Write community in pix501

Hi,
I need to configure write community in pix501. I tried , but the option is not available.
I configured the read community using the following command
snmp-server community public
But there is no option for write community.
Sarav

Hi,
SNMP write isn't supported on pix.
HTH
Andrew.

Similar Messages

Cisco Works SNMP write community string Incorrect

Hi,
I have installed Cisco Works at my organisation. Under RME -> Inventory -> Import status -> Device Attribute Error: I am getting: Incorrect SNMP write community strings. Even though i know perfectly well the SNMP write community string is correct. To prove that, if I delete the device and then add the same device using the same SNMP write community string it works fine. then a couple of days later, it comes up with the same message "SNMP write community string is incorrect". I have increased the time and retries for the SNMP settings at the ANI server, still it has not resolved the issue.
Please help

I have sharched the CCO bug toolkit and according them, it was a know issue for verion 3.4 but it has been fixed for Ver RME 3.5. But we are currently running RME 3.5, therefore it does not make any sense.

MDB stops while trying to write to a Cache

Hi,
I have this MDB that listens to a JMS queue, and I want to write to a Tangosol (Coherence) cache from this MDB. But even when i just have
NamedCache cache = CacheFactory.getCache("xyz");
inside the MDB, I get an exception which looks like this :
2008-01-04 11:44:45.187 WARNING J2EE EJB-02014 [WebCenterMDBDeployer:WebCenterMDBDeployer:WebCenterMDBBean] All message consumer threads have terminated due to provider errors, stopping MDB.
oracle.classloader.util.AnnotatedNoClassDefFoundError:
     Missing class: com.tangosol.net.CacheFactory
     Dependent class: webcentermdbproject.WebCenterMDBBean
     Loader: WebCenterMDBDeployer.root:0.0.0
     Code-Source: /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/WebCenterMDBDeployer/WebCenterMDBDeployer.jar
     Configuration: <ejb> in D:\Jdeveloper10.1.3.3\jdev\extensions\oracle.adfp.seededoc4j.10.1.3\j2ee\home\applications\WebCenterMDBDeployer
The missing class is available from the following locations:
     1. Code-Source: /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TestPortlets10/TestPortlets10/WEB-INF/lib/tangosol.jar (from manifest of /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TestPortlets10/TestPortlets10/WEB-INF/lib/coherence.jar)
     This code-source is available in loader TestPortlets10.web.TestPortlets10:0.0.0.
     2. Code-Source: /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TestPortlets/TestPortlets/WEB-INF/lib/tangosol.jar (from manifest of /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TestPortlets/TestPortlets/WEB-INF/lib/coherence.jar)
     This code-source is available in loader TestPortlets.web.TestPortlets:0.0.0.
     3. Code-Source: /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TangosolTest1/TangosolTest1/WEB-INF/lib/tangosol.jar (from manifest of /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TangosolTest1/TangosolTest1/WEB-INF/lib/coherence.jar)
     This code-source is available in loader TangosolTest1.web.TangosolTest1:0.0.0.
     4. Code-Source: /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TestPortlets14/TestPortlets14/WEB-INF/lib/tangosol.jar (from manifest of /D:/Jdeveloper10.1.3.3/jdev/extensions/oracle.adfp.seededoc4j.10.1.3/j2ee/home/applications/TestPortlets14/TestPortlets14/WEB-INF/lib/coherence.jar)
I am just trying to get the Cache, and still getting this exception.. Its the same when i try to put something to the cache..
Any idea what might be going wrong? After this, the MDB stops working altogether..
Thanks in advance
Pravin

Hi
I would recommend checking your system.log file for an error of this type. Probably just filter with SAM.
"timestamp" kernel SAM Multimedia: READ or WRITE failed, SENSE_KEY = 0x02, ASC = 0x04, ASCQ = 0x01
If you are seeing errors of this type, my guess is that you're having write communication errors when attempting to burn. I can't guarantee that these errors specifically indicate a hardware failure, but my experience has been when these errors are produced, an ODD drive or cable failure is causing a bus error due to input/output errors with the data.
If you go to Applications -> Utilities -> Console, you can bring up the system.log file. If the drive is bad, I hope you can find a replacement option.

Question on SNMP Read-Write String ...

Hi,
My question is that if I am using an SNMP read-write community string on the device, would Prime LMS still require
the logging credentials of the device via ie) telnet/ssh ?
The reason how I undertand this as long as the SNMP manager (Prime LMS) and the agent (end device) have the same read-write community,
couldn't the Prime LMS just write to the device without the standard logging credentials ? or is the logging credential of the device is a must for it
to push configuration to the device ?
Pls advise.
Many thanks.
Cheers,
- sn -

Even though the SNMP communication is there between device and LMS, it is not possible to configure any device using SNMP, except for the RW variable and OIDs, which are limited in their scope.
It is not possible to configure, but to copy configuration to or from device using SNMP. See the following document to check further:
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_configuration_example09186a0080094aa6.shtml
Many people use this manual process to copy configuration from device using SNMP, edit it and copy back to device to make configuration changes, but ideally no NMS server does it and LMS is no exception.
It uses transport Layer protocols like telnet/ssh to communicate with device like a normal user to configure commands, which in this case is done by Netconfig job.
For more details see :
http://www.cisco.com/en/US/products/sw/cscowork/ps2073/products_tech_note09186a00800a6974.shtml
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_resource_manager_essentials/4.3/user/guide/netcfg.html#wp1070214
-Thanks
Vinod Arya

Javacomm read/write problem

Hello all, i have successfully installed javacomm package in my computer and i can enumerate all available ports. My problem is between the read - write communication. By running the SimpleRead first and then the SimpleWrite i got a "Port Already in use" which sounds normal to me, so i connected 2 pc's with a serial cable and runned one of sun's samples on each.
Step 1. SimpleRead waits for data on COM1
Step 2. SimpleWrite(on other pc) sends some data from COM1
Both COM1's are connected with that serial cable but seems no data coming. Am i doing something wrong? I tried same thing with VirtualPC but still no data arriving.
Any help appreciated. Thanks

Hello all, i have successfully installed javacomm
package in my computer and i can enumerate all
available ports. My problem is between the read -
write communication. By running the SimpleRead first
and then the SimpleWrite i got a "Port Already in
use" which sounds normal to me, so i connected 2 pc's
with a serial cable and runned one of sun's samplesAre you using a terminal the opens the port?
Without any ambiguity whatsoever,
"Port Already in use" means
something else has already opened the com port and I can say the
COMM API. works because I use it all the time with GPRS board.
ie:
https://hyperview.dev.java.net/source/browse/hyperview/www/comm/SerialHandler.java?rev=1.2&view=markup
Crossing pins 2 & 3 will only redirect your output/input
but will not cause the the port to be in use Jos.
(T)

Adapter specific message attributes in ABAP proxy

Dear all,
i have a short question. I have a file to ABAP server proxy scenario. When picking up the file i write communication data from the adapter in the message header using dynamic configuration and route the message to a abap proxy.
My question is: Do i have access to the header data in the proxy, or do I have to make a message mapping and put the header data into the payload of the message?
Kind regards
Florian

Hi,
here is a blog about your scenario:
File to R/3 via ABAP Proxy
Hope it helps.
Regards
Patrick

Does anyone know what the "Provision Failure: MEDIATION-5, Lrad! errors are in WCS

Does anyone know what the "Provision Failure: MEDIATION-5, Lrad! errors are in WCS?
I get this when pushing an AP template to six new 3502i series access points. The error reads like this:
*** Apply Result for AP 'NameOfAPhere(C0:FF:EE:C0:F:EE)' ***
**AP Parameters**
Provision Failure: MEDIATION-5, Lrad!C0:FF:EE:C0:F:EE,secondaryMwar,No access
MAC address has been changes to protect the names of the innocent...
The rest of the template appears to push. The 802.11a/n and 802.11b/g/n parameters show "success".
Anyone have the magic decoder ring for what these messages are referring to so that I can go fix the issue?
Thanks in adavance!

Hi,
Two things :
1- Can you refresh configs from WLC to WCS and then give it a try ?
2- Is WCS using the right read-write community string for this WLC ?
(Since we see a "No Access" message in the error)
Thanks..Salil

Favoring FireWire interface over USB for external HDD

I have my iMac hooked up to an external HDD via both USB and FireWire 800 as it is triple-interfaced (USB, FW 400 & FW 800).
Lately, as I turn on the external HDD (pretty much always once the iMac is up & running), the HDD icon shows in the Finder with the USB symbol.
It requires me to eject the HDD in the Finder and then disconnect the USB cable for the iMac to detect the external HDD again but now through FireWire.
The reason I use both interfaces is to handle HDD read/write communication via FW whereas USB only as hub (the external HDD comes with 3 USB ports).
Is there anything I can do to make sure the primary interface is FireWire and not otherwise?
Thanks!

In a recent phone call with OWC's tech support I asked the same question. Answer was "Do not connect both interfaces at the same time". There is no way to arbitrate the connection the Mac will use, and strange things will happen.
If you think about it, there is no way to specify a preference in the Mac for what ports to connect with, so it does what it wants, not what you'd like.
I can only imaging what happens on Windows machines. I suspect corruption ahead

LMS Software Image Management - Telnet failure

Hi all,
I had a problem with Software Image Management for the upgrade of a switch.
It seems that at the end of the upgrade, CiscoWorks was unable to save the configuration with telnet.
Yet, telnet seems to be ok because CiscoWorks manages to connect to the switch at the beginning of the upgrade.
Updating config file during software upgrade processDevice running-config is modified but failed to save the running-config to startup-config.Cause: Could not detect SSH protocols running on the device
TELNET: Failed to establish TELNET connection to 10.1.3.4 -Cause: Authentication failed on device 3 times.
I sent attached the logs of the upgrade.
Thank you in advance.

Hello,
The job fails last night after timeout.
I have reschedule job this morning for 2 switchs :
2960 with telnet and ssh enabled
2960 with telnet enabled only
The device credentials verification job seems to be coherent :
Device Name
Read
Community
Read Write
Community
Telnet
Enable
by Telnet
SSH
Enable
by SSH
1.
switch04-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Failed to connect.
Did Not Try
1.
switch03-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
But the job fails again cause telnet authentication failed on device 3 times.
I do not understand why LMS does not use ssh if possible at the finish of the job? Why telnet authentication fails ?
Thanks in advance.

LMS 3.2 credentials/username question

I recently installed the trial version of LMS 3.2 on a single server (10.1.1.1). Now my head is spinning over what credentials i'm using vs authorization to modify a routers config vs device config. etc etc.
I've added a bunch of devices, but I cannot configure any devices via LMS.
I added a user called lmsuser to my routers/swiches.
I added the loggin 10.1.1.1 comment to my routers/switches.
I added read and write community ("readstring" and "writestring" strings to my routers/switches).
Question
1) I currently log into the portal using username: admin. Is this used anywhere other than getting into the portal?
2) I created a credential set called "firstset" with a user called lmsuser and readstring and writestring community strings. Do I need to do something to associate "firstset" with each device in the DCR?
3) When configuring RME credentials, do I use the the IP 10.1.1.1?
4) In cisco view I see views of my devices. When I right click on a switch interface and select "disable" I end up with an error message about not having permission to make the change. What secret handshake is required to make this happen?
I feel like I'm just not connecting the dots here. Thanks in advance.

1. No. These credentials are only used to access LMS applications (the portal, command line, etc.). They are not used to communicate with devices.
2. It depends on how you are adding devices to LMS. Each way (manual add, Discovery, import) allow you to choose a credential set, or use an automatic credential set. If you choose automatic, then a credential set will be applied to your devices based on the rules you have defined. Note: credential sets are only automatically applied when a device is added to DCR. You can choose to manually apply credential sets later, but if you modify a credential set after a device is added to DCR, those changes will not automatically be applied to your existing devices.
3. I don't understand. This is the IP of the LMS server. I'm not to sure what "RME credentials" you are referring, but I can't imagine where you would add 10.1.1.1 with any credentials.
4. You need an SNMP read-write credential (e.g. community string) configured for the device in DCR (i.e. under Common Services > Device and Credentials > Device Management).

LMS 3.2: RME failed archive with Nexus 5010

Hi,
LMS 3.2, RME 4.3.1, dev packages updated, Windows.
We would like to archive the configuration of the Nexus 5010 switches. Due to authentication with Radius based on tokens we're not able to use telnet/SSH and therefore we only can use SNMP WRite in combination with TFTP. But, this is not working at all. Other systems like 3750 works fine. Is there a difference between Catalysts IOS and nexus NXOS?
I searched the forum and found this:
https://supportforums.cisco.com/message/663481#663481
upgrade to LMS 2.6, archive config not working anymore
We ship and start a TFTP server by default on Windows. You must have an SNMP read-write community string configured on your devices, and entered in DCR for TFTP config fetches to work. Additionally, udp/69 must be open between device and server.
The easiest way to troubleshoot this kind of problem is to start a sniffer trace on the LMS server (using Device Center > Packet Capture). Filter on all traffic to one of the failing devices. Then, run a Sync Archive job for that same device. When it fails, the sniffer trace will indicate what the problem is
Regards
Ad Olsthoorn

Hi Lavramov,
Yes I'm quite sure, I installed the required packages acoording to the Nexus.RME431.v2-2.readme.pdf manual. the manual tell me to install the following (see also attachement).
To install the Cisco Nexus Series Package, you must install the following dependent packages:
- SharedDcmaSS.RME431.v2-2.zip
- SharedInventoryMDS.RME431.v1-5-1.zip
- SharedSwimMDS9000.RME431.v1-6-1.zip
- SharedNetshowSS.RME431.v1-1.zip
regards
Ad

IDoc Control Record and Status Record Code, where is it!!!

Hi,
Where can i see the code for generation of control record and status record of IDoc.
   Thanks in advance for your answers

hi ,
1.first create an segment with the fields u want tcode we31 relase it .
2. create an idoc and assign segment to it tcode we30.
3.crate a message type tcode we81
4.assign that message to idoc tcode we 82.
do the ale configarations .
now u can write the code in our sender system
*1.     Create parameters/select-options for input data. i.e., message type, logical system.
parameters : p_mestyp like edmsg-msgtyp default 'ZKKUMSG',
             p_logsys like tbdlst-logsys obligatory.
*2.     Create Data objects for control record, data record and database table.
data : c_segment like edidd-segnam value 'ZKKUSEG',        "Data record (IDoc)-Segment type
       c_idoctp like edidc-idoctp value 'ZKKUIDOC'.            "Control record (IDoc)-Basic type
data : begin of i_tab occurs 0,
          ZKSNO   like ZKSTD-ZKSNO,
          ZKSNAME like ZKSTD-ZKSNAME,
       end of i_tab.
data : w_itab like i_tab.
data : s_segment like ZKKUSEG.
data : i_edidd like edidd occurs 0 with header line.
data : i_control_record like edidc.
data : i_comm_idoc like edidc occurs 0 with header line.
*3.     Select the data from responding tables into internal table for a defined condition.
here you have take ur internal table
*select single zsno zsname from zkiran into corresponding fields of itab where zsno = p_sno.
*4.     create control record into internal table.
i_control_record-mestyp = p_mestyp.         "Message Type
i_control_record-idoctp = c_idoctp.         "Basic type
i_control_record-rcvprt = 'LS'.             "Partner Type of Receiver
i_control_record-rcvprn = p_logsys.         "Partner Number of Recipient
*5.     create data record into internal table.
*i_edidd-segnam =   c_segment.
loop at i_tab into w_itab.
s_segment-zksno    = w_itab-ZKSNO.                     "Application Data
s_segment-zksname = w_itab-ZKSNAME.
i_edidd-sdata     = s_segment.
i_edidd-segnam    = c_segment.
clear w_itab.
append i_edidd.
endloop.
*6.     Process ALE Service Layer using the function module MASTER_IDOC_DISTRIBUTE. It returns the corresponding IDoc No.s.
call function 'MASTER_IDOC_DISTRIBUTE'
exporting
    master_idoc_control            = i_control_record
tables
    communication_idoc_control     = i_comm_idoc
    master_idoc_data               = i_edidd
exceptions
    error_in_idoc_control          = 1
    error_writing_idoc_status      = 2
    error_in_idoc_data             = 3
    sending_logical_system_unknown = 4
    others                         = 5.
if sy-subrc <> 0.
message id sy-msgid type sy-msgty number sy-msgno
          with sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
endif.
*7.     Display Communication IDocs.
loop at i_comm_idoc.
write : / 'Communication IDoc No. is : ', i_comm_idoc-docnum.
endloop.
*8.     Commit Work.
commit work.
i hope this sample code help u .
thanks

WCS MSE Help

I’m trying to synchronize one of our switches with the WCS/MSE (Version 6 on the WCS). I’ve added it onto the WCS and the MSE says it synchronizes properly but when I go into the SERVICES/MOBILITY SERVICES and look at the switch it is just showing the IP address. It’s not showing any of the ports or any information at all on the switch. I have the RW snmp string for the switch. Any ideas?

Well that is a complex question but let's start with making sure that you meet the requirements for it to work:
http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/6_0admin.html#wpxref43135
Switch Port Trace
The Switch Port Trace page allows you to run a trace on detected rogue access points on the wire.
To correctly trace and contain rogue access points, you must correctly provide the following information.
•Reporting APs—A rogue access point has to be reported by one or more managed access points.
•AP CDP Neighbor—Access point CDP neighbor information is required to determine the seed switches.
•Switch IP address and SNMP credentials—All switches to be traced must have a management IP address and SNMP management enabled. You can add network address based entries instead of only adding individual switches. The correct write community string must be specified to enable/disable switch ports. For tracing, read community strings are sufficient.
•Switch port configuration—Trunking switch ports must be correctly configured. Switch port security must be turned off.
•Only Cisco Ethernet switches are supported.
•Switch VLAN settings must be properly configured.
•CDP protocol must be enabled on all switches.
•An Ethernet connection must exist between the rogue access point and the Cisco switch.
•You should have some traffic between rogue access points and the Ethernet switch.
•The rogue access point must be connected to a switch within the max hop limit. The default hop count is 2, and the maximum is 10.
•If SNMPv3 is chosen, use the context option and create one for each VLAN, in addition to the one for the main group (which is required for non-VLAN-based MIBs).
Follow these steps to specify options for switch port tracing.
Using switch port tracing:
http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/6_0ctrlcfg.html#wpmkr1083367
After you meet all requirements the logs are your best bet for determining why it is not working. They are usually pretty good at leading you to the problem.
You would go to Administration > Logging and uncheck Status Polling, Configuration, SNMP Mediation, MSE/Location Servers, XML
Mediation, Navigator, Reports and Database Administration and change the message level to TRACE and click submit. Go back and recreate the issue
and then go back to the logging area and download the logs.
If you get the logs right after the test it should be in the wcs-0-0.log file and you will want to go from the bottom up and search for something like "
Switch port tracing failed". Around there will be why it failed.

Premiere Pro Editor's thoughts on FCPX

I've just spent a week learning FCPX to see if it's a viable alternative to fill in Premiere Pro's gaps (for example, it's terrible Multicam interface).
After a week with FCPX, I've decided to stop a client project and start over in Premiere. From what I can tell FCPX isn't quite ready for prime time yet: i.e. no effect/transition presets, no proper interface for keyframing, buggy clip speed controls that work on some clips but not on others, Timeline workflow that's confusing as hell, etc.
However, there are several great features in FCPX that Premiere Pro users would definitely benefit from (Adobe, please take notice. Forum users, if you like any of these ideas, please send them to Adobe as feature requests, as I will too).
FINAL CUT PRO X FEATURES THAT ARE NEEDED IN PREMIERE PRO:
First and foremost, the ability to use keywords to sort and organize subclips. This is HUGE and probably the biggest thing missing in PP's workflow! In FCPX, you can assign 1 or more keywords to clip selections. Each keyword becomes the equivalent to a Bin in PP's Project window. An interview clip, for example, can quickly be marked with in/out points during live playback, and each clip selection can be sent to its own respective keyword 'bin(s)' for easy finding later on. Thus a long interview clip can be broken up into any number of subclips organized by terms such as 'soundbite', 'nod', 'smile', 'reaction shots', 'favorites', etc. And since up to 9 keywords can be assigned their own keyboard shortcuts (e.g. 1-9 on the number pad), assigning keywords and thus organizing subclips into logical 'bins' can even be done on the fly during playback! Lastly, the 'subclips' in FCPX are intelligent in the sense that you can still drag the in/out points out up to the original duration of the clip, unlike PP's unusable subclips that create hard in/out points that can't be reset. Adobe, PLEASE add intelligent ways to organize subclips into bins! This is still the biggest thing missing in Premiere IMO.
Easy way to export/import keyboard layout presets.
Graphical keyboard layout preset interface. i.e. ability to set shortcuts by dragging commands to the keys of a graphical keyboard interface, or to click on any keyboard key in the interface to see and change all associated shortcuts (with and without modifiers).
Better multicam interface with automatic synchronization of clips based on audio analysis (i.e. built-in PluralEyes software). (I won't elaborate on this point since I've discussed it extensively in other threads)
Timeline Audio keyframes that only move left/right or up/down, depending on initial movement after selection. This would make it so much easier to reposition keyframes in the Timeline without inadvertently changing their dB values. And no, PP's current keyboard modifier to restrict audio keyframe movement to left/right or up/down does not work properly. It never did!
Intelligent audio waveforms in the Timeline. i.e. Waveforms that grow or shrink to graphically represent their volume settings.
Ability to change a clip's audio from Stereo to dual mono and back to Stereo after it had already been used in the Timeline.
Here's my short list. If you've used FCPX before, please add your suggestions to the list! Overall, I would much prefer that Adobe integrate some of FCPX's great ideas than the other way around, because after using FCPX for a week, it's become clear that Premiere Pro is so much closer than FCP to giving editors what they want and need. Just adding item 1 from my list would go a long way towards PP achieving the goal of perfect NLE!
Thanks for reading.

Thanks for your post. I hope you have already filed feature requests for these.
I like this one. Let's all file feature requests for keywords to sort and organize clips: http://www.adobe.com/go/wish
You can use the .kys file to share or move keyboard shortcuts. Are you familiar with those? I modified the Help file to include this info: http://adobe.ly/WAfgCZ
A graphical UI for keyboard shortcuts is a feature request I'd like to see implemented, as well: http://www.adobe.com/go/wish
Automated synchronization of multicamera clips based on audio waveforms (merge clips too) would be wonderful. That's a feature request.
Constrain audio keyframes vertically or horizontally with a keyboard modifier? I don't know of that one that is supposed to work. I have a feeling that this is a feature request.
Better audio waveforms? Feature request.
Changing audio tracks on the fly? Feature request.
Pierre-Louis, I actually am an editor and with 23 years of pro experience. Here's a basic summary:
I've been chopping bits of tape together since 1983.
I have a BA in Radio, TV, and Film.
I started as an online linear editor (GVG, CMX, etc.) in the late 80's.
I've edited, color corrected, and provided motion graphics for numerous productions, including features, commercials, music videos, web video, and corporate video in LA and San Francisco.
I was formally trained at Video Symphony on Photoshop, Media 100, After Effects, and Avid Media Composer by Hollywood experts in 1997 (6 month long boot camp certification).
Original 2-popper known as "Telly." My hero was Ralph Fairweather (R.I.P.), the sole voice inside Apple that helped us all with FCP 1.
Founded the first FCPUG, SF Cutters, from which all FCPUGs sprung. I helped found the LAFCPUG, as well.
I started training people Final Cut Pro professionally in 2000 (BAVC, Video Symphony).
I was an Apple Certified Trainer for almost a decade. I was one of the first in the program chosen by Apple, and always in the "first class" of trainers for every rev.
Wrote the well-received book, "Motion Graphics and Effects in Final Cut Pro." See what my friend, Ken Stone has to say about the book.
As a result of my book and reputation as a trainer, I worked inside Apple on the documentation for Final Cut Studio 1 (LiveType, FCP, FC Express).
I worked on the XSAN team testing XSAN after I finished with FCS 1.
I worked on 2 features at Pixar (Nemo, WALLE) doing pre-viz using After Effects.
I worked on Final Cut Studio 3 inside Apple as an "internal editor" (beta tester), mainly working on Apple Motion.
I have worked at Adobe as a tech writer, community manager, and now as the support lead.
There's more, but I'll stop there.
Since I am an editor, trainer, tech writer and support person, I do understand your requests, however, I do have limited capability to help users change features. I am only one man with one voice. The best ammo for getting new features implemented is the feature request form.

SNMP Query for Byspass Status (AIP5)

I'd like to monitor the state of Bypass mode for the ASA-SSC-AIP-5 and would like to know if I can check this with SNMP and if so, which OID.
I started messing with SNMP and the SSC5 a while back and started a thread about snmpwalk causing it to crash. After that, I never really picked the project back up.
I've been known to miss the obvious every now and then, but I was dissapointed to see that there wasn't an (obvious) way for the device to alert you when it automatically goes into bypass mode. This should be a feature request.

IPS provides SNMP traps for different interface conditions like link going down or up, traffic bypass started, etc. Below is one such example
Received SNMPv2c Trap: Community: "public"
From: 10.89.149.204 mib_2.1.3.0 = 38429472
snmpModules.1.1.4.1.0 = ciscoMgmt.138.2.0.1
ciscoMgmt.138.1.3.3.1.3 = 3                      <====    index can be mapped to index obtained from snmpwalk
ciscoMgmt.138.1.3.3.1.4 = 5                      <====    Traffic bypass started
ciscoMgmt.138.1.3.3.1.5 = 4
ciscoMgmt.138.1.3.3.1.6 = 38429472
All you need to do is enable sending traps from the sensor.
qssp-8085(config)# service notification
qssp-8085(config-not)# enable-set-get true
qssp-8085(config-not)# enable-notification true
qssp-8085(config-not)# read-only-community public
qssp-8085(config-not)# read-write-community private
qssp-8085(config-not)# trap-destinations x.x.x.x           <===== trap destination
qssp-8085(config-not-tra)# exit
qssp-8085(config-not)# exit
You can configure separate community name under trap-destination. If not provided then the read-write-community will be used to send with the trap.
Hope this helps
Madhu

Write community in pix501

Similar Messages

Maybe you are looking for