WRE54G does not recongize WRT100 when WRT100 network mode is set to Mixed

The only time that WRE54 makes a connection to the WRT100 is when the Wireless Network Mode (under Wirless Settings) is set to BG-MIXED and the Standard Channel is identified.
If you selete MIXED for the Network mode all other setting within the WRT100 are set to auto and the WRG54 does not make a connection to the WRT100. So if you have a mixed enivorment with N B and G. The WRE54 will be useless.
Currently the expander does make a connection to the WRT100 when the Network Mode is set to BG-Mixed and the Standard Channel is identified.
Any Updates that will correct this commmunication problem would be benificial. So the one could have a truely mixed environment.

Hi Scrooge,
I have both pieces of hardware to the newest firmware. I tried your settings, however the WRE54G did not connect to WRT100. To reduce the amount of typing I didn't include Wireless --> Advance Wireless Settings within my note, I ensure you though I did exactly as you suggested.
On the WRT100
Wireless --> Basic Wirless Settings
Network Mode is Mixed
Network Name (SSID): HAM
Radio Band: Auto - 20/40Mhz Channel
Wide Channel: Auto
Standard Channel: Auto
SSID Broadcast: Enabled
Security --> Firewall (the only things I have mark are):
SPI Firewall Protection
Filter INDENT (PORT 113)
Please note that the filter Anonymous Internet Requests is not checked.
The WRE54G connects to WRT100 with these settings:
Wireless ---> Basic Wireless Settings
Network Mode: BG-MIXED
Network Name (SSID): Ham
Radio Band: IS NULLED OUT
WIDE Channel: IS NULLED OUT
Stardard Channel: 10 - 2.457GHz
SSID Broadcast: Enabled
suggestions?

Similar Messages

The alarm (as of iOS 7.0.2) does not go off when in vibrate mode

I have recently upgraded my iPhone 4S to iOS 7.0.2, and when the phone is in vibrate mode the alarms do not sound. Instead the phone just vibrates which does not help.
The point is to silence the phone for the night, as I don't want to hear incoming calls and texts, but I do expect the alarm to go off with sound in the morning. The alarm becomes completely useless otherwise.
Has anyone else experienced this, and is there some hidden new setting I'm unaware of to control this new behavior?

My alarm still sounds even if the phone is on mute. Have you tried resetting your device by pressing and holding the Home button and power button until the silver apple appears?
Until you get the issue resolved, have you tried using Do Not Disturb instead of putting the phone on mute? The alarm should sound when DND is set.
Best of luck.

My Macbook Air does not show up on my network to any of my other computers, Other computers on my network appear and disappear, some shared folders are not accessible

My Macbook Air with Lion does not show up on my network to any of my other computers (PC's) , even though it is connected to my wifi and does access the Internet. In addition, my other computers sometimes show up in Finder and sometimes they're not there. Sometimes they do show in Finder and when I click on them, I get "Connection Failed", other times, they connect. Also some shared folders on those other computers, which are PC's are not accessible, even though fully shared. My network is Apple Airport Extreme and works perfectly otherwise, including all PC's being able to see each other. Help would be much appreciated

I got the same problem. I want to access my shared folder on my home windows7 from my MBA. Tried many suggestions on the web but all to no avail. I thought that should be very trivial. Maybe a Lion bug?

Does not automatically connect to wireless network anymore

Mac Book does not automatically connect to know networks any longer.

Hi sashton,
When troubleshooting Wi-Fi connectivity issues, I find the following resource has the most relevant information:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
http://support.apple.com/kb/HT4628
Furthermore, you may want to avoid giving your network a common name. While the following article (and excerpt) refer to iOS devices, the same applies for your Mac:
Avoid giving your wireless network a common name (SSID)
http://support.apple.com/kb/HT4450
If you were to give your wireless network a common name (SSID), users of your network who use iOS devices [sic] and are away from your network would run the risk of joining a different network with the same name. Having joined the unexpected network, they would be exposed to potential data theft.
Because of this security issue, Apple maintains a list of common or ambiguous SSIDs, including the default SSID for many commercially available access points, as well as the SSIDs "wireless" and "default". If your network's name is on the list, any iOS device [sic] that joins the network stores the access point's BSSID and associates it with the network's SSID. Subsequently, it will only auto-join the network if the access point's BSSID matches the information the device has stored. This avoids joining a different network with the same name.
Therefore, you may want to refer to the following article when configuring your Wi-Fi router:
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
Thanks,
Matt M.

SP1 does not get installed when the machine is set to Japanese Language, software push through sccm 2012

Hi,
Please help me with the below issue, iam trying to deploy Service pack 1 on Windows 7 , 32 Bit OS
SP1 does not get installed when the machine is set to Japanese Language, software push through sccm 2012 , it does gets installed of installed manually, by remoting into the machine
also it gets installed through sccm when the machine is set to english language,
Thank you
Tanoj
OSLM ENGINEER - SCCM 2007 & 2012

Hi Friends,
we are deploying the SP1 via SCCM 2012 , and the success rate is around 50 %, its a Light touch installation where user will initiate the installation via Software Center ( Web based )
i was able to gather few errors , and this are the errors which failed during SP1 Installation 0x800f0828,
some errors which sccm reports display are
11171
10008
10021-
17031 -
1602 - User Cancelled installation
113 - No more internal file identifiers available
10070 - File handle reference is no longer available
10050 - A socket operation encountered a dead network
11170 - The task sequence manager could not successfully complete execution of the task sequence
i could not find the reason for some of the errors, also i am looking for a fix/woraround if any
Also i have noticed that in few computers the task seq failed at a place where after the sp1 installation a reboot happens and then PGP BYPASS utility is uninstalled, it did not start the PGP bypass uninstall after reboot
is there a way to cut short the Task seq and keep it simple ?
right now its like this
1. checking for prerequisite : checks for OS Name and OS version
2. installs PGP Bootgaurd Bypass
3. System Restart
4. Installing Windows 7 Service Pack 1
5. Final Restart
6. uninstall PGP Bootgaurd Bypass
Regards
Tanoj
OSLM ENGINEER - SCCM 2007 & 2012

OSX 10.9.1 macbook pro 13 retina - wifi does not reconnect automatically when waking up from sleep mode since I have a Bluetooth apple magicmouse

Hello,
My config is OSX 10.9.1 new macbook pro 13 retina (2014).
The wifi does not reconnect automatically when waking up from sleep mode since I have a Bluetooth apple magicmouse.
It was not the case before I bought the BT mouse.
Is this problem between Wifi and bluetooth coming from the OS?
Is there a fix already available or scheduled?
Thanks

Hello alexandrefromfrance
Check the Symptom: The network connection drops unexpectedly section for steps on what to do when your MacBook Pro does not connect after waking from sleep. I have also quoted the section on troubleshooting the issue as well.
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Symptom: After restarting or waking from sleep, my computer might not connect to the Internet
After waking from sleep or starting up, your computer may not show that it is connected to a Wi-Fi network.
After start or wake, your computer may indicate that it is connected to a network, but does not connect to the Internet.
Solution
Use these steps if your computer does not automatically connect to your desired Wi-Fi network.
Check your TCP/IP settings in the Network pane of the System Preferences. Click the "Renew DHCP lease" button
Choose System Preferences from the Apple menu.
Choose Network from the View menu.
Select Wi-Fi, then click the Advanced button in the lower-left hand corner of the screen.
Click the TCP/IP tab from the top of the screen.
Click the "Renew DHCP lease" button.
Select the Wi-Fi tab and view your Preferred Networks list.
Select each network and click the minus sign to remove those networks from your Preferred Networks list.
Click OK and close the Network preferences.
Remove your stored network passwords using the Keychain Access Utility.
Open Keychain Access from /Applications/Utilities. Your window will look like this:
Remove your AirPort network passwords from the login keychain: Select the "login" keychain from the Keychain sidebar. Click the "Kind" column to order the list of keychain items by their type. Remove all entries of the kind: "AirPort network password".
Remove your AirPort network passwords from the System keychain: Select the "System" keychain from the Keychain sidebar. Click the "Kind" column to order the list of keychain items by their type. Remove all entries of the kind: "AirPort network password".  Note: The above steps will remove your Wi-Fi network passwords. If you do not know them, or if your network does not use passwords to restrict access, you should contact your network administrator.
Restart your computer.
Join your Wi-Fi network. You will need to enter your password for your network again if it requires one.
Regards,
-Norm G.

HP Photosmart 7520 does not recognize computer when trying to scan.

I have went thru the wireless setup on the printer, have done the steps recommended for other similair posts, printer will scan when initiated by paint, but does not find computer when accessing from printer screen. Computer and printer are connected and wireless network test results are all good. I've run out of ideas. Please help.

I have the same problem on my photosmart 5510dB111
i cannot print any of my apps when i initiate the process
they print all right fom hp. i have crossword puzzles printed everyday at the time they are scherduled.Sa
Sansal 5

Documents pending does not printing while printing through network

Hi!
Every Body! i've a problem my printer does not printing copu when i tried to print a copy using network.
When i tried to print through USB Cable it work well.
I dont understand how this problem can be resolved.
Kindly Help me.
Printer Model : HP LaserJet M1120n MFP
This question was solved.
View Solution.

Hi,
Looks like the printer is not on the network or the ip address may have changed
Please download and run the HP print scan doctor, it will identify and fix the issue...
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Im-120773-1&cc=us&dlc=en&lc=en...
or you may have to reconfigure the printer back to the network and install the printer drivers back on the computer...
Although I am an HP employee, I am speaking for myself and not for HP.
*Say thanks by clicking the "Kudos! Star" which is on the left*
Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue.
Although I am an HP employee, I am speaking for myself and not for HP.
*Say thanks by clicking the "Kudos! Star" which is on the left*
Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue.

Airdisk does not show up on my network

I have used an Airport extreme to create a home network. I have connected my laptop to the network via the ethernet connection and my media player is wiressly connected to the network. Network is working fine and both media player and laptop can see each other. However I have a USB hard disk connected to the airport express which does not show up on the network. However the USB hard disk does show up/recognised in the airport utility . Help!!

I'm also trying to connect a network hard drive to my new Airport Extreme (that's why I bought it) in a PC network of up to 6 connections. The network is fine, no problems, but the hard drive is invisible. I have formatted the drive as exFAT, as none of my computers have a FAT32 format option, only NTFS and exFAT.
The disk shows up on the AE, but only as its default identity, not the labeled volume. And, when I try to Map Network Drive, using 10.0.1.1 (I'm not even sure this is the right address, REALLY tough to find in the Help) for the AE and the volume label, per the Vista Map Network Drive utility, nothing.
I may have to return the AE to the dealer. That would be a shame.
Any suggestions?
Thanks

Iphone 4 does not stay connected to my network

Since upgrading to 6.1, my iPhone 4 does not stay connected to my network. I have to input my password each time I leave my house. My other devices stay connected, so the issue is with the upgrade. Has anyone found a way to keep their IPhone connected to their network? Thanks.

I don't have another phone to try. I took out the sim to check for deffects but it looked fine. Cleaned the sim card with alcohol and cleaned the aim compartment. Phone didn't loose Internet connection all day yesterday, but this morning went to check emails and wouldn't update until I turned airplane mode on then off again.

A june 2012 icloud backup shows up on my icloud storage manage list, but does not show up when i try to restore from icloud backup. what to do?

Question repeated: A june 2012 icloud backup shows up on my icloud storage manage list, but does not show up when i try to restore from icloud backup. what to do?
I want to restore from my june 2012 backup because it contains pictures that i lost when my phone broke in september. if anyone could help that would be awesome. thanks

Did you tap "Show older backups" on the Choose Backup screen (see image below)?

I have just downloaded a free app and there is no icon and it will not open from the list even tho it appears to have downloaded and the "open" button is available. Does not show up when I search for it. Plenty of memory . . .

I Have an iPad mini running iOS 7.1.2, I downloaded a new app and it's icon does not appear anywhere ( have ~ 180 apps so not at limit) and it won't open from the purchased apps list. It does not show up when I search for it so can't open t that way either. It doesn't require iOS 8. Can't delete and reinstall, cause not icon. This is not a normal "app won't open" question. it doesn't start the. Stop it just doesn't seem to exist. Any help is appreciated

Hello Chelleuri,
Thank you for using Apple Support Communities.
The following article provides information to trroublehshoot issues with installed apps, including not opening.
iOS: An app you installed unexpectedly quits, stops responding, or won’t open - Apple Support
Regards,
Jeff D.

My iPad does not have sound when on the Internet, including YouTube, but does have sound with iTunes and other apps. How can I correct this?

My iPad does not have sound when on the Internet, including YouTube, but does have sound with iTunes and other apps. How can I correct this?

If you are sure that you have sound in other apps - and if you can still hear keyboard clicks and get notifications, then system sounds are not muted. Try this and see if it works.
Close all apps completely and reboot the iPad.
Go to the home screen first by tapping the home button. Double tap the home button and the recents tray will appear with all of your recent apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

After installing Mountain Lion, iMessages and Facetime does not work. When I try to sign-in I get a message that says: The server encountered an error processing registration. Please try again later. Apple care does not know what is the cause. Please help

After installing Mountain Lion, iMessages and Facetime does not work. When I try to sign-in I get a message that says: The server encountered an error processing registration. Please try again later. After 4 calls to apple and 8 and a half hours on the phone. The apple people does not how to solve the problem. The last thing they told me is that they will send the problem to their engineers and I will hear from them. unfortunately they have not contact me.
During the phone calls I tried putting the date and time in automatic, changing the username and password, I even tried using somebody elses username and password. Please help, facetime is my tool to telecomute, and it is hurting my job.

I had the same problem and found the solution here:
https://discussions.apple.com/thread/3189272

"Connect to iTunes to Use Push Notifications" comes almost in every app that I open and it does not notify me when I got message in Whatsapp and Viber. Please help me to overcome it, it is becoming quite annoying!

"Connect to iTunes to Use Push Notifications" comes almost in every app that I open and it does not notify me when I got message in Whatsapp and Viber. Please help me to overcome it, it is becoming quite annoying!

Did you get any help on this? From what I can see from surfing this site, it's a BUG that no one has offered a solution to. It sometimes happens after a 'reset' and going to ITunes does not offer a way to 'set up push notifications'.

WRE54G does not recongize WRT100 when WRT100 network mode is set to Mixed

Similar Messages

Maybe you are looking for