Wrk54g Wireless broadband Router

I've just tried the easylink setup wizard and it runs though all the correct lights, light up then it says detecting router, then that changes to connecting to the internet then it changes to the following message Router Not Supported Easylink Connect is designed to set up Linksys networking products if you have an older Linksys product or non-Linksys router, then use the installation utility that was included with that product. Click back to re-detect the router or click Cancel to exit this wizard. I'm not sure how it has worked out that the router is not supported when earlier in the wizard I had to choose the router from a list of supported routers and the Model I have WAS there. any help with this would be greatly appreciated.

First off let me know who is your Internet service provider?
Connect the computer directly to router using Ethernet cable…. Access routers set up page using http://192.168.1.1 ….you will get username & password screen …leave username blank & under password use admin.
After opening the reset page may be you need to reconfigure the router as per Internet Service providers’ requirement.

Similar Messages

I have been using WRT54G wireless broadband router and WU...

I have been using WRT54G wireless broadband router and WUSB54G on my home PC for the last 2 years. It was working fine until recently I encountered serious connection problem.
The WUSB54G cannot connect with WRT54G.
Error message " Cannot assocaite with the access point.
I have checked the followings to try and solve the problem.
1) Refresh site survey the WUSB54G does not show my SSID, but it can show my neighbour'sSSID.
3) When I use my notebook with built-in wireless network adaptor to access wirelss broadband there is no problem at all. I can access my SSID.
4) I have try reseting the WRT54G and changing password but still can not solve the problem.
5) Uninstall and re-install
5) I have installed a new USB adapter (WUSB54GG) thinking that it could be the old WUSB54G is faulty. But still encounter same problem.
I am using Window XP Professional. What could be the problem?
Please provide your professional advice. Thank you.

Hi, Try to update firmware of router. You can get latest version from www.linksys.com/download, Hope it will help you

TS3274 Not for sure if wireless broadband router is working I have downloaded Itunes on computer I don't think I can coonect to Wi-Fi; any suggestions

How would I know if my Wireless Broadband router is working? I get a list oif Network to choose but then I am asked to put in IP address when not connected to the computer. If I am connected to the computer the computer I am assuming IP address shows but even though I have downloaded Ituned to the computer; I cannot retrieve Itunes or App Storeon the IPAD.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
 Cheers, Tom

MI424WR (Rev. F) - Wireless Broadband Router - Need Rev G for NAS

I want to put a Buffalo NAS storage device on the USB port on the MI424WR (Rev. F) - Wireless Broadband Router, but Actiontec says a firmware upgrade to Rev G is needed to do this. If I do the upgrade (will it even allow it?) will I trash my router such that it won't work (and I may not be able to restore it to Rev F)? Anyone have any experience attempting this?

davef wrote:
Not sure what you mean by "not enabled". I use this USB port on the router to charge my EVO smartphone.
There is indeed power on the USB port, so charging USB devices does work.
What I meant by "not enabled", is that there is no firmware support of any kind.
No mass storage driver, etc.

Have existing wireless broadband router. Installing TC, shall I continue to use my router as before ?

Have existing wireless broadband router. Installing TC, shall I continue to use my router as before ?

Up to you.. the easiest setup is to bridge the TC and plug it into the existing router.. setup wireless in the TC to either act as a new network or complement the existing one.

WRT-54GS wireless broadband router speed vs wired speed

Why is the wireless speed for my WRT-54GS wireless broadband router about twice as fast as when I connect through one of the ethernet ports on the WRT-54GS? This effects my decission on upgading my family's PCMCIA cards and whether it makes sense to introduce a HomePlug to get the signal to my desktop PC.
And why is my DSL modem coming in at 100mps but no where near that after it passes through the WRT54-GS wirelss router?
Thanks, lpb

I alreadt have V.6. I don't see a firmware update on the Linksys site later than that.

2 x MSI RG54GS2 802.11b/g Wireless Broadband Router

Hello
I have 2 computers and 2 MSI RG54GS2 802.11b/g Wireless Broadband Routers . I need to connect the routers between them wireless. What settings should I make ? I set the ip for both routers and every router comunicates well with his computer. DHCP is on , on both routers . I do not have any option to use one of them as a client. How do I check that the connection is done ? I Ping from one router the other ? Because I receive failed !
Please help

I`m have the same situation, but with the diference that i have 2 network segments, I have tried many configurations but anything .... Have you solved your case?? How??

WRT54G ver 6 wireless broadband router throughput

I have a DSL 6 Mb service and the service company (ATT) is reading an incoming speed to their modem of 7Mb but when I connect my PC wireless to the router and run a speedtest I get only 2.7 Mb. at the PC. This is quite disturbing because I get longer times downloading files and I'm paying for 6 Mb. I'm surprise to see no one has posted anything about speed of service.
I contacted Linksys tech help and they have no clue. I asked for the information that the engineers must have of the broadband degradation to be expected at the output of these units if any. They have no idea either. I can't believe that a company that makes wirelss units has not performed tests in their labs to see what bandwidth degradation the unit creates if any and then publish this information. Its like buying a car where the manufacturer does not know the HP of the engine or how much load it can carry.
If anyone can help me with this I certainly would appreciate it. If degrading the broadband tomore than 50% is normal so be it. I will have to buy another brand or connect hardwired to the service. But if this is the case they should DEFINITELY provide this information before selling these units. By the way this is with only one lap top (Dell Inspiron) at les than 1 foot away. If you connect more than one I assume the Broadband would come to its knees.
If anyone has DSL or Cable and wants to check if they are getting the band they are paying for go to SPEEDTEST.NET and click on run a test and you will get your actual speed for your downloads and uploads. You may be very surprised at what you are getting. Its a neat site and keeps your data and as you continue testing it will give you a graph of all your test and results.
Thanks

Most wireless users are able to get 50% to 70% of their wired router speed. A few have reported as much as 80% to 90% of their wired router speed. So first of all, test the wired speed through the router. It should be 6 Mbps, or very close to it.
Your wireless speed depends a lot on how good of a wireless connection you have to the router. A good connection is both strong AND clean. By clean, I mean that there is no significant other wireless signal that is interfering with it. Note that having "5 bars" only indicates a strong signal, not whether or not it is clean. For example, if your neighbor is using the same wireless channel, you could be getting a lot of interference from his signal.
Often, getting a good wireless connection is a matter of optimizing several different parameters:
First of all, give your network a unique SSID. Do not use "linksys". If you are using "linksys" you may be trying to connect to your neighbor's router. Also set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
Poor wireless connections are often caused by radio interference from other 2.4 GHz devices. This includes wireless phones, wireless baby monitors, microwave ovens, wireless mice and keyboards, wireless speakers, and your neighbor's wireless network. In rare cases, Bluetooth devices can interfere. Even some 5+ GHz phones also use the 2.4 Ghz band. Unplug these devices, and see if that corrects your problem.
In your router, try a different channel. There are 11 channels in the 2.4 GHz band. Usually channel 1, 6, or 11 works best. Check out your neighbors, and see what channel they are using. Because the channels overlap one another, try to stay at least +5 or -5 channels from your strongest neighbors. For example, if you have a strong neighbor on channel 9, try any channel 1 through 4.
Also, try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers. The antenna should be vertical.
Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. If your current network is not listed, enter its info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings".
In the router, be sure to turn off optional services like logging. Logging should only be turned on for diagnostic purposes, not during normal day to day use of the router, because logging will slow the router.
If the above does not fix your problem, download and install the latest driver for your wireless card.
Some users have reported improved wireless performance by switching to WPA encryption.
If you continue to have problems, try the following:
For wireless g routers, try setting the "Transmission Rate" to 54 Mbps.
If you still have trouble, download and install the latest firmware for your router. After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Hope this helps.

Connecting a WRT54G Wireless Broadband Router to a Westell DSL Modem

For some reason I can't get my wireless router to finalize the last step on installation on my desktop. I followed all the tutorials from the linksys help center and I still can't get the router to install correctly. I did ipconfig/release and ipconfig/renew. I made sure the IP address was in the 169.xxxxx range. Changed the default IP on the web based utility from 192.168.1.1 to 192.168.2.1 . When I changed all of the info mentioned before I could get internet service to my base computer, but I could not get passed the last step of installing the router and no wireless to any laptops. I have done everything by the book and it still doesn't work. If there is anyone that could help me, I would really appreciate it. I have DSL Internet service throught AT&T. My router is a WRT54G and my DSL Modem is a Westell Modem, Its black square shaped with five lights on the front.

As your Internet Service Providor is DSL follow this link

MI424WR (Rev. E) - Wireless Broadband Router MAC filtering limitation.

I can not input more than 10 MAC addresses into the Wireless Settings->Advanced Security Settings->Wireless MAC authetication->Enable Acsess list->Accept all devices listed below. When click Apply it returns the error message that no more that 10 items can be in the list. How can I increase that limit to say 128 ?
By the way Actiontec Support Respose was:
"That is correct. Verizon has limited the MAC Filter programming to a maximum of 10 devices."
Why Verison does that? And how can I increase the limit?
I have:
Firmware Version:
20.20.2
Model Name:
MI424WR-GEN2
Hardware Version:
E
Thanks.
Solved!
Go to Solution.

10 MAC addresses is a known limitation of the router and not likely to be changed.
FWIW, filtering of wireless MAC addresses serves no useful purpose. Wireless MAC address can easily be sniffed
http://www.zdnet.com/blog/ou/the-six-dumbest-ways-to-secure-a-wireless-lan/43

WRT54G Wireless Broadband Router Help

Somebody had gave me a WRT54G router and they didn't give me the cd that comes with it and I would like to set up a secure wirelsess network for my apartment would I still be able to do this without a cd? If so what do I need to do?

Who is your Internet Service provider ?
Follow this link if your Internet provider is cable .
Follow this link if your Internet provider is DSL .

How to set up the airport express with a linksys wireless-g broadband router

I need to know if and how to set up an airport express to use to extend a home wi-fi network. I have AT&T service with a 2WIRE modem. I am using a Linksys wireless-G broadband router. I also have the new Macbook Air notebook. The airport express keeps giving me a blinking amber light even when the ethernet cable (from the modem) connected. Please let me know how to set up an extended wifi network using this system. Any help would be appreciated.

If that is all that is done, the Express would not provide more wireless coverage. Instead, it would duplicate the coverage provided by the Linksys and there would be two WiFi systems covering approximately the same area. As per my above comment, one Express connects via Ethernet to the Linksys. The second Express provides the extension.
You must have misunderstood what I was saying.
Linksys is providing a wireless network.
The Express is connected to one of the LAN ports on the Linksys router using a long Ethernet cable (or Ethernet powerline adapters)
The Express is located on the other side of the house, for example.
The Express is configured to create a wireless network using the same wireless network name, security and password as the Linksys router
The Express is configured in Bridge Mode
This has worked quite well for me for years. Computers "switch" from one wireless access point to another smoothly and automatically while they move around the house.
Although this is an "extended" network, it is technically known as a "roaming" network.
This is what I was suggesting as a possible alternative without having to buy more hardware.

Wireless B Broadband Router (BEFW11S4) connects for only about 5 mins at a time

I have Wireless B Broadband Router (BEFW11S4). Worked fine for about 2 years. I've had a HP Pavilion for about a year now using the wireless and also have a desktop I use on it (wired). About a month ago the speed seemed to be lagging a little and the router was never secured with a password, so I changed that and added a password. Ever since then the laptop will not stay connected for more than about 5 mins. I have gone back and removed the password protect feature, but still have the problem. It has a problem connecting to the router. The signal bars always seem to be full, but still can't connect. I've tryed reseting the router, unpluging everything, etc and can't get it to have a steady connection like before. Sometimes I can connect to the internet even when it says "Not connected" in the wireless network connection 2 screen. I've tried to search and find a similar problem, but was surprised to not be able to find one. Any insight will help.
Thanks,
Lman

Thanks for the suggestions Wizzard. Although I did not know what all that stuff does, it didn't seem to help. I didn't not upgrade the firmware because there didn't seem to be any upgrades since 2003, before I bought it. Any other suggestions from anybody? Could anybody make an educated guess to whether it's the router or the laptop?
Thanks,
Lman

BEFW11S4 - Wireless-B Broadband Router questions

I have the BEFW11S4 - Wireless-B Broadband Router. Did it come with mac software originally? If so, is it possible to get the mac software from your company? Secondly, is there a way to disable the wireless signal on it and use it as a wired router? How would I do this? Would I do it in the network system preferences on my mac or would I need the software that came with the router originally?

Hi…
Linksys software CD does not operate on MAC OS. But you can still use the router with MAC. To configure the router with MAC OS connect the MAC to any of the Ethernet port of the linksys router. Login into the router by typing http://192.168.1.1 ( Default IP ) in the address bar of the IE. Leave the Username field blank and type admin as password (If you have not changed the router password.) Using the user interface you can also disable the wireless function of the router.

BEFW11S4 Wireless-B Broadband Router Issues

I have been having issues with my router lately. It is a Linksys BEFW11S4 - Wireless-B Broadband Router. It has the latest firmware and everything which was from like, April of 2005 since this is an older router model. I've had it for about 3 years now and have had no problems until this past week. I have Verizon DSL. Anyway, my network connection seems to fail every so often at least 6 times a day at random times. I use WEP security encryption and everything. Every time it fails, I have to reset the router and go into administrator configurations and retype the password then it starts working again. But it is annoying since I just lose connection for no reason when I'm in the middle of something. Even when it fails, it does not indicate that I lost connection or that my connection is weak. It says that the signal is still excellent all the time even when it stopped working and the Internet light is still on. Odd. Does anyone have any idea what is wrong or is it time for me to buy a Wireless-G router instead and hope that fixes the problem? Again, I have had no issues with the router and it has been working great for nearly 3 years until this past week and I did nothing to mess with it. Maybe is it just that the hardware is worn-out? I dunno, I just want this problem solved.

YouCanfindUs wrote:
Bad DMZ + Portscan = Reboot. I’ve noticed that a portscan will cause the router to reboot if you have a bad DMZ host specified in the DMZ settings. The “Dummy DMZ” is a known method for stealthing Linksys routers, but apparently doesn’t work due to this problem. This problem has been confirmed on the DSLReports discussion board as a problem thats been around for a while, not just in 1.39.2. I’ve found that even with a valid DMZ host, a portscan will sill hose the router. If you turn on the “daignostic logging” (see hidden features section), you can see log entries that say [HH:MMS] Free=xxx, where xxx is getting smaller and smaller until it resets. (Note: this happened with default filtering settings, no spi, block wan, etc)
UDP Traffic Can Cause Reboot. In much the same way as the DMZ problem, sending large amounts of UDP traffic can hose the wireless interface. I used QCheck to send 1mBit of information in 10 seconds from a desktop (wired) to a laptop (wireless). You can see the [HH:MMS] Free=xxx decline. When it gets to 0, the wireless interface activity light goes solid and the router locks. This bug hasn’t been confirmed yet on any message board or newsgroup. (Note: this happened with default filtering settings, no spi, block wan, etc)
hmmm..just curious what model number are you referring to? Is it BEFW11S4 ver 1 or 2???
Yesterday is history. Tomorrow is mystery. Today is a gift.

Wrk54g Wireless broadband Router

Similar Messages

Maybe you are looking for