Wrong credentials on multiple network devices...

I generated a report on Device Credentials using Device credentials Verification job and it cames back with wrong SNMP credentials, here's the weird bit.
I checked SNMP R & RW on the successful devices and failed devices, both have the same R and RW community strings!! Any ideas?
Thanks

It takes more than correct community strings for RME's Device Credential Verification to work. First, the devices must be SNMP reachable from the RME server. Have you verified the SNMP packets are making it to the devices? If you run a "debug snmp packet" on the non-working devices, do you see the incoming requests from RME? Do those requests make it back to the RME server. Next, check that if you have community string ACLs applied on the non-working devices that they allow the IP address of the RME server.

Similar Messages

Multiple Network Device Groups when importing to ISE using template

I have a question about importing a group of network devices into ISE using the template provided. The template only has a single column for Network Device Groups - is there a way to import devices and include more than one NDG? For instance, the NDG's we use are "Device Type" and "Location". I'd like to include both when doing my import and I've tried multiple ways to seperate the two strings within the column (comma's colons, semi-colons, spaces, pipes, tabs, etc), but i always get an error message that "NDG group does not exist". I also tried adding a new column into the template, but that just plain failed to import.
If there is any way to do this, I would appreciate any advice on how - I have to add about 40 devices per week to our ISE deployment and I'd rather not have to go in and add any parameters manually if it can be helped. Thanks very much!
Ross
BTW, we are running ISE ver 1.1.2 in case it is relevant.

Yes, you can do it. You have to use the pipe "|" to separate the groups. But please notice you must create the network device groups in advance.
For example, I have the following groups in my csv file to import a lot of network devices
Device Type#All Device Types#SWITCHES#375O-X|Location#All Locations#PERU#LIMA
But as a pre-requisite I have to create the network device groups.
If you have lots of network device groups, you can mass import them instead of creating them one by one.
Please rate if it helps

Share file with multiple network devices

hhow do I share the files on my airport time capsule with my Mac mini, iPad, iphone, windows based computers?

Mac Mini can access the Time Capsule under the SHARED heading on the left side panel in the Finder.
The iPad and iPhone will need an App installed like FileBrowser. Stratospherix - FileBrowser - Overview
PCs can access the Time Capsule drive by opening Windows Explorer and typing in the LAN IP address of the Time Capsule. Example....
\\10.0.1.1

Same network device gets discovered multiple times in scom

Hi All,
In SCOM 2012 , Same network device gets discovered multiple times.
For example, if we have an ip address 10.91.180.43 added to Network discovery rule.
When Discovery is run few times.
its gets discovered multiple times and shows 3 or 4 times under Network Devices.
Please help me to fix this issue.
Thank you
Siva

Hi dktoa,
Thank you for the quick reply. i would like to explain my issue in clear.
For example, if we have an ip address 10.91.180.43 added to Network discovery rule.
When Discovery is run few times. its gets discovered multiple times and shows 3 or 4 times under Network Devices. And it gets listed multiple times with same ipaddress not with different ip.
it will look like this
10.91.180.43
10.91.180.43
10.91.180.43
---- I read both articles, they are were interesting.
Do you mean to say that my issue will get fixed , if i change the AccessAddressFormat = "AUTOADDRESS" as
AccessAddressFormat = "LOOPBACKADDRESS"
Please guide me if i am wrong.
Thank you once again.
Regards
Siva

SCOM Monitoring Multiple interface of a same network device

hi
I have deployed SCOM 2012 R2. I have discovered around 200 network device by using device's loopback IP adress with SNMP v3.
100 dvices are in the branch offices those are connected with 3 links in three interfaces respectively. Even if two link is down, i can see that my network device is healthy since network device is discovered with the loopback address. How can i configure
my network monitoring so that even if one link goes down i can see some kind of warning or error in the particular network device in my monitoring pane. Please say if my infrastructure is unclear.

Hi,
You can create built-in network ICMP only network monitoring for the three interfaces respectively.
Using the built-in network monitoring within Operations Manager 2012 to monitor network devices using ICMP only mode
http://blogs.catapultsystems.com/cfuller/archive/2013/07/03/using-the-built-in-network-monitoring-within-operations-manager-2012-to-monitor-network-devices-using-icmp-only-mode-scom-sysctr.aspx
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

How do I use the time capsule to share itunes music between multiple apple devices? Also, is it possible to control the music on one device using another, and how do you set this up?

How do I use the time capsule to share itunes music between multiple apple devices? Also, is it possible to control the music on one device using another, and how do you set this up?

unless i'm missing something, i think you got mixed up, this is easy google for walk throughs
i'm assuming this is the new 3tb tc AC or 'tower' shape, if so, its wifi will run circles around your at&t device
unplug the at&t box for a minute and plug it back in
factory reset your tc - unplug it, hold down reset and keep holding while you plug it back in - only release reset when amber light flashes in 10-20s
connect the tc to your at&t box via eth in the wan port, wait 1 minute, open airport utility look in 'other wifi devices' to setup the tc
create a new wifi network (give it a different name than your at&t one) and put the tc in bridge mode (it may do this automatically for you, but you should double check) under the 'network' tab
login to your at&t router and disable wifi on it
add new clients to the new wifi network, and point your Macs to the time machine for backups

Screen ipad doesn't respond during video viewing home sharing with multiple iOS devices simultaneously

A have a problem with the videos app and iTunes home sharing on multiple iOS devices.
This is my setup. On my iMac 2006 with Snow Leopard I have:
- 100+ dvd's ripped in my iTunes movie section
- 600+ episodes ripped in iTunes TV-section in 35 TV-shows
- 1 apple tv, 1 iPad 2, 1 iPad mini
On an average evening my family is watching different tv-shows simultaneously on the apple tv, the ipad, an iphone, and an ipad mini.
This is done through home sharing on the one iTunes library.
All updated apps, software etc..
What happens on the ipads, after viewing for more than 10 minutes, the user interface doesn't show up when tapping the screen. The touchscreen doesn't respond, only the home button works. Clicking the home button closes the app, but the sound of the video keeps on playing. Opening up the videos app again gives a black screen with sound still playing and still no button or UI.
The only workaround which currently works is killing the videos app. Power off the ipad and power on again, reconnect to the shared library, wait until it has found all the content (1+ minutes) and startup the tv show again.
All in all, a nasty way to pause your viewing or switching to another movie of tv episode, or even wanting to finish viewing.
The problem has haunted me for a year now, patiently waiting and hoping software-updates would fix it. They didn't.
A fix would obviously hugely improve my user experience, getting it on par with Apples usual quality of service.
Anyone familiar with this problem? Apple: is it possible to fix it in an update?

Same here for over a year now.
You cant imagine how happy i am that im not the only one with this problem.
many of frinds have the same setup as me (ipad 2, 27"imac, express, apple tv 2)
No problem
I had the problem on Snow Leopard, lion and now on mountain lion.
I'am also starting to get a new problem - sometimes when waching a movie on iPad or ATV it just quits the movie and you have to start it again
on the iPad most of the time it also shows the wrong cover art. I tried all the hints here, and i works for a day or two then its wrong again
I store my itunes library on an external drive - you ???

Can I use my Time Capsule to set up multiple networks, or just one?

Can I use my Time Capsule to set up multiple networks, or just one? We'd like to offer the internet to clients who are at our studio, but don't want them able to access all our computers, so a second network for them would be useful.

Two big IFs here.
Not all versions of the Time Capsule have Guest Networking capability, so it might be a good idea to verify that first. Can you provide the model number of your Time Capsule. it's on the bottom of the device.....starts with an "A" followed by four numbers.
Next, assuming that the Time Capsule has Guest Network capability, the next requirement would be to verify that your modem is compatible with the Time Capsule for that feature.
Basically, you need a simple modem.....not a modem/router or gateway device that is often furnished by Internet Service Providers. If you are not sure what you have, post back with the make and model number of your "modem" and we'll see if we can find some details ont he device.

Why can I no longer configure multiple unsupervised devices?

It looks like Apple Configurator removed the ability to install a profile to multiple unsupervised devices, and makes the act of doing so with a single device much more laborious.
I use Apple Configurator to install a small profile that pushes a trust certificate, WiFi config, and Web Clip to enroll the device on our MDM server. I often set up large batches of iPads at once, so this made the process of getting each one onto our WiFi and enrolled much quicker. We have multiple admins on this network, and don't want to tie the devices to a single computer/Configurator install.
Any suggestions?

Unfortunately, even folllowing http://support.apple.com/kb/HT5833 it still appears impossible to use Apple Configurator to install multiple profiles on even one device at once without using Supervise mode.
So, if I want to install a profile which connects the device to a WiFi network (without which enrolment will fail) and then a Trust and Enrollment profile, I seem to have no option but to go through three cycles installing profiles, rather than allowing Configurator to automatically install each profile in turn in one pass.
This is extremely frustrating and VERY time consuming for mass deployments!!

Remove network device inventory from SCOM database

Hello Gurus
I have a quick question. I think one of the internal connectors in my SCOM environment has got deleted by mistake. As a result all the network devices that were being monitored previously has now disappeared. I believe because they were present in the database,
I can't discover them now. Is it possible somehow to list those network devices from the database, and then delete them, by using powershell and/or SQL.
Any help in this regard will be greatly appreciated.
Regards,

You can delete them by:
In the Discovery Rules option under the Administration Tab, you will be able to see all the network devices that are discovered. This shows the devices that are discovered and currently getting monitored in SCOM. You can select multiple devices and then
remove them.
Then Run in powershell Get-RemotelyManagedDevice to check that all Network devices deleted.
you can also check below link to remove/restore network device
http://technet.microsoft.com/en-us/library/hh212795.aspx
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"

ISE Could not locate Network Device or AAA Client

When authenticating using 802.1x and MAB, I recieve an authentication failure with the error 11007(Could not locate Network Device or AAA Client). The root cause that ISE spits back at me is "Could not find the network device or the AAA Client while accessing NAS by IP during authentication." I did pretty much everything by the book except instead of using a loopback interface I used a vlan with a defined ip address. Could this be causing the problem?
Here is the config of the port that I'm testing on:
interface GigabitEthernet1/0/9
switchport access vlan 9
switchport mode access
switchport voice vlan 8
ip access-group ACL-ALLOW in
srr-queue bandwidth share 1 30 35 5
queue-set 2
priority-queue out
authentication event fail action next-method
authentication event server dead action reinitialize vlan 4
authentication event server dead action authorize voice
authentication host-mode multi-auth
authentication open
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication violation restrict
mab
mls qos trust device cisco-phone
mls qos trust cos
dot1x pae authenticator
dot1x timeout tx-period 10
auto qos voip cisco-phone
spanning-tree portfast
service-policy input AUTOQOS-SRND4-CISCOPHONE-POLICY
end

I can ping both the vlan and the endpoint from the ISE. As far as allowing ISE to speak snmp and RADIUS to the NAD, I have enabled it on the NAD config inside the ISE. I have also double checked the snmp and radius shared passwords.
I have gotten MAB authentication to work but I am still getting the same error for dot1x authentication. Here are some of the configs on the switch.
aaa new-model
aaa authentication dot1x default group radius
aaa authentication dot1x defualt group radius
aaa authentication dot1x group group radius
aaa authorization network default group radius
aaa accounting dot1x default start-stop group radius
aaa server radius dynamic-author
aaa session-id common
ip radius source-interface TenGigabitEthernet1/0/1
radius-server attribute 6 on-for-login-auth
radius-server attribute 6 support-multiple
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server dead-criteria time 5 tries 3
radius-server host 10.10.10.47 auth-port 1812 acct-port 1813 test username test key 7 097940581F5412162B464D
radius-server vsa send accounting
radius-server vsa send authentication
dot1x system-auth-control
authentication order dot1x mab
authentication priority dot1x mab
dot1x pae authenticator
dot1x timeout tx-period 10

With Cisco Secure ACS 4.2 User accounts gets locked at first instance of wrong credentials even if configured for 3 attempts

Hello Everybody,
I am working with Cisco Secure ACS 4.2 and it is integrated with Active Directory at a Windows 2008 R2 functional level, user accounts that are set with lockout parameters (3 incorrect attempts) are locked out prematurely after the user enters the wrong credentials just once, the integration is done via LDAP.
I wonder if anybody has any idea why this is happening, because when I connect to a Cisco device or VPN, and type my password wrongly, on the Active Directory I get extra bad password counts.
Thanks in advance and regards....

Hello Scott,
Thanks for your answer. However we checked the ACS logs and it shows that we entered bad credentials just once, but in the Active Directory our account sometimes is blocked because we get at least 2 and sometimes 3 failures. This problem is only presented when we authenticate Cisco devices or through VPN, in normal circumstances, when users enter bad credentials on their computers, it works fine.
Thanks and regards...

Network devices discovered but not managed

SCOM 2012 R2 management group. A dedicated network monitoring resource pool consists of two MSs. These two MSs have been removed from AMSRP and other two default resource pools (AD.., Notification...) - is this correct?
Two discovery roles:
role1 runs on GWS1 discovered (explicitly) 5 devices and shown all "healthy". This rule was using AMSRP to monitor, but changed to the dedicated pool after it was created.
role2 (added after the dedicated resource pool was created) runs on GWS2 discovered (explicitly) 2 devices but shown as "not monitored"
How to find out what's wrong? (log files etc?)
Anything need to check with the resource pool settings?
Thanks.

Hi,
Do you mean that you have discovered the two network devices on your Management server, but it is not monitored.
This issue maybe caused by the proper management pack was imported, please go through the below article to get more information about how to monitor network device by using SCOM:
http://technet.microsoft.com/en-us/library/hh212935.aspx
Network Monitoring using System Center Operations Manager 2012
http://blogs.technet.com/b/rohitkochher/archive/2011/11/26/network-monitoring-using-system-center-operations-manager-2012.aspx
Regards,
Yan Li
Regards, Yan Li

Intermitent connection to network devices

Hi, until recently I had been having no problems connecting to other devices on my network from my iMac, I have a couple of windows PCs with shared folders, a NAS and one of the windows PCs also runs a VNC server. All of these were working fine until I went away for the weekend, I don't know if my girlfriend has accidentally changed any of the network settings but when I came back the iMac was connecting to the wrong wireless network (a nearby unsecured network), I tried to get it to connect to my own network which uses WPA but I kept getting "invalid password" or "connection timeout" messages even after double checking the password. I gave up and decided to leave it till the morning but when I tried to connect again the next day it just worked however now I am getting intermittent connections to my local network devices. The connection to the router and the internet is constant but the are frequent periods of several minutes where I cannot access network shares or the VNC server. All the windows PCs on my network are constantly able to access these shares and the VNC server. What could have changed on the iMac to cause this?

I just attempted to measure the period that the network devices are available/not available for by pinging one of the network devices continuously and it seems that the devices are available for exactly 10min then not available for exactly 10min which seems very unusual. any ideas?

Please help - multiple IOS devices, Apple ID's and synching

I have an iPhone and an iPad Mini that belong to me. Two of my kids have iPod Touch and soon a third will have one. So there are multiple iOS devices in the family, two of which are used only by me. Up to this point I've been managing them on one laptop running one iTunes library. I've made various playlists for the kids music, and I gave them each the specific games they wanted, and I put the games I wanted on my devices....certain games for the iPhone and larger, more involved games for the iPad Mini. I don't put music on the iPad because I only use music on my iPhone. So all 4 devices have a different selection of games, apps, and music on them. I've purchased everything with one apple ID....mine, and set each device up with it. Only I know the password so if one of the kids wants something, they still have to bring their device to me so I can put the password in for that purchase.
What I'd like to do is separate my kids apple ID's from mine. This way, they can use their apple ID's to sign up for other services, have their own saved game data in the cloud, etc. I'm running into situations where my son and I play the same game, but we keep overwriting each other's game progress because it's stored to my apple ID. But I still want to be able to control their purchasing, so I figured I'd have to attach my credit card to their new ID's as well, but just not give them the password, so they still will have to come to me to punch in the password to download something. But hopefully with this new setup, they'll have their own saved game progress that won't interfere with mine, even if we play some of the same games.
But how will this work if we synch them off my laptop? I don't want to get into creating separate libraries or anything like that, and I'd still like to be able to download some apps using iTunes and put them on the devices manually if I need to.
What is your recommendation on how to handle this??? How will it work exactly?

You can do anything you want with one iTunes, but:
Devices names must be different.
Don't sync anything under "Info" tab like Contacts Calendars etc. These info must be synced over iCloud. (Use a different Apple ID for each device)
Use the Same Apple ID for iTunes and App Stores settings in all iOS devices.
Message was edited by: cheonweb

Wrong credentials on multiple network devices...

Similar Messages

Maybe you are looking for