Wrong USB Speed

Hi there,
I have E-MU 0202 and when I click on the [Control Panel] icon on the bottom right the "configuration center" appears. I can select the device, sample rate but that's not the point. It is written there "USB Speed : 1.1" while it should be 2.0, right? What should I do to change it?
Now I have Windows 7 but I don't remember how it was working on Vista or XP. Simply I didn't noticed that before, I think.
Thanks for some answer!

michal_banszel wrote:
Hi there,
I have E-MU 0202 and when I click on the [Control Panel] icon on the bottom right the "configuration center" appears. I can select the device, sample rate but that's not the point. It is written there "USB Speed : 1.1" while it should be 2.0, right? What should I do to change it?
Now I have Windows 7 but I don't remember how it was working on Vista or XP. Simply I didn't noticed that before, I think.
Thanks for some answer!
Since you have switched from XP/Vista to W7, could it be possible that you need to install some "drivers" to get USB 2.0 mode available (drivers are bundled with motherboard or you can check from the support site for your motherboard)?
Also, is there an option for USB 2.0 support in system BIOS.
jutapa

Similar Messages

  • USB speed help!

    I have a macbook pro from late 2009. It has a 1.1 usb speed but I need a 2.0. Is there anyway to install an upgrade or get a plug-in host to get the 2.0 speed from my usb drive?

    A Macbook Pro from 2009 should have full USB 2 support. USB 2 has been around since the early 2000s. I would think Apple is not that far behind the curve. And cetainly not with Lion 10.7.3 installed.
    Something else is wrong. Like you have a USB 1.1 hub connected and your external is going through that.
    The port you are using is bad.
    The cable you are using is bad or very inferior and can not do USB 2.

  • USB Speed

    First off, I am disappointed that the new iPod I have been waiting for (video and photo and music) no longer supports FIREWIRE. I use a lot of firewire disks, audio interface, and have a nice hub... but if I decide to obtain a new iPod I now have to examine my USB speed.
    When you use the profiler tool and look at the USB tree on my 1.25GHz G4 iMac, you see three separate USB devices - two are 12 MBs and one iw 480 MBs - The keyboard and printer are on the slower ports, and I have a SanDisk reader apparently on the faster port.
    Is that the case that not all of the USB connections are high-speed USB? Should I be expecting that at least one USB connection on this computer will be a high speed USB?
    Thanks

    All three of the USB ports on your computer are USB 2.0; the keyboard as well as any USB devices plugged in to the keyboard will operate at USB 1.1 speed. The printer may also operate at USB 1.1 speeds.
    (9282)

  • USB speeds on late 2012 model Macbook Pro

    I recently bought a new Macbook Pro (without retina display) to replace the 15" MBP I bought in 2006.  The USB speeds are extremely slow.  For example,  I transferred a 650 MB file from the new MBP to a thumb drive.  It took more than 45 minutes.  When I then transferred to my 2006 MBP it took less than 4 minutes.  Both are running Lion.  What gives?  Is there a configuration issue or is there a problem with my USB ports in my machine?

    How to reset SMC like Shootist007 said: http://support.apple.com/kb/HT3964
    or try resetting PRAM: http://support.apple.com/kb/PH4405

  • Problem with USB speed

    Hi there,
    I am new to MSI forum, and have some questions.
    I have MSI K9NU Neo-V mainboard and have problem with USB speed . I have all the latest drivers installed and the latest BIOS for my mainboard but still have the problem that mainboard detects all USB devices like USB 1.1
    MB MSI MS-7270 ver. 1 (K9NU Neo-V)
    CPU AMD Athlon 4200+
    VGA MSI 8600 GTS
    Memory 2 x 512 MB DDR2 667 Corsair XMS matched Pair
    PSU Gigabyte GE-R 460 V1
    DVD-RW Pioneer DVR 112D
    HDD Western Digital WD2500JS
    OS Windows XP SP3 x86
    Any idea about this?!
    Thanks,
    Alek

    Quote from: Bas on 20-November-09, 21:57:20
    Did you install all the drivers listed here?
    http://eu.msi.com/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=261
    I also move this topic to the right area.
    Yes, everything is installed and updated with latest drivers even from nVidia WEB for ULi chipset. the devices that we are talking about are USB removable storage like 8GB USB Flash Drive from Kingmax, 2GB Flash Drive from Xerox, 1 GB USB Flash drive from Kingston, USB case for 2,5" HDD from Spire ... I can count till tomorrow

  • Cisco Prime Infrastructure 2.1 wired client show Wrong port speed.

    Hi,
    i have odd issue for some reason the port speed in the wired clients shown a wrong speed,
    can some explain how the speed detremained and why i'm getting a wrong speed port of 10mb for a pc/host when my network is at least 100mb,
    thanks

    Hi all,
    after a TAC with cisco they open a new BUG # CSCur33328    
    https://tools.cisco.com/bugsearch/bug/CSCur33328/?reffering_site=dumpcr
    thanks

  • Slow USB speed at MacBook PRO with 10.10.3 Yosemite

    Hello, I have problem with very slow speed during copying information on nay USB card - speed is much lower than on Maveriks and lower than on laptops on Windows.
    What can be possible solution to solve this problem? 3 GB is copying 30 minutes...

    Hello, I have problem with very slow speed during copying information on nay USB card - speed is much lower than on Maveriks and lower than on laptops on Windows.
    What can be possible solution to solve this problem? 3 GB is copying 30 minutes...

  • HomeHub 3 - USB speeds painfully slow - known issu...

    Hello I have a BT HomeHub 3 - FW version 12 - on Infinity Option 2.
    I have recently bought a WD 2TB external drive and connected it to the USB port on the homehub in the hopes to have all my media on it to share across the network.
    It attached fine, was detected fine, and I've successfully mapped it as a network drive on my PC without a problem.
    The drive is formatted in NTFS, and my PC is connected to the homehub via the gigabit port.
    The read and write speeds though are painfully slow - pretty much solid at 2.0MB/s. Is this just "how it is" or is there a solution, because as it stands I can't see the point in there even being a USB port! I could download another version of the file 4 times faster from the internet than I could copy it locally to the HDD!!
    I can't find any information about this or indeed see many complaints, so I'm wondering if this is just mine?
    Any feedback would be appreciated - happy to receive technical answers.
    Thanks for any help!

     Keith, I have to say that your answer gives no technical insight of the situation,
     I highly doubt that this device does not have the processing power to do a transfer of more than 2-3 Mb/Sec,
     Don't forget there's even a gigabit ethernet port, and you can easily achieve very high speeds using lan or even the internet connection - forget that this is due to the hub being slow - no chance.
     Second point you mention, SMB protocol is not that efficient, that's not the reason for slow speeds again. I can confirm I've got an SMB server setup on a Linux 5 yeard old netbook in the Lan and it's still performing faster than 2 Mb / Sec. SMB is again NOT the problem.
     It's most likely a firmware issue where the USB port is either throttled down intentionally or not utilized as a proper USB 2.0 port - I think BT or whoever makes this box ought to give the community an explanation on the matter. When claiming that the usb port can be used to connect storage media they should also mention that the maximum speed is not more than 3 Mb/Sec - otherwise the statement is misleading as most people know that usb storage media perform a lot faster when connected to computers.
     It's like someone telling you, that his car drives like ferrari, but not telling you that it cannot do more than 20 mph.

  • WRT610 and USB Speed

    So I have a new 610n and just hooked up an NTFS format 500GB disk to the USB port.
    When transferring files from my laptop to the 610n USB drive (via a gigabit Ethernet link) I am only seeing something around 3-4MB/s transfer rates. This seems incredibly slow!
    If I connect the drive directly to the laptop's USB port I get around 30-40MB/s speeds (i.e. I max out the USB 2 bandwidth). Also, If I connect the USB drive to another computer on the network (my desktop PC has a 100mbs Ethernet connection to the 610n) I get around 11MB/s i.e I max out the Ethernet link.
    My guess is that this isn't a networking problem but rather a 610n USB driver problem.
    Does this sound right or have I done something incredibly stupid.
    Thanks, Pete

    In this case you should try to Upgrade your router's firmware and then re-configure it...
    Download Firmware 7.27 MB...
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - 192.168.1.1...Leave the username blank & in password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    NOTE : You should disconnect your Hard Drive while upgrading and resetting the router...

  • Kt4 Vl Giving Me Wrong Cpu Speed.

    I have the KT4 VL mobo running a AMD XP 2400 but it keeps showing up as XP 2600.
    I have set the fsb in the bios to 133 and every thing else on auto. The heatsink fan is on properly with good thermal compound etc etc. Under stress the comp as been locking up but the cpu temp is 40 c.
    What is wrong?
    Cheers.
    Leon.

    I think the bios reports the "model" of the cpu depending on the multiplier and fsb speed, why don't you check with a program like cpu-z or wcpuid to see what fsb/multiplier/speed the think you are running at? I think the standard specs. for the XP 2400+ is 15x133=1995Mhz+-2Ghz.
    I think there were 133Mhz bus 2600s, but if you have bought it recently, you shouldn't get that 2600 rating without the 166mhz fsb...
    If your computer is running and 40degrees C and you are sure the heatsink is properly installed with thermal grease/material, maybe your hangups are not caused by the cpu... check your memory settings...

  • T42 USB Speed

    Hi,
    I have recently reinstalled Win XP on my old T42 and have now found that both the USB ports only work at low speed. I used to have the problem with one being high speed (i.e. USB 2) and the other low ( i.e. USB 1) but now they are both slow. I have installed all available Windows updates as well as all those found using Lenovo's System Update but to no avail. The most puzzling thing is that for a while I was getting one of the posts to work at high speed then it just dropped down for no apparent reason and has not come back.
    The Device manager lists 4 USB controllers, 1 is ‘Intel® 82801DB/DBM USB 2.0 Enhanced Host Controller – 24CD’ while the other 3 are ‘Intel® 82801DB/DBM USB Universal Host Controller – 24C’ then the numbers 2, 4 and 7 respectively. The two external USB posts appear to be connected to the number 4 controller as disabling it renders them inert, and so to did changing the driver to the Enhanced one. Finally, disabling the Enhanced controller does nothing to the external USB devices so it is obviously not connected to them.
    Does anyone have any ideas about how to get my port working at the correct speed again?
    Thanks

    Welcome to the forum!
    Take a look at this thread:
     http://forum.thinkpads.com/viewtopic.php?f=2&t=70955&sid=d59ff189ee04c63c8b030269f1c2a261
    Good luck.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • Suddenly wrong network speed

    Hi guys,
    i'm totally lost here, cause i tried everything to fix my problem without success.
    ok, what happened:
    Currently my network card runs in 10 MBit mode only and cannot be switched to 1000 MBit.
    http://paste.ubuntu.com/566959/
    Here you can see that my card should be able to handle 1GBit but is currently set to 10 MBit and i don't know why.
    When i try to change it manually i get this:
    sxe@main ~ $ sudo ethtool -s eth0 speed 1000 duplex full autoneg off
    Password:
    Cannot set new settings: Invalid argument
    not setting speed
    not setting duplex
    not setting autoneg
    sxe@main ~ $
    *edit: It also happens when using a livecd (linuxmint). So i think its no OS failure. Maybe the router oder the network card?
    This setup worked in 1GBit mode for some month now without a problem and i did not change anything.
    My notebook, also running arch, with the same cable on the same router port works in 1GBit mode so i think there is something wrong with my desktop computer?
    Hopefully someone can help me. 10MBit sucks.
    Thx
    Last edited by sxe (2011-02-14 16:02:09)

    Link partner advertised link modes:  10baseT/Half 10baseT/Full
    Did you check the other end of the link? Try forcing the speed on both sides. Check if the network card vendor has any test utilities, it might help discover the problem.

  • Fire Wire 400 vs 800 vs USB speed

    A Fire Wire 800 port has a faster rate of transfer than both the Fire Wire 400 and a USB 2.0. Is a Fire Wire 400 port faster than a USB port and if so is it considerably faster than the USB.

    Hi mick1964;
    USB 2.0 is the slowest. I know it has a quoted rate that is greater then FW400 but that it burst rate which it is not capable of sustaining.
    Generally FW400 is about 40% quicker then USB 2.0 for sustain data transfers.
    FW800 is faster then FW400.
    Allan

  • Poor USB Speed Issues

    Connecting anything to my machine via USB has become painfully slow. When connecting an iPod to the USB port on the front of the machine, a window will sometimes popup saying "You are connecting to a USB 1.1 port - connect to a 2.0 port to ....etc etc"
    It IS a USB 2.0 port - Do the internal USB controllers go bad after a while? My machine has a lot of time on it and cannot think of anything else that could be the cause.
    And if so, what do I replace?

    Hi. The Apple Official on USB problems is here
    http://docs.info.apple.com/article.html?artnum=303598
    Although not mentioned there, sometimes using the FireWire reset procedure (bottom of the page here) helps USB
    http://docs.info.apple.com/article.html?artnum=88338
    USB on G5s has always been a bit suspect where USB power is concerned. Does it work ok plugged into the rear ports? A powered USB hub, such as
    http://catalog.belkin.com/IWCatProductPage.process?Product_Id=159070
    sometimes helps.
    The USB is on the main logic board (as are most things), so a PCI USB card would be required if it is duff.
    Good Luck.

  • Windows 8.1 Task Sequence is picking the wrong USB drivers

    I have a Windows 8.1 task sequence that hasn't had any driver issues on all the other desktops I've tested. Except the HP Compaq 6000 Pro. None of the USB drivers are working correctly unless I select Update Driver Software -> Browse my computer for
    driver software -> Let me pick from a list of device drivers on my computer then a list of 4 driver options appear. I can select any of them and they all work. I can't seem to figure out how to get it to select of those drivers by default. I've tried building
    a driver package and also a capture with the correct drivers selected. Neither have worked. Does anyone have any suggestions?

    Hi,
    Please have a look on the following thread. It might give you some hints.
    "use
    http://gallery.technet.microsoft.com/ConfigMgr-Driver-Injector-aae7d17d to 'grab' the drivers you've succesfully installed into your hardware and inject those to ConfigMgr. Create a driver package and use "Apply Driver Package" -step in your task sequence
    with WMI conditions so that this driver package only applies on to the right make/model."
    http://social.technet.microsoft.com/Forums/en-US/9094d303-d01d-44fa-801c-65578122c8bd/how-do-i-stop-windows-from-downloading-drivers-from-windows-updatewsus-during-operating-system?forum=configmanagerosd
    Best Regards,
    Joyce
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

Maybe you are looking for

  • All calendar entries are gone from my laptop since I turned on calendars in iCloud.  How do I get them back on the laptop?

    I just got my Outlook Calendar onto the iCloud . . . previously it was synced often from the laptop onto the iPhone not as often on the iPad.  Almost immediately I saw that the calendars on the pad and phone were working perfectly, so I downloaded th

  • BSP doesn't work when opened through MS Office application

    Hi Experts, I developped a bsp application to display directly all originals of a Document Info Record. The url has got some parameters: ex:http://maplmqa.sylvania.com:8000/sap/bc/bsp/sap/z_phl_guest/index.htm?dokar=ZPI&doknr=000000000000000000256416

  • Buying the right camcorder

    So...continuing a discussion I posted a couple weeks ago, I've been diligently reading and looking into buying a new camcorder.  I'm currently using a nice Sony Mini-DVD Handycam, but my problem is when I bring content into Premiere Elements I'm havi

  • Oracle 8i / 9i installation problem ...

    I am installing oracle 8i or 9i on my windows 2000 platform. it is successfully installed but after the first reboot of windows it gives the error message "oracle not available" and "memory relam does not exist". the same set of software is running s

  • Human Task - How to cause expiration of a task after SUSPEND

    Hello, This is a very simple question, but i don't know how to do this. I'm using the web services in bpel for manipulate the task. i invoke the operation suspendTask, it works success, but now i want set the expiration date time for 5 minutes for ex