WRT120N no IP Address after reset

Hello,
I am a DSL internet user and has been using WRT120N (Wireless Modem) attached to my DSL router for a year with no problem.
Until recently when I powered down and powered up, (which I do every so often when access is not in use) , my model is not picking up a valid IP address.
I've pinpointed my wireless modem as the culprit since if I cannect a LAN cable from the DSL router to my computer, it works just fine.
My wireless router stopped working and ipconfig does not show 192.168.1.1
Instead, on commnad line prompt it only this shows:
AutoIP config shows 169.254.190.144
Subnet mask: 255.255.0.o
The rest of the fields are 0
I tried to do a hard reset to factory setting and it is still the same.
Any suggestion?

I agree with kawal. Also make sure the computer is connected to the Ethernet port not to the Internet port of the router. Make sure the power adapter is correct. Reset the router again. If you are still not able to get a valid IP address, set a static IP (IP: 192.168.1.5 Default Gateway: 192.168.1.1 Subnet: 255.255.255.0) on the wired computer and perform a TFTP upgrade.
Assigning a static IP address on a wired computer
Upgrading the router’s firmware using the TFTP utility

Similar Messages

[SOLVED] How to unload any driver(dll) at the start up after reset??

Dear Developers,
Greetings!!!
As, I am using AM335x BSP with WinCE 7. We have one vendor Wifi device and its binary images(driver installer). When we reset the target board, the modules do not reset and during the time of board booting, I found the following logs
7771 PID:400002 TID:9e0006 Warning! Kernel DLL 'rwlpsdio.dll' is registered for thread creation/deletion notification. To improve performance if you dont need thread notifications call DisableThreadLibraryCalls from inside D
7774 PID:400002 TID:9e0006 DriverEntry!!!!!!!!!!!!!
7777 PID:400002 TID:9e0006 SDIO not initialized, returning!!!!!!!!!!!!!!
7778 PID:400002 TID:9e0006 OSAXST1: <<< Unloading Module 'rwlpsdio.dll' (0x9E438000) at address 0xA7C90000-0xA7D47000 in Process 'NK.EXE' (0x87FDFAD0)
PB Debugger Unloaded symbols for 'rwlpsdio.dll'
We conclude that when we reset the device, the driver is not unloading and that why, its not releasing the resource.
My motto to solve the issue by creating an application that run at every startup after reset and unload the driver. So, that during the time of loading it, it re-loads properly..
I am searching it on google but unable to find any way so far.
ASAP reply must be highly appreciated

Dear Developers,
@balaji,
As I had read the link https://social.msdn.microsoft.com/Forums/en-US/98aa5eca-0b38-4f6e-bf7b-81cb7068422e/sdio-wifi-driver-and-prefetch-aborts-problem?forum=winembplatdev
And, in the above thread you were replying as
Hi Misbah,
NdisMRegisterMiniport sure needs to be called from DriverEntry. Can you check if NdisRegisterAdapter is present. This ideally should be somewhere in your stream interface.
I am taking a wild guess here , perhaps you can may be introduce some delay in DriverEntry , so that the stream driver gets a chance to load?.
e.g. you can use one of NdisWaitEvent functions.
All the best.
Regards,
Balaji.
As, per my knowledge, the DriverEntry is the first function that is called by ndis after loading the ndis.dll and it is responsible for registering the driver with NDIS by using
NdisRegsiterMiniportDriver.
Any how in my case, DriverEntry is called but the same function we are getting one error and that's why driver is not registered with NDIS.
We are checking SDIO interface status, either it is uo or not. If it is up then fine and if not then display warning and unload the driver.
So, in my case, the SDIO status is not up after resting the device.
Any suggestion will be appreciated????

Exit or Badi to block document after Reset Cleared Items in FF.5

Hi,
When you run FF.5 and some rejected documents are returned by the bank, I have to block the document after reset cleared items with a especific payment block key.
Anyone already done something similar?
Tks!

Hi Rao,
<b>Userexits</b>
VMDE0004     Shipping Interface: Message SDPACK (Packing, Inbound)
VMDE0003     Shipping Interface: Message SDPICK (Picking, Inbound)
VMDE0002     Shipping Interface: Message PICKSD (Picking, Outbound)
VMDE0001     Shipping Interface: Error Handling - Inbound IDoc
V53W0001     User exits for creating picking waves
V53C0002     W&S: RWE enhancement - shipping material type/time slot
V53C0001     Rough workload calculation in time per item
V50S0001     User Exits for Delivery Processing
V50R0004     Calculation of Stock for POs for Shipping Due Date List
V50R0002     Collective processing for delivery creation
V50R0001     Collective processing for delivery creation
V50Q0001     Delivery Monitor: User Exits for Filling Display Fields
V50PSTAT     Delivery: Item Status Calculation
V02V0004     User Exit for Staging Area Determination (Item)
V02V0003     User exit for gate + matl staging area determination (headr)
V02V0002     User exit for storage location determination
V02V0001     Sales area determination for stock transport order
<b>Business Add-in</b>
DELIVERY_ADDR_SAP     Address Change in Delivery Processing
DELIVERY_PUBLISH     Announcement of delivery data during database update
Reward pts if found usefull
Regards
Sathish

Connect Software won't connect to router after resetting router on any of my computers

I had to do a reset of the router. I have done it with the button on back and through the web based interface. I have followed all directions on uninstalling connect after restarting the router. I get an error that says it does not know if it is connected to the internet.. Well it isn't. I have tried numerous times and the connect will not install. I would like to get it back the way it was when I originally installed it. The key does remember the admin and password but it only allows me to get to the web based interface.
I have tried everything I know to get the key to work again to no avail.
Could someone please tell me what I am missing when I try to use the connect software after resetting the router?
Thank you so very much!!!!

So as per the concern you mentioned that Cisco Connect Software won't connect to the Internet after resetting the router... So could you inform us the model number of the Router that you are using it in the Network...
As well as please inform us that who provides you Internet means who is your ISP ( Internet Service Provider ) ? Check if you can go online from the modem connected directly to the computer... If you can browse the Internet then check whether there is any manual IP address given to your computer or not...

Delete primary email address and reset to use the ...

How can I delete the primary email address and reset to use the second email address?
Because I cannot remember the password (always used automatic sign in option) and I no longer have access to the primary email address.
Now I cannot sign-in to my skype account from any other computer. I do not want to loose the skype account as I have many phone numbers and contact information saved.
Thank you and Merry Christmas

if your account has a billing or purchase history in the last 6 months, you can request for a new password without the need of your registered email address. just click the link below;
https://login.skype.com/account/password-automation
Then after you reset your password, you can change your primary email address.
IF YOU FOUND OUR POST USEFUL THEN PLEASE GIVE "KUDOS". IF IT HELPED TO FIX YOUR ISSUE PLEASE MARK IT AS A "SOLUTION" TO HELP OTHERS. THANKS!
ALTERNATIVE SKYPE DOWNLOAD LINKS | HOW TO RECORD SKYPE VIDEO CALLS | HOW TO HANDLE SUSPICIOS CALLS AND MESSAGES
SEE MORE TIPS, TRICKS, TUTORIALS AND UPDATES in
| skypefordummies.blogspot.com |

After resetting router

I couldn't get my IP address to be recognized, so I pressed the reset button on the router. Now I can't even get a signal on my computer. What do I need to do after resetting?

It sounds like you did reset your router and now you have to reconfigure the router for your connection. With a hard wired pc open your browser and in the address bar type in http://192.168.1.1 and hit enter. This will open a window asking for a user and password. Leave the user blank and type in admin as the password. That will get you in to the web-based set up of your router. Configure the router for you connection then set the SSID to something other then linksys so you can identify your wirless when you connect your wireless pc/devices. Make sure broadcast SSID is enabled and set up what ever security if needed. Then connect you wireless pc with the information you enterd in your router.
Richard Aichner (Ikester)

Pcie re-enumerate fail after reset

In my V7 FPGA image there are several PCIE switch devices and 1 PCIE
endpoint device. I attach it on a Linux x86 laptop. When the system start
normally, the hierarchy and the bus:device.function number are :
           SW0(05:00.0)
            |
|                                       |
SW1(06:00.0)          SW2(06:01.0)
|
EP (08:00.0)
When I assert a whole chip power on reset. The devices are re-enumerated.
But the hierarchy may change. Some time they are identically the same with
the normal ones.But sometime I saw the bus number of SW1/2 has changed and
the EP failed to be enumerated. The hierarchy is like:
           SW0(05:00.0)
            |
|                                              |
SW1(0B:00.0)          SW2(0B:01.0)
|
(missing EP,the
secondary bus number
of SW1 is 0xD)
The EP was missing because the HOST didn't send CONIG RD/WR to 0D:00.0
after it set the secondary bus number of SW1 to be 0xD.
Can anyone help me to give answer to the following questions:
1. Why the bus driver/HOST assign 0xB to the secondary bus number to SW0
rather than 0x6 after reset?
2. Why the bus driver/HOST didn't send CONIG RD/WR to 0D:00.0 to proceed
the enumerate?
BWT: On MS windows system the re-enumerate is always success with
unchanged hierarchy after reset.

Hi Anthrol,
For the BUS:Device, enumeration - if you look at the tree, the 2 switches are on the same tree level, and are this considered on the same "BUS". If these were Peer-to-Peer capable, they would simply be different devices on the same level.
For the re-enumeration, you would need to look into that with the Linux driver controlling the root -- that is responsible for enumeration. You are correct, if the part never receives a new BDF, it won't appear in the device tree, and anything the Root addresses to BDF 0D:00.0 will be discarded by the switch as URs (Unexpected Requests).

WRT54G IP lost after reset router

After reset my WRT54G router, I seem to cant find my IP address.is it because my firewall in my company is set to 192.168.1.1.before this, my WRT54G IP is set to 192.168.1.109.Is there any way to find the IP. I am using a desktop to configure the router,so no wireless connection.
forget to say, the wrt54G is not my PC default gateway, is it connected to the same switch same with my desktop PC.
Message Edited by nearownkira on 01-05-2009 05:30 PM

Who is your ISP ? What IP have you lost ? Could not understand your concern...Please explain in detail...

My husband gave me his iPod touch, even after resetting all settings, and even though I have a user name and password whenever I need to update apps it shows his previous user name, and is asking for his password. How do I fix that?

My husband gave me his iPod touch, even after resetting all settings, and even though I have a user name and password, whenever I need to update apps it shows his previous user name, and is asking for his password. How do I fix that?

dom59 wrote:
Ok, when I go into my Apple ID account, everything looks right. It does show my user name. It's only on the iPod that it shows my husband's previous user name, and it asks for his password. Everything in iTunes and my account looks right. The issue only seems to be with the actual device, iPod Touch 4th gen.
There is more than one way to access the Apps Store and the iTunes store. One is via iTunes on your computer, and the other is via the apps on your iPod.
Just because you are logged in on your computer does not mean you are logged in on your iPod.
The reason your husband's user name comes up is because he was the last one to log on. You can change that by going to Settings>Store. Tap the Apple ID, Tap Sign Out, Tap Sign In, Tap Use Existing Appel ID, enter your e-mail address and Apple ID password, and tap OK.

External Display resolution problem after resetting PRAM

Gello, I've got Fujitsu-Siemens P19-2 monitor hooked up to my MbookPro and after resetting PRAM the correct display resolution disappeared from the "Displays" menu in System PReferences.
So did the refresh rate option...
What do I do?
I really need to change the refresh rate and the resolution, but the refresh rate button is grey and unclickable, and the resolution simply isn't there (I need 1280x1024).
REsetting PRAM and SMC didn't help.

After a couple of resets everything went back to normal

Even after resetting apple id password still won't activate my phone

I did a reset erase all contents and settings but i'm stuck at activation lock! The iphone is mine and email is correct but even after i reset my password, IT STILL WON'T ACCEPT THE NEW PASSWORD :(( please help! Thank you.

moniiice
Re: Does reset all content and settings automatically sets Find my iphone off?
Jan 27, 2014 8:54 AM (in response to KiltedTim)
But when i sign in my icloud account on the activation lock, it still won't accept it. Even if i tried resetting my password. I believe that i use the right icloud account but still it won't activate it. I tried locating my device on find my iphone and the device was not there, does it mean my device has already been erased?(i resetted all content and settings) but why does it still have an activation lock after reset? Tried everything but still no luck :( reset apple id or password but still nothing :(

I downloaded ios7 and now some apps won't open even after resetting them. Don't won't to lose my info by deleting them and starting over. What to do?

I downloaded ios7 and now some apps won't open even after resetting don't won't to lose my info by deleting and starting over.. What to do?

Try close all inactive apps
1. Double tap the home button to bring up the multi-tasking view
2. Swipe up on the screenshot of the app you want to exit.
3. The app will fly off the screen

Hi. I tried to change my old icloud account on a new one. After reset the settings I need to enter my old Apple ID account and password, that I don't remember.

Hi. I tried to change my old icloud account on a new one. After reset the settings I need to enter my old Apple ID account and password, that I don't remember.
I do not remember it because when I bought the my iPhone 4s in 2011 I didn't understand how it works and asked a representative to set it up for me. The representative helped me and gave a piece of paper with login and password but I lost it a long time ago.
Before resetting the settings I turned off "Find my iPhone" function, but it anyway asks me to enter my old Apple ID and password. I have the original box, documents, receipt. So how can I solve this problem?

You do not have to call US, but you need to call. Or else.
Contact Apple for support and service - Apple Support

I am unable to set up my iphone 5 after reset since am getting a error stating 'unable to reach server' . i tried restoring the same from my computer but i get a error stating server unavailable' . please help me as my phone is stuck at the set up page

i am unable to set up my iphone 5 after reset since am getting a error stating 'unable to reach server' . i tried restoring the same from my computer but i get a error stating server unavailable' . please help me as my phone is stuck at the set up page. so i have already tried recovery mode as well.

Contact Apple support for warranty service.

After reset Mail hangs w/spinning ball on "Reading table of contents"

This problem is on a 17" monitor Power PC G4, 256mb DDR SDRAM.iMac, half ball bottom, with Mail, with Systems 10.3.9
After Reset, Mail is hanging with the spinning beach ball on "Reading table of contents." Quite a few emails are being retrieved and placed in the Dock before the hang, and Mail responds to mouse commands up to the "hang." Then a Force Quit is the only way to proceed. Other programs run OK, with Mail "hung."
The reason for the Reset is that my daughter reads "fan fiction," and can go through a hundred pages in an hour, and the computer gets so plugged up that it takes FIVE MINUTES to retrieve, then display another Safari window. Empty Cache does not help. So, to get things back to normal, a reset is required. Something went wrong on this reset.
This happened once before, possibly with OS-X 10.2, and I was advised to delete a file somewhere deep in Systems, and Mail apparently made a "new" file and all was fine from then on. My "guess" is that Mail then makes a new "table of contents."
Anybody know what file to delete? Or any other advice? At the moment, I am getting Mail with another IMac, with System 10.2
iMac 17" "half ball bottom" 1 GHZ PowrPc G4 Mac OS X (10.3.9)

Hello Jean.
When you use the term "reset", are you referring to a
computer restart?
On this PowerPC with 10.3.9, what is the hard drive
capacity and available free space?
If the problem Inbox mailbox is for a POP type
account, with the Mail.app quit and using the Finder
go to Home > Library > Mail > this account named
folder (named by the user name and incoming mail
server for the account) > INBOX.mbox.
Move the INBOX.mbox to the Desktop.
Launch Mail and if successful, a new (and empty)
INBOX.mbox will be created automatically by Mail
within this account named folder when receiving the
next message with this account.
This should allow the Mail.app to function properly
again while working on the old INBOX.mbox move to the
Desktop to recover the existing messages.
Control-click on the old INBOX.mbox moved to the
Desktop and at the menu window that appears, select
Show Package Contents.
List the package content file names and size of
each here.
I have had the same problem as Jean - did what you advised and now find mail runs find but need to rescue the old mail.
This is the package content of my old inbox:
content index 36 kb
content_index-computername.local-372 10.9 MB
info.plist 4 kb
mbox 939.1 MB
tableofcontents 1.5 MB
hope you can help me...
x
habibi

WRT120N no IP Address after reset

Similar Messages

Maybe you are looking for