Written instruction how to install a Canon SD 770 IS Battery Door Cover?

Hello,
Re: Canon SD 770 IS Battery Door Cover Replacement
Do you have a description how to install this battery cover? You can’t just pop it in, probably have to loosen some screws on the body.
Thank you,
Bernd

bkeine wrote:
12 JAN 2014
This is not a satisfactory answer - for me. This minor repair to be performed by a Canon Factory Service Center Technician will probably cost me half the price of a new camera.
I am an engineer and well versed with watch and similar repairs, therefore a simple sequence of removing screws etc. would have been sufficient.
The battery door cover is extremely flimsy plastic and breaks very easily, probably by loosing the softeners over time which leads to the part becoming very brittle. Numerous websites selling this item attest to that.
I was hoping that a forum would give people some practical advice and not simply refer to a factory repair.
That I could have done by myself.
Thank you,
Bernd
I'm sure your snarky reply will get you satisfaction.

Similar Messages

How to install printer canon MX 393

Dear Sir,
could u help me how to install printer canon MX 393.

This explains:
http://support.apple.com/kb/PH14143

Instructions how to install more RAM Intel iMac 17"

Does anyone know where i can find instructions on how to install more RAM? Preferably with illustrations.
Thanks,

It´s supposed to be a phillips 2 screwdriver. It may also be difficult to open the lid if the screwdriver is too sharp. In Sweden we don´t usually call it by that name. If I only had read my swedish owner´s manual I would have knewn, or if I just had looked at the bottom of the computer before I purchased a phillips 0 screwdriver. That screwdriver might be useful in other situations and was quite cheap though.

HT4859 Did somebody find instructions how to install the same iCloud on a two iBook's, Arnold Robbé

I have a iPhone4S, MacBook Pro and MacBook Air, all with uptodate systems etc.
How can I install iCloud serving all these 3 devices ?
No instructions found so far. Thank you. Arnold Robbé

I have a iPhone4S, MacBook Pro and MacBook Air, all with uptodate systems etc.
How can I install iCloud serving all these 3 devices ?
No instructions found so far. Thank you. Arnold Robbé

Instructions: How To Install Logic Studio on External Drive

Sorry for starting another thread, but this will turn up in a search engine inquiry better than the other thread, so please delete the other one instead. I believe the subject heading wording will be more search engine friendly
Okay after much digging , I have found out what parts of Logic Studio 9 can & cannot be installed on an external Drive and here's how I did it:
http://www2.picturepush.com/photo/a/4177710/img/Anonymous/Picture-1.png
http://www5.picturepush.com/photo/a/4177713/img/Anonymous/Picture-2.png
Then after everything is installed:
Library>Application Support>Logic>EXS Factory Samples
Dragged to the Ext. HD got 3 gigs out of it
Then Library>Application Support>GarageBand>Instrument Library>Sampler>Sampler Files (NOT SAMPLER INSTRUMENTS !)
That scored me another 12GB
Installing that way allows approx 38GB of Logic on an Ext. HD
Message was edited by: Geoff J

If you want, you can install your OS on the external drive and boot up from that by setting the external drive as startup in the system preferences. Then you can install ALL of logic on it instead of using the internal at all. I've been set up this way for years.

Need instruction how to install Windows XP on Satellite A200-1AE

Hello can some one write a instruction of installing Windows XP Professional on this notebook?
What I need before instalation?
I have oryginal Windows XP. Which drivers i must have before? And what about boot?
I guess that my PC have SATA drive and XP setup don't support it.
Can I burn driver on CD? Becouse I don't have FDD.
Thanks for help.

You need instruction?
Search in this forum for similar threads about this theme.
You will find many threads!!
But here is a little hint;
You need to include the Intel matrix Storage Manager into the XP setup.
Without the iMSM the XP OS will not find the HDD!!!
The iMSM can be installed using the USB FDD drive or you can create a new XP CD using the freeware tool called nLite.
After the OS installation, you should download and install the Toshiba drivers from the Tosh European driver page.
PS: should check the driver installation instruction txt file before you will start to install the Toshiba XP drivers

How to install the Canon IR C4580 using OSX 10.6.6

We have a Canon IR C4580 at the office hooked up to the network. For the life of me I cannot install the printer to my new laptop, although it works fine on my old G4 desktop as the driver was installed on a previous version of OSX, now running on 10.6.6.
Does anyone have an update when Canon will have a fix to install the IR C4580 properly on OSX 10.6.6?

bdapice wrote:
Does anyone have an update when Canon will have a fix to install the IR C4580 properly on OSX 10.6.6?
The current UFR2 v2.2x driver is working fine on 10.6.6. If your iR C4580 has Postscript support there is also the Canon PS3 v3.20 driver and the Canon PPDs. If your iR C4580 has an imagePASS-H1 attached, which is a white metal box that will be hanging on the back of the copier, then you will need to ensure the H1 has system version 2.0 so that you can use the OS X 10.6 driver for the H1.
So can you confirm which printer controller you are using with the iR C4580.

This H P computer is new ( 3 months). Need written instructions how to scan, transfer my images, pictures to my computer and then how to transfer those item to another web site

I need instructions on the above subject. I want to send, transfer, download from my PC to someone else web page. I have no clue right now

Although my question has not yet been answered, I have since discovered that I asked on too specific of a forum. I have re-posted it on the general iPod forum and will shortly be marking this thread as answered to avoid confusion.
The new version of this post is it at:
http://discussions.apple.com/thread.jspa?threadID=1737777
Please post any responses there.

How to install Windows 7/Vista as 2nd OS and retain predesktop environment (service partition)

This is a step-by-step instruction how to install Windows Vista or Windows 7 as a second OS on a Lenovo Thinkpad that originally shipped with Windows XP AND how to retain the access to the Lenovo Service Partition.
I have been searching the internet for instructions like these but could not find anything useful. So I am posting it
here. Maybe this helps other users.
I have tested the procedure below with installation of Windows Vista Ultimate (64bit) and Windows 7 Ultimate (64bit). I believe that the procedure will also work with the 32bit versions of these OSs. I am not totally convinced that this works when the OS to install is Windows XP (64bit or 32bit). XP has a completely different boot sequence compared to Vista or 7. The basic steps would remain the same, but the XP setup is less forgiving when it finds an unknown partition. If somebody wants to try it out, please post your results as a reply to this forum entry.
Never never never try to install an older OS (like Windows 2000 or NT) as a second OS when XP is already installed! This is doomed to fail.
The procedure below does NOT work for Linux installations. I am not a Linux wizard, but any Linux bootmanager I know about is incompatible with the Lenovo Service Partition.
The procedure was tested on a Thinkpad R61 model 8918-B9G. It should work similar on other models.
You definitely need a service partition with Rescue&Recovery version 4. It will NOT work with older versions of R&R or if the service partition is not a type12 partition (see below how to find out about that).
I assume that the harddisk partitions are unmodified, i.e. still have factory settings. This is likely the case if you
never attempted any OS install or recovery action. If this is not the case, the procedure may or may not work.
You also need a bootable CD with a tool that can change the size of your current system partition. I was using gparted live version 0.5.2-9. ( http://gparted.sourceforge.net/ )
Everything you do is at your own risk. I am in no way related to Lenovo, other than being a customer using their
products.
Step 1) Make a full backup of your harddisk. Get yourself recovery CDs for your Thinkpad model if you don't have any. The changes we are about to make can completely screw up your harddrive. A typo is sufficient for that to happen.
Step 2) Power on the system. Check that you can boot into the Service Partition by pressing the Thinkvantage button when the startup screen appears. (Older systems may have a differently named button.) If there is a problem booting the service partition now, it is likely that the rest of this procedure will not fix it.
Step 3) From the service partition choose 'Warmstart' to reboot the system. Reboot Windows XP, logon.
Open a command prompt. CD to the following directory:
\Program Files\Common Files\Lenovo\BMGR
On a german language system (like mine) it is
\Programme\Gemeinsame Dateien\Lenovo\BMGR
If you have an older IBM system the directory may be named
\Program Files\Common Files\IBM\BMGR
or something like that. Maybe you need to search around.
In the following, I will call this the "BMGR dir".
Enter the following command:
bmgr32 /info /v
You should get an output similar to this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
        MBR Sector 1 Index: 1   Checksum: 00    Disabled
        MBR Sector 2 Index: 4   Checksum: 03    Passed
        MBR Sector 3 Index: 5   Checksum: FD    Passed
        MBR Sector 4 Index: 6   Checksum: 58    Passed
        MBR Sector 5 Index: 7   Checksum: 96    Passed
        MBR Sector 6 Index: 8   Checksum: 7F    Passed
        Data Sector Index: 3   Checksum: F1    Passed
        Original MBR Index: 2   Checksum: BD    Passed
        No Patch Sectors
        Checksum Byte: 00
        Think Flag: 1
        WinPE Partition (0-3): 1        Alt Boot Partition (0-3): 1
        Boot Config: 2 (Service Partition containing two Service OS's)
        Boot State: 0                   Alt Boot Flag: 0
        (Normal booting operation, will boot to Customer OS)
        RRU: 00000000 00000000          Prev Active Part: 255
        Previous Partition Type: FF     Patch IN: 0     OUT: 0
        CIRT Disabled
        TOC: 0000000000000000           Lock: 0
        Show Error: 0                   Halt on Error: 0
        CIRT Load Return: 0
        CIRT Execute Return: 0
        Pause Duration: 10              Scan Code: 0085
        F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
        Check Msg: There has been a signature failure
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   239 255 255           63    301296177
1   0x00   0x12      0 193 255   239 255 255    301296240     11279520
2   0x00   0x00      0   0   0     0   0   0            0            0
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
The important thing to look for is the 0x12 partition type in the partition table at the bottom. This is the service
partition. If you do not have a 0x12 partition, then you can stop here because the rest of the procedure will not work
for you.
Step 4) Shutdown and boot gparted from CD. Shrink the system partition to the desired size. Do NOT touch the service partition! Do NOT attempt to create another partition! Leave the new white space on the disk untouched! Apply changes and restart the system.
Step 5) Reboot XP. gparted has set the NTFS dirty bit. This will cause XP to run a full CHKDSK. Depending on how much files there are on the partition this may take considerable time. Let CHKDSK run to completion. When CHKDSK finishes, the system will automatically reboot.
Step 6) XP reboots now. Logon. When loading the desktop, XP will show a popup window, stating that system settings have been changed and new devices been discovered and that the system should be rebooted. This is ok. XP actually recognized the shrunk system partition and applied the necessary changes to its own system parameters. Click YES to reboot the system.
Step 7) XP reboots. Logon. Open a command prompt, CD to the BMGR dir and enter:
bmgr32 /info /v
The output you get should be similar to the output you have seen in step 3, except that the partition 0 size column
shows a smaller value.
Step 8) Shutdown, restart. Check that you can still access the service partition by pressing the blue Thinkvantage button when the system startup screen appears.
Step 9) From the predesktop environment choose warmstart. Reboot XP. Logon, logoff, shutdown.
DO NOT SKIP THIS STEP!!! If you start the Windows Vista/7 install right after shutting down from the predesktop
environment, the Win Vista/7 setup program will screw up your harddisk! The Lenovo MBR bootmgr reboot takes two steps for completion. The first step is the shutdown and the second step is executed when booting from harddisk. A boot from the Windows CD will skip this second step and disaster finds its way...
Step 10) Insert the Windows Vista/7 DVD and boot it. Start the setup. Choose "Custom (advanced)" install. It will show the partitions on the disk. Select the white space (unallocated). Click on "disk options (advanced)". Click on "New" to create a new partition in the white space. Keep the default size, click "Apply". Click "Format". A popup window appears stating that the partition may hold OEM data. Continue. Click "Next". Installation starts.
Continued in the second post...

Step 11) Win Vista/XP will reboot several times during installation. You will always see the Windows bootmanager with an entry for "Earlier Windows version" and "Windows Vista/7". DO NOT DARE to touch the blue Thinkvantage button on any reboot or press any function keys!
Step 12) When the installation is finished, check that you can successfully reboot Win Vista/7 by selecting it from the Windows bootmanager.
Step 13) Reboot XP by choosing "Earlier Windows version" from the Windows bootmanager. Open a command prompt. CD to the BMGR dir. Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
Opened Master Boot Record to see whose MBR it is.
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   254 255 255           63    109675692
1   0x00   0x07    239 255 255   239 255 255    109676544    191619072
2   0x00   0x12    239 255 255   239 255 255    301296240     11279520
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
startLBA and size will of course differ, depending on the actual partition sizes you have set. Note that Windows setup moved the service partition to entry 2 of the partition table. If you do not see the 0x12 partition then stop here.
Otherwise the following step will likely screw up you harddisk.
Enter the following command (case sensitive?):
bmgr32 /Fbootmgr.bin /m0 /IBM /v
The output will look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /Fbootmgr.bin /m0 /IBM /v
installing MBR
finding free sectors
Sector 9 is free
Sector 10 is free
Sector 11 is free
Sector 12 is free
Sector 13 is free
Sector 14 is free
Sector 15 is free
Sector 16 is free
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Setting Think bit
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
This command reinstalled the Lenovo bootmanager in the MBR that was erased by the Win Vista/7 setup program.
Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
        MBR Sector 1 Index: 1   Checksum: 00    Disabled
        MBR Sector 2 Index: 11 Checksum: 03    Passed
        MBR Sector 3 Index: 12 Checksum: FD    Passed
        MBR Sector 4 Index: 13 Checksum: 58    Passed
        MBR Sector 5 Index: 14 Checksum: 96    Passed
        MBR Sector 6 Index: 15 Checksum: 7F    Passed
        Data Sector Index: 10 Checksum: 01    Passed
        Original MBR Index: 9   Checksum: 12    Passed
        No Patch Sectors
        Checksum Byte: 00
        Think Flag: 1
        WinPE Partition (0-3): 2        Alt Boot Partition (0-3): 2
        Boot Config: 0 (Service Partition containing one Service OS)
        Boot State: 0                   Alt Boot Flag: 0
        (Normal booting operation, will boot to Customer OS)
        RRU: 00000000 00000000          Prev Active Part: 255
        Previous Partition Type: FF     Patch IN: 0     OUT: 0
        CIRT Disabled
        TOC: 0000000000000000           Lock: 0
        Show Error: 0                   Halt on Error: 0
        CIRT Load Return: 0
        CIRT Execute Return: 0
        Pause Duration: 10              Scan Code: 0085
        F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
        Check Msg: There has been a signature failure
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   254 255 255           63    109675692
1   0x00   0x07    239 255 255   239 255 255    109676544    191619072
2   0x00   0x12    239 255 255   239 255 255    301296240     11279520
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
So you have actually regained the Lenovo bootmanager. But you are not done yet.
Step 14) Shutdown. Restart the system. DO NOT PRESS THE BLUE THINKVANTAGE BUTTON AT THE SYSTEM STARTUP SCREEN!!! IT DOES NOT WORK YET! When the system startup screen DISAPPEARS, quickly press F11 (maybe several times). The system should now boot the predesktop environment from the service partition.
Step 15) When the predesktop is there, choose "warmstart". When the system startup screen appears, press the blue Thinkvantage button. The system should again boot into the predesktop. The blue Thinkvantage button now works permanently.
Step 16) Check that you can boot Win XP and Win Vista/7 from the Windows bootmanager. You're done!

How to install the windows7 agent and monitor the same machine

Hi ,
I have installed OMS on Oracle Linux 5.7-64 bit machine. Now I am able monitor the OIM which is installed on Linux. I have some of oracle applications (domains) on windows7 machine. I want monitor the same. On em, agent deployment page I am not able to see the windows agents.
Can you please guide me how to install the agent on windows and monitor the same?
OEM version: 11.1.0.1
Thanks in advance
Regards,
Kishore Tummeti

If you just need to install some agents on Windows the best (imho) option is not to use the push option because getting Cygwin to run can take hours (if at all).
Here you find a good instruction how to install the agent by hand: http://www.peasland.net/?p=122
Sometimes the –silent mentioned in step 4b needs not to be put as second argument but as last argument.
Eric

How to install Oracle10gr2 into the IBM AIX 5.3 Server

Hi ALL,
Could you please give me instructions how to install Oracle10gr2 into IBM AIX 5.3 Server. Otherwise if any installation doucment please provide
Thank you all
Kishore

Hi Kishore!
Apart from posting an AIX question in a Linux forum it is not completely clear what your problem is.
Have you read the http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb19075%2Ftoc.htm&remark=portal+%28Installation%29
Installation Guide?
What are the problems you encounter?
cu
Andreas

How to install patch SAS disk FW 124232 on SunFire T2000

Hi,
Need complete instructions how to install the 124232 patch on SunFire T2000.
Any help is much appreciated.
Regards,
E

The instructions in the README included with the patch look pretty complete to me. What are you missing?

How to install the Vista on Qosmio G30?

hello,
i have bought vista ultimate 32 bit and want to install it on my g30 notebook, is there somewhere a step by step instruction, how to install it without having any trouble? i did a forum search but only found problem specific threads.
thanks in advance!

Hi Christian
You search for a step-by-step Vista installation instruction??
You dont need it. The Vista installation is very easy.
First of all you have to install an RAID driver (but only if your notebook supports RAID)
After this installation perform further with the Vista setup.
After the Vista installation choose and download theToshiba drivers from the Toshiba European driver page and install the Vista drivers in the right order. The right order you will find in the installation instruction txt file.
By the way; please check exactly what Qosmio G30 notebook you have and choose then the right Vista drivers!!!
Regards

Please help me with the step by step instructions on how to install a Windows server 2008 on a computer that has Windows 8 installed on it

Please help me with the step by step instructions on how to install a Windows server 2008 on a computer that has Windows 8 installed on it without formatting windows 8.Please email the steps , Thanks

Please help me with the step by step instructions on how to install a Windows server 2008 on a computer that has Windows 8 installed on it without formatting windows 8.Please email the steps , Thanks
Assuming your rig can support virtual machines, you can use Hyper-V and run another OS there.
Better practice however is to use a dedicated machine and use remote desktop to the server.
Corsair Carbide 300R with window
Corsair TX850V2 70A@12V
Asus M5A99FX PRO R2.0 CFX/SLI
AMD Phenom II 965 C3 Black Edition @ 4.0 GHz
G.SKILL RipjawsX DDR3-2133 8 GB
EVGA GTX 6600 Ti FTW Signature 2(Gk104 Kepler)
Asus PA238QR IPS LED HDMI DP 1080p
ST2000DM001 & Windows 8.1 Enterprise x64
Microsoft Wireless Desktop 2000
Wacom Bamboo CHT470M
Place your rig specifics into your signature like I have, makes it 100x easier to understand!
Hardcore Games Legendary is the Only Way to Play!

Is there an instruction sheet detailing how to install Photoshop Elements 13 (from a DVD disk), on a Windows 8.1 computer, and if so, where do I find it

Is there an instruction sheet detailing how to install Photoshop Elements 13 (from a DVD disk), on a Windows 8.1 computer, and if so, where do I find it?

Googled for an instruction sheet. Got the following.
https://helpx.adobe.com/photoshop-elements/getting-started/install-pse.html
and
https;//helpx.adobe.com/photoshop-elements/kb/photoshop-elements-installation-errors.html
(Don't know why the second one didn't turn into a link, that's the url that printed out at the bottom of the page)
In any case it doesn't matter. I returned it to the store where I bought it.
Rule #1; Don't use a product if the people who produce that product (software, hardware, etc.) don't properly support it.
User forums and\or chat lines, are useful and may help. But! They do not constitute proper support (not for installation purposes anyway).

Written instruction how to install a Canon SD 770 IS Battery Door Cover?

Similar Messages

Maybe you are looking for