WRT150N v1.1 needs to be reset 2 - 3 times a day

Router stops working (both wired and wireless) but the front panel lights give no indication of a problem. I have to unplug power to my router to reset it a couple times a day. Any ideas?

try upgrading / reflashing the router's firmware ... after the upgrade , reset and reconfigure the router .. check whether it helps ..

Similar Messages

Iphone 4 hard reset atleast 2 times a day

Ever since i got my iphone 4 32g i have had to do a hard reset atleast 2 times a day. Out of the blue it shuts down and doesnt turn back on unless i hold the two buttons for about 30 seconds. I restored it to factory like they asked and still it does it. Also if im listening to music and the phone rings it wont let me swipe to answer. Anyone else experience this.

If it still does this after a restore as new with only the default apps on it, then I would return it and get it replaced under warranty. There is no other troubleshooting you can do.

Help! I need to restrict wired access by time of day to limit XBOX 360 use

AirPort Extreme N allows timed access restriction for wireless clients, but Apple bewilderingly decided not to make this feature available to "wired" clinents that access the network via ethernet cable. *This permits our teenagers to play XBOX all night long.* HELP! Which third-party vendor makes wired routers that I can use to restrict this access by time of day. NOTE: I will need a router that still supports AppleTalk over ethernet to keep my HP LaserJet working. I tried a LinkSys router but it killed the AppleTalk packets and wreaked havoc with print jobs sent to the HP. I also want to keep the AirPort Extreme N in the network and use it as the sole DHCP server (I specifically need its ability to reserve private IP addresses for some devices), so this complicates where in the network I place the third-party router. Where should this router be, if I need the AirPort Extreme N to serve as DHCP server, and do I need to change any other setting like bridge mode, etc? _I just can't believe Apple would only allow timed access restrictions for wireless clients._ Come on! Maybe this will be fixed in a firmware update?

Thanks, Duane. I was just looking at the PDF instructions for this router, and it offers extensive control of wired time access by IP number.
So: If I (1) put this Belkin device at the top of my network chain, between my cable modem and my AirPort Extreme; and I (2) turn off the DHCP server in the Belkin device but turn on the DHCP server in the AirPort router; and I (3) use the AirPort Extreme to assign a reserved IP adddress to the XBOX; and I (4) use this reserved IP address to restrict the XBOX access by time of day via the Belkin router software... Everthing will work OK?
Seems awfully complicated. Basically, I would be using the Belkin router only as high-octane network switch -- one that permits timed access resrictions for devices at specific IP addresses (and handshakes with the cable modem to provide a unique MAC address to the cable company). Right?

Ipod need to be reset all the time

Hi recently my Ipod is acting weird. if i don turn it on for 1 day the following day i need to reset it else nothing happens.
Is this supposed to be happening? I didn't hv this problem before.

Anita,
I know you said that you need to reset your iPod (and by that I take it to mean you have to do it yourself), but are you aware that the iPod resets itself after being left inactive for a period of 36 hours or so?
See iPod Sleep.

Wrt54g needs reset 2-3 times a day. (version 8)

okay, I am frustrated to no end. I have called tech support and they tell me it is my ISP. I call my ISP and they tell me it is my router...
I have my wrt54g hooked up to my 1.5/758k dsl. I can connect my dsl modem directly to one PC and it works beautifully. When I place the router in use and start using both my computers, I enter a world of frustration and anger.
Here are some more deatils:
My connection: Static IP, pppoe, 1.5(down), 768 (up)
my network: 2 computers, one wired, one wireless (laptop), ssid broadcast disabled, 128bit encryption.
problems: constantly lose connection, sometimes reset works, sometimes I have to do a hard reset (reset button) and re-configure router. I have tried disabling wireless and ran a cable to my laptop but the problem still exists. Tech support suggested one of my computers had a virus... I ran scans on both computers with AVG (no virus) also ran spybot, spysweeper, adaware, pestpatrol, avg-as + trendmicro (NOTHING FOUND!!!)
I tried to take this heap of worthless plastic back to bestbuy but I did not have the box or receipt and they could not look up my past purchase made on a gift card (!!!!!!)
someone please help before I take extreme measures and smash this router with a sledge hammer!!!!

Are you using any peer-to-peer (P2P) software? This is known to cause router slow downs and disconnections. Go into the P2P software and reduce the number of connections that the software can make.
You need to do a few tests on your system, to try to isolate your problem:
1) Turn off the laptop. If you have the laptop wired to your router, disconnect this wire. Wire only your wired computer to the router --- does this give you a properly working Internet connection, without disconnections?
2) Turn off your wired computer, and disconnect the ethernet wire that connects it to the router. Next, wire only the laptop to the router -- does this give you a properly working Internet connection, without disconnections?
3) Disconnect the ethernet wire from the laptop. Next connect your laptop wirelessly to the router. Does this give you a properly working Internet connection, without disconnections?
Are you using any fixed LAN IP addresses on your system? If so, list the addresses that you are using, and also state your DHCP server range.
Also, state your ISP and the make and model of your modem.
Also, has your router ever worked correctly, or is this a new setup?

Need to batch reset iPhoto pic time to EXIF time

Hi gang,
I have found a bunch of old pics in my iPhoto library that don't have the correct time assigned to them. For example, a pic taken at 5 PM is listed in iPhoto as having been taken at 8PM. If I "Reveal in Finder", then open the pic in Preview, the EXIF time is correct (5PM).
Is there a way to have iPhoto reset pic times back to the original EXIF time? I found some old scripts (Joe's iPhoto Applescripts), but they look quite out of date. I would be anxious running them on my current library.
I am using iPhoto 11 (v9.4.2).
Cheers!

I'm not sure how you have changed the date/time in iPhoto - but using smart albums you can identify photos form a specific camera - or many other attributes
in Events view the default sore is by date/time so I would expect the problem photos to be grouped together -- and in Photo view you can select several different sorts and by truning off show event titles you can view all of your photos as a single group
I'm not clear on whart you found or what you are expecting but the way to modify the contents of the iPhoto database is to only use iPhoto to do it - never make any changes of any sort directly to the files in the database
LN

Must reset modem multiple times a day.

This is a problem I noticed other people in my area are having. I must reset my D-LINK 2750B modem at least 10-15 day in order to regain connection to the internet. What is the issue? Should I return this modem for a replacement? I have tried other suggestions posted in this forum. It is an annoyance and not worth the amount paid for the service. Thank you.

I am sure you've heard this before. I too called several times on the same issue. The tec says I'm to far from post. The line quality sucks. I'm with you . Why are we paying for this if the dang thing doesn't work most of the time. Please there must be something to be done to fix the issue.....

Blackberry 9810 keeps resetting itself several times a day

The screen seemingly randomly turns off and take a couple of minutes to reset itself. Usually it happens after dialing or opening the slider. I have tried all of the resets including Safe Mode and the only thing that I can see to try is to Clean Install the Blackberry OS. I have started and Blackberry does not have a Fido for this model as Fido does not provide one. It was originally a Telus phone. How do I do a clean install and will I have any problems with Fido with a Telus OS on my Blackberry. The unit is unlocked and has successfully worked for about 6 months.Thanks, Allan

Hi and Welcome to the Community!
Lousel3300 wrote:
will I have any problems with Fido with a Telus OS on my Blackberry.
There is no requirement to use any specific carriers OS package. The only requirement is to use an OS package that is for your specific model BB, but if the OS comes from a carrier other than that for which your BB was originally manufactured, there is a necessary "trick".
Lousel3300 wrote:
How do I do a clean install
At the top of each device forum, there should be some "sticky" threads that discuss the OS levels available for many models. If they include your model, then please use those as reference as you proceed. Otherwise, you will have to dig through the official download portal for OS packages for your model:
http://us.blackberry.com/support/downloads/download_sites.jsp
From a PC, you can install any compatible (e.g., for your exact BB Model Number) OS package to a BB via this procedure:
http://supportforums.blackberry.com/t5/BlackBerry-Device-Software/How-To-Reload-Your-Operating-Syste...
Note that while written for "reload" and the Storm, it can be used to upgrade, downgrade, or reload any BB device model -- it all depends on the OS package you download and install to your PC. If that OS package is from a carrier other than the carrier for which your BB was originally manufactured, then delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
Be sure that you remove, from your PC, any other BB device OS packages as having more than one installed to the PC can cause conflicts with this procedure.
You may also want to investigate the use of BBSAK (bbsak.org) to perform the wipe it is capable of.
You may also want to try this procedure to perhaps narrow down the precise causal item:
Load your OS "bare bones"...if anything is optional, do not install it.
If the behavior presents immediately, then try a different OS with step 1
If the behavior does not immediately present, then run for as long as it takes for you to be sure that the behavior will not present.
Add one thing -- no matter how tempting, just one.
If the behavior does not present immediately, then again run for long enough to be sure it will not have the same problem
Repeat steps 4 and 5 until all things are loaded or the behavior presents
When the behavior presents, you know the culprit...the last thing you loaded.
If the behavior does not re-present, then you know that either step 1 or 2 cured it.
If the behavior presents no matter what, then you likely have a hardware level issue for which no amount of OS or software can cure.
If you are on MAC, you are limited to only your carriers sanctioned OS packages...but can still use any levels that they currently sanction. See this procedure:
KB19915How to perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

D-LINK/ Power reset multiple times a day

I have seen multiple threads with this issue. I called in roughly 6 months ago, and found out that I was on the 3.5-7 MBPS and it was way too fast for our area, everything kept timing out so we moved down to 1.1-3 MBPS. Well, that still hasn't stopped any of the loss of connectivity issues. I still have to reset it multiple times a day. Once it's up and running our speeds are some what efficient. I just called today (1/4/14), and the service tech was saying that it might be the modem, but since it's not acting up she can't tell what the problem might be (Big Help!). Then I asked since she thinks it could be the gateway/router if we could get a new one and see if that might be the problem. Pretty much just asking if we can start somewhere so we can eliminate some of the possible problems. She told me that I would have to buy a new one for $39.99.
Is there anybody who might be able to help me with this, or has had to deal with this in the past? What were your solutions to fix the issue?
New Home
Cat6 Cable (Home Run)

Your issue has been escalated to a Verizon agent. Please go to your profile page for the forum, and look in the middle, right at the top where you will find an area titled "My Support Cases". You can reach your profile page by clicking on your name beside your post, or at the top left of this page underneath the title of the board. you will find a link to the private board where you and the agent may exchange information.
To ensure you know when they have responded to you, at the top of your support case there is a drop down menu for support case options. Open that and choose "subscribe".This should be checked on a frequent basis as the agent may be waiting for information from you before they can proceed with any actions. Please keep all correspondence regarding your issue in the private support portal.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer that solved your issue as the accepted solution.

WRT150N needs to be reset every week

WRT150N V1.1 Firmware 1.01.9
On average once per week all of the devices in the house can no longer connect to the WRT150N. Unplugging the WRT150N for 30 seconds and replugging it in invariably solves the problem.
My WRT54 did this too, but I figured it would've been fixed by now.
Is there a solution to this problem?
Everytime I have to reset the WRT150N, I have to reset my NAS - everything seems to recover ok - but it is still a pain.
Thanks,
Bob

I already have the latest firmware. Like the people on the thread below that goes on for 7 pages about the same problem, I have tried a lot of these standard solutions and none work for any great length of time.
It also turns out it isn't once a week - my wife said she actually has to reset the modem almost every day when she goes to use the internet!
I will probably just dump this thing. It sounds like the Airport Extreme is a popular choice.
If there is a real solution I would like to hear it before I spend more dough.
Thanks,
Bob

I need help with resetting my ichat. When i try to login now it wont let me... it says "AOL Instant Messenger password" and then "iChat can't log in to ... because your login ID or password is incorrect. How do I reset this if I cant log in?

I need help with resetting my ichat. When i try to login now it wont let me... it says "AOL Instant Messenger password" and then "iChat can't log in to ... because your login ID or password is incorrect. How do I reset this if I cant log in? When I try to press online the same thing pops up and I have no way of logging in or asking for help.

Hi,
iChat (it would help to know which version) can accept Apple IDs as valid AIM Screen Names.
However if you have iChat 5 or earlier you cannot use ones ending in @me.com or @icloud.com issued by iCloud. (they can be used in iChat 6 or Messages as these versions make a double login to AIM and Apple to allow the use of the password).
In addition if you are using an Apple ID for an AIM Screen Name the password still needs to keep to the 16 character limit that AIM has.
AN @mac.com name can be used on any version of iChat (Until the 30th June 2014)
As it does not need a double check with Apple you can use it to log in to the AIM Web pages
Login here with an AIM Name registered at AIM or and @mac.com name and see if you get any suspended account messages.
Sometimes account can be suspended. Usually because something has triggered the "Unusual Activity" item.
About a year ago many @mac.com users that travelled out of their own country found themselves suspended when they got home.
If the Name checks out of if an Apple ID the password in known to be 16 characters or Less then do this:-
In Lion upwards open a Finder Window and use the Go Menu whilst holding down the ALT key.
Select the Library that appears in the menu list.
Navigate to Preferences.
(If you have version earlier than Lion the just navigate to ~/Library/Preferences (that's the Library in you Home - Little House icon - folder)
Fnd com.apple.ichat.aim.plist (even if you are using Messages)
Drag the file to the Trash and Restart the app.
7:39 pm Thursday; May 29, 2014
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

Macbook 13" 2009 shutting down when moved randomly and when finally able to turn back on time and date needs to be reset.. Help?

2 times in the last week when i have picked up my macbook to place beside me it has shut down, and takes a little while to turn back on, when it does turn on again the date and time needs to be reset and wifi password needs to be re-entered as well..
I have no idea what is going on but i dont like it... any help would be great !!

That battery is relatively healthy, say relatively due to the high cycle count, the number of full charge cycles it has had. The lower capacity simply reflects the high number of charge cycles and is not an issue, only a measure of how long the MacBook will work when running on battery power. The voltage is right where it should be for a MacBook, in the range of 11.5 to 12.5 volts...12.3 volts is a strong battery.
Now to the auto-shutdown for lack of a better term - that sounds a lot like something loose inside the MacBook that when jarred shorts/shutsdown the sytem with a loss of basic information. You could try things like an SMC reseet or PRAM reset but I seriously doubt they would have any affect. Best option would be a visit to an Apple store genius bar to have the techs run some diagnostics to see if they can identify something going wrong inside.
Hope this helps and you can find resolution...auto shutdowns of this type are not really good for the system.

30GB IPOD needed to be reset to factory settings...HELP

my 2 yr old 30 GB ipod needed to be reset to factory settings as it was not being recognized by my computer or itunes. It stated the the ipod was corrupt. Apple support in Burlington suggested to reset to factory settings as othe measures didn't work. I now have new computer and need to know if I have to reload the itunes CD or just login to Itunes store.

You need to download the latest version of iTunes from Apple (the "itunes store" is not involved).
http://www.apple.com/itunes/
The disc that came with the iPod will have an older version of the software, so download the latest. Install iTunes. Put all of your music and other media into the iTunes library. Connect the iPod. It should be recognized by iTunes. Depending on the current settings on the iPod, it may or may not ask if you want to sync the iPod to the iTunes library. If you sync, the music in your iTunes library will be copied to the iPod, and replace whatever music is already on the iPod.
If you want to Restore the iPod to erase it and and initialize the software, select the iPod in the iTunes sidebar and click on the Restore button. This will install the latest available software for the iPod (technically not "factory settings"). After the Restore process completes and the iPod restarts, iTunes will again ask if you want to sync the iPod to your library or not (do it manually).

I need to hard reset my ipod touch 5th generation how do I do so?

My ipod is hooked up to my windows computer but will not connect to itunes and is showing disabled with find my I phone. It has been password protected by my child and I need to factory reset it. However I have out lived my warranty and am trying to fix without having to go through Apple.

Forgotten Passcode or device disabled after entering wrong passcode
Be sure to read the If you have never synced your device with iTunes, or you do not have access to a computer section

Ipod video needs to be reset when using shuffle songs.

I like to shuffle my 4800 plus songs on my new ipod, but I have noticed that after turning it off for an extended period of time usually a couple hours or over night, it needs to be reset. I have not tried to retore it as of yet, but I plan on to see if that helps. Has anyone else experienced this?
Ipod video 5.5 Windows XP

restore did not work, guess I'll just have to live with it until apple does a firmware upgrade.

WRT150N v1.1 needs to be reset 2 - 3 times a day

Similar Messages

Maybe you are looking for