Wrong total point in quiz

I have four questions (on four slides), every questions is worth 1 point. If I go to Quiz Preferences and tell the project how many points that is required to pass the test I see total points of 8.
The question types i strue or false. Where can I find the other four points?

Have a look at Advanced Interaction panel (F9), it will show you all scored
objects. You probably have four scored interactive objects like buttons,
click boxes. You will have to take away that score.

Similar Messages

Referencing the wrong edit point in the timeline.

Hey guys and gals,
I have a strange issue that keeps popping up.
I cut a shot into my sequence and watch it. It looks fine.
The next thing I know I place a lower thirds GRFX or sometimes 'nothing' (just render the piece) and the next thing I know the shot is shifted to a totally different point within the clip.
I have to either recut it in, or slide it manually to the right point...and even then sometimes it dtill references the wrong in-point.
Any idea how to bypass or correct this situation?
I'd appreciate it.
Thanks!

Guerilla25 wrote:
I cut a shot into my sequence and watch it. It looks fine.
The next thing I know I place a lower thirds GRFX or sometimes 'nothing' (just render the piece) and the next thing I know the shot is shifted to a totally different point within the clip.
A clip that shifts once it is placed within a sequence has defective media. That might mean it was shot or captured or transcoded improperly. Or it might be a bad drive or you just may not know what you're doing.
You say "render" in a way that suggests your sequence does not match the media, or the other way around.
You imply a text clip causes the media to shift. This is not likely so you'd need to perform some tests to prove that for us.
bogiesan

Wrong SHipping point in delivery due list VL10G

Hi All,
We are facing vague issue related to delivery due list where it shows worng shipping point with respect to order.
Order has shipping point XXXX where as in deliverydue list it shows YYYY....
We checked the table responsible for showing values (Table VEPVG) in delivery due list.. It shows wrong shipping point YYYY as well...
Any idea why there is discrepancy...
Thanks in advance for help
Ghassan

Is it possible that you have different shipping points on the sales order, i.e. different at header and item level?

HT4859 I have restored a new iPhone from an iCloud backup but selected the wrong backup point. Can I restore again from a different point.

I have restored a new iPhone from an iCloud backup but selected the wrong backup point. Can I do the restore again from a different backup point?

Welcome to the Apple Community.
settings > general > reset > erase all content and settings, once complete the set up assistant will ask if you have an iCloud back up, follow on screen instruction to restore from it.

BEx report is showing wrong total but individual cell's total gives correct figure

Hi,
     For a bex report at sales office level, there are about 110 sales offices giving sales figures. But for some 2 sales offices, it's not giving the correct figure(for Total Volume). When I bring the Bex report at sales office level and customer level, I could get individual sales figures for some customers present in that sales office. But if I take the total of all customer's total volume, I'm getting exact figures (i.e., the correct figure for total volume)but it's total displayed by BEx report is wrong.
for eg:
Sales Office     Total Volume
101                    100
102                    150
103                    300
Let us take the above example. Here, Sales office 101, 102 are correct wit its total volume. For sales office 103, for validation if I bring customer as:
Sales office     Customer     Total Volume
103                    111               20
                         112               80
                         113             101
                         114               22
                         115               82
The total of above Total volume is 305 but it's displayed as 300.
Only for some one or two sales offices. It's cube is giving the correct data if I take up it's sum.
Plz help me to resolve the problem.
with Regards,
Antony Jerald.

Hi Sujit,
     Thanks for your reply. As you said, if it's because of exception aggregation, the same(wrong total)will be displayed for all the sales offices right?
Could you please let me know what are all the important tabs you want me to show?
Awaiting for your reply..
with thanks and regards,
Antony Jerald.

Itunes points to wrong files - points to random system files instead of mp3

I noticed this about a year and a half ago when my ipod would have an error that some of the files couldnt be transfrered. Upon further inspection, it seems itunes occasionally gets confused about where files are located. The files will look fine in itunes but wont play. If I right click on them and chose "show in finder" the file that should be an mp3 in my library, is actually pointed at ical/contents/resources/italian.Ipoj/iCal Help/gfx/priority.gif
Which is totally bonkers. It's a totally random operating file.
Now I could go in and delete and re-import these files. Eventually that is what I have ended up doing in the past. But now it's happened to about 700 files (out of about 18,000) and it would take a century for me to go through each track and find out which ones that has happened to.
I know there are some applescripts out there for missing and dead tracks, but I can't seem to find one that just checks that we're pointing to the CORRECT file. keep in mind, these correct files actually are where they are supposed to be. Itunes is just linking to the wrong files.
Message was edited by: James Campbell

I am experiencing the same problem and after restoring from backup I either still have some wrong pointers or the problem is returning.
One way to find out which tracks are pointing to random files is to sync your whole music library either in one go if it's small enough or in parts to an iphone or ipod. You will then get a dialog with all the files that won't play on the device.
How do I relink them manually? Can't work it out.

Wrong total in Account hierarchy

Hi
I have 2 application where the only difference is that one is YTD (Legal reporting) the other is Periodic (Forecast). They have exactly the same dimensions and are in the same AppSet.
My problem is that the total for my P&L is different eventhough the data are exatly the same. It is my Periodic application that returns the wrong result, only 0.73, but wrong non the less.
If I add the detailed records together, they return the correct result.
Any suggestion welcome
Jesper

Thats ok, the only way to avoide mistakes i to do nothing :O)
The legal application is YTD the Forecast is Periodic, my error only appeares in the top of my account hierarchy.
From net result to net reslut including subsidiaries,
I have
Netres with the parent netressubs
subs.8000 with the parent netressubs
subs.8009 with the parent netressubs
Last 2 are base members
I my case there are no values on the last base members, meaning that the result of netres and netressubs should be equal, but is is not there is a difference of 0.73.

GTM - wrong shipping point determination

Hi ,
Currently we are implementing SAP - GTM (Global Trade Managment functionality ) for our client and I am reletively new to this functionality. While creating one transaction cyles in the SAP system I am facing following problem :
Issue .While creating delivery document against sales contract/sales order through TEW (Traing Execution Workbench),system opens the VL01N screen and instead copying shipping point & delivery date from sales order as it is,it proposes some default shipping point 0001 and wrong delivery date.Due to this system gives error and does not execute the VL01n transaction till the correct shipping point and delivery date is enetered.I checked default value in the user->own data also ,but no value is stored against the parameter id's of these two fields.
Looking forward for valuabel inputs on the above issue.
regards,
Sachin

Hi,
OSS note 1872977 changes the TEW, so that the shipping point is taken from the sales order, like normal SD.
/Torben

WIndows chooses the wrong Access Point

Hi folks, hope you can help.
I've set up my home network as follows. My cable connection runs through the cable modem and into the WAN port of a wireless router with the wireless disabled, thus acting as a plain gig-e router. THis router also acts as DHCP. Two CAT 6 cables run off this.
One to the ground floor, one to the top floor. THe ground floor has an Asus RT-N66U running as Access Point (no router). THe top floor has an Asus RP-N14 access point extender thingy. Both "APs" have the same ID, same password, same authentication,
etc.
My phones use this set-up as one would hope. When connecting, the phone grabs the stronger AP and uses that. If moving round the house, the phones (Android) will sometimes hang on to the originally connected signal, but will usually hop over in time or upon
disconnect/reconnect. My work laptop running Win7 also behaves nicely, and does the same
My Win 8.1 laptop is a PITA. It PERSISTS in choosing the top floor AP >50% of the time, regardless of signal strength and the speed it can negotiate. Right now it's persisting with a -80 db link to upstairs, despite being sat within touching distance
of the downstairs AP which is presenting -50 db. Resetting the upstairs AP (taking it offline) forces the 8.1 laptop to hop over but as soon as the upstairs AP comes online the laptop hops back to that AP.
I've tried turning up the aggressiveness of the connection in the hope that it will find the better connection faster (in case this was somehow the problem) but it just means it hops to the weak connection quicker.
Perhaps worth knowing is that after removing the wireless profile using netsh and reconnecting (with the results above of using the wrong AP) the network is named "networkname 2" when hovering over the icon in the bottom right corner of the screen.
No idea where it gets the number "2" from.
Help, please. At the moment I can either deny internet in half the house for my family or only work in the top half of my house with this laptop.... I'm off upstairs to post this.

Hi,
This behavior depends on the driver of Network adapter.
I suggest you update the network adapter driver from manufacturer's website to see what's going on.
If it doesn't work, I suggest you install an older version of this driver in Windows 8.1 compatibility mode to see if the issue was resolved.
Kate Li
TechNet Community Support

Wrong total in credit note

Hello,
nearly in every case creating a credit note with an invoice as base document via VB6, there is a difference in the total.
The only specialty is that I enter the PriceAfterVAT.
In general there is just a difference of some cent and somestimes even the whole invoice gets closed.
What´s going on with the DIAPI???
Greetz

If you are getting wrong calculations, you should report it to our Support Center www.service.sap/smb on the left side your will find "Messages". There you can report them.
You can also check if in an update the problem was already fixed.
Best regards,
Felipe

Total number of quiz questions in an introduction slide?

Hello,
   I have a simple Quiz with 10 total questions. I have an introduction slide with some basic information.
   I would like to include the total number of questions in the intro slide. (I know I can just manually count up the questions and add that as a text caption). I am wonder if there is a way to insert this dynamically as it is in the results slide.
    {total-questions}       doesn't just work on its own on any other slide.
Thanks! -Vinny

There is a quizzing system variable that has that value and you could
insert it in a text container cussing the X button in the Format accordion
. If you use CP8.it is in the style tab, in edit mode in the Character
part
Not totally sure about the exact name of the var. Something like
cpQuizInfoTotal.... Look in the quizzing category of varaiables. No CP on
my phone.

HP photosmart 7520 connects to wrong access point and looses connection

I recently installed a remote wireless access point in an outbuilding. I'm using a router with the same SSID and password as my main router with the same security settings. Only the main router is set to issue IP addresses. The system works fine with two laptops, a desktop, an Ipad and an Ipod. It provides continuous connections from my house to the outbuilding. Only the HP Photosmart seems to be an issue. At first the system worked fine then after a couple of days it lost its connection. I tried to the Wireless Setup Wizzard with no success. The Wireless Network Test results indicated that MAC address filtering may be enabled. This is not the case, MAC filtering in not enabled on either router. The next morning the printer was fine and connected again. I suspect that it is detecting the remote router and trying to connect through it. During the setup a warning came up indicating that two routers were detected with the same SSID and Password and that the printer might try to connect to the wrong router. It should not matter since the remote router connects and is issued IP addresses through the main router. The only difference in the routers is the BSSID. This uses the same number as the MAC filtering address, so I suspect this may be the problem. Any suggestions on a work around. The only thing I have found that solves the problem is turning off the remote router.

Hello there -
Is it possible your new remote access point only supports the 5Ghz band for N connection, or that it's connected to your primary router through a wireless N connection in the 5Ghz band? The 7520 only supports 2.4Ghz N connections. If your primary access point supports both 2.4Ghz and 5Ghz, that is likely why it's able to connect there while it cannot connect to the new access point. Many newer laptops and iPad/pods utilize 5Ghz N, which would explain why they can connect and your 7520 cannot. I'd recommend moving the 7520 closer to the primary router and using AirPrint to send your jobs.
***I am an HP employee***
The comments above represent myself and do not reflect the opinions of HP.

Wrong total file size

[root@localhost ~]# pacman -S planner gnumeric
Targets: planner-0.13-2 libgsf-gnome-1.12.3-1 gnumeric-1.4.3-2
Total Package Size: 2.2 MB
Proceed with upgrade? [Y/n] y
:: Retrieving packages from testing...
planner-0.13-2 [################] 100% 2055K 45.9K/s 00:00:44
libgsf-gnome-1.12.3-1 [################] 100% 20K 14.3K/s 00:00:01
gnumeric-1.4.3-2 [############ ] 79% 9761K 48.5K/s 00:00:52
I thnk there's something wrong here...
Greets, Xerverius

mm a few secs later:
checking package integrity...
error: archive gnumeric-1.4.3-2.pkg.tar.gz is corrupted
That probably explains.

Crosstab report with null or wrong totals

I have a crosstab report that when I put a field in an item report area and setting <all> for values I get null values and with other fields I get wrong results (less than I wait). If there's no report item, it's return the correct results.
I have checked the SQL and it not return any null value.
I believe that the crosstab try to aggragate and sum the null values of the empty cells in my crosstab.
Anyone knows how to fix it?
I'm using Discoverer 10g Desktop.

can you send your xml data and template to [email protected]

FM returns wrong total value for Limit type PO's

Hi all,
I am working on SRM 5.0 (SP13) ECS.
I have implemented the BADI "BBP_WFL_APPROVAL_BADI" for determining the Approvers for PO whenevr a PO is changed.If the diference between the Old PO value and new PO value is > 1000 and the approval text field(custom text under "Documents" link) is set to "YES",then the WF approval is required and the approvers are determined.
The above logic works fine for the Standard type PO's where the difference between the old value and new value is determined using FM "BBP_PD_PO_GETDETAIL" by passing the GUID (for the change version and the active vesion) obtained at runtime in the BADI.
However for the limit type PO's,whenevr I change the total value for the Limit item,I see that the FM "BBP_PD_PO_GETDETAIL" doesnt return the changed value but always returns blank!
Bcause I need to check bth the values i.e. Custom text set to "YES" as well as Total value diff ,I cant use the start conditions in tcode SWB_COND.ALso I need to fetch the approvers based on the price diff so I need this value at runtime in the BADI using the FM "BBP_PD_PO_GETDETAIL".
Please advise why the FM is not returning the changed values for the Limit type PO and is there any other way(other table/FM) to get the changed value at runtime for the LIMIT type PO.
Thanks for your time.
Edited by: Rads1234 on Nov 18, 2010 4:39 AM

Thanks for the rpely.
Yes.I am using the GUID available at runtime in the BADI "BBP_WFL_APPROV_BADI" which is the current change version GUID.I tried using that GUID to get the data from both FM as well as CDHDR and CDPOS tables.
I think this is something related to LImit type PO because for Standard type PO's the FM returns the corretc changed value (as in the screen) for the change version GUID.I fail to understand why the changed values are shwon on the screen but are not stored anywhere in the system before actually ordering the PO!

Wrong total point in quiz

Similar Messages

Maybe you are looking for