WPA2 - Webcam - Base Station - Remote Base Station ... How ?

My Webcam is plugged into my Remote Base Station and uploads images over my WDS network to my Base Station perfectly ... and I can use my browser to access the Webcam's Control Panel - until I enable Wireless Security!
Once Wireless Security is enabled on my Base Station and I have updated my WDS settings on the Remote Base Station, my browser can no longer access the Webcam and the camera's images are no longer transmitted to my Base Station.
The type of Security makes no difference. I've had no luck with either WEP and WPA2.
The only type of Security that allows the camera to use the WDS network is no Security!!
Question:
After I have enabled Wireless Security on the Base Station, does the Remote Base Station's Wireless Security also have to be enabled ?
---alan

From the Camera Manufacturer:
"Hi Alan,
I'm not sure what is causing this. The camera doesn't know about the wireless. Any encryption is between the client and the base. Devices connected to the client should not be affected."
Well - Thanks to that helpful tip, I have eventually determined that the correct procedure is:
Step 1: Apply the encryption to the Remote Base Station that has the Netcam connected to it.
Step 2. Apply the same encryption & password to the Main Base Station ... the one with Internet via Ethernet.
Step 3. Rejoin my now 'closed' Network by selecting "Other" from the Airport menu in the Menu Bar.
Step 4. Select the Network name from that popup menu
Step 5. Enter my new WPA2 Personal Password.
Success!!
---alan
64 years old today!

Similar Messages

Dedicating an Airport Express Remote Base Station to a BB Curve

Hello all,
Please forgive me if this has been answered in another thread. I have been searching for the last week or so and have found that many people are experiencing the same frustration with the BB Curve and H@H (UMA) service. Someone recently suggested that I dedicate the Remote Base Station to my BB Curve so as to grant the UMA a fighting chance (my network consists of one Main and one Remote base station). In other words, the problem, as I understand it, is that UMA/voice data gets kicked off the network in favor of true data. If I can dedicate my extra (remote base station) airport express to my Blackberry, then the UMA should work more reliably.
Sooo...here is my question:
How do I assign my remote base station (set-up through WDS) to serve only my Blackberry Curve? Should I not do this? How do I find my Curve's MAC and IP address? Which address do I need? So on and so forth...
Thank you all who help.
james

No one seems to know what's going on! I'll retract it, then. Thank you for your consideration.

Remote base station versus relay base station

Okay, I give up. What is the difference between a remote and a relay? Can I daisy chain relay base stations? Will remote base stations act as "relays"? Are there any tricks to setting up the relay stations (remotes seem completely straightforward)? What are the positives and negatives of each?
MacBook Pro Mac OS X (10.4.7)

It seems like the distinction is more important if you want a wired connection to the station. If you're just tring to create a robust wireless network, can you do many remotes but just one relay? It seems like relay would be the way to go if there was no limitation on how many.

Old dome style Extremes used as a remote base station?

Can the old dome style Extreme's be used as a remote base station using WDS?
How would this be done?

Yes - the "dome style" Airport Extreme Base Station can be configured as a remote base station, with your Airport Extreme N base station functioning as the main base station.
The Airport Utility will guide you through the process.

Cannot connect 2nd Express as a Remote Base station

When I try to set up a 2nd express it doesn't connect.
I see in the Admin app that it has a "strange" IP address assigned. The Extreme Base station and the 1st Express have addresses like "192.168.9.x" and the new (2nd) Express has a 169.254.X.X and although you can see it in Admin you can't do anything to it.
I configured both the Express Remotes via Admin and use the "Auto config as Remote" feature in the WDS tab via the Extreme Base Station's configuration.
I also have an iMac with a hard-wired iMac connection to the Base Station.
Any ideas? Thanx.

I would do another reset and then configure the second Express manually. To configure the Express you have to be on the same network either with or without a wire.
Here are some steps to try and let us know the results:
- From your wireless laptop run Airport Admin Utility
- Select the Airport Extreme Bas Station (AEBS) and write down its "Airport ID"
- Open the configuration of the AEBS and note the channel number it is on. It should not be on "Automatic"
- Hard reset the 2nd Express
- Connect the Express to your laptop with an ethernet cable
- Both your laptop and the Express should be on the 169.254.x.x ethernet network since no DHCP server is available over their ethernet
- Open the configuration of the 2nd Express which has a name similar to "Airport Base xxxxxx" in Airport Admin Utility
- Change the Base Station name to something like "Express 2" and change the Base Station password so it's not the default "public"
- Leave the wireless mode as "Create a wireless network (Home Router)"
- Change the Network Name, wireless security and channel to match exactly what the other two Airports are set to
- Under the Internet tab change it to "Connect Using: Airport WDS"
- In the "MAC Address:" field enter the Airport ID of the AEBS
- Under the Network tab uncheck "Distribute IP Addresses"
- Under the WDS tab check "Enable this base station as a WDS Remote Base Station" and keep the check mark "Allow wireless clients on this base station"
- In the "Main Airport ID:" field enter the AEBS Airport ID again or click the Select button and pick it from the list (not the 1st Express)
- Under the Music tab set as desired
- Click the Update button finally and wait for it to update
- Disconnect the ethernet cable
- If necessary move the Express to it desired location
Did that help? If the "Auto configure as a WDS remote base station" from the Extreme doesn't work those are the manual steps to apply to an Express!

Relay vs Remote Base Station

I have setup a WDS network with my airport express units.
What is the difference between a relay station and a remote base station in a WDS network?
Thanks
Mike

Yes, so lets say I have two aiport express. One of them is in my bedroom and it gets good reception from my router. And the second one is in lets say my den, and it doesn't get so good reception from my router, but it is close to my bedroom... Would I have both the bedroom and den airport express as REMOTE, or would i put the bedroom one as a RELAY and the den as a REMOTE, or the other way around. I have a WDS network setup.. or does it matter?
Thanks

Cannot connect to remote base station

I have two airport express base stations.
The one in my office is setup as a WDS main base main base station and is connected to the internet.
The other one is installed in the kitchen as a WDS remote base station.
Both base stations allow wireless clients.
When I am in the reach of the main base station (in the office and in the kitchen), everything works fine.
However, when I go to the living room (here i am out of reach of the office base station, but within reach of the kitchen base station), my laptop still "sees" the network, but is unable to connect. An error is given: "There was an error joining the airport network"
I have re-configured the base stations several times; I also disabled the wireless security; I switched the base stations; .... no result
Who can help ????

I have the same problem at home. Somone else in this forum had a similar (though not absolutely identical) problem, for which another person suggested this:
"It sounds like the issue may be the communication between the Cable modem & the AirPort Extreme Base Station (AEBS). Since you already have reset the AEBS, I suggest that you try a complete power recycle of your network components.
"Modem/Router Power ReCycling
- Power-off the DSL/Cable modem, Internet Router, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the DSL/Cable modem; Wait at least 30 minutes.
- Power-on the Internet Router; Wait at least 5 minutes.
- Power-on the computer(s) "
Since I am not home, I can't try the above right now, but will do so when I return home in a few days. In the meantime, if you are able to solve your problem, either by trying the above procedure, or by some other method, will you please let me know?
Thanks a lot.
MacBook Pro Mac OS X (10.4.9)

Should I add third AE base as remote or relay?

I have an Airport network with two AE bases, one as the main and the second as the remote. I am planning on adding a third one and I have a doubt: should this also be a "remote" or a "relay" when added to the existing bases?
Thank you for your help!

If this third base station is going to be communicating directly with the main base station just as your existing remote base station - then it too should be added as a remote (and not a relay) base station.
A relay base station is used when you need to have a base station that communicates with a main base station as well as a remote base station - useful if you want to get even more range. In such a case, the remote base station would be configured to connect to the relay base station.

MB pro Airport utililty cannot recongnize my AX in remote base mode

I set up my AX as remote base of a existent wirless d link network, it worked for 2 days and now it is no more recognized from my macbook, is there an recent update trouble? Can u help me please?

I'm having the same problem after updating (my pb) to 10.5. and my airport express to the recent firmware.
I tried several types of resets. Afterwards, I can reconfigure the box - set everything up. AE is available afterwards for a minute or so but disappears then. This is so strange. It worked fine for two years or so.

Cash Basis and Accrual Basis Profit & Loss Statement

Dear Experts
can we generate Cash basis and accrual basis Profit and loss statement ? if possible then let me know how can we do in SAP Business one 8.8
Regards
Rajani PAtel

Dear Rajani,
B1 has no supports for the statement you need. You have to create your own report.
Thanks,
Gordon

ITunes 11.4 lost some Radio Stations in My Stations

I used to have 10-12 radio stations in My Stations. I woke up this morning and found there are only 6 stations left. Can someone suggest how I should investigate the issues? Thanks.

I just tried to re-add all the streaming stations back into my playlist and now it seems to be working!

HT1947 I see 2 apple tvs on my ipad, iphone, and within the remote app. How do I get rid of the "old" one?

I changed the AirPlay password on my apple tv, and now I see 2 apple tvs on my ipad, iphone, and within the remote app. How do I get rid of the "old" one?

Can be closed. Problem disapeared on its own!

I am the VICTIM of Remote Deployment. HOW do I get out of it??

I acquired the hacker in January. In February both of my computers were destroyed. I removed ALL forms of networking from my house -- TWC, all of my routers and adapters, etc.
I went to Best Buy and bought a new computer, then another, then 2 more -- all getting hit with a prefab image upon getting close to my doorway.
I am losing my home, etc, because I haven't been able to work in months. This hacker finds me at the library, and wherever else I try to work, and he messes withmy typing, stalls my screen, empties my USBs.
I believe I am the victim of remote deploymet, but how do I find where it is coming from?
I used my (corrupt) Gateway recovery disks the other day and watched how ActiveX and other rd tools were listed.
PLEASE, this has been going on for too long. After i gave up on computers, my house was entered nearly every day. The police literally think I am insane.
What can I do???
Warm regards,
Angel

Please call me directly at 919-637-0017.
I can't be sure to get logged on these days, but the answer to this question may possibly give me my LIFE back!
None

Base method and base value

Dear forum,
I would like to seek advice on the above.
I do not sure what is the difference between base method and base value in multilevel method.
What is the difference between these 2 base?
Thanks

Hi,
If you go ti AFAMA nd chosse a depr, key you can see the base Method as one component of the key.
Here is defined:
- Type of depreciation
- Dep. method and
- Treatment of end of depreciaion
If you take a look at the "multilevel method (also in AFAMA) you can see the base value.
The value used as the basis for the calculation of depreciation.
Regards Bernhard

Base Currency Or Base Amount Does Not Have a Value?

Hi
I've received the following error on the PRC: Distribute Borrowed and Lent Amounts process: Base Currency Or Base Amount Does Not Have a Value
Does anyone know what it means?

Hi
Do you have different currencies for your provider and receiver operating units?
Is there a difference between the transaction currency Ithe expenditure item) and the receiving OU currency?
Verify daily exchange rates exists for the relevant transaction dates.
Dina

WPA2 - Webcam - Base Station - Remote Base Station ... How ?

Similar Messages

Maybe you are looking for