WPA/WPA2 not an option in encryption type, only WEP

Can anyone please let me know how to get my Airport Extreme card to connect to my WiFi router using WPA2? So far, when I select my network, the only encryption options I can select when it prompts me to enter a password are all WEP encryption types, and LEAP. How do I get it to offer WPA2 as an option for the encryption?
Thanks!
Mike

I had to rename my network and update software for the airport extreme.

Similar Messages

Log onto incoming mail server (POP3): Your server does not support the connection encryption type you have specified. Try changing the encryption method. Contact your mail server administrator or Internet service provider (ISP) for additional assistance.

Hi All,
This is my first post to ms exchange forum am getting Log onto incoming mail server (POP3): Your server does not support the connection encryption type you have specified. Try changing the encryption method. Contact your mail server administrator
or Internet service provider (ISP) for additional assistance. in my outlook clients, till last Sunday (12.04.15) my exchange was well & good, Monday morning suddenly the problem started like none of our outlook pop3 clients are able to communicate
with exchange (rest IMAP, SMTP & Exchange accounts are working fine). i have tried with all port no but no luck. please help me to get raid of this one.
Exchange 2013 CU6 with server 2012 Std 64Bit
Thanks,
Murali

Dear All,
I have found the solution for above problem, the problem has occur due to PopProxy inactivity
please find relevant exchange management shell commends below.
1. Get-ServerComponentstate -Identity <yourmailserver.com>
Server Component State
yourmailserver.com ServerWideOffline Active
yourmailserver.com HubTransport Active
yourmailserver.com FrontendTransport Active
yourmailserver.com Monitoring Active
yourmailserver.com RecoveryActionsEnabled Active
yourmailserver.com AutoDiscoverProxy Active
yourmailserver.com ActiveSyncProxy Active
yourmailserver.com EcpProxy Active
yourmailserver.com EwsProxy Active
yourmailserver.com ImapProxy Active
yourmailserver.com OabProxy Active
yourmailserver.com OwaProxy Active
yourmailserver.com PopProxy Inactive
yourmailserver.com PushNotificationsProxy Active
yourmailserver.com RpsProxy Active
yourmailserver.com RwsProxy Active
yourmailserver.com RpcProxy Active
yourmailserver.com UMCallRouter Active
yourmailserver.com XropProxy Active
yourmailserver.com HttpProxyAvailabilityGroup Active
yourmailserver.com ForwardSyncDaemon Active
yourmailserver.com ProvisioningRps Active
yourmailserver.com MapiProxy Active
yourmailserver.com EdgeTransport Active
yourmailserver.com HighAvailability Active
yourmailserver.com SharedCache Active
2. Set-ServerComponentState -Identity <yourmailserver.com> -Component PopProxy -Requester HealthAPI
-State Active
3. Get-ServerComponentstate -Identity <yourmailserver.com>
Server Component State
yourmailserver.com ServerWideOffline Active
yourmailserver.com HubTransport Active
yourmailserver.com FrontendTransport Active
yourmailserver.com Monitoring Active
yourmailserver.com RecoveryActionsEnabled Active
yourmailserver.com AutoDiscoverProxy Active
yourmailserver.com ActiveSyncProxy Active
yourmailserver.com EcpProxy Active
yourmailserver.com EwsProxy Active
yourmailserver.com ImapProxy Active
yourmailserver.com OabProxy Active
yourmailserver.com OwaProxy Active
yourmailserver.com PopProxy Active
yourmailserver.com PushNotificationsProxy Active
yourmailserver.com RpsProxy Active
yourmailserver.com RwsProxy Active
yourmailserver.com RpcProxy Active
yourmailserver.com UMCallRouter Active
yourmailserver.com XropProxy Active
yourmailserver.com HttpProxyAvailabilityGroup Active
yourmailserver.com ForwardSyncDaemon Active
yourmailserver.com ProvisioningRps Active
yourmailserver.com MapiProxy Active
yourmailserver.com EdgeTransport Active
yourmailserver.com HighAvailability Active
yourmailserver.com SharedCache Activ
Replace yourmailserver.com with your server host name.
Thanks

WPA, WPA2 not working, only WEP.

Hi everyone,
First off i'd like to say that i've done alot of searching and cannot for the life of me figure out why i can't configure my router to have working WPA or WPA2 security, only WEP seems to be a working option. Up until today i've had a WEP key, but feel WPA or WPA2 would be more secure, as I live on campus at a university. I have a D-Link DI-624 router, and am running 10.6.4. I tried both DHCP and manually entering IP addresses, but it all comes down to the fact that i keep getting either "Airport has a self-assigned IP address and may not be able to connect to the internet." or ""Airport does not have an IP address and cannot connect to the internet." Usually when I can get it to connect after trying over and over, the airport will give me either of these messages and results in 169.254. . being the assigned IP address causing the conflict. I will answer any questions necessary to resolving my conflict. Any help is appreciated.

It appears the firmware update is a temporary fix, as the router will keep working for a while, but every so often it will just connect to my wpa2 security enabled network, but will only give me the "no ip address" message or the other message that indicates i can't connect to the internet. my fix to this is to simply reset the router with the pin-sized button in the back, thus having to re-create the network and add all the details again. anyway i was wondering if any one could offer any more insight on this problem. it is very frustrating to keep resetting the router every two days just to connect to the internet. any help is appreciated.

Tip on using US Robotics Modem (WPA/WPA2 not supported)

Dear all,
As I can see from the discussions many of us have gone through the pain of installing Time Capsule wishing we had instead bought a good hard disk.
I have a US Robotics MaxG which serves as a router and I plan to put the time machine in a different room away as well from my MacBook Pro. I mean after all that is the point of wireless (not havig to connect the time capsule to the US Robotics modem).
Unfortunately, I managed to isolate a problem and found a workaround to it. It seems that Time Capsule does not like WPA2/WPA passwords.
So what you need to do is to use instead WPA2 encryption with TKIP and AES selected.
Thanks and good luck,
Sergio

Dear jdimstrnate,
Based on your description both the AUX port and the modem are not configured correctly. You can find detailed instructions for this setup in the following link from Cisco:
http://www.cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a0080094bbc.shtml
In summary, the AUX port needs to be set at a speed of 115200 and the modem must be configured with AT&F1S0=1&W.
If you need further assistance please feel free to contact our technical support line, 1-888-216-2850. Our hours of operation are Monday through Friday, 9 AM to 5 PM CST. You can also contact us by email using our online email form from the following link:
http://www.usr.com/support/s-online_EmailTechie.asp
I hope this helps.

Measuring Point during IK01 not allowing characteristics with CHAR type

Hi Experts,
Measuring Point during IK01 not allowing characteristics with CHAR type Only allows NUM,
could you anyone suggest on this.
Regards
Nitin

May i know the reason of such implementation?
You can use group code and valuation code for assigning predefined values to measuring documents.
Moreover text field can be used for assigning short text to it.

Wireless Networking - unable to select an encryption type for WPA/WPA2

I recently upgraded to 10.5.3 and didn't notice until now that Network preferences no longer provides an option for specifying the encryption method (TKIP or AES-CMP) for a new wireless network? I don't recall ever having had this issue before. Is this new to 10.5.3 or has this been a recognized problem prior to 10.5.3? I can only select from WPA Personal or Enterprise, WPA2 Personal or Enterprise (ignoring the WEP options here).
Is there another area of the OS that I can modify to change the encryption type?
This is weird...

While I was able to get WEP to work, it would only switch to WEP for both bands, and I wasn't too excited about this option. So to max out security, what I did was keep my dual band Airport Extreme running on WPA2 (5GHz N-only for all my Mac equipment; a wireless G for ipod touch). I then bought a linksys/cisco WRT54G2 for about $40 new from Amazon, and connected it with ethernet to the Airport Extreme base. Took a little fiddling to get it to behave as a bridge (can describe for you how I did this if you go down this route). But most importantly, maxed out security for WEP on this device by not broadcasting the SSID (don't on my other network either), having a very obscure SSID name (think strong password), set an equally obscure random password of all character types, setup up MAC filter so it could only be connected to my Pronto (and one of my notebooks for configuration). Also run it on a different 2.4ghz channel than the Airport Extreme to minimize conflict. Copied the info over to the Pronto config program (I use bootcamp to do this on my notebook), and everything works great. I do wish Apple gave us complete control over both bands (like the level of config I've done here), but the solution here was still pretty clean. My understanding is that Philips is planning to add WPA/WPA2 to Pronto capability by year-end (the connect/re-connect times are slower and they didn't want their products taking a performance hit, but I'd happily wait an extra second or two after picking up the remote to not expose my network via WEP). Hope that helps, but probably not what you wanted to hear. I found it a fairly quick and inexpensive workaround for now.

Unable to connect to Wi-Fi connection using WPA2 PSK authentication and encryption type TKIP

I was referred to here from this thread at the Windows Insider Program: http://answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_web/unable-to-connect-to-wi-fi-connection-using-wpa2/07bae1ed-c7fb-4f85-9d26-5549cc23e57a?msgId=2eb70420-fe35-494b-a13d-dcacd4d55eb9&rtAction=1426697691002
My issue is copy/pasted below:
Original Title: TKIP selection in WiFi network settings
I have a workplace WiFi connection using WPA2 PSK authentication and encryption type TKIP.
On the machine I used to test Windows 10, I had a previous installation of Windows 7 professional which connected to my workplace WiFi using the above settings. After installing Windows 10, my workplace wifi settings were imported and worked fine.
Windows 10 had a system crash, and since I had deleted my previous windows installation, I performed a complete reinstall of Windows 7. However, when I went to install Windows 10 again, I had not taken the time to set up my workplace Wifi on Windows
7 before installing Windows 10. As a result, I had to set up my workplace wifi as a new connection in Windows 10.
When going to set up the wifi connection, the encryption type was grayed out, but appeared to default to AES. Searching the internet suggested that Windows 8.1 did not need a encryption type selected, because Windows could automatically determine
if it was TKIP or AES, hence why the option to select encryption type was grayed out. However, after completing the setup of my workplace wifi, Windows 10 could not connect to my workplace wifi. After restoring Windows 7 with a factory reset, and setting up
the workplace wifi (the encryption type selection was not grayed out and I manually selected TKIP encryption), my workplace wifi was working again.

I was referred to here from this thread at the Windows Insider Program: http://answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_web/unable-to-connect-to-wi-fi-connection-using-wpa2/07bae1ed-c7fb-4f85-9d26-5549cc23e57a?msgId=2eb70420-fe35-494b-a13d-dcacd4d55eb9&rtAction=1426697691002
My issue is copy/pasted below:
Original Title: TKIP selection in WiFi network settings
I have a workplace WiFi connection using WPA2 PSK authentication and encryption type TKIP.
On the machine I used to test Windows 10, I had a previous installation of Windows 7 professional which connected to my workplace WiFi using the above settings. After installing Windows 10, my workplace wifi settings were imported and worked fine.
Windows 10 had a system crash, and since I had deleted my previous windows installation, I performed a complete reinstall of Windows 7. However, when I went to install Windows 10 again, I had not taken the time to set up my workplace Wifi on Windows
7 before installing Windows 10. As a result, I had to set up my workplace wifi as a new connection in Windows 10.
When going to set up the wifi connection, the encryption type was grayed out, but appeared to default to AES. Searching the internet suggested that Windows 8.1 did not need a encryption type selected, because Windows could automatically determine
if it was TKIP or AES, hence why the option to select encryption type was grayed out. However, after completing the setup of my workplace wifi, Windows 10 could not connect to my workplace wifi. After restoring Windows 7 with a factory reset, and setting up
the workplace wifi (the encryption type selection was not grayed out and I manually selected TKIP encryption), my workplace wifi was working again.

Wireless-Card doesn't not work with WPA/WPA2 but with WEP [Solved]

Hello I have a MacBook (late 2007) with a wireless-card from Broadcam, the card works with WEP and the classic configuration over rc.conf very well. But I can't get the card running with WPA and the net network-profiles.
Here is the link to the driver - http://www.broadcom.com/support/802.11/linux_sta.php
eth2 = wireless-card
eth1 = firewireanything
eth0 = wired-card
rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
#MODULES=(sky2 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="macbook"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="eth0 192.168.1.220 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(!eth0 !eth1 eth2)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
NETWORKS=(wireless)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network net-profiles netfs alsa crond portmap fam hal)
/etc/network.d/wireless
CONNECTION="wireless"
INTERFACE=eth2
HOSTNAME=macbook
IP="static"
IFOPTS="192.168.1.225 netmask 255.255.255.0 broadcast 192.168.1.255"
GATEWAY=192.168.1.1
DNS1=192.168.1.1
# Wireless Settings (optional)
ESSID=3Com
#KEY=
IWOPTS="mode managed essid $ESSID channel 11"
#WIFI_INTERFACE=wlan0 # use this if you have a special wireless interface
# that is linked to the real $INTERFACE
#WIFI_WAIT=5 # seconds to wait for the wireless card to
# associate before bringing the interface up
USEWPA="yes" # start wpa_supplicant with the profile
WPAOPTS="" # use "" for normal operation or specify additional
# options (eg, "-D ipw")
# see /etc/wpa_supplicant.conf for configuration
Can I set here the WPA/WPA2-Key also? Why here ESSID? Do I need still a configuration in wpa_supplicant.conf?
Thats very confusing and not explained.
WPAOPTS? Do I need to add something like "-D wext"?
/etc/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
network={
key_mgmt=NONE
priority=-9999999
network={
ssid="3Com"
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="topsecret"
priority=5
# WPA2
# proto=WPA RSN
I need help. Please
Last edited by hoschi (2009-01-04 20:21:58)

fwojciec wrote:If this info is not in the wiki it might be worth it to add it -- it's all detailed in /etc/network.d/examples/complete.example though.
Thats the reason why I was so confused.
My new and well working configuration:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
#MODULES=(sky2 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="macbook"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="eth0 192.168.1.220 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(!eth0 !eth1 !eth2)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
NETWORKS=(3com)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network net-profiles netfs alsa crond portmap fam hal)
CONNECTION="wireless"
DESCRIPTION="Very verbose complete wireless example"
INTERFACE=eth2
HOSTNAME=macbook
# Interface Settings (use IP="dhcp" for DHCP)
IP="static"
IFOPTS="192.168.1.225 netmask 255.255.255.0 broadcast 192.168.1.255"
GATEWAY=192.168.1.1
# DNS Settings (optional)
DOMAIN=localdomain
DNS1=192.168.1.1
DNS2=
SEARCH=
# Standard Wireless Settings
ESSID=3Com
SECURITY=wpa-config # One of wep, wpa, wpa-config, none
KEY=""
# Scans to see if network is available before connecting (reccomended)
SCAN="YES"
# Time to wait to connect to a network. Default 15.
TIMEOUT=10
# Pass *custom* options to iwconfig. Usually not needed (optional)
IWOPTS="mode managed essid $ESSID channel 6 key restricted $KEY"
# Any extra arguments for wpa_supplicant
WPA_OPTS=
# For SECURITY='wpa-config' only - filename of a wpa-supplicant config
WPA_CONF=/etc/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
network={
key_mgmt=NONE
priority=-9999999
network={
ssid="Linksys"
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="areulookingatmybreasts"
priority=5
network={
ssid="3Com"
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="nomam"
priority=5
# WPA2
# proto=WPA RSN
There are also profiles for the Linksys-Router and for wired cable.
Thanks for the help!
Last edited by hoschi (2009-01-04 20:21:23)

HP Officejet Pro 8600 will not allow WPA2_PSK encryption type selection.

HP Officejet Pro 8600 e-All-In-One-Printer-N911a
Macbook Pro: Mac OS X 10.6.8
Netgear WNR3500L Wireless Router
Purchased printer: 12/9/2011
Install CD version matches current Mac software download version from HP website.
Initial software installation with CD went fine with no problems. Next CD install step: Manually configuring printer using USB
cable acquired wireless router, but HP software displays "Encryption Type: WPA_PSK" There is no other selection available.
My router is configured for WPA2_PSK (AES). I downloaded a manual from HP that says this printer supports WEP, WPA and
WPA2. Does this printer support WPA2? If so, what do I need to do to select WPA2_PSK?
This question was solved.
View Solution.

Try connecting the printer to your network from the printer front panel: Setup > Network > Wireless Setup Wizard.
After completing this, run the software which will find your printer alread on your network.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Could not access wifi (wpa,wpa2)

hi, all
im developing an access point(ap), but i have critical problem...
in auth mode WPA(personal, enterprise mode, and aes, tkip, tkip-aes), WPA2(personal, enterprise mode, and aes, tkip, tkip-aes), any devices can connect to my ap except for iphone
i could not understand why only iphone disassociated my ap
belows are logs...
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: 500368.098888 wlan.N[10295] AppleBCMWLAN Joined BSS:     @ 0x812f4200, BSSID = 00:90:a3:47:4f:c1, rssi = -45, rate = 54 (100%), channel = 4, encryption = 0x8, ap = 1, failures =   0, age = 42, ssid[ 6] = "cc3900"
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: AirPort: Link Up on en0
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: en0::startOutputQueues (0)
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: IO80211PeerManager::doEnable
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: en0: BSSID changed to 00:90:a3:47:4f:c1
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: en0::IO80211Interface::postMessage bssid changed
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: en0: BSSID changed to 00:90:a3:47:4f:c1
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: en0::IO80211Interface::postMessage bssid changed
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: IO80211Peer::queuePacket ff:ff:ff:ff:ff:ff alllocate queue for ac 0
Apr 5 10:05:05 jingyun-ui-iPhone configd[48] <Notice>: network changed: v4(pdp_ip0:163.222.71.173, en0-:192.168.0.66) DNS! Proxy-
Apr 5 10:05:05 jingyun-ui-iPhone configd[48] <Notice>: Captive: CNPluginHandler en0: Inactive
Apr 5 10:05:05 jingyun-ui-iPhone configd[48] <Notice>: network changed: v4(pdp_ip0:163.222.71.173) DNS Proxy
Apr 5 10:05:05 jingyun-ui-iPhone mDNSResponder[31] <Error>: DeregisterInterface: Frequent transitions for interface en0 (192.168.0.66)
Apr 5 10:05:05 jingyun-ui-iPhone mDNSResponder[31] <Error>: mDNS_RegisterInterface: Frequent transitions for interface en0 (FE80:0000:0000:0000:3ED0:F8FF:FE24:E898)
Apr 5 10:05:05 jingyun-ui-iPhone kernel[0] <Debug>: 500368.199680 wlan.N[10296] AppleBCMWLANCore:startRoamScan(): 3365 Delaying RoamScan; because Join Mgr Busy 1 isWaitingforIP 1
Apr 5 10:05:08 jingyun-ui-iPhone Preferences[12524] <Warning>: -[APOtherNetworkController keyboardWillShow:]
Apr 5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: 500371.085227 wlan.N[10297] AppleBCMWLANNetManager::handleDisassoc(): status = 0, reason = 15, flags = 0x0, authtype = 0, addr = 00:90:a3:47:4f:c1
Apr 5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: 500371.089803 wlan.N[10298] AppleBCMWLANNetManager::leaveNetworkAsync(): kDeauthdCurrNetwork already set. Skipping call to leaveNetworkASync
Apr 5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: 500371.089933 wlan.N[10299] AppleBCMWLAN Left BSS:       @ 0x812f4200, BSSID = 00:90:a3:47:4f:c1, rssi = -45, rate = 54 (100%), channel = 4, encryption = 0x8, ap = 1, failures =   0, age = 45, ssid[ 6] = "cc3900"
Apr 5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: 500371.090008 wlan.A[10300] AppleBCMWLANCore::deleteAllPktFilters(): Deleted IPv4/IPv6 and Magic packet filters
Apr 5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: AirPort: Link Down on en0. Reason 1 (Unspecified).
Apr 5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: en0::stopOutputQueues
Apr5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: IO80211PeerManager::doDisable
Apr 5 10:05:08 jingyun-ui-iPhone kernel[0] <Debug>: en0::IO80211Interface::postMessage bssid changed
Apr 5 10:05:08 jingyun-ui-iPhone Preferences[12524] <Warning>: WiFi: Joined (null)
Apr 5 10:05:09 jingyun-ui-iPhone Preferences[12524] <Warning>: -[VPNConnectionStore reloadVPN]: The active VPN configuration has changed from to (null)
Apr 5 10:05:09 jingyun-ui-iPhone Preferences[12524] <Warning>: -[VPNBundleController _vpnConfigurationChanged:] (0x1ed9d110:<VPNBundleController: 0x1ed9d110>): _serviceCount(0), serviceCount(0), toggleInRootMenu(0), RootMenuItem(1)
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: 500372.046796 wlan.N[10301] AppleBCMWLANCore::setASSOCIATE(): [wifid]: lowerAuth = AUTHTYPE_OPEN, upperAuth = AUTHTYPE_WPA2_PSK, key = CIPHER_PMK , don't disassociate    .
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: 500372.130819 wlan.A[10302] AppleBCMWLANNetManager::prepareToBringUpLink(): Delaying powersave entry in order to get an IP address
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: 500372.130940 wlan.N[10303] AppleBCMWLAN Joined BSS:     @ 0x81459000, BSSID = 00:08:9f:d2:f4:a0, rssi = -73, rate = 54 (100%), channel = 9, encryption = 0xc, ap = 1, failures =   0, age = 0, ssid[ 6] = "iptime"
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: AirPort: Link Up on en0
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: en0::startOutputQueues (0)
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: IO80211PeerManager::doEnable
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: en0: BSSID changed to 00:08:9f:d2:f4:a0
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: en0::IO80211Interface::postMessage bssid changed
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: en0: BSSID changed to 00:08:9f:d2:f4:a0
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: en0::IO80211Interface::postMessage bssid changed
Apr 5 10:05:09 jingyun-ui-iPhone kernel[0] <Debug>: IO80211Peer::queuePacket ff:ff:ff:ff:ff:ff alllocate queue for ac 0
Apr 5 10:05:10 jingyun-ui-iPhone kernel[0] <Debug>: 500372.210844 wlan.N[10304] AppleBCMWLANCore:startRoamScan(): 3365 Delaying RoamScan; because Join Mgr Busy 1 isWaitingforIP 1
Apr 5 10:05:10 jingyun-ui-iPhone kernel[0] <Debug>: 500372.376670 wlan.N[10305] AppleBCMWLANJoinManager::handleSupplicantEvent(): status = 6, reason = 0, flags = 0x0, authtype = 0, addr = 00:00:2c:f4:02:00
Apr 5 10:05:10 jingyun-ui-iPhone profiled[12552] <Notice>: (Note ) profiled: Service starting...
so my question is that what means for reason=15 (wlan.N[10297] AppleBCMWLANNetManager::handleDisassoc(): status = 0, reason = 15, flags = 0x0, authtype = 0, addr = 00:90:a3:47:4f:c1)
, and why handleDisassoc function is called with reason=15?
android, windows could connect my ap, so i think there is no problem with wpa,wpa2 authentication packets.
are there ideas?
ps1. what is the best way to debug this problem for windows?
ps2. please save me. this problem makes my lifespan decrease.

    Mifrett, don't panic. I'm here to assist you. It sounds like the software update may be conflicting with the software of the applications that were previously downloaded to your device. I recommend that you uninstall a few applications in Settings>Manage Apps> tap the app>tap uninstall application. Once you have uninstalled a few applications, power your device off/on. You may redownload the applications that you previously had. However, this time, the applications will be downloaded to your phone with the latest app software. I trust that these steps will improve the performance of your device. Keep us posted. We're here for you.
LasinaH_VZW
VZW Support
Follow us on Twitter @VZWSUPPORT

WPA/WPA2 encryption for (WiFi) Ad-hoc?

Is there any Apps that can create WPA/WPA2 encryption for (WiFi) Ad-hoc connection beside default WEP? I'm aware that WEP is not as good as WPA/WPA2 encryption......... i'm using my neighbours WiFi connection for free...

If you want WPA, then your key_mgmt and pairwise are definitely wrong. I'd say don't set key_mgmt, pairwise and group at all, the defaults are ok.

Xbox live not working in WPA/WPA2 personal mode.

Xbox Live is not working in WPA/WPA2 personal mode. It does, however, work in WEP mode. I have 2 windows laptops on my wireless network. when I am on WEP, the laptop is stuck in a perpetual "Acquiring Network Address" state. When I have WPA/WPA2 enabled, my laptops work fine, but xbox live cuts in and out of detecting my network, and I cant even get close to connecting at all.
So until I figure this out, I have to choose between WEP (xbox live working, and not PCs) WPA(PCs working, not xbox live) or unsecured (risky). what should I do?

Thats strange topcat, i have exactly the same problem as you except that when i am in WEP encryption my xbox cant even see the extreme on the network and i cant even get it it to connect at all. In WPA mode the xbox sees the network but will not connect. I have rang xbox and they say that it should work and that the problem lies with Apple, although i dont believe this personally. In the meantime ive had to hardwire the xbox to the router which isnt why i bought the router. Disappointed
Regards
Stu

WVC54GCA Missing WPA/WPA2 security options in web interface

I just got a WVC54GCA and found out that there are some missing configuration options in the wireless settings:
On the cameras web interface:
web interface > Basic : Wireless Settings > [ Edit Security Settings ] > Security Mode:
the dropdown gives me only two options: Disable and WEP, but no WPA, WPA2!
I upgraded to the latest firmware (1.1.00 build 02), but the problem remains.
Tried different browsers (Firefox 3.5, IE8) with the same result.
Is this a firmware bug? A faulty device? Anyone else having the same issue?
Solved!
Go to Solution.

Try to clear the Browser settings of your IE and then try to login to the setup page of your Camera, and check if you are able to find that options.... If still unable to find WPA/WPA2 Option on your camera, Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your camera, wait for 60 seconds and re-connect the power cable....
Now check if you are able to find that options... If still not then i think it might be the problem with the Camera... I think you need to replace your Camera.

WPA/WPA2 PSK NOT SUPPORTED?

I'm trying to join a router with WPA/WPA2 PSK, but for some reason NONE of my iOS devices will join it. Not my iPad 3, nor iPhone 5S, all running iOS 8.1.1.
My MacBook Pro running Yosemite has no problem connecting. So does iOS 8, nor iPhones and iPads support this recommended security standard? Or is there a trick to it I'm not getting?

Restart the router & also check for a firmware update for it.
If neither of those helps, try temporarily removing the password from the router to see if your iOS devices will connect.
~Lyssa

HT2534 I already made an accoount, so how can I change it so that I do not have to choose a type of credit card. Cause it does not give me the option of NONE

I already made an accoount, so how can I change it so that I do not have to choose a type of credit card. Cause it does not give me the option of NONE

Did you follow the instructions on that page exactly ? The instructions work for me e.g. selecting a free app in the App Store app and tapping on 'free', then 'install app' and 'create new apple id' - filling in my details then gave a 'none' option on the payment details :

WPA/WPA2 not an option in encryption type, only WEP

Similar Messages

Maybe you are looking for