmas Shes been having WiFi problems with it for awhile now so over the last couple weeks I've been using it I run a speed check on it and its good but opening webpages is very slow over 10seconds a lot
-
Hi all, When i am trying to call a RFC FM, it askes me for an additional logon of the target system before giving the results. Please let me know is it necessary to give additional logon details or do i need to cange any settings in SM59. Thanks in a
-
How to Start EDI Batch from API
Hi, I'm creating EDI batch configuration dynamically through API (using TpmContext object), but could not find a method which can start a newly created batch. from the UI, newly created batch is visible at Parties > Agreement > A->B > Batch Configura
-
EOFException when deserializing object in if statement
Hi, I'm a java newbie and I've got a program in which I've got an method to open a serialized file. I am running into problems when determining the class of the object to be deserialized. When the code is as such everything works fine: ObjectInpu
-
Recently I've been suffering from a strange phenomenon when viewing QuickTime content on the web - so far I've only encountered it only on Apple's trailers website. I have "Autoplay" option turned off on my workstation, but when I try to view some tr