WRE54G expander and D-LINK 624 router

Note: DI-624 has 4 lines ethernet wired connectors and 1 wireless antena.
With WRE54G powered and ethernet connected to the router line 2, the CD used to setup the expander did not worked at first time and resulted in a message in the computer: The WRE54G can not associated this AP in repeater mode. The next step was to change the configuration of DI-624 by accessing the IP address of the router (Web page of D-link). I put security desable and applied the new configuration to the router but loss the wired (line 1) connection to the internet by DI-624. I reboot the computer and internet came back. I started again with CD setup and the message desappeared but the red light still ON even with the message congratulations in my screen for Linksys setup. When I disconnected the ethernet cable to the expander and after few seconds, for my surprise the both leds went to blue light. When I returned to secure mode in the router, the expander return to red light. Then I decided to run setup with WPA enable until final with congratulations in my screen of Linksys setup wizard but with red light on the expander. After removing the ethernet cable, then after few seconds the Expander turn both leds to blue color. I sent this mail by a computer in the lower floor using this WRE54G expander.

Well is your D-Link router supports WDS (wireless distribution system), if yes… WRE54G may work with this router…

Similar Messages

WRE54G Rev 1 -- D-Link 524 Router

Hi,
I have a Wireless D-Link 524 Router (newest firmware) and I am trying to expand the range of my network using a LinkSys WRE54G Rev. 1 expander.
First off will the WRE54G work with a D-Link router? On the box it says will work with "most" wireless routers. But then on a page in the documentation it lists only 3 Linksys routers.
When setting up the D-Link router with DHCP. It allows you only to use the IP Range of 192.168.0.xxx the default setting for the WRE54G is 192.168.1.240. I changed it to 192.168.0.240. Same channel. There is also no security setup on either devices. But still no luck.
Has anyone else had any luck using the WRE54G with a non Linksys product?
If you need anymore info let me know.
Thanks

As you mentioned ..... you changed the Ip settings on Range Extender from 192.168.1.240 to 192.168.0.240 ... subnet - 255.255.255.0 ...& gateway address 192.168.0.1....
Check the light status ...
Also check the wireless settings are same as in the router .....
Try to ping the address of the Range extender .... see if it works ....

BT Softphone and D-Link 2740B router problem

Has anyone managed to work out how to set up a D-Link 2740B router so that BT Softphone will work?
The best help I can get from BT INDIA is change the baud to 5060, what ever that means?
I am not a techie, so any help in a simple step by step fashion would be most welcome.
Solved!
Go to Solution.

no thats no what i thinking about... i dont want to connect any devices as handsets ect to my laptop, laptop must be free as is now if this router have VOIP in the lastest firmware i think i can connect router to my bt broadband line then standard handset to the router and thats it. From the router level set the voip softphone internet telephony connection for this handset and thats it.... then if I will need another standard landline handset then simply connect it straight to the bt line... thats my vision....no devices connected to my computer its not working that way
If you already have bt home hub its working away from your computer so only one reason to change router is to do it in the same way as BT.... as BT have rubbish routers and with more than one laptop in the home network just cut the connecton this making me mad.....

Expand and collapse link in jsf datatable

Hello all,
Initially i am displaying 5 rows per page. when user clicks expand link the table should display all the records in the page.when collapse is clicked vice versa
Thanks
K Ramu

Hi Balu,
Sorry for that, here is my code snippet. the problem i am getting is if i click the expand link it is expanding bids for all the projects, i want the expand feature for a selected project only. please help me where did i mistake.
          <t:dataTable id="openForBidsTable" rowIndexVar="row"
               value="#{OpenForBidsBean.openForBids}" var="projects" border="1"
               cellpadding="1" cellspacing="1" first="0" rows="5">
                    <t:outputText value="#{projects.nameOfTheProject}" />
               </t:column>
               <t:column>
                    <t:outputText value="#{projects.description}" />
               </t:column>
               <t:column>
                    <tr>
                         <td colspan="12"><h:panelGrid
                              binding="#{OpenForBidsBean.gridPanel1}" rendered="true">
                              <t:dataTable id="BidTable" value="#{projects.bids}" var="bids"
                                   border="2" cellpadding="2" cellspacing="2" first="0" rows="5">
                                   <t:column>
                                        <t:outputText value="#{bids.vendors.userName}" />
                                   </t:column>
                                   <t:column>
                                        <t:outputText value="Title" />
                                   </t:column>
                                   <t:column>
                                        <t:outputText value="Notes" />
                                   </t:column>
                              </t:dataTable>
                              <h:commandLink action="#{OpenForBidsBean.expandProjects}"
                                   value="Expand Link" />
                         </h:panelGrid> <h:panelGrid binding="#{OpenForBidsBean.gridPanel2}"
                              rendered="false">
                              <t:dataTable id="BidTable1" value="#{projects.bids}" var="bids"
                                   border="1" cellpadding="1" cellspacing="1" first="0">
                                   <t:column>
                                        <t:outputText value="#{bids.vendors.userName}" />
                                   </t:column>
                              </t:dataTable>
                              <h:commandLink action="#{OpenForBidsBean.collapseProjects}"
                                   value="Collapse Link" >
                              </h:commandLink>
                         </h:panelGrid></td>
                    </tr>
               </t:column>
          </t:dataTable>
managed bean code:
public HtmlPanelGrid getGridPanel1() {
          return gridPanel1;
     public void setGridPanel1(HtmlPanelGrid gridPanel1) {
          this.gridPanel1 = gridPanel1;
     public HtmlPanelGrid getGridPanel2() {
          return gridPanel2;
     public void setGridPanel2(HtmlPanelGrid gridPanel2) {
          this.gridPanel2 = gridPanel2;
public String expandProjects() {
          getGridPanel1().setRendered(false);
          getGridPanel2().setRendered(true);
          return "selected";
public String collapseProjects() {
          getGridPanel1().setRendered(true);
          getGridPanel2().setRendered(false);
          return "selected";
Thanks
KRamu

WRT54G3G-ST ROUTER will it work with WRE54G EXPANDER

Does anyone know if the WRT54G3G-ST ROUTER with a sprint card will it work with WRE54G EXPANDER, and if so how do you get it set up.
Thanks

Hmm not sure if WRE54G will work with WRT54G3G-ST.
Click Here and you will fine the Compatibility Comparison Chart for WRE54G v3.

Setup problems with the WRE54G Expander

My router is the WRK54G and its hooked up to my PC on the main floor family room. My notebook (Wireless card: Intel Proset/Wireless 3945ABG) is on the 2nd floor. I set up the expander and the link is blue showing a successful connection. The problem I am having is the signal strength is still very poor (-88dBm) I have moved the expander to different location in my house and the signal is still poor. I tried setting up the expander with the setup wizard software and the network setting cannot detect my wireless card. What can I do to get a better signal on the second floor.

Hi,
I am also using an Intel ProSet driver, Sony Vaio laptop, and have no trouble connecting.
Try starting up your Intel ProSet utility and check you have the following:
General Tab:
Network Name (SSID): (should match your network SSID)
Profile Name: (whatever, I use my SSID)
Mode: Infrastructure (AP)
Security: WEP (if your Router has security set on)
Speed: 54 MBPS
Band 802.11g
Channel: 6 (or whatever channel your routher is on)
802.1x Protocol: Disabled
Hardware radio switch: On
Switch radio - On
Networks Tab: A list of available networks should appear. If not, hit the Scan button and pick your network. Make sure your SSID shows up under Network name column and that there is a little radio beacon in the far lefthand column indicating you are associated with the correct router/AP (I have between 4 and 6 neighbors APs show up). You may need to go into your router setup to enable SSID broadcast for trouble shooting if you have turned it off (or you may not be able to "see" you are connecting to the correct Router).
Under Networks Tab, Advanced Settings: Connection Preferences should be set to Connect to ad hoc networks (first or third choices should work). Wireless mode selection should be set to "Connect to both 802.11g and 802.11b". 11b/11g mixed protocol should be set to "CTS to self enabled". Both boxes under Advanced security should be checked.
Back out to the Networks tab screen that lists the available networks and Double Click the SSID of your network. A screen should popup labeled Profile Wizard. In the Profile Wizard dialog box there are 4 tabs. Under the General Tab check that the SSID is correct and under Operating mode, the Infrastructure button should be selected. Uncheck Enable Cisco Extensions. Under Security Tab: Network Authentication should be Open, Data Encryption should be WEP (if you are using WEP), under Encryption Key settings: Check "Set Manual Key", confirm Encryption level matches your Router (128 bit on mine), check your Hex Key is correct (reenter or cut/paste from your Router setup utility), uncheck "802.1x Enabled"; Under Advanced Tab: all but last should be unchecked (only check is on "This profile can be used by all users").
Adapter Tab: Doesn't matter
If that's all OK, go into the Range Extender Web utility (192.168.1.240), make sure the Mode is set to Mixed, SSID matches your Router and Laptop SSID including the case (for example, use all upper case letters), Channel is set to the same number as Router and Laptop, Security is Enabled if on on your Router and Laptop, go into "Edit Security Settings" button and check that Security Mode is set to WEP, Default Transmit Key is correct (use 1), WEP Encrypption is same (mine is 128), and that the Key Hexadecimal numbers are same as on your Laptop and Router and that the same Key is being used on all (ie Key 1). Note that if you generated the Keys from a passphrase, the keys will be differ if the capitalization of the passphrase differed between your Router, Laptop, and Range Expander.
If all this is OK and seems to match, I would temporarily disable security on the Router, Laptop and Range Extender and retry. Hope that helps

Using D-Link DI-624 Router for "G" Wireless Purposes

I want to use an old D-link router in another part of the house to provide wireless "G" connectivity to my older devices, so I can use 5 GHz band for "N" connectivity exclusively via my Airport Extreme (Older version, not Gigabit).
I go upstairs, plug the D-Links WAN port to the jack that connects to one of the Airport Extreme's LAN ports downstairs. I shut off dhcp server on the D-Link. I turn on the D-link's wireless capability (unencrypted for now, just for testing).
When I plug a computer in to one of the LAN jacks of the D-Link, I have full connectivity to the internet. And I see the wireless signal from the D-Link which has a unique SSID. Unfortunately, while I can connect to the D-Link wirelessly, I cannot get to the internet.
I'm sure I have something configured wrong.
Questions:
1. I have the Airport Extreme set to hand out ip addresses in the 10. range. Should I set up the D-Link router to get a static IP address from the Airport Extreme? How do I do that. Some sites suggest a 10 series IP address, but outside the range of the DHCP addresses that the Airport Extreme usually hands out.
2. Any ideas on configuring the DI-624? I've shut off DHCP server (everyone says to do that). But Are there any other settings?
3. Some tech help sites suggest not using the WAN Port at all on the D-link, but rather, connect to one of the LAN ports. Does this make any sense? Going from one of the LAN ports on the Airport Extreme to one of the D-Link's LAN ports.
4. Once I get the wireless G network running, I'll fix the encryption.
I think that in order to answer this question you'll need some first hand knowledge of the DI-624. Unfortunately, the DI-624 is now a discontinued product and there is little information available on D-link's web site.
Thanks in advance for any advice.
kenny

If a Mac plugged into a LAN port on the D-Link gets internet access, the AirPort Extreme base station (AEBS) and D-Link are both configured properly.
The wireless side of the D-Link should also be acting properly since LAN access is working.
The most likely problem is that your Mac has incorrect DNS information in the System Preferences->Network preference pane->AirPort area.

VPN and D-Link DI-624

How do i set up my D-Link DI-624 router with VPN.
What do i use for my server address and were can i find the server address.

Please explain your setup and what you want to do better.
You have OS X server?

Airport Express with D-link 624+ wireless router.

Have got a D-link wireless router connected. Wireless internet works fine on its own, but I cannot connect the apple airport express to the wireless internet, so I have to keep switching connections and am unable to use the internet at the same time as streming music to my stereo....what am I doing wrong?
please help me. I thought I knew computer gear, but was SOOOO wrong.

I had a DL 624+ (and have since abandoned it). I had a lot of instability problems with it, which seemed to be related to the Dlink DHCP implementation. I was watching the log on the router, and I was seeing the dlink constantly re-issuing DHCP addresses to the macs on the network - it would renew the addresses twice a minute.
I had seen some posts which suggested that there were problems with either long DHPC client names, or client names which had non-alphanumeric characters in them. (Note if your machine name has spaces, this could happen.)
So, you might want to try:
-Assigning static IP addresses and see if the problem goes away
-checking your DHCP client names to make sure they are between 8-12 characters
Hope this helps!

Adding a link to expand and collapse all DHTML drop downs

Hi, can anyone help me adapt the "Skinny on Skins" example "Add a Toolbar button to expand and collapse all DHTML drop downs" so that it will work with just a simple HTML link in RH8, instead of being attached to a custom skin button?
The example looks like this:
Step 1. Open the Skins Editor for the skin where you want to add the button.
Step 2. After the preview loads into the window, ensure that the Toolbar tab has focus, then click the plus symbol. The Custom Toolbar Item dialog should display.
Step 3. Type the Item Name (This is simply an internal reference for the button).
Step 4. Type the Text (This is the text that will be seen by the end user. The field must contain something. So if you don't want any verbiage to display for your toolbar item, simply type a space.)
Step 5. Choose your Image Options, then click the Action tab.
Step 6. Click the JavaScript option button.
Step 7. Enter the following code in the OnClick field:
javascript:toggle()
Step 8. In the JavaScript area, ensure the Inline JavaScript option button is selected, then click the edit (Pencil) icon located to the right.
Step 9. Enter the following code in the Inline JavaScript dialog
var show = "false";
function toggle() {
parent.frames[1].bsscright.focus();
var arrayofDivs = parent.frames[1].bsscright.document.all.tags('DIV');
if (show == "false") {
for (x=0;x<arrayofDivs.length;x++) { arrayofDivs[x].style.display = "block";}
show = "true";}
else {
for (x=0;x<arrayofDivs.length;x++) { arrayofDivs[x].style.display = "none"; }
show = "false"; }
Step 10. Click the OK button to close the Inline JavaScript dialog.
Step 11. Click the OK button to close the Custom Toolbar Item dialog.
Step 12. Click the OK button to close the Skin Editor.
Step 13. Generate WebHelp via File > Generate > WebHelp and ensure that you have the new button selected with a check mark. This will probably require stepping through some screens to see the place where you can select it.
Many thanks
Jonathan

Hi again
I want to use it in the header of one of my Master Pages, so it will only be created/maintained once. Not all my pages have drop downs in so rather than have a toolbar button available for every page, I was trying to be a bit cuter by having two Master Pages - one for normal pages and one for pages with drop downs in.
I'm no javascript expert so I'll see if one of my developers can help.
Thanks anyway
Jonathan

Wi-fi bridge between two routers TP-LINK WR841ND (WDS). HP 1536 dnf MFP connect to one of this routers (copper). My Ipad or Iphone can't find HP 1536 dnf MFP (using Eprint). Ipad and iphone connect to router across WiFi.

Hello.
I have wi-fi bridge between two routers TP-LINK WR841ND.
The name of this technology - WDS.
HP Laser JET 1536 dnf MFP connect to one of this routers (copper).
Second device (my NETBOOK) connect to second router (WiFi).
I have good communication between NETBOOK and HP Laser JET 1536 dnf MFP via WiFI-bridge.
In usual case NETBOOK can find (and can Ping) network printer and make a print some files.
But my Ipad or Iphone can't find HP Laser JET 1536 dnf MFP (using Eprint). Ipad and iphone connect
to router across WiFi.
Please, help!

Are you using the ePrint Mobile App, the ePrint Printer Control App, or just trying to send an email to the printer's ePrint email address?
Does AirPrint work?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

How to perform expand and collapse operation on click of link or button

Hi
Is there anyway by which i can perform expand and collapse operation over a table on click of a command link or button without using show details component.
Is there any other alternative to show detail.
I do not want to use show detail because of the following reason.
I have got a page where in i pass some parameters to the URL based on which details get displayed on the page.
Now when i pass a parameter, change the parameter, once again send the previously used parameter(i,e the parameter that i passed initially), values in the table under show detail do not show any change in values.
Once i pass values which i have already passed, values in the table under show detail component do not refreshed.
If anyone has encountered with similar situation, then please post me reply's as to how you could over come the problem??

Hi
Perhaps you could use an on-demand application process instead - you can specify these in the URL.
The URL syntax (for your link) would be like...
f?p=application_id:page_id:session:APPLICATION_PROCESS=process_idIs this what you mean?
Cheers
Ben

Any speed difference between Apple Wifi Router(air express) and Tp link(or others) wifi router)

Any speed difference between Apple Wifi Router(air express) and Tp link(or others) wifi router?
I'm using a tp link router and sometimes it takes a long time delay for my 2 mac computers to connect each other. I don't know this is because of the router compability or the computers.

Anyone knows?

Wireless connection between D-Link WiFi router and Time capsule stopped working

We have an ISP provided D-Link wireless router (DIR-615) to which we wirelessly connected our 2Tb Time Capsule for back up and to connect a USB printer to out network. This worked perfectly for 3 1/2 years, until about a month ago, when the time capsule suddenly decided to go "off line". ie we could no longer access it or the printer via our wireless network. We had changed nothing - just one day it stopped working.
We tried to get it back online with no success. As the 2Tb Time Capsule was almost 7 years old and had had some HDD issues in the passed, we figured it had got old and died and that it was time to replace it; so we bought a new 3Tb Time Capsule, thinking this would get everything back to normal.
However much as we tried, we were also unable to get the new 3Tb Time Capsule to connect wirelessly to the D-Link wireless router. The Airport Utility did not show the D-Link wireless router or its wireless network, although we were (and are) able to see it in Systems Preferences>Networks from all our multiple devises. This in itself seemed odd. No matter what we tried, the Airport Utility would not find the D-Link wireless router and hence we could not add the 3Tb Time Capsule to the existing wireless network.
At the end of the day we got fed up with trying to add the 3Tb Time Capsule to the D-Link wireless network, and connected it via a LAN cable to the D-Link router instead. We then set it up as its own network. Worked gerat. Having done that we thought maybe the old 2Tb Time Capsule might not have been the problem after all, so we tried extending our new 3Tb Time Capsule wireless network using the 2Tb Time Capsule wirelessly. This worked perfectly! And we are now almost back to what we wanted.
So although we have a work around, this means now have 2 separate wireless networks as opposed to the original single wireless network where everything talked to everything else.
Can anyone shed any light on any of the following:-
1. Why the original wireless network connection between the D-Link router and the 2Tb Time Capsule just stopped working? Was there some software change from Apple that "decided" D-Link wireless routers were no longer secure; and therefore the TCs could no longer connect to them?
2. Why it was not possible to extend the existing D-Link wireless network using the the new 3Tb Time Capsule?
3. Is there is anyway that we can get back to a single wireless network based around the D-Link wireless router as the primary router connecting to the modem, where the 2 Time Capsules connect as "wireless satellite base stations"?

1. Why the original wireless network connection between the D-Link router and the 2Tb Time Capsule just stopped working? Was there some software change from Apple that "decided" D-Link wireless routers were no longer secure; and therefore the TCs could no longer connect to them?
A firmware update to the TC came along and you agreed to it without perhaps even noticing.. it then smashed your setup because Apple do not recommend the setup you were using and it is very poor.
2. Why it was not possible to extend the existing D-Link wireless network using the the new 3Tb Time Capsule?
Because it is such a poor setup that Apple have taken away your ability to choose it unless you know exactly what you are doing.
3. Is there is anyway that we can get back to a single wireless network based around the D-Link wireless router as the primary router connecting to the modem, where the 2 Time Capsules connect as "wireless satellite base stations"?
Yes, this I can help you with.
I have several ways around the problem.. but the first one is.. why use the DIR-615 at all.. it is not a modem.. it is a very ordinary bottom end, poor single band slow wireless router.
Why don't you simply remove the DIR-615 from the network completely.. plug whatever it is the ISP supplies you.. an ethernet connection from whatever that modem is you mentioned into the WAN port of the Time Capsule. And use the TC in some router mode.. same as the DIR-615 was setup.. dhcp or pppoe or whatever.. I doubt the TC cannot match it.
If you have issues please post a few screenshots from the DIR-615 to show how it is setup from the WAN side.. and as long as you are given the username and password or whatever the ISP uses to authenticate then chuck out the DIR-615.
Tell me if that is a goer.. if not we can work out a few other methods..
eg. Simply turn off the wireless in the DIR-615. It is poor cf the TC and there is no need for it.. with the TC in bridge only use the TC for wireless as well as wireless extend with your old TC.
Or setup roaming network where everything uses the same SSID.
Then you will have one wireless network. And it won't matter what as long as it connects.. although IMHO this is not right as the TC is such a superior router now you are wasting your new TC.

Our Century Link Modem/Router supplied at set up, has poor range. It is in the kitchen ( main level ) and won't reach our studio fully at 30-40ft away. Will setting up my time capsule i the studio improve this signal?

Our Century Link Modem/Router supplied at set up, has poor range. It is in the kitchen ( main level ) and won't reach our studio fully at 30-40ft away. Will setting up my time capsule in the studio improve this signal? If not, what can I do!???

Will setting up my time capsule in the studio improve this signal?
Yes, if the Time Capsule remains connected to your Century Link modem/router using a permanent, wired Ethernet cable connection.
Any other option will involve the purchase of more hardware.
One option would be to keep the Time Capsule connected to the modem/router using a short Ethernet cable, and configure the Time Capsule to provide a wireless network. Add an AirPort Express about half way between the kitchen and the studio to wirelessly extend the signal from the Time Capsule to provide a much stronger signal in the studio.
Another option might be to use a wireless repeater that is compatible with the modem/router. Century Link might have a solution, or be able to recommend a compatible device for that purpose.

WRE54G expander and D-LINK 624 router

Similar Messages

Maybe you are looking for