WRT160N lost connection

Oftenly my WRT160N is losing connection to all wired and wireless computers in my house (3 wired, 2 wireless). Means I cannot connect to internet and also to 192.168.1.1 from none of my computers.
Last days it started losing connection 4 or 5 times a day (in former times only 3, 4 times a week). My solution is being to power off and power on again the router. It starts the LAN again. However I don´t want to be continously doing power off/on. What can be happening?
I´m using 2 wired switchs non-linksys, but last time it happened (some minutes ago) only my PC was working and was linked directly to the router (wire).
Can you give me a solution to my problem?
Regards
Solved!
Go to Solution.

Before you reset and re-configure your router you should download and upgrade the firmware...Click here and download the firmware...
Follow these steps to upgrade the firmware on the router : - Open
an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password type admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin(firmware file) and click on "Upgrade"-Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Then, Press and hold the reset button for 30 seconds.
Then, unplug the power keep holding down the reset button for
another 30 Seconds.
Plug back the power back in, and keep holding down the reset button
for 30 Seconds.
Release the reset button.
Click here and follow the link to re-configure your router...

Similar Messages

WRT160N Not Connecting Properly

I'm helping troubleshoot an issue with a friend's WRT160N router. Recently, she has lost connection to the internet from all wireless and hard-wired devices running through the router. Pings to the router from all devices are successful. Plugging the cable modem directly into the devices works fine. Power cycle of router did not fix the issue.
I have reset the router and tried running the installation CD again. It walks me through plugging the cables into the router, but while searching for the router after plugging the power cable in, the program times out saying "device could not be found". However, I can pull up a command prompt and ping the router successfully.
The primary issue appears to be that the internet is not streaming through the router. Any suggestions? Firmware has been updated as of 5/31/08.
Thanks in advance.

Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When
it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....

Adobe cloud has lost connection with the server

Adobe cloud has lost connection with the server, can't get adobe cloud to work so I can re-install photoshop to fix a corrupted DLL file.

*Adding new items/removing orphans*
Try iTunes Folder Watch or iTunes Library Updater. Folder Watch is much faster on the adding files front, can be set to run in the background and includes a useful exclusion feature, however it’s slow at removing orphans. iTLU is better for this although doing it manually after looking at a list of proposed removals generated by Folder Watch is probably faster still. iTLU can also be set to update iTunes when you've used 3rd party tools to change tag info.
You may need to amend the list of file types these programs look for. My list includes:
.mp3 .mp4 .m4a .m4b .m4p .m4v .mov .wav .aif .mid .ipa .ipg .ite .itlp .m4r .pdf
Note the last 6 types may not be recognised as already being in the library so should either be omitted from the search or you can add (at least for Folder Watch) individual exclusions for files you know are already in your library.
tt2

"Lost Connection with AIM" repeatedly

Hi there,
I'm using a new Linksys WRT54GL router with the DD-WRT v23 firmware -- which is otherwise fabulous, by the way -- but since going with the router iChat has been pretty unreliable. I can't connect to my sister in England (I'm in Canada): we keep getting "insufficient bandwidth" errors (I'm on a very hi-speed cable internet connection, so I don't think it's me!). Moreover, AIM frequently kicks me off iChat with the message "Lost connection with AIM".
I've configured my router using instructions linked from this forum. I'm forwarding the following ports to my computer:
5060
5190
5220
5222
5678
16384
And while I can connect to other users okay (except my sister, it seems), staying connected it a real issue. Can anyone recommend a fix?
Thanks,
Aaron.
PowerBook G4 15-inch 1.67 GHz Mac OS X (10.4.5) The last PowerBook ever!

Hi Aaron,
This last port should be a group of 20 ports (16384-16403)
iChat needs 4 ports from this group to do 1-1 Audio or Video chats.
Many Linksys have UPnP. It is found in the Administration tab. If you have this you could use this. Disable the Port Forwarding if you do.
Also port Forwwarding points to one IP/computer. If this is the case for you and you still have the device doing DHCP there is a cance you computer's IP has changed if it goes to sleep or is shut down when the lease time runs out.
Check this on your computer and the Port Forwarding settings.
10:26 PM Monday; February 27, 2006

"Lost connection with AIM" error message

Hi all,
I've been a long-time iChat user — I've had very few problems, but now, at home, whenever I've been connected for about 10-15mins, iChat just disconnects with the simple iChat Connect Alert that the app has "Lost connection with AIM. The connection with the host was unexpectedly lost."
My Buddy List collapses to a "disconnected" header and I diappear from my Buddies' buddy lists. If I'm in the middle of a chat (video, audio or text), the chat continues uninterrupted, but I still disappear from people's lists as if I'd disconnected manually. Weird.
The net result is that I have to keep checking to see if I'm connected and then reconnecting all the time. A real pain in the proverbial.
It only happens at the house. My laptop doesn't disconnect if I'm at the office, for instance.
I have cable, coming in to Netgear 814v2 router; out to an 8-port gigabit switch, which then feeds my three main machines. All via ethernet cabling.
All machines have the same problem described above.
I've made the usual Quicktime setting changes.
I've listed the necessary ports in my Mac firewall settings (even though the firewall is turned off).
Each machine has a dedicated IP issued by the router (10.0.0.2 thru 10.0.0.5)
The router firmware is up to date.
What else is there?! I have no problems initiating or joining any sort of chat with my buddies around the world. I have excellent bandwidth. My internet and email are never interrupted 24/7.
Can someone help me? Pretty please?
17" Powerbook G4 & Dual G5 2.5Ghz Mac OS X (10.4.7)

Hi
Try this log on to AIM on port 443 rather than port 5190
Go to IChat > Preferences > Accounts.
Log out of AIM and then use the Server Settings tab
Set the port to 443.
Log back in again.
Tony

I can no longer log into my ichat linked to my gmail. right after opening up ichat, receive the following message: lost connection with jabber. the server has unexpectedly disconnected.

i can no longer log into my ichat linked to my gmail. right after opening up ichat, receive the following message: lost connection with jabber. the server has unexpectedly disconnected. how to troubleshoot? thanks.

Hi,
There can be many reasons why the Login is "up the creek".
Any break in the network at your end whilst logged in will cause an issue.
A sort of discrepancy between what iChat thinks the state should be and what the server thinks.
If they don't agree the server will refuse to accept.
A Crash at the server end which does not log you out properly will also do it.
Any file at any time can be come corrupted.
Luckily with the iChat .plists they are recreated if removed with an iChat Restart.
If it were AIM you can also get your Account Suspended and this will not log you in.
(It tends to happen from Chat rooms where people notify AIM about bad behaviour (as they see it) and you have to apply to get Un-suspended).
Most of the big IM services use multiple servers.
Sometimes these go out of Sync.
In the case of AIM this happens when they remove Old unused Screen Names from people's Buddy List prior to making them available for re-registration. I am not sure if this happens at Google.
You seem to be talking about an account that has worked at Work and having new computer at home.
As I mentioned the Priority thing you have not said that it has coincided with the new computer logging in (this will kick the work Computer out of Google whether you are logged in on the Web Mail page or in iChat)
IN addition to that iChat stays partially logged in for Off Line IMs
This is done in the background by a support app called iChatAgent
If your Computer is ON but ichat is not started people can still send you Messages.
Instead of saving these on the server until you login iChat will start up.
Depending if the home Mac is effecting the Work Login it may be holding sway over your Login.
Using your girlfriend's login may have booted her Off Line where she normally uses the name/login.
The AIM Side can be specifically set to allow Multiple Logins and therefore NOT allow them. If this happens you get a warning and messages to do something about it.
You do not get these in any Jabber or Google Login as the Priority setting is supposed to take care of it.
If the Login works at the Web Mail Login and on one computer then the .plist on the work computer is the most likely issue.
There is a small chance that a Corrupt Buddy Pic (Home Folder/Library/Caches/com.apple.iChat/Pictures) may be the cause.
Set this folder to icon view and also use the Finder's View Menu > Show View Options and select icon view.
This should show all pics as their icon.
Check that all display properly.
At this point I would try a COMBO version update install of the last Update you did over what you have.
This often corrects hard to trace things
The 10.5.8 COMBO is here
11:28 PM Monday; June 20, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
 Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Lost connection with server

For about two days now, the bbm application has refused to launch. It has been writing lost connection with server....can any one please help! It's really urgent

Hi and Welcome to the Community!
With a strong carrier network signal (e.g., not merely WiFi), I suggest the following steps, in order, even if they seem redundant to what you have already tried (step should result in a message coming to your BB...please wait for that before proceeding to the next step):
1) Register HRT
KB00510 How to register a BlackBerry smartphone with the wireless network
Please wait for one "registration" message to arrive
2) Reboot
Pre-BB10 Devices ONLY. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes.
BB10 Devices. Hold the top button down until the counter reaches zero. Wait for the device to be fully shut down (e.g., nothing at all displayed on the screen, no LED lights, etc.). Hold the top button until the red LED is lit. Wait through the full boot-up process. IF this fails, you can attempt the battery-pull method above, but it is normally NOT recommended unless nothing else works.
See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Hopefully that will get things going again for you! If not, then you should contact your mobile service provider for formal support.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

My iMac running mountain lio SO 10.4 has lost connection with my Kodak ESP5200 printer. Both are connected to my ISP router OK

My Imac conputer has lost connection with my printer.
The Computer is running Mountain Lion OSX10.4
The printer is a ESP5200
Both are commected to the router.
Any ideas ??

Follow the steps @ > Troubleshooting printer issues in OS X

NVIDIA OpenGL driver lost connection with the display driver

Alienware M14x Laptop
Windows 7-pre 64-bit
8gb ram
3gb Video: NVIDIA GeForce GT 555M
Intel i7 2760QM
AE CS4
AE keeps crashing. I get the following message while doing something as simple as scrubbing through the timeline, or changing opacity of a layer. in 1080p, I have a picture layer, a solid, some color corrections, and that's it. i just got this new computer and i have never had this problem on my old computer.
this message appears after AE crashes."The NVIDIA OpenGL driver lost connection with the display driver and is unable to continue. The application must close."
this message appears in the taskbar: "Display driver stopped responding and has recovered. Display driver NVIDIA Windows kernel Mode Driver, Version 267.21 stopped responding and has successfully recovered"
any ideas on how to stop AE from causing my display driver to stop working?
Thanks, Ramzi Rebeiz

For anyone picking up this thread (it's probably too late for rrebeiz40 by now!) I have come across a simple but apparently very effective tip that has solved the 'OpenGL driver lost connection' issue for many people using various NVIDIA with various Adobe progs (incidentally a lot of these seem to crop up on Dell machines, especially Notebooks).
(It fixed my issue with Premiere Pro CS4 - GeForce GT 555M on Win 7 Ultimate 64-bit, Dell XPSL702X).
It's posted on http://forum-archive.developer.nvidia.com/index.php?showtopic=5331&st=40 (look for the last post, No 50) as follows:
THIS FIX APPEARS TO WORK...found on an Adobe forum
"This issue led me to this fix: go to NVIDIA Control Panel --> Manage 3D Settings --> Global Settings, and switch "Power Management Mode" to "Prefer Maximum Performance" (the default "Adaptive" setting seemed to be the culprit). And that's it! The key here is changing the "Global" setting, as my individual programs were already set to "Prefer Maximum Performance." I can cause the error to reoccur by changing back to "Adaptive."
Otherwise lots more ideas on this site: http://www.instructables.com/id/How-to-Fix...Nvlddmkm-Error/
My PC has been running for 2 days now. I only put the top fix in for now. Feel happier I have more options if need be though.
Inserted from <http://forum-archive.developer.nvidia.com/index.php?showtopic=5331&st=40>
It worked for me

Nokia Ovi Suite has lost connection with your devi...

5 months has passed and many hours on the phone to Nokia. The phone has been completely reset /reboot by Nokia time and time again and still the phone gets this message when trying to update software..."Nokia Ovi Suite has lost connection with your device"....We were optimistic that the software upgrade would solve the other problems we are having with all the Nokia phones at work. They are all E52's

Having the same issue currently with an E72 software version is 054.005.266.02 and Ovi Suite 3.1.1.80
Actually I had connection lost all the time with all previous versions of Ovi Suite too... it has never been reliable.
Using original Nokia USB cable, connected securely. Tried different PCs, different USB ports, same issue.
Just now I'm trying software update and it looses connection during the backup process all the time... very disappointing. Screenshot attached if anybody is interested.
Attachments:
nokia_conn_lost.jpg ‏40 KB

E5: Ovi Suite has lost connection with your device...

I am trying to update the software on my E5 using OVI suite but I keep getting an error during the install phase (after backup). The following error and instructions are displayed in the OVI suite window but makes no difference when I follow these instructions (just end up back with the same error).
"Nokia Ovi Suite has lost connection with your device. Follow these steps to help reconnect your device:
1. Remove USB cable from your device.
2. Restart the device (turn off and on again).
3. Re-insert the USB cable.
4. Click 'Ok' below to continue updating."
Current E5 software version is 042.007.
I am trying to update to E5 software v. 043.115
Any ideas?

Yep having the same issue. Just got a replacement handset due to the random restarting issue, soon after setting up the new handset I get a message on phone saying software update is available. Both OVI suite and Nokia software updater say version 43.115 is available (about 200mb in size), I currently have the same version as you 42.007. It claims to do a lot of improvements to the handset. The update downloads fine but when it comes to installing I keep getting the same issue. Phone simply will not restart automatically and the update restarts then fails at the same point over and over. Had the same problem with my previous handset.
I spoke with my network provider to see if it was an issue with the handset needing firmware specific to them but they said no it is an issue with the firmware itself and has been happening to everyone since its release!!! They said I should not download it until Nokia has resolved the issues with it. But how do I know when that will happen as I cannot find anything put out by Nokia stating there is an issue or anywhere on web forums saying there is actually a problem.

Disk Utitlity has "Lost Connection" with Disk Management tool"

[ Edited by Apple Discussions Moderator; please start a new topic about your technical issue. ]
Running OSX10.3.8
I installed:
"iTunes" (6.0.2)
"iPod Updater 2005-11-17" ((null))
"iChat Update" (2.1)
Went to repair disk permissions
I get this error:
Disk Utitlity has "Lost Connection" with Disk Management tool" Please quit Disk Utility.
then it says quitting Disk Utility may render the disk useless. Stopping the scan just gives a "stopped by User" red text message in the DU screen.
Had to Quit. No other way out.
Now it will not repair "or" verify Disk permissions at all.
What to do?
Powermac G4 1.25ghz, OS9/OSX Mac OS X (10.3.8)

Getting the same results booting off of the install CD. I even ran fsck -y after a soft boot(command S). Note I also installed the iPod updater and iChat update.
I'm getting a crash log that has to do with DiskManagement
Path: /System/Library/PrivateFrameworks/DiskManagement.framework/Resources/DiskManage mentTool
I tossed the pref file for Disk utility and tried to locate a pref for the Disk Management but nada...
Is there a prefs file that needs to be tossed?
Anyone do a recent Onyx Maintainence cleaning?
Is there a way to do an iTunes Uninstal and reinstall a previous version?
Powermac G4 1.25ghz, OS9/OSX Mac OS X (10.3.8)
Powermac G4 1.25ghz, OS9/OSX Mac OS X (10.3.8)

'Disk Utility has lost connection with Disk Management Tool' w/ RAID 10 set

Using 4 internal drives, I have specified the following setup for each:
2 partitions, 1 'speed' of 5 GB and 1 'data' of whatever remains.
The 4 speed partitions stripe to a single RAID volume correctly.
The 4 data partitions are used to make a RAID 10 volume as follows:
The first 2 data partitions are mirrored to make a 'data-A'
The next 2 data partitions are mirrored to make a 'data-B'
These complete correctly.
Upon attempting to strip data-A and data-B in order to finish the RAID 10 setup, Disk Utility quits with the following message:
"Disk Utility has lost connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility'.
A search here and on the nets reveals only that this message appeared in 10.3.x when attempting to repair disk permissions and had to do with a rogue iTunes support file. This is occurring on a blank system (no iTunes installed) so I don't think its the same cause.
Note that I was able to complete this setup under Tiger several times without issue, so it seems to be unique to Leopard. Does anyone know what is going on and hopefully suggest a workaround?

To answer my own issue and leave a marker here for others, I was able to successfully set up a RAID 10 partition using diskutil, indicating that the problem is Disk Utility itself and not the RAID implementation.
Disk Utility has proven itself to be bugridden (must restart frequently to get updated view of volumes; drops device names at various times; etc.) and this latest bug would seem to suggest that it should be avoided in favor of diskutil for any serious RAID construction.

SAP Server has lost connection to the database!

Hi Gurus,
Can some please guide me on this " SAP Server has lost connection to the database! " what need to be check.
OS : AIX
DB : DB2
thanks
vamsi

Hello,
1)Check if the DB is running.Issue the following command @ the DB-level
db2 connect to <SID>.
2)Also check R3trans -d from the app. server and check for trans.log file for the error.
Hope it helps.
Regards,
Prasanna
Edited by: Kulkarni Prasanna on Jul 24, 2008 3:53 PM

My iphone has lost connection to the server; I cannot get e-mails.

My iphone has lost connection to the server; I cannot get e-mails. What can I do to fix that?

I recently put on a PowerPoint presentation at DU, in Denver Colorado; signed on as DU guest to access Internet link. SInce then I haven't been able to get e-mail on my Iphone - Cannot Get Mail, Server Stopped Responding. I tried all previous suggestions, such as rebooting phone, updating software etc. I went to MacBook Pro and tried logging on to yahoo e-mail. Apparently there was a security risk to my e-mail account so Yahoo locked up my account. I reset my password, it was verified through text message, and Voila it worked. Don't forget you also have to change this on your Iphone: go into settings; Mail, Contacts, Calendars; click on your e-mail browser, then account and enter your new password, click done and it will verify on you phone as well. Hope this helps!!!

WRT160N lost connection

Similar Messages

Maybe you are looking for