WRT120N working firmware version 1.04

try this version for firmware version WRT120N. 1.04 is working my laptop msi and desktop....
hope you can help on this....
http://downloads.linksysbycisco.com/downloads/firmware/1224646102739/FW_WRT120N_1.0.04.002.bin

I have exactly the same setup and SD card as you, and I see 10MB/s pretty consistently. Maybe a little more. 12MB/s for short periods. I haven't used the SD card copy on firmware 1.04.06 yet though. I have always used firmware 1.03.13 up until now. Some time back someone who pulled their MPW apart concluded that the SD card reader is actually a USB 2 device, and is connected to the MPW main board using a USB 2 chip. If that is correct, and it seems likely, then I don't expect any significant speed increases above that. USB 2 should support 60MB/s, but in the real world it usually only supports a sustained speed of 20MB/s. Also, the MPW does some sort of validation of the copy, as we would want it to, which means it doesn't do a straight copy, but Reads-Writes-ReadsBack-Verifies. So a maximum speed of 10MB/s makes sense. What doesn't makes sense is creating a wireless plus USB3.0 hard drive for on the road backups, and using a USB 2 card reader and associated chip. It is a bit of a fail on WD's part.

Similar Messages

WRT54G, Firmware Version: 8.00.2, Stops routing after a day, Requires Power Cycle to Work Properly

WRT54G, Firmware Version: 8.00.2, Stops routing after a day, requires a quick 10-15 second power cyc... work properly for a day or so before powering down again….
I was using for years the BEFW11S4 Model without any issues before it finally failed. Due to loyalty, I went out over a month ago to purchase the current model. The problems did not pop-up until month of December… The issue had me thinking at first was the internet connection…
Any advice on dealing with this issue… Is it a Software and/or Hardware? It appears to be a software related condition…
For those other WRT54G users that appear to be having similar issues, regardless of the firmware, it would appear we all seem to be facing the same condition of resolving the issue after a power cycle…
Is there anyone out there that has already resolved this issue (e.g. Configuration changes)? Does anyone have input that Linksys is actively working on this issue?
Although I am sure we will find a solution, having to cycle the power is a bit disappointing since my older model had no such flaws with my current internet connection…
Thanks for the support out there….

If you have an Intel wireless card you can try this. I came across this link on the forum a days ago and it seems to help. The problem is that my problem was much more intermittent than some people are experiencing. It mainly seemed to appear when undocked the computer or if there was a power outage during the day. I would be interested to see if it works for you or if I'm just chasing my tail. I've seen other suggestions for changing the thresholds in the router which may be related.
http://www.intel.com/support/wireless/wlan/sb/cs-006205.htm

Problem with restore.I have a 2 gen running firmware version 4.2.1

Hello there !
Hopefully some smart persons here will be able to help me. First it has been awhile since i used my itune store because i didnt needed to and did a format of my computer after the last time i used it..so i had to upload my library etc and start from scratch. I downloaded a couple new games,everything was working fine..then when it came the time to sync and put these games on my ipod touch 2 gen the installation failed. I retried again and it keeps failing again and again so i choose to do a restore on it and expecting the problems would be solved. Problem wasnt not solved at all and it said an error (6) occured and i have the image on my ipod of the white cord trying to connect to itune store.
Restore doesnt work at all and it seems like my ipod is totally useless as i cant use it anymore. I did the diagnostic..it said no ipod were found. I also did the check up thing for the technician so ill paste it here maybe it will give some clues..
I have this error now as well... No iPod, iPhone, or iPad found. It also said secure link to itune store failed..not sure if these are all related to the same problems or all different at all..im clueless and need a generous soul to help me out.
Thank you tons for the help !
@Edit : Even with my other 2gen ipod i cant install these new games,it keeps failing as well..but at leasnt i havent done Restore on it yet and i fear to do it for reason you guys can guess.
Microsoft Windows 7 x64 Ultimate Edition Service Pack 1 (Build 7601)
System manufacturer System Product Name
iTunes 10.3.1.55
QuickTime 7.6.9
FairPlay 1.11.17
Apple Application Support 1.5.2
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.1.2
Apple Mobile Device Driver 1.57.0.0
Bonjour 2.0.5.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes Serial Number 00AAB2F80F513CD0
Current user is an administrator.
The current local date and time is 2011-07-17 18:45:37.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 9500 GT
**** External Plug-ins Information ****
No external plug-ins installed.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name:     {B00FE55A-1662-4EE9-B880-6B076869B9F8}
Description:     Contrôleur Atheros L2 Fast Ethernet 10/100Base-T
IP Address:     192.168.2.10
Subnet Mask:     255.255.255.0
Default Gateway:     192.168.2.1
DHCP Enabled:     Yes
DHCP Server:     192.168.2.1
Lease Obtained:     Sun Jul 17 17:51:16 2011
Lease Expires:     Wed Jul 20 17:51:16 2011
DNS Servers:     192.168.2.1
Active Connection:     Connexion réseau
Connected:     Yes
Online:          Yes
Using Modem:     No
Using LAN:     Yes
Using Proxy:     No
SSL 3.0 Support:     Enabled
TLS 1.0 Support:     Enabled
Firewall Information
Windows Firewall is off.
ZoneAlarm Firewall is installed.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was unsuccessful.
The network connection timed out.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was successful.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2011-07-17 18:43:19.
**** Device Connectivity Tests ****
iPodService 10.3.1.55 (x64) is currently running.
iTunesHelper 10.3.1.55 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Contrôleur d'hôte ouvert PCI vers USB NEC. Device is working properly.
Contrôleur hôte PCI vers USB standard étendu. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27C8. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27C9. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CA. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CB. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CC. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.
Most Recent Devices Not Currently Connected:
iPod touch (2nd generation) running firmware version 4.2.1
Serial Number:     9E01226F201
**** Device Sync Tests ****
No iPod, iPhone, or iPad found.

thats just rubbish ! i bought it secondhand for my daughter to use for music and apps, but its not compatible with anything, any suggestions other then throwing it away?

Will firmware version 4.1.7 automatically update to 4.1.9?

I recently upgraded to OS 10.3 from OS 10.0 on my Imac 700MHz G3. The installation documentation said that I would be prompted to upgrade the firmware if I needed to. I was not prompted so I went ahead and did the OS 10.3 installation. The firmware remained version 4.1.7f4 after the install.
Not too long ago I went through the same procedure on my Imac 400MHz DV. The only difference is that I started the upgraded process from OS 9.I, then to 9.2.2 using the updates (ending at the latest version of 9), then to 10.0, and then to 10.3. And finally updating with 10.3.9 combo to OS 10.3.9. During that whole process I never new about firmware and never checked to see what version I had before starting this process. After all of the above installations were finished I ended up with firmware version 4.1.9f1.
My concern is with the 700MHz G3 IMac. I'd like to update to 10.3.9 using the combo update but I'm concerned about the firmware. Will firmware 4.1.7f4 be updated automatically to 4.1.9f1 after the combo OS 10.3.9 is installed? Or should I erase the disk again and start over by first installing firmware update 4.1.9? Actually if that were the case I wouldn't be able to update my firmware since I don't have the correct bootable version of OS 9 on disk that is required for that computer. However my previous experience with the installations on the 400MHz DV suggests to me that that the firmware will automatically be updated. But I would like confirmation from the experts. I'd hate to spend all that time downloading and installing all of the latest updates (Combo 10.3.9, etc.) only to find that the firmware version is incorrect.
Thanks!
Al

Al,
I don't understand your anger. In your first message
you posted that you installed OS 9 and updated it to
9.2.2. So why don't you do that again on the 700 MHz
iMac?
I find it very amusing that somehow you see anger in my post. That is realy very funny! The reason I didn't just simply install OS 9 on the 700MHz Imac is stated in my original post. I would need a special (the original disk that came with this computer) bootable OS 9.1 disk to install 9.1 on this particular computer. However if there are retail 9.2 or greater disks available then that would work to. I own a retail version of 9.1 that I used for the 400MHz Imac. That wont work on the 700MHz Imac. So now I have to buy a another OS 9 disk. Thanks for your input. Al

Need a Script to Audit Firmware version of HP components.

Hi Team,
I am new to this portal, I am not sure if i have selected the correct board for this issue. If not please redirect thie thread to the correct team or guide me the link to the HP Blade system portal.
My issue:
We have 285 HP Servers, Where almost 275 are HP Proliant BL460 G7 & G8 Blades and the rest are HP DL380P and DL380 Standalone servers.
We recently did a HP SPP Update on all these machines and now for a reason we want to Audit if the component updates were correctly done by our engineers or not.
How ever for HP OS Components i have a script to Scan the registry and pull the Product version and match it to see if it has the Latest version or not.
But how do i do an Audit for the ILO'S of these machines and the Onboard Administrators and the HP Virtual connect if the firmware versions are correct or not ?
Is there any script or any Method to achieve this ?
We also have HP SIM tool as well, Can we do it form that? If yes then how ? Can any one please help in this ?

Frederik, After some tweaking and testing i was able to get it working, I haven't tested it via GPO as a startup script but standalone it is doing what i was after. I cant thank you enough for helping me on this as i had lost hope after days worth of intense
searching
Change that i had to apply ( space in a network path
was causing a "path not found error", Had to rename the "Office365 update" and update the path in Customconfig.xml or any other location that was pointing to "office365 update" )
set DeployServer=\\contoso\c2r\Office365 update\
REM Set ConfigFile to the configuration file to be used for
deployment (required)
set ConfigFile=\\contoso\c2r\Office365 update\Customconfig.xml
REM Set LogLocation to a central directory to collect script
log files (install log files are set in XML file).
set LogLocation=C:\AppData\Local\Temp

Firmware version is too high. How uninstall? Correct version where?

Help! That Firmware thing is driving me nuts. Wish apple would organize the latest upgrades by OS. It’s a maze.
My iMac DV (blue front slot loading) is OS 9.0.4 (I will upgrade but not right now, too long to explain).
I had bought a LaCie HD some years ago & made partition with OS 9.0.4, 9.1 to 9.2, it fell, bought another and installed it.
After much time I found out that to know my version of Firmware I have to look for boot ROM, my system profiler says it’s $0004.19f1 that means probably v 4.19.
If it’s v 4.1.9 it is too high it needs OS 9.1 and probably happened with I had OS 9.1 on my external HD. My LaCie CD Writer became a nightmare and I don’t dare to use it anymore, maybe it was because of the firmware ….or it might be that Apple CD/DVD Driver can’t exist at the same time as Toast extensions, it’s unclear to me.
Can’t find the latest firmware version for OS 9.0.4 that will work, or how I can take it off before I install another one. I know v2.4 will work on OS 9.0.4.
Got: Firewire v2.3.3 - usb v 1.4.2 - CarbonLib v 1.6 - Apple CD/DVD Driver v 1.3.5 player is v2.1
Help!
1. What’s the latest Firmware for OS 9.0.4?
2. Do I have Firmware v 4.1.9?
3. How do I uninstall Firmware v 4.1.9?
4. CAN Apple CD/DVD Driver exist at the same time as Toast extensions?
Thanks very much
Nicky

I think that you misunderstood Kappy's point about Mac OS X version.
What the information about OS X version is telling you is that those are the minimum requirements for the installer which places the firmware update permanently in the ROM on the logic board to run. However, once the firmware has been installed you are free to continue to update your version of Mac OS X for as long as Apple releases them.
I have an iMac G3 DV+ which has ROM version 4.1.9f1 and is running Mac OS X 10.4.8.
However, the firmware is backwards compatible as well. You obviously installed the firmware when you were running OS 9.1, but at some time regressed your OS to 9.0.4.
I think the issues that you are experiencing are related to other issues on your Mac. The folks in the iMac G3 forum should be able to help you sort that out.

WRT54GS V7 Firmware version?

Hi all! I've recently bought a WRT54GS V7 cable router/access point. Now, given the problems I've had with previous devices, I'd like to make sure that the firmware is completely up-to-date. However, when I go to the Linksys UK website, and find the product download page, I am asked which version of the device I have. I have version 7, but it is not in the list. Interestingly enough, when I clicked on version 6, and then looked at the firmware version details, it said something like "for version 5 only". My router seems to have version 7.50.0 firmware installed. Maybe this is the version which they all have, and there are not yet any updates available. Does anyone know? Thanks Michael

vness wrote:
Change the default country to US.
Well, I thought I'd tried that already (although it makes no sense to me - I bought the item in the UK).
However, when I look carefully, I notice that my location is being changed back to 'UK' whenever I try to navigate to the 'Technical Support' page. So this time, I've cleared my cookies, it works, and I can find the file.
Someone from Linksys might want to get around to updating the UK page, and sort out the location changer so it actually does change when you tell it to. I'm sure that I'm not the only person in the country to have bought one.
Anyway, thanks for the help, and for the quick response!
Michael

How to I determine the firmware version on my hp prime?

Friends
How to I determine the firmware version on my hp prime?
Thanks
Migs

The easiest way is: Home, Help, Tree, up-cursor, Enter.
Note: I don't work for HP. I'm just another happy HP customer.
-Joe-

WEBSITE BLOCKING ON WRT54G V6 (Firmware Version: v1.02.8)

Hello Friends,
Short: why some webpages block and others don't using this feature in my router? As mentioned above, I run a small office and am using an ::: WRT54G V6 (Firmware Version: v1.02.8) ::: router.
For instance, I have been successful in blocking sites such as "sex.com" and others. Also, in blocking sites by keywords such as: news, music, vid, nude, etc. BUT, when I try blocking FACEBOOK or TWITTER either by URL or keyword, guess what: IT DOES NOT WORK...!
Any ideas why this happens and how can I be successful in configuring this feature??? I will appreciate this! Blessings...
Solved!
Go to Solution.

Those sites have a random connection and DNS entries. Your best bet would be to use a DNS servcie like DDNS.com or OpenDNS.com service. Point your router to one of those DNS services and there DNS addresses, then set up one of those services to block FB and Twitter. If you use there DNS addresses on your router instead of the ISP DNS, and you block FB and Twitter, users should beable to get to FB or Twitter after that.

Need link to WRT16Nv2 Firmware version 11 please.

I recently purchased a WRT160Nv2 router with firmware version 11.
I had it configured to allow remote desktop connection to any of the 3 PCs.
PC1 3389 (External) to 3389 (Internal) on IP aaa.aaa.aaa.aaa
PC2 3390 (External) to 3389 (Internal) on IP bbb.bbb.bbb.bbb
PC3 3391 (External) to 3389 (Internal) on IP ccc.ccc.ccc.ccc
This worked fine.
However, I was having DNS issues that apparently were fixed in firmware version 15, so I upgraded.
And could no longer use the configuration above
As soon as I tried to enter the PC2 details (or PC3) it gave an error saying the port range was already in use.
I'm guessing that the firmware is not recognizing the different IP addresses and thinks the port 3389 is a duplicate.
After much searching, I found a link to firmware versio 8, which supposedly did not have the problems that version 11 has.
However, version 8 has the same issue as version 15 in not allowing the configuration I had.
Ande, after speaking to several online linksys chat people, and waiting patiently for a phone call from a tech, I do not have any link to firmware version 11.
So, if anyone happens to have a WRT160Nv2 with firmware version 11 still on it, and know some way to read the firmware out of it I would really appreciate it
Thanks.

Thanks for the link.
However, when I tried to register it told me my email address was banned (odd, since I've never been to that site).
Also, there is no contact information on the site for contacting the administrators so no way to get email unbanned in order to register to download the firmware.
I'm STILL waiting for the linksys tech to call, was supposed to be 48 hours from when I spoke to the tech online.
ldb.

How to downgrade my firmware version after a "succesful" update?

Dear Macusers,
Is there any way to downgrade my firmware version from 1.5.1 to a lower version? Even if my firmware update has been applied succesfully? I cannot use just the firmware restore CD because that is for an interupted or failed update.
Greetings,
Tim

Hello,
Many thanks for your reply. Yesterday I posted a topic about this problem with some more details. I hope this may help.
+"Since today my trackpad and keyboard doesn't response anymore. This problem started after I exit from sleep mode. Then I get a security form where I can enter my password, but I couldn't. So I restarted my macbook pro for about 5 times, removed my adapter and battery, but it doesn't work.+
+After that I went to iFactory and they said it is apparently because of my latest firmware update 1.5.1. But why does this happen a week after I installed this update? Anyway, he suggested me to downgrade my firmware version with a firmware restore CD. Well it sounded as an straightforward and easy solution until I read that the restoration CD doesn't work when the firmware update already has been applied correctly.+
+I have read some other topics about keyboard issues and some points are relevant for me:+
+I'm be able to use an external USB mouse and keyboard.+
+At system profile by USB, only my iSight, Bleutooth USB host controller and external USB devices are displayed.+
+The keyboard background light works properly+
+This problem happens all of a sudden without intervals or strange behavior.+
+Using Leopard (10.5.2) and Windows XP via bootcamp+
+I hope I can solve this problem really quick because I need my Macbook Pro badly for my study. Thanks in advance for studying my problem.+
Greetings,
Tim

What was the last firmware version for the Zen Micro before M

I would like to know what was the last firmware version for the Zen Micro before the MTP firmware?
Please make sure you are 00% on this.
Thankyou.

I think it does, but I'm not sure; since I wanted MTP, I only used .x firmware long enough to save the original Creative test files (with MediaSource, not ZMME) before upgrading to 2.x. And yes, I had to li've with 2..02's shorter battery life until 2.20.05 came out.
May I ask why you want to go back to .x firmware? The only thing that will get you is the ability to use it with Win98SE/2000/Me--but only if you can install Creative drivers on every PC you use it with. MTP requires WinXP SP or 2 and WMP 0, but doesn't need any Creative software at all to work. (Microsoft has made an MTP driver for Win98SE/2000/Me, but it requires customization and may not be supported by other software. I'm tinkering a bit with the customization part right now.)
There are other pitfalls in changing Micro firmware families, in either direction--you'll lose all the files on your Micro, you'll have to install a different ZMME (and I've heard non-MTP ZMME isn't quite as full-featured as MTP ZMME), and you'll need a new plug-in for MediaSource to work.

Firmware version explanation + sleep problem

My 10 days old iMac baby has problems to sleep. It goes to sleep but after 5-6 minutes it's awaken again. I tried everything I found relevant to this problem on this discussion board but no help at all. Mac baby was born with 10.4.8 and now it's at 10.4.10 - combo update, everything else is working perfectly well except this sleeping problem. I
After all, I went on Apple download in order to check if there are some EFI Firmware updates and now I'm more than confused with numbers.'
On Apple's site it's clearly written that the most recent firmware version for my iMac is "IM51.0090.B03 (20-inch late 2006)" http://www.apple.com/support/downloads/imacefifirmwareupdate11.html but my System Profiler shows higher number count: "IM51.0090.B08".
From System Profiler:
Hardware Overview:
Model Name: iMac
Model Identifier: iMac5,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.16 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache (per processor): 4 MB
Memory: 2 GB
Bus Speed: 667 MHz
Boot ROM Version: IM51.0090.B08
SMC Version: 1.9f4
Does anybody has any idea about this?
Tnx,
Denis
iMac 20'' (Late 2006) Mac OS X (10.4.10) 2 Gb Crucial DDR2 RAM @ 667 MHZ, WD My Book Premium Edition 250 GB

Others have also found what appears to be a discrepancy in the firmware that System Profiler reports installed on their Mac versus the version reported in Apple Knowledge Base documents. The definitive document for me is Mac OS X: Firmware Updates for Intel-based Macs. This doc confirms the information that you report, so the logical explanation to me is that, although the doc was last updated by Apple on 1 MAY 2007, there has been an update to installed firmware in Macs shipping since the doc was last updated.
But the firmware shouldn't have anything to do with whether your Mac sleeps or not. Sleep is one of the things regulated by the System Management Controller. This can be reset.
But there are many other things that can interrupt the Mac auto-sleeping; external FW/USB peripheral devices, wifi, Bluetooth, etc. Have you added any such devices recently.

NEW Firmware Version 6.01

All,
We are releasing version 6.01 firmware for the F5, and F55 motion picture cameras. Thank you for your feedback in discovering the S/Q, Center Scan issue.
When S&Q setting was set “On” in 2K Center Scan mode or 2K Full Scan mode and the power was turned Off and On, Recording did not work. This update fixes it.
This update includes all other features and functionality as posted in the previous version 6.0 announcement
http://www.community.sony.com/t5/F5-F55/NEW-Version-6-Firmware-F5-and-F55/m-p/506807#M28137
PMW-F55/F5 Firmware Version V6.01 Release note
June 30th, 2015
This document explains about firmware update of PMW-F55 V6.01 from PMW-F55/F5 V6.00. The latest firmware version of related products is below.
Product name
Latest firmware
Release date
PMW-F55
V6.01
This announcement
PMW-F5
V6.01
This announcement
AXS-R5
V4.1
Aug 8th, 2014
AXS-512S24
V1.2
June 5th, 2013
AXS-A512S24/A1TS24
V1.0
Mar 17th, 2014
AXS-A256S24
V2.0
Mar 26th, 2015
AXS Utility Software
V1.3
Feb 28th, 2014
RAW Viewer
V2.2
Feb, 28th, 2014
This firmware can be updated from V6.00, V5.11, V5.10, V5.0, V4.12, V4.11, V4.1, V4.0, V3.0, V2.11, V2.1 and V2.0. When you want to update F55 and F5 from V1.22 and earlier, you must update to V2.0 first. https://community.sony.com/t5/F5-F55/NEW-Firmware-release-Version-2-0/m-p/195623#M6582
Regarding the procedure and functions about V2.0, please refer to “PMW-F55/F5 Firmware Version V2.0 Release note” which was released on Oct 4th, 2013. And F55 and F5 must not be downgraded to previous versions after updating to V2.11. We couldn’t guarantee any troubles after downgrading. An “All File” generated by a previous firmware version can be loaded to V6.01 of F55 and F5.
NOTE:
The new Firmware V6.01 for PMW-F55/F5 is only compatible with AXS-R5 running with Firmware V4.1. If your AXS-R5 has installed an older version, please update to the current Firmware V4.1 the same time. https://community.sony.com/t5/F5-F55/NEW-F5-F55-Firmware-Version-v4-11-and-AXS-R5-v4-1/m-p/410782#M19813
<<Modification from V6.00 of F55 and F5>>
Bug Fix
When S&Q setting was set “On” in 2K Center Scan mode or 2K Full Scan mode and the power was turned Off and On, Recording did not work. This has been fixed.
Sometimes specific All Files could not be loaded. This has been fixed.
<Notification we would like to share>
iOS setting for Wi-Fi Remote
While using Wi-Fi Remote by iOS devices and Safari, please turn off Private browse function.
All file Support
All files which are created with Firmware V6.01 are not compatible with an earlier firmware version.
<< Version up procedure >>
Please refer to “Version Up Guide for PMW-F55 and F5” - documents are below for download
Firmware download:
F5
http://pro.sony.com/bbsccms/assets/files/show/highend/downloads/PMW-F5_V601_6.01_4_2015-06-24_14-42-14_firmware.zip
F55
http://pro.sony.com/bbsccms/assets/files/show/highend/downloads/PMW-F55_V601_6.01_5_2015-06-24_14-42-07_firmware.zip

Hi, AlexK. I just found the answer for your question in F5/F55 user manual(v.6), on p. 46.In a word, you can't use your double speed viewfinder function.Refer to the last sentence. Viewfinder Double Speed function is not effective on the following settings.- When System Frequency is 59.94/50.- When Recording format is SStP Sr-SQ 444 / SStP SR-SQ Lite 422 / SStP SR-SQ 422, ProRes 422, DNxHD 220x / DNxHD 145.- When "Setting" in "Slow Shutter" of the Camera menu is set to "On."- When "Setting" in "S&Q Motion" of the Camera menu is set to "On," and the "Frame Rate" setting is 1 to 60P. At this moment, it's not available to everyone.Hope Sony make it available with future firmware update, if technically possible. Bryan

100% CPU usage. RV180W Firmware Version 1.0.2.6

Since I updated to Firmware Version 1.0.2.6 cpu usage shows 100% with no sing of lowering.
So since 2 days now its always runngin at full speeds for no reason.
Firmware Update, Factory Reset, Setup as before. => 100% CPU
Is this a common problem? Is there any fix for that? Or at least a way to get informations what causes this?
Kind reagards
bartlingja

Hi, we can try something, please download the firmware thru this link, and install it again, then configure just the necessary configuration. If the issue continues, could you please reach out to our Small Business Support Center and open a Service Request to address this issue? One of our Engineers may be able to work with you and diagnose the root cause. You can find the appropriate contact information for SBSC in the below link.
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
I hope you find this answer useful
“Please rate useful posts so other users can benefit from it”
Greetings,
Johnnatan Rodriguez Miranda.
Cisco Network Support Engineer.

WRT120N working firmware version 1.04

Similar Messages

Maybe you are looking for