WRT160N - does it support multiple vLan configurations?

I'm trying to find more detailed tech. specifications of this thing (WRT160N), but unfortunatelly I get only some basic marketing messages... I need to understand if this router supports vLAN configuration, as I'm thinking to have IPtv and internet on the same. My provider does integrates the IPtv into separate vLAN, but their HW is not too good in other perspectives... So I'm thinking about linksys.
 So does it support multiple vLAN configuration (i.e. dedication of separate vLAN to exact port)?

No. VLANs are not supported in Linksys devices. You'll have to look at Cisco Small Business or better.

Similar Messages

  • HT201250 Hello i am using TimeMachine to back-up entire Mac image (data + system) on an usb-local drive. I would like (on top of it) add a specific plan to back up some files on a remote network drive. Does TimeMachine support multiple back-up plans ? How

    Hello i am using TimeMachine to back-up entire Mac image (data + system) on an usb-local drive. I would like (on top of it) add a specific plan to back up some files on a remote network drive. Does TimeMachine support multiple back-up plans ? How ?

    Time Machine is capable of backing up to multiple locations, and can be used to back up to both a local hard drive and a networked drive (provided that that drive is in or connected to a Time Capsule or another Mac that is sharing it over the network). The catch, though, is that you can't specify different things to back up to different destinations. Whatever you exclude from Time Machine backups is excluded from ALL backups, and whatever is included is included on all.
    So, get a large enough drive that you can back up everything you want in all locations, or use something else for maintaining the network backup.
    More information on these topics can be found here:
    How do I set up Time Machine to a shared drive on another Mac?
    How do I set up Time Machine to a Time Capsule or Airport Extreme?
    "Rotating" Time Machine backup disks

  • Does JTree support multiple DnD?

    I'm working on an applet which displays a JTree tree, which has to support multiple DnD.
    i mean, user has to be capable of selecting several nodes at a time and drag all of them, dropping them into a target.
    Though i have asked about it, and somebody told me about it, the solution was with a JFrame, and all the examples which work and i've read, arre with JFrame.
    So i guess that maybe JTree does not support multiple DnD, and moreover, there is a website
    http://bugs.sun.com/bugdatabase/view_bug.do?bug_id=4165577
    in which someone says that, in fact, JTree does not support it. But it's and old page, so i want to know if at present, Jtree still has this debug.
    Thanks in advance!

    http://www.java-forum.org/de/viewtopic.php?p=139820#139820

  • Why java does not support multiple inheritance ???

    Hai friends ..iam new to java .. i have doubt ..plz help me
    Why java does not support multiple inheritance ???

    The reasons for omitting multiple inheritance from the Java language mostly stem from the "simple, object oriented, and familiar" goal.
    To understand multiple inheritance, the learner needs some level of expertise like virtual derivations etc in c++. Multiple inheritance will allow method duplication, and throws the learner into confusion which method might be called by the compiler in which scenario at run time.
    Even though this answer seems to be funny, this is the actual reason why java omitted multiple inheritance of classes.
    But java support multiple inheritance of interfaces. Multiple interface inheritance allows an object to inherit many different method signatures with the caveat that the inheriting object must implement those inherited methods.

  • Does endeca support multiple keyword search

    Am new to endeca.
    Does endeca support multiple keyword search in atg crs.
    an eg can we search for "shirt,shoes" and get results for both

    How specifically to implement this depends on how you are querying Endeca.  With a simple URL parameter query using the UrlENEQuery object you would set the parameter of Ntx=mode+matchany, and if you were using the ENEQuery class you would set it like:
    ENEQuery query = new ENEQuery();
    ERecSearchList searchList = new ERecSearchList();
    String matchMode = searchTerms.contains(",") ? "mode+matchany" : "mode+matchallpartial";
    ERecSearch search = new ERecSearch( "your-search-interface", searchTerms, matchMode );
    searchList.add( search );
    query.setNavERecSearches( searchList );
    If you are using the Assembler Service, you can include the Ntx parameter in the call, so you would wrap your call with some conditional logic, e.g.:
    String serviceCall = null;
    if( searchTerms.contains(",") ) {
       serviceCall = "assember/xml/browse?Ntt=shirt,shoes&Ntx=mode+matchany";
    } else {
      serviceCall = "assember/xml/browse?Ntt=shirt,shoes&Ntx=mode+matchallpartial";
    If you are using the Content Assembler API within your application, it will depend on how you are invoking it but some of the above should help you customise appropriately.
    HTH
    Michael

  • I am looking to turn my iPad into a portable device to store and view multiple files transferred from my pc. I have tried some apps but it does not support multiple sub folder transfers.  Any suggestions please?

    I am looking to turn my iPad into a portable device to store and view multiple files transferred from my pc. I have tried some apps but it does not support multiple sub folder transfers.  Any suggestions please?

    I use GoodReader on my iPad and use the GoodReaderUSB tool. the GoodReaderUSB tool allows you to transfer entire folders into GoodReader without loosing the folder/file structure.
    Windows: http://www.goodiware.com/usb/GoodReaderUSBWin_200.zip
    Mac: http://www.goodiware.com/usb/GoodReaderUSBMac_202.zip

  • Multiple vlans configuration issue with RV016 router and SG 300-10MP witch

    Hi,
    I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
    Router (RV016 10/100 16-Port VPN Router) as gateway mode:
    IP : 172.16.0.1/24
    DHCP Server :
    IP : 172.16.0.2/24 GW: 172.16.0.1
    2 subnets :
    172.16.1.0/24 GW: 172.16.1.1 to serve vlan 1
    172.16.2.0/24 GW:172.16.2.1 to serve vlan 2
    Switch (SG 300-10MP 10-Port Gigabit PoE Managed Switch) as layer 3 mode:
    IP 172.16.0.254 (vlan 8 default)
    Vlan 1 : 172.16.1.1
    Vlan 2 : 172.16.2.1
    1 device connected on each vlan
    a workstation on the vlan 1
    a laptop on the vlan 2
    In this scenario (see the attached pdf file) the DHCP server is connected on a router, hosts on vlans dont receive any IP address.
    But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.
    I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration ?
    I hope the explanations are clear enough and my English too
    Any help will be highly appreciated,
    Zoubeir

    Hi Eric, the small business group doesn't support the ASA config, but  I can help with the switch.
    A couple things I notice in your description-
    48 port (192.168.1.254) and the other 24P (192.168.1.253)  we have a  second vlan 20 set up on the 24P switch (192.168.2.253)  we have ports  1-12 set for vlan20 (untagged and trunk), the remaining ports on on the  default vlan 1.
    The connection between the switches, is it 1u, 2t?
    The link between the switches should be 1u, 2t, the switches support the trunking and vlan tagging, meaning all communication will work fine.
    We have the 24p and 48p switches connect using GE1 and GE1.  We are unable to ping a device on vlan 20 ( on the 24p switch
    The 24p switch should be in layer 2 mode, if you have the 48 port l3 switch upstream. Additionally, you need to have the default gateway set on the 24p switch.
    We have a static route set on the 24p switch (0.0.0.0 192.168.1.0). 
    Between the switches, it shouldn't require any static routes, assuming you correctly trunk / tag your ge1 ports, with both switches operating in l3, the ip route table dynamically builds the connected routes, therefore a static route is redundant.
    -Tom
    Please rate helpful posts

  • Multiple SSID With Multiple VLANs configuration on Cisco Aironet APs: Assotiated clients cannot obtain IP addresses

    Hi Surendra,
    I was just given this task to see how i can configure a second ssid for guest access in our environment.
    this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
    Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
    Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time.
    My AP config is attached below.
    Please tell me what am I doing wrong.
    Do i need to redesign the whole network to have a native vlan other nthan the data vlan?
    Does the access point need to be aware of the voice vlan?
    Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
    I will greatly appreciate your urgent response.
    Thanks in advanced.

    Hi,
    As far as i know we dont set the ip helper address on the radio interface. It should be on the L3 interface of corresposding VLANs i.e.
    int vlan 20
    ip helper-address 192.168.33.xxx
    int vlan 60
    ip helper-address 130.20.1.xxx
    I'm assuming that your using SVI's (int Vlan 20 and int Vlan 60) rahter than physical interfaces. Also hope you have configured switch port as trunk where this AP is connected.
    Modify the AP config as below since you are using data vlan as the native vlan
    interface Dot11Radio0.20
    encapsulation dot1Q 20 native
    interface FastEthernet0.20
    encapsulation dot1Q 20 native
    Ideally your AP fastethernet configuration should looks like below and not sure how you missed this as this comes by default when you have multiple vlans for multiple ssids.
    interface FastEthernet0.20
    encapsulation dot1Q 20 native
    no ip route-cache
    bridge-group 20
    no bridge-group 20 source-learning
    bridge-group 20 spanning-disabled
    interface FastEthernet0.60
    encapsulation dot1Q 60
    no ip route-cache
    bridge-group 60
    no bridge-group 60 source-learning
    bridge-group 60 spanning-disabled
    Hope this helps.
    Regards
    Najaf

  • Does Siri support multiple languages

    I live and work in a multilingual environment. As a result, I often have to send SMS and emails in English, French, Italian or Portuguese. With the keyboard, I am used to switch language with the globe key next to the spacebar. With Siri however I am not sure how this can work. When it does eventually support the above languages, will I be able to use different languages without changing the whole telephone setting? Can one say "send email to my wife: buongiorno amore"? It would be a real letdown if the coolest feature of iOS 5 were unusable to me...
    Thanks

    Yes, exactly. I am using Siri in English since she gets better along with the rather easy synthax (compared to German). Unfortunately you cannot switch directly when writing a message. For example, if you tell her to "write a message to my wife", you may immediately dictate what you want to say but only in English. If I want to write her in German instead, I will have to tap once on the message area. She then instantly changes to German (or any other language that was used as keyboard before) which also affects Siri's voice recognition. But one tap is reasonable.

  • PM : Does PM support multiple  Class types for Equipment classification

    Hi,
        Do  Plant maintenance support multiple class types for the classification for the equipments.
    Our  Customer has created his own class type other than 002(Equipment) for the classification and wants to know weather PM supports such class types or not.
    Thanks and Regards,
    Anuj
    Edited by: Anuj Goyal on Mar 13, 2008 10:16 AM

    hi
    i think you can use the your own class type provided you have done all the settings related to the standard class type 002,also if you have create your class type your standard class type will be changed to either the newly created one or 002 based on settings made by you
    regards
    thyagarajan

  • Does Safari support Automatic Proxy Configuration with a .wpad file?

    Hello,
    I was wondering if anyone knows whether Safari supports Automatic Proxy Configuration with a .wpad file?
    Morgan

    HI Morgan ..
    Safari is extremely finicky about proxies and according to Wikipedia it dates back to older browser versions.
    http://en.wikipedia.org/wiki/Web_Proxy_Autodiscovery_Protocol

  • Designer 6.0 does not support multiple homes

    I installed oracle 8i database version 8.1.6 on my windows NT 4.0 laptop. I need to also install designer 20000 version 6.0 on the same laptop but I get the following errors.
    The location e:\oracle \oracle8i is already used as an oracle home for oracle 816 production. It can not be uses as an oracle home for NT.
    I then designate a new directory and home name, and get the following errror.
    Designer release 6.0 does not support multple home installations and suggest me to change it back to my first choice.
    How do I get both the oracle database and designer installed on the same machine without Oracle home problem?
    null

    Hi,
    Install designer 6 first in DeFAULT_HOME, directory ORANT. After you've done that, install Oracle 816.
    See reply to Davephobbs
    HTH
    Martin

  • How Java does not support multiple inheritance

    Hi,
    I have got a small doubt....
    Generally it is said thatjava does not support multipleinheritance.I agree.
    But then we know that every class in java by default is a sub class of Object class then how is it possible to inherit one more class using extends keyword.
    I am confused?
    Akshatha

    Generally it is said thatjava does not support
    multipleinheritance.I agree.Generaly, this is wrong. Java does support MI, just not MI of implementation. You can extend as many interfaces as you like.
    But then we know that every class in java by default
    is a sub class of Object class then how is it
    possible to inherit one more class using extends
    keyword.It is not possible. You can only extend directly from one single class. If you extend from something else than Object, you're not directly extending Object anymore.

  • Let's Be Honest / Save Time: Lenovo T430s (NVIDIA) DOES NOT Support Multiple Monitors

    There have been a few comments / complaints / articles around the web regarding the T430s and difficulties using multiple monitors.
    But since this capabilitiy is clearly documented in all of Lenovo's specifications and marketing literature, I went ahead and bought an i7, NVIDIA, SSD, T430s with the docking station and all the bells and whistles to facilitate 3 or even 4 monitors.
    Well please listen and let's be clear:  IT DOES NOT WORK. Therefore, to be clear:
    DO NOT BUY THIS MACHINE AND DOCK IF YOU WANT IT TO LIVE UP TO ITS MULTI MONITOR PROMISE.
    In the two weeks since FedEx arrived, here is the deal:
    1) I fussed around with the dock and monitors at home and the office to no avail, for most of TWO weekends.  (I am not a beginner).
    2) Then, I spoke to Lenovo in Atlanta's tech support for THREE HOURS.  No results
    3) I spoke to Lenovo's "premium support" (paid) for FOUR HOURS.  No results.
    4) I consulted with a 3rd party expert on mulitple monitors who was kind enough to remote into my machine for another HOUR.  No results.
    5) Muliple parties have confirmed that yes, all hardware is working and yes, everything can be seen in device manager, and yes, the NVIDA card is properly switched on in the BIOS, yes I bought the i7 version etc.
    6) And just in case, yes, we wiped the drive clean for a factory reset, yes we unistalled and reinstalled all the drivers and yes, we even deleted the Lenovo driver just in case the NVIDIA driver was newer or better and yes, we double checked the settings in the BIOS again.
    7) Yes, we tried every connector in the dock AND the laptop:  VGA, DVI, DP and mini DP - in EVERY possible combination.
    And NO, IT STILL DOESN'T WORK. AT ALL.  Two screens, take your pick, but THAT'S IT.
    Finally, not one but TWO technicians asked me to not quote them (so I wont mention any names) but that in their opinion IT JUST DOESNT WORK AT ALL, EVER, despite Lenovo's claims / insistance that it is configured for 3 and even 4 monitors.
    So the final conclusion was only that Lenovo must have rushed this T430 spec / configuration / capability to market (including the glossy brochures!) before figuring out that something is missing in the handshake between the mother board and the NVIDIA card? 
    Or in the firmware re swithing between the Intel (internal) and NVIDA card? 
    Or something else which prevents the NVIDIA card from seeing the ports on the laptop or the dock?
    In summary 1) you get NOTHING from the NVIDIA upgrade and with respect to more than 2 monitors, IT JUST DOES NOT WORK, AT ALL, EVER, PERIOD and END OF STORY.
    I too am a die hard old school Thinkpad enthusiast and with the company's service could match their classic products.
    I have an X201 that I generall love, but would appreciate more speed, an SSD and I have to drive at least 3 external monitors, using at least 1920 x 1080 resolution.
    Perhaps a W series Thinkpad would work, but I also travel so going up to the T430s was already a sacrifice vs the small size of the X201.
    There are some 3rd party solutions but they are expensive and not so sure how plug and play they are with 3 or more monitors - what the T430s and Mini Dock 3.0 are SUPPOSED TO DO.  But they dont.
    Not giving up yet, but this has been a real bummer.
    PS
    Lenovo was very focused, efficient, and uncompromising when charging my CC for "premium" support.
    Solved!
    Go to Solution.

    Thors,
    Thank you and happy to report, albeit after all the hours and now weekend number 3:
    1) For the moment, I am able to repeat the 3 screen performance using mini DP from the Thinkpad and 2 DPs from the dock to the external monitors
    AND
    2) For the first time ever, I am just now for the first time running the 3rd external monitor from the VGA port on the dock.
    That is what I meant by using the various ports on the dock, so that the Thinkpad can simply be docked and undocked without connecting the mini DP - the purpose of a dock obviously.  As stated in other threads and articles, various configurations of the dock ports supposedly work to achieve 3 external screens, but until today was not able to do this.
    That is the good news and thank you for all help.
    The bad news is I stil have no clear idea why this has been so difficult, or where the problem lives that consumed so many hours of my own time and many hours with Lenovo tech support as stated above.
    Some success seems to have happened only after more than one set of LONG updates to Windows 7 (?)
    If I can replicate this set up the office (where I have 3 of the same monitors) I will be almost there.
    Thank you again to all for help and support.

  • OCS 10g - Does it support multiple domain hosting

    Hi,
    We have installed OCS 10g for a domain university.edu
    Now, It provides only two available domains as local domains. ie, university.edu and .edu
    I would like to add some more sub domains (at least one more) such as college.university.edu to be a local domain in OCS for which it should accept emails.
    It this simple feature of multiple domain hosting supported in OCS.
    Kindly let us know some tips for it.
    Many thanks in advance.
    maas.

    I configured the domain about 2 years ago, so I have to go and look in my archive (which is at the office, I will not be there before the end of next week).
    The setup has 2 top level domains (one is .nl and one is .com). Under .nl about 4 domains are running, under .com only 1. If I remember corretly issues did raise with files. Calendar and mail are running as expected. This is on a 9.0.4 release though (not a OCS 10 R1 or R2). I did read loads of articles and had to patch even more. Luckily I printed all articles I read, so I can lookup the exect document numbers. If you can wait until next week, I can help you out.

Maybe you are looking for