WRT120N - Disconnects and all LEDs blinks after firmware update

I have WRT120N, i recently updated the firmware. 1.0.06. only my bad is i done it wirelessly. so its basically interrupted.
I have tried, hard reset and power cycle and reinstall the firmware but still the problem occurs, this time its wired.
it happens intermittently. i have tried pressing reset upon turn on and reinstall firmware on the bootloader. it stablized for a while but then disconnects and blinking stikes again. 
is there anything i can do about this?

Try this:
http://compnetworking.about.com/b/2009/03/11/the-30-30-30-hard-reset-rule-for-routers.htm

Similar Messages

  • PSC 1410 shows E and all leds blinking

    Hi there everyone!
    I'm not an english speaker, but I will try to do my best in order to explain myself as clear as possible. This is the fact, I recently acquired a PSC 1410 a year ago. I know the previous owner bought it on 2006 and it was working properly till a month ago when the tricolor cartridge blew up inside the printer, literally. I turned on the printer and it showed me the Error message and all the panels led were blinking. I disconnected it from the wall outlet. So, I disassembled the printer and it was a mess, there was ink all over the interior, including the circuits board. Then I cleaned everything very carefully, and finally I assembled the pieces back together. When I tried to turn on the printer again I received the same Error message and all the leds blinking.
    I've been looking for a service manual on the web or something to solve this, but I was unable to achieve my goal. I can not indulge me and buy another printer, I can not reach HP customer service, and nobody knows how to fix this problem here. Moreover I feel like I have a little kind of affection for this appliance.
    Now my question: is this problem fixable? Can I fix it on my own?
    Thanks a lot in advance.
    CULEBRA83

    All lights blinking on the printer would indicate a fatal error situation. Here are couple of things you can try:
    1) Perform the steps under the section 'All lights are Blinking' in the document below:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00476152
    2) Follow the steps in the document below to 'Clean the gold-colored contacts in the print carriage' and cartridge contacts.
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00094661
    Note: Ensure that the printer is disconnected from power while performing the step.
    Hope this helps.
    Say thanks by clicking the Thumbs up icon in the post
    Please mark reply as "Accept as Solution" if it solved the problem, so others can find it.
    Although I am an HP employee, I am speaking for myself and not for HP

  • Green and Orange LEDs blink after each other - what does this mean?

    It won't show up in iTunes, it won't show up in Windows Explorer, and it won't show up in My Computer. Everything else is fine, but it keeps saying "USB Device Not Recognized."
    What should I do?

    If it helps, when I plug the shuffle into the PC, a balloon appears that reads, "USB Device Not Recognized."

  • Power Light Blinks after firmware update to 1.00.17

    I have model # WRT54GX4.
    It has worked great, i just wanted to update the firmware.
    I updated the firmware from 1.00.15 to 1.00.17 and now the power light just blinks.
    Based on what i read it sounds like the firmware needs re-loaded because it could be corrupt on the router now.  It could have been the way that i upgraded.  i was in wireless mode when i did the upgrade thru the web utility, mayby i should have been plugged in.  The other thing is that i use 192.168.1.X range (not 192.168.0.X range), i am not sure if the firmware upgrade changes the ip back to 192.168.1.1, which affected the upgrade.
    In either case my power light is blinking.  i also tryed to hold the reset button for 10 seconds, i also tried 30.  After that i plugged directly into the router from the pc using a regular patch cable.  I change the ip on my machine to 192.168.1.8 and the subnet to 255.255.255.0 to match the router.  i am assuming that the router is reset to 192.168.1.1 now that i pressed the reset button.  After doing all this i get a network connection, but i cannot ping 192.168.1.1. 
    Here is my other question.   To fix the issue i would think that i would have to run the firmware upgrade utility from outside the router, now that the router is not accessible.  But the download page does not have a firmware utility like the other models.  The instructions want you to use the web utility on the router.
    Please help.

    HI,
    u can upgrade the router from the "outside" using the tftp utility available at ftp.linksys.com/pub/network/tftp.exe .
    however you first have to be able to ping the router....reduce the NIC speed to 10Mbps...assign a static IP to your PC ...reset the router and then try to ping....once the ping is confirmed....you can upgrade the firmware.
    and yes the default router IP should now be 192.168.1.1

  • Iomega StorCenter ix2 white LED blinking after fw update

    Hi,
    today I tried to update the firmware of my ix2, don't know if it is the ix2 dl as the case looks like this http://shop.lenovo.com/de/de/servers/network-stora​ge/lenovoemc/ix2/ but with StorCenter instead of ix2-dl written on the front. As Version 3.3.2.24208 was installed, I manually uploaded ix2-ng-3.3.2.29823.tgz as a first update step to be able to update to 4.0.6.19294  in the next step as recommended in the FAQ. 
    see https://lenovo-eu-en.custhelp.com/app/answers/deta​il/a_id/31178
    But after successfully deploying the new firmware and the automatically reboot, the device sticks to a glowing blue HDD LED and a blinking white power LED. I read about the chance to boot from an USB flash drive but I can't find the image to prepare the USB flash drive.
    Can you please provide me with this image or tell me what I can do to access my device again?
    Thanks.

    You can put the serial number in the box under "Find Your Product" to see if it is in warranty still. If you still have the original purchase receipt, you can contact technical support and they will update the warranty if it is still within the warranty period. Unfortunately, only technical support can provide the link for the imager as you have to sign a non-disclosure agreement.
    Have questions and need answers?
    Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
    LenovoEMC Support & Downloads
    LenovoEMC North America Support Contact Page

  • WRT54G2 3 and Internet LED blinking

    I have a WRT54G2 v1 router.
    When power is attached the 3 and Internet LED are blinking. None of the other LED's are blinking.
    No other cables are attached to the router, just the power cable.
    Downloaded the latest firmware, set a static IP address on the laptop, attached a ethernet cable from the laptop to the router but cannot ping or get access to the router to update the firmware.
    Need suggestions as to what the 3 and Internet LED blinking means and what else I can try.

    Here is the latest and this will be done...
    I got back online (without the router, just direct connect to ISP with modem). Did a online CHAT at linksys.com/support. I asked the individual if the blinking LEDs were some sort of diagnostic code. He had never or could not find anything that suggested the blinking 3 and internet LEDs meant anything.
    So the Individual stepped me though the following (common set of steps with all I will assume.)
    No other cables are plugged into any of the router ports.I tried to reset the router. Held the reset button for 30 seconds... no change in which LEDs were blinking (still the 3 port and internet LEDs). Nothing happens with the power led.
    Held the reset for 60 seconds... no change.
    Held the reset button and plugged in the power supply, waited 30 seconds to release... no change.
    Held the reset button and plugged in the power supply, waited 60 seconds to release... no change.
    Asked me to plug in another power supply... could not do that, the router only came with one power supply.
    Asked me to connect router to a computer, step through process to setup static ip address.. attempt to ping router... nothing (was not getting a link light on the computer network card.)
    Finally said I would have to call customer service to get a RMA.
    Called customer service, was told to access the linksys.com/support and use the warranty online system to request a RMA.
    Went online, got to the RMA request, wanted a Case #. No one gave me one, had to call back and get one, they had me talk with a technician. Support person wanted me to go through the same process that I had gone through the night before.
    Explained that went though it already, they had to talk with a supervisor.
    After several minutes came back and gave me a case #.
    Back to the online RMA request - case # was not valid.
    Called customer service back again, after another discussion, was given a new case #. This person did stay online and waited as I went through each step in the online RMA process.
    SO long story... unit shipped back to linksys, replacement being shipped to me.
    (Mod note: Edited for guideline compliance. Thank you for your understanding.)
    Message Edited by giantherockstar on 08-26-2008 10:30 AM

  • SG200-08 all LED blink together.

    Hello,
    I have a SG200-08 which all LEDs blink together. This happened after a firmware upgrade.
    I can not access my switch.
    does anyone know a solution for this?
    thanks.

    Hi
    I think the following link will be helpful to upgrade and after upgrading the firmware, reboot the switch to factory default settings. I tried and I was successful, so I though it would be helpful to you.
    The following link will be useful while upgrading :
    http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=4&app=search&vw=1&articleid=947
    Thanks & Regards
    Punith Kumar Neelam
    SBCD Engineer

  • TS1538 Device not recognized in iTunes for Windows  I wasted about 1.5 hours with Apple on this issue. It all started happening after I updated to the latest version of iTunes. I haven't been able to sync my iPhone 4 in 1 month and am freaking out about p

    Device not recognized in iTunes for Windows
    I wasted about 1.5 hours with Apple on this issue. It all started happening after I updated to the latest version of iTunes. I haven't been able to sync my iPhone 4 in 1 month and am freaking out about possibly losing my pictures, video, text messages and music.
    Windows XP user.
    Any help will be greatly appreciated.
    iPhone 4, iOS 5.1.1

    If might be helpful if you actually told us what the problem is.

  • I have Adobe Acrobat 9 Standard on both of my computers.  Some time ago, one crashed my computer and I had to reinstall the operating system and all applications.  After I had installed once Acrobat 9 Sdt in the computer, I wanted to update the software v

    I have Adobe Acrobat 9 Standard on both of my computers.
    Some time ago, one crashed my computer and I had to reinstall the operating system and all applications.
    After I had installed once Acrobat 9 Sdt in the computer, I wanted to update the software version 9.0.0 update to the same level as it was before the crash and that the other computer has version named 9.5.5.
    The system for update from version 9.0.0 does not work at all. "There are no updates" listed in the dialog.
    Can you advise how I get my Adobo Acrobat 9 Standard (Version 9.0.0) could be updated to the same level as the computer had before the crash.

    ftp://ftp.adobe.com/pub/adobe/acrobat/win/9.x/

  • Firefox has been crashing all the time after I updated to the newest version. I tried to uninstalled firefox and all addons. Restarted the computer to reinstall Firefox and it's still crashing all the time. Please help.

    Firefox has been crashing all the time after I updated to the newest version. I tried to uninstalled firefox and all addons. Restarted the computer to reinstall Firefox and it's still crashing all the time. Please help.

    https://support.mozilla.com/en-US/kb/Firefox%20crashes#w_get-help-fixing-this-crash
    Type '''about:crashes''' in the URL bar and hit Enter. <br />
    Click the hyperlinks to bring up the Crash Report pages and copy'n'paste the URL of each of those reports into the message box here. We'll see if we can help you figure out what is causing those crashes to happen.

  • MacBook Pro Won't Boot after Firmware Update

    So I just upgraded to a MacBook Pro which came in the mail yesterday. I removed the Apple-installed HD and swapped it out for a bigger, faster HD. I installed OS X from scratch, imported everything from my Time Machine backup during the Setup Assistant, and then started installing updates. Everything was running swimmingly until the last updates.
    What happened is when I rebooted my MacBook Pro and logged in after a series of updates, I got presented with both a Bluetooth update and a Firmware update at the same time. Both required a restart so I thought I would kill two birds with one stone. I installed the Bluetooth update, and then when it asked to reset I installed the Firmware update instead. However, the firmware update didn't behave as advertised because instead of shutting the MacBook Pro completely down, it restarted and then started installing the firmware update.
    Ever since the firmware update (which I think installed correctly but don't know how to verify), I cannot boot my MacBook Pro. Using the OS X install DVD I can view my firmware version using System Profiler, and the number it is reporting is MBP53.00A.B03.
    I have tried booting in verbose mode to try and get a feel for the problem, and it eventually hangs on an infinite loop saying something about not being able to find something on disk0s2.
    I also thought I would fix the problem by doing an Archive and Install, but it quit at the very beginning of installing with the error "unknown error".
    Also I thought I would format the disk with Disk Utility and then try installing again, but Disk Utility reports that it in unable to unmount the volume.
    Any help you can provide would be greatly appreciated. Thanks!
    -- Update --
    Remember how I'm unable to unmount the drive? I force unmounted it and then used Disk Utility to repair the volume, but still no luck.
    I think the key to the problem is this new HD I put in runs at 3 Gbps. I think I read somewhere that the new MacBook Pro's don't support that.
    I think next I should try swapping out the new HD in my MacBook Pro with the one it originally came with. What do you think?

    I, too, have a brand new MBP 15" that I put an Intel X25 in. At the 1.5 (Prior to Firmware Update) setting, it worked fine. I rant the Firmware Update, all looked fine, but the drive is no longer able to be seen.
    Flash the PRAM, per other suggestions to no avail. Boot off of the DVD and disk utility nor Profiler sees the drive.
    Replace the drive with the stock that came with the MBP (which I had never even used) and it works.
    Put the Intel X25 into a Windows machine and it works fine. Reformatted it (in windows) and put it back into my MBP. Still not able to see it (from the Disk utility after booting off the DVD).
    Intel's firmware for the drive says its up-to-date (new drive) and if I attempt to "re-run" the Mac Firmware Update, it says that the machine is already up-to-date.
    Seems odd that it worked before an now it doesn't. Also seems odd that the X25 works in other machines. And that my MBP works just fine with the stock Hitachi 7200 320GB drive.
    Ideas? Intel says to call Apple Support. Not sure what I can say to them.

  • Restoring after firmware update - Ways :)

    Hi All,
    Nowadays we are receiving quite a few complaints that customers are unable to restore the application after updating their firmware.  I would like all to discuss to come up with some ways to restore their applications after firmware update.
    Before updating firmware
    Customer can backup his phone using Nokia PC Suite's Content Copier application.
    He can store his Contacts and Messages using Nokia Communication Centre as .csv file or .txt file.
    For his Contacts he can sync with pc suite supported sync applications.
    Messages he can store in Memory card and he can make a backup of memory card in PC.
    If he is using Nokia PC Suite for his Multimedia items he can use Image Store if he is using Nokia PC Suite or Nokia Photos if he is using Nokia OVI Suite.
    For Music he can use Nokia Music Manager or Nokia Music.
    Once after updating his firmware, if he is unable to restore he can get those from above said applications.
    If his calendar entries are not restored(as in case of some of Nokia e 71s and Nokia N 95/95 8 GBs), for God's sake if he has got one more similar device(or device having switch application on phone), he can restore the backup file to another phone having switch application, then he can transfer his data (Contacts, Calenders etc ) to his original phone
    Dear Forum members, if you have got any other work around please let me know regarding the same, which will help our customers

    Hi,
    If you have issue in Nokia PC Suites, [subject to your phone's compatibility with Nokia OVI Suite 2.0.0.10 ],
    you can install Nokia OVI Suite 2.0.0.10 and check if you can take backup and restore it later.
    Also i would suggest to use USB for taking backup, since it will be faster than Bluetooth.  Also you can select one category at one time(say backup contacts alone, then Calendar, then messages etc and so on ....)
    Its better to skip memory card backup while backup-ing other Phone data for faster backup.  Memory card backup can be done separtely(since it wont be affetcted while updating firmware, users can safely remove memory card while updating firmware)
    Nowadays though recent phones has got UDP(User Data Prevention i.e., even if you update your phone's firmware, your data wont get erased ), still it is recommended to backup your phone data.
    Hope this could help
    I welcome our experts to add more details related to this topic.

  • Problems after firmware update 52.0.007

    Hi,
    I got my phone back after the shop fixed a problem and updated the firmware to the latest version 52.0.007.
    But now I have following problems:
    I can't get the calendar anymore to show up on the homescreen, even after checking the checkbox to do so
    The Radio app. is gone
    Does anyone has a solution for this?
    Iwan

    It may sound crazy but sometimes you need to "hard reset" device after firmware update (beware all data erased) by keying in *#7370# followed by 12345 (default Nokia lock code unless altered by yourself). Sometimes UDP = User Data Prersevation feature of 5800XM can carry over corrupt entries when updating.
    Happy to have helped forum with a Support Ratio = 42.5

  • Data recovery after firmware update

    Hi guys,
    does anyone know it it is possible to recover data after firmware update in N8? some data are preserved (videos) and some are lost (photos).
    thx.

    if you didn't backup them, there is no way to recover them
    Greece Nokia X6 RM-559 v40.0.002

  • TS1538 This is useless - it all started happening after I updated to the latest version of iTunes

    Device not recognized in iTunes for Windows
    I wasted about 1.5 hours with Apple on this issue. It all started happening after I updated to the latest version of iTunes. I haven't been able to sync my iPhone 4 in 1 month and am freaking out about possibly losing my pictures, video, text messages and music.
    Windows XP user.
    Any help will be greatly appreciated.

    If might be helpful if you actually told us what the problem is.

Maybe you are looking for