WRT110: I want to create an access rule for one client for one application during one time period

I have a problem with one of the clients on my LAN which is running uTorrent to detriment of everyone else. It saturates the pipe. I have been unable to prod this user into bothering to tweak their settings to throttle bandwidth back and so have resorted to an access rule on the router which kicks that MAC address off during a particular time period during the day. But as irritated as I am about this slacker sense of outrageous entitlement, kicking them off entirely seems a tad heavy handed even for me.
So, In the router I can create a rule per MAC address and specify time. But is it possible to limit this to denying uTorrent ONLY? And if so what port or port ranges would I use.
Alternatively I already use a QoS setting for one of my VoIP TA's. Would I gain anything by degrading the application indirectly by creating a QoS = LOW for that port range? Again, I don't really care about any other application, just uTorrent and just that client. How much degradation is there really in setting QoS to LOW?

Well it wont make much difference, when you enable QOS service on your router. Yes it is possible to Deny uTorrent application from your Router. When you are Under "Application and Gaming" Tab, Under "Blocked Application" you will find "Application Name" , "Port Range" and "Protocol" so you need to input under Application Name "uTorrent" and under port range you need to input the port number which uTorrent application use and then under protocol select "Both" and click on ADD. Then again in Application you will find uTorrent , select and click on (>>) right arrow so it will block that application on your Router. By doing this it will block uTorrent from your Router.

Similar Messages

  • How to create a Credit Note to the client for purchasing of an Asset last y

    Hi,
    I have an issue in Asset Accounting as it showed bellow:
    Assets depreciation start date is 1st October 2007.
    We have run the depreciation up to November 2007.
    Than we sold the asset in December.
    However, after the end closed year 2007, client returned the asset in 1 st January 2008.
    So i need to create a Credit Note to the client for purchasing of an Asset last year, but we don't know how to create it?
    We thinks that correct movement should be debit in extraordinary cost / profits account, debit in asset account, credit in accumulated depreciation account and credit in client account.
    Plz help. I will assign full points for any useful answer.
    Thanks
    Edited by: Ricardo Pedro Rodrigues Ferrão on Dec 20, 2007 10:09 AM

    How did you sell the asset?
    You can just reverse the sale transaction by going to transaction AB08.
    Hopefull this may work for you.
    Regards,

  • Track the qeries that accessed a particular object during a time period

    HI,
    I have a list of objects on my schema and i need to track the list of sql queries by different users that accessed by object during this time period.
    i haven't enabled any auditing yet.
    is there any way i can get that list of queries and their schemas that accessed those particular objects during a particular time period.
    Can someone guide me please.
    Thanks in advance.
    Philip.

    Too bad you don't have a version number. Oracle functionality changes from version to version and in some versions you can do this and in some you can not.
    Look here for one way to accomplish the task:
    http://www.psoug.org/reference/dbms_fga.html
    Here for another:
    http://www.psoug.org/reference/audit_vault.html
    Here for another:
    http://www.psoug.org/reference/dbms_logmnr.html
    Consider posting more information when asking questions in the future.

  • I want to retrieve data for condition record during certain time period.

    Hi Experts,
    Please suggest me some T-Code for retrieving condition record date or Database Table where I can access the data with the  combination of Sales Organization, distribution channel, customer and plant.
    Looking for your expert comments....
    << Moderator message - Everyone's problem is important. But the answers in the forum are provided by volunteers. Please do not ask for help quickly. >>
    thanks in advance..
    With Best Regards,
    Bharat B
    Edited by: Rob Burbank on Jan 21, 2011 5:40 PM

    To search for data/all the relevant condition for a particular condition type(like for example PR00) for a particular date range you can got to VK13 and give that particular condition type for which you want the data for.After giving he condition type click on key combinations and choose for which condition you want the data for.
    Like for example I want to fetch the data for PR00 then I will go to VK13 ,give PR00 then choose the relevant combination and then take a F1 for the first field.by this I will be able to determine the table in which all the condition data is stored for the particular combination.Like for the combination of sales org./dist channel./customer/material we have the table A815.Now by going to SE16 and giving table as A815 i will be able to fetch all the relevant data.(in your case based upon the valid from and valid to date).You can also use table KONP for a particular condition record number details.

  • I want to create a 2.35.1 letterbox preset for a 4096x2160 resolution clip

    I would like to create 2.35.1 letterbox overlays that I can save a presets. I know I can create a title and draw rectangles at the top and bottom of screen, but I would like to create these into a preset that I can apply to clips as needed. Can anyone assist.

    You can't.
    A title is a title. It is not an effect.
    Perhaps if you explained what you really wanted to do. Do you want to edit in a 2.35:1 ratio? And then export that way?
    Or do you really want to export what looks like 2.35:1 in a 16:9 frame with black bars above and below?
    You can edit in a 2.35:1 sequence, and then just export it, or if you wish, you can drop it into a 16:9 sequence before exporting.

  • I want to create forms that are printable and not for web usage?

    I need to create forms that are for use in an office setting not only for web usage.  How do i do that?

    Hi,
    You may design a form in FormsCentral and then save the form as submission-enabled PDF form. Please check out this tutorial: Tutorial: Creating and distributing fillable PDF forms.
    Thanks,
    Wenlan

  • Want to create a posrtal Similar as this forum for internal Team use .

    I am new to portal development .
    so i want to make a Portal similar to this kind of forum for internal team use. I want to connect it to R3 so i need hepl regarding this .
    How and if possible anyone having a code would be very helpful.
    Developers please help in making this kind of a tool / forum for internal use.

    Dev,
    Check this blog, im sure it would be handy
    https://www.sdn.sap.com/irj/sdn/wiki?path=/display/KMC/Forums7.00Configuration
    Good Luck.
    Sandeep Tudumu

  • Q: Create a Pivot showing 3 sets of facts that relate to diff time periods

    I am having difficulties trying to simply display, in a pivot table format, a query for:
    - Budget by month for the past year
    - Variance for the entire year
    - Budget for the entire year.
    I want to show the Budget MTD broken down over 12 months, then the Variance consolidated to 1 column for 2012, then the Yearly Budget consolidated into 1 column for 2012.
    Unfortunately, I get 12 months of Budget MTD, 12 columns of Varience and 12 columns of Yearly budget.
    This feels like a very easy solution, but I just don't know how to do this.
    Thank you in advance for any help!
    Charles

    Motion-guru Marc Spencer from rippletraining.com has an episode upon Rigging at MacBreak Studio
    MacBreak Studio - Episode 151: Setting up a Rig in Motion 5 for Final Cut Pro X    
    … I'm no expert (as you notice in my first post ), but I'm really overwhelmed by the endless options, esp. in correlation with FCPX… on first sight, 'rigging' looked like 'bundled color sliders' to me, but by creating your very own drop-down menus you can create extremely powerful tools, handcrafted for your very own needs.
    For sport-reports, with its tons of statistics and inserts, you can create a box of 'title genrators' - once done, multiple times used, and extreeeemly fast then.
    … And when a 'nnob' like me manages it, it is really no rocket-science…
    Kudos to the DevTeam at Cupertino!!!

  • Creating Oracle service in Oracle 8i Client for Oracle 10g XE

    Hi all
    We tried Oracle 10g XE on one Machine X - OS Windows XP Professional SP2 , It had earlier Oracle 8i Client. It installed fine. It is wonderful and easy to install.
    Services started automatic for listner as well as OracleXE. We are able to create fresh Oracle Service in Oracle 8i client as well from the same machine X.
    Problem
    We are not able to create Oracle Service from another machine say Y which also has Oracle 8i client with the Oracle 10g XE service. We get TNS Problem error.
    Kindly guide as to how to make oracle service with OracleXE from some other machine. OracleXE does not install networking tools.
    Suresh Bansal

    Oracle XE doesn't install assistants such as dbca or netca, don't expect to find them, XE is a compact and limited oracle edition.
    >> We get TNS Problem error.
    Could you please further detail the tns error you got?
    ~ Madrid

  • High memory usage and error creating access rules

    Hi guys
    I'm having a problem with the memory and also trying to create some rules on the CISCO ASA. The version that I got installed was the 8.2.5.33 on a CISCO 5520 with 512 RAM, the memory usage is on 99% used, 1% free and because of that when I'm trying to create a new rule the firewall brings me the next error
    So what I did was a downgrade to the version 8.2 (4) 4 and the memory went down a little (82% used, 18% free) but I still got the error when I'm creating an access rule on the device. One thing and I'm not sure if this could affect on the performance are the number of access list and the object groups that are created.
    I already open a case with CISCO TAC and they are checking if the problem is with the memory capacity or maybe a memory leak.
    Also the doubt that I got is with the memory that I got now available should I can create access rules or 82 is still to hig to create a rule or and object group?
    Regards

    Hi,
    Can you check what is the amount of ACEs you have on the ACLs in use?
    I think if you use the command "show access-list " the first line should give you the total amount of ACEs in the ACL
    - Jouni

  • How to create a new rule in Windows Firewall to permit some specific IPs and block all other computers

    Hello,
    I have a Win7 PC. I want to block all incoming connections except 3 or 4 IPs. How can i do this?
    I created a new rule to block all connections using this steps:
    Inbound rules > New Rule > Custom > All Programs > All Protocols / Ports > All Local/Remote IPs > Block the connectiion > All profiles > Then i gave a name
    This rule works fine and blocks all incoming connections.
    Then i want to create a new rule to allow specific IPs using this steps:
    Inbound rules > New Rule > Custom > All Programs > All Protocols / Ports > Remote IPs: 192.168.10.5, 192.168.10.10 > Allow the connection > All profiles > Then i gave a name
    But 192.168.10.5 and 192.168.10.10 couldn't reach W7 machine. 
    (If rules are disabled or FW is off; both IPs could reach W7 machine)
    Thanks

    Hi,
    How did you check these two IP address? Through remote access? According to your description, it should only allow remote IP could access this computer. Please also allow local IP for test.
    Roger Lu
    TechNet Community Support

  • Access rule for Google Cloud Printer

    I want my user to access google doc, gmail account, google drive, and google cloud printer only but they dont get access to the google website.
    i make rule for it and block google search engine.
    after testing.
    google docx is accessing, gmail account is accessing and google drive is also accessing but i am not able to access google cloud printer. because google cloud printer is not a namespace
    so kindly help me out what should i do then what kind of rule i have to make so my user can also access google cloud printer. i dont want my client to access google search engine
    electrifying

    Hi,
    For this you can try creating a domain name set on the TMG server first. You can name the domain name set as "Google" for example. The entry in the domain set can be set to
    *.google.com  or the required domains . After that try creating an access rule with these properties:-
    1. From ---> Internal and Localhost
    2. To ---> Add the name of the created domain name set. (Google)
    Apply the changes and check if you are able to access the sites now.
    Check out this article : http://technet.microsoft.com/en-us/library/cc441706.aspx.
    Regards,
    Gijo

  • Create static nat rule cli

    I need to create a static nat rule that allows outside requests to the inside interface using http. I also need to create an access rule for this. Can someone please explain and show me the command I need to use in asa 5500 firewall version 9.x?
    Thanks!

    Hi,
    Do you mean that you want to create Static NAT rule where the local IP address is the actual IP address of the ASA "inside" interface?
    If so then that is not possible. You wont be able to connect to the "inside" interface through another interface even when using NAT configuration.
    You would have to use VPN connection to be able to connect to the "inside" interface IP address.
    Otherwise you will need to connect to the ASA with using the "outside" interface IP address.
    If you meant that you want to configure Static NAT for some internal host then the configuration format would be
    object network STATIC
    host
    nat (inside,outside) static
    Hope this helps
    - Jouni

  • Error while creating a business rule

    Hi all,
    I am trying to create abusiness rule from eas console when I am choosing business rule >repsitory view > rules>new rule> select outline,
    I am able to select a essbase database outline ,but while I am trying to select planning outline i am getting the following error
    WARN http-10080-Processor4 com.hyperion.hbr.plugin.planning.PlanningMetadata - Error connecting to Planning server metamorp-ee0b9e.
    Any suggestion?
    Thanks

    Hi,
    The first thing to always try is :-
    stop planning service
    stop eas service
    restart rmi service
    start eas service
    start planning service
    log into planning application you want to create a business rule for.
    log into EAS, create business rule, associate outline with planning app
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • ?Difference: To create 2 Transfer Rules or 2 Update Rules

    Hi,
    I need to load 2 similar flat files to a single ODS. Only change is that, during the load, in the first file, File1, I want to set a field, FileType, as File1; and during the load of the second file, File2, I want to set FileType, as File2.
    One update rule which loads File1, already exists. I wanted to create the second update rule(for File2), but I encountered problems because I kept receiving a message that the update rule already exists for the ODS.
    I went to the InfoSource tree and under the infoSource for File1, I could see the transfer rule; at this point, I was able to create a second transfer rule where I was able to set the second constant while loading File2, as FileType as File2.
    What is the effect of creating 2 transfer rules for the InfoSource, as against creating 2 update rules for the ODS, which was I originally wanted to do?
    Thanks

    Hi Amanda,
        If both file formats are same, it better to populate File1 or File2 dynamically then a constant. Every time not supposed to create new transfer rules and data soruce for new flat file.
        Instead of constant, write a routine for File Type. Based on file name sinply pass File1 or File2 in routine. Or
        Use function module "BAPI_IPAK_GETDETAIL" to get infopackage details including file name. from flat file name also File type can be derived.
        In this way no need to maintain multiple transfer rules or update rules. Existing flow is enough.
    Hope it Helps
    Srini

Maybe you are looking for

  • Error While Attempting to Checkout from Catalog

    Hello Gurus, I am currently using OIM 11g r2 and I have done the following: 1) Created a Sandbox 2) Installed the 9.1.1.7 AD Connector 3) Created an Application Instance for the AD Connector (with appropriate form, etc) 4) Ran the catalog scheduled t

  • Error while testing WSDL in Altova XML spy  tool

    Experts,     I am testing on a scenario. SOAP to Proxy synchronous. This scenario is working fine in production.I have used the HTTP security level as "HTTPS with client authentication" in SOAP adapter. I am getting the following error in Altova whil

  • Adobe Bridge Corrupts Canon CR2 files

    Viewing Canon CR2 RAW files from a Canon EOS 7D or Canon EOS 40D camera will corrupt some images. After Adobe Bridge creates a thumbnail of the CR2 files, some images previews will show the file with corruption (large white square or discolored areas

  • F110 - Lost Discount to be affected Inventory

    Hi, I understand the concept of net invoice during miro, the discount taken is affected during MIRO, the entries look like Dr GR/IR - 120 Cr Vendor - 120 Dr Vendor discount clearing - 1.20 Cr Inventory - 1.20 The posted documents are correct, and it

  • Configuring the  Synchronous scenario in XI

    Hello everyone! I want to configure a "Synchronous" scenario wherein when XI sends a message to a Marketsite, it waits for a response, then send back the response to the SAP system. My question is this, would I need to configure a "sender adapter" in