WRT160n set up trouble in existing network -help please

It's a small business office. Cable modem comes into a Netgear smart switch, which distributes LAN to desktops and a older Wireless router.
So I hook up the router as directed, setup won't complete... error no router found.
Of course 192.168.1.1 is the netgear switch, so that's not available.
Grr.
I tried seemingly everything. Plugged it into the cable modem Lan ports, plugged it into the Netgear Lan posrt, put it in serial with a computer into the Netgear. Blah.
There's no usb connector to port into.
Ideas?
Thanks in advance!

Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...Under the Setup tab,the router ip address is 192.168.1.1...So change it to 192.168.1.2.Power cycle the entire network and it should work.

Similar Messages

Drop 'N Go subnet within pre-existing network - Help with routing please

Hello All,
I would consider myself entry level at best when it comes to the Cisco ASA 5505, and I appreciate any help or direction that anyone would be able to provide regarding this issue I am having. I am sure there is something out there for this but I have not yet been able to figure this out with what I have found.
So we currently have our infrastructure setup like this: modem(69.14.72.6/255.255.255.248)->ASA(192.168.1.1)->Switch->Hosts and Servers(192.168.0.X\24).
What I am trying to do is drop in a small router somewhere within this network with its own subnet and be able to communicate back and forth to it from the 192.168.0.X network, so it will look something like this: modem->ASA->Switch->Hosts and Servers(192.168.0.X\24) && Hosts and Servers(192.168.1.X\24).
I would like to allow this traffic flow hopefully while only having 2 interfaces configured on the ASA (Outside 0/0, and Inside 0/1-0/5) and without modifying the configuration on the Switch. A few key phrases that come to mind from my search thus far are "Hair Pinning" and "same-security-traffic permit intra-interface". Also I am aware of port-forwarding, and as I understand it this would not be practical as I would have to configure a rule for every device connected to the 192.168.1.X\24 network.
I hope someone will be able to help me with this issue, I have been at this for 3 weeks now.
Thanks again everyone!
EDIT: Here are is a diagram to help explain what I am trying to do. The area shown in red is what I am trying to add to the rest of which I already have.

Hi,
I've made this in packet tracer (I had to use a router instead of ASA - but same principle applies.)
This is the classic "Router on a stick" topology.
Note: You'll need to create a trunk between the switch and R1 now that there are 2 VLANs.
## I've used 192.168.0.2 as the gateway address for the 192.168.0.x network, but you could in fact set up the router R1 with 192.168.0.1 as the subinterface, get everything configured, and then install the router and change the current internal address of the ASA (192.168.0.1) as per my example, at the very last minute. ##
The ASA will need a route added for traffic back to the 192.168.0.x and 192.168.1.x networks.
The 192.168.1.x network -- gateway will be 192.168.1.1
The 192.168.0.x network -- gateway will be 192.168.0.2
*There's no need for any of the subjects you mentioned:
"Hair Pinning" and "same-security-traffic permit intra-interface" or port-forwarding.
HTH
Ian

2nd MBP has messed up my home network--help please

I have a linksys wireless router. I have a MBP 1.83 gz and my MBP 2.2 GZ just arrived today. I turned them both on, both will get onto my wireless network (which is WEP protected) and then after two or three minutes neither computer can go online. Instead of showing a full strenght airport icon (which is normally shown) it shows one bar missing on both computers' airport icon. If I reset the router, I can get on one computer and be online, but as soon as I add the other computer, then I am unable to surf.
I also noticed that if I restart my new MBP I have to restart the router to be able to go on line.
I imagine there is some setting in the router causing this, but my knowledge is very limted. Any suggestions or resources would be greatly appreciated. Thank you in advance and I will be sure to mark your reply as helpful.
Owen Pillion

My wireless router is set up as Automatic Configuration DHCP.
Each computer works fine without the other on. If both are on, my original one works, but the new one cannot get on line.
I do not know how to get the ip configurations of my mac (I wish I did--I dont even know what that is). And I do not know how to see if both are using the same ip address or how to tell the computers to use different ones.
I know that my wireless network has been working fine. I have even used a PC notebook, been able to enter the WEP password, and surf with the MBP on. But with two MBPs--No surfing happening.

IMac / PC networking help please!

Hello
I have a PC with Outlook and an iMac with Entourage and a printer connected. I would like to be able to sync the Outlook calendar on the PC over to Entourage, and use the printer connected to the iMac on my PC.
I have an ethernet cable which I have connected to the ports on both computers and have looked at network settings but am at a loss as to how to set this up.
Is there a quick and cheap way of doing what I want to do with the set up described above?
Many thanks
Martyn.

http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh2054.html
That article pretty much sums it up. YOu have to make sure that you assign the two computers IP addresses that are on the same network and subnet. (10.10.10.1 and 10.10.10.2 for example... subnet 255.255.255.0 on both). Then those instructions should work.
To share the printer look here:
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh1770.html
As for the Entourage/Outlook... I can't help with that but I'm guessing without an Exchange server, you're going to be jumping through some serious hoops to get it to do what you want. Maybe try Microsoft's support site.
Also, connecting two computers without a hub or a router is pretty limiting. You'd be better off buying a broadband router, unless you still use dial up... then I guess this solution is ok.

Routes, gateways, and networks -- Help Please

Hi Linux gurus:
I have a problem that I know you will help me resolve...
I have two network cards in my Linux box.
1. public network:
10/100
192.168.1.102
default gw: 192.168.1.1
netmask: 255.255.255.0
I want this one routed to my router for internet/public use
2. private network 1000mpbs
192.168.2.181
default gw: none
netmask: 255.255.255.0
I don't want this one routed at all. It is used for backups, moving files, etc and is called by individual servers using /etc/hosts.
Now problem is that I can't get out and/or in to the box. It appears as though the default gateway on this system is 192.168.2.254. I set up the network via the gui and it appeared to be working, but alas it is not. It looks like things are only talking via the 192.168.2.X network, and that is not what I want...and from the outside world, nothing at all is talking to it.
Below is my ifconfig -a and my netstat -rn
Please help!
eth0 Link encap:Ethernet HWaddr 00:18:F3:E8:29:2A
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:193 Base address:0x8000
eth1 Link encap:Ethernet HWaddr 00:90:27:AC:7C:4D
inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5339 errors:0 dropped:0 overruns:0 frame:0
TX packets:1891 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:588251 (574.4 KiB) TX bytes:530473 (518.0 KiB)
eth2 Link encap:Ethernet HWaddr 00:0F:B5:43:16:D0
inet addr:192.168.2.181 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:300106 errors:0 dropped:0 overruns:0 frame:0
TX packets:617831 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:28009736 (26.7 MiB) TX bytes:585354764 (558.2 MiB)
Interrupt:217 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:816528 errors:0 dropped:0 overruns:0 frame:0
TX packets:816528 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:102034952 (97.3 MiB) TX bytes:102034952 (97.3 MiB)
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2
0.0.0.0 192.168.2.254 0.0.0.0 UG 0 0 0 eth2

Ok...I did the following:
route add default gw 192.168.1.1 eth1
route delete default gw 192.168.2.254 eth2
I am able to get out to the outside world and it seems to work fine, but just curious:
1. How do I keep this from reverting again? (I could put this in my own script, but would rather not hack it, but do it right)
2. Are my routing tables below correct now (it works I understand, but want to ensure it is done correctly).
3. What is this route for (in the below table) and is it needed?
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2
4. Since i'm relying on /etc/hosts files for the systems on the 192.168.2.X interface should there even be a route for this subnet?
updated routing table:
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1

Set up Lightroom for my workflow - Help Please!!

Hi Guys,
(PC/Win XP pro/Lightroom 1.3/PS CS3 running on large PC with plenty of everything!! - Printing on 7880 Epson through qimage)
I have been working on Bridge/CS3 and want to set uplightroom for the following workflow (easy in Bridge but I cant seem to figure it out in LR).
I want all raw images to reside in a folder on HDD (say jane smith wedding). (that bit is easy- even I could manage that!)I want all work files (Xmp or whatever) and all developed images (low/high res) to reside in the same folder (there was a simple command in bridge - export to same location - that could be set as default but I cannot find in LR.)
I also need to export a jpeg crop ( I cant find a crop tool for inches!!)of my corrected image at say 10x7@ 240dpi for inkjet printing through Qimage and a second jpeg say @ 70dpi with copyright mark for a slideshow in proshow gold.(is there a setting for "save in same location with work files). So I would end up with a folder for example R/jane smith wedd with subfolders develops and previews. This folder should contain ALL workfiles so when i archive ALL files go with it. ( also I would be able to open the raws with corrections applied on a home computer with CS3 but not lightroom running.)
I admit Im thick!!
Any help would be really appreciated, nigel
PS: Memo to Adobe: What were you thinking of with no way to save contact sheets.......? Also no way to export music with the slideshow......?

1. You need to turn on "automatically write XMP" in preferences. Then the settings data will be saved as you make changes in LR and CS3 can use these settings to open images. You could also convert to DNG for the same end result.
2, If you want your exports in the same folder then just select that folder in the export dialogue. You also have the option of creating a sub folder to store the exports in. It doesn't have a save to same location default but it's not such a pain to pick a folder. I actually send my edits to a different drive just in case of corruption.
3. There's no cropping done by the crop tool so you can't assign a dpi to it. Crop it the way you like it (you can set an aspect ratio if you like. Nothing happens until you export and that's where you select dpi, watermarking etc for output files. In the export dialogue just enter the settings you want. You can also save several sets of output settings for quick retreival later on.
4. To save contact sheets install a free PDF printer and just print the contact sheets to it. Mind you because Adobe wont let you select sRGB as an output space and insists on Pro Photo RGG (don't get me started...) the colours will be washed out and horrible. You can also save your contact sheet settings so redoing it really isn't that big of a deal. Printing and saving contact sheets worked really well up to 1.1 after that Adobe broke it and it's the thing I miss the most. All they need to do is allow us to select an output colour space when using printer managed printing so I can have sRGB printing back.
Don't know about the slide show thing, sorry.
Hope this helps
Gordon

Having trouble with quicktime. Help please.

A while ago, maybe a few months actually. My quicktime stopped working so i uninstalled it and installed it again. Now whenever I go to a website where I need quicktime to see videos, I only hear the audio (e.g Apple websites, guided tour videos, audio only). What can I do to fix this problem.

These forums can somtimes be helpful, but after a lot of reading in this case, I'm stumped.
No help starting, then quitting GarageBand, no help setting MIDI audio output to 44100 Hz (it was already there), no help reinstalling QT 7.0.4, no help rolling back to QT 7.0.1, no help shutting down all other applications when running QT. OS is current, with no more available updates. The video I edited on this same computer using Quicktime and posted on putfile plays fine on my (gasp) older PC running Windows QT 7.0.4.
As a loyal Macintosh owner since 1984 (my family currently has 7 working Macs, 3 iPods and 1 PC), I have the sinking feeling Apple seems to be becoming less unique and more microsoft like over time. While MS isn't up to the level of Apple yet, the gap seems to be closing. I don't want to know how to change my audio settings, repair permissions or do anything not directly related to the task at hand. I'm getting tired of paying for "upgrades" that aren't, including the new iLife suite and the QT 7 pro key I recently bought.
How do we report this issue? I encourage everyone who is having problems with Quicktime videos stuttering, dropping video or audio to report this so that Apple will be made aware and held responsible.
PowerBook G4 1.33 GHz Mac OS X (10.4.5) 1.25 GB Ram

Adobe Programs: Conflicts and Networking help please

I don't know if this is the proper place to post but this is what I'm looking for. Any suggestions, thoughts or help would greatly be appreciated.
We are researching the possibility of using an outside IT Consultant for our computers and Adobe Software. Our IS team (about 10 people), while very good with networking PCs, are not familiar with Adobe software and how they interact with the hardware/computers and networks.
We have been struggling for a few years to get our machines to be at their best performance and efficiency, especially on large tradeshow graphics. We have had crashes and glitches since CS3, but we understand that their are many variables and they are not just Adobe product issues.
We are a large company but have only 3 designers. So we are trying to find our own help and do some of our own research on a resolution.
We are looking for someone who is PC mainly, but if you have a recommendation for anyone that networks macs also that would be great. We are currently on PCs with hopes of someday moving to macs.
If anyone knows of any business or independent contractor in the North Central Florida area please let me know.

We contacted Adobe but they said they can only give over the phone help and will not refer us to anyone.

CS5 Win7 Networking Help Please

I'm a home-based designer who needs nework help. I have CS5 Master Collection on a Win7 (Home Prem) computer which is peer-to-peer networked with 2 other Win computers (98 & XP). Win Exporer has no problem navigating anywhere on the network from any computer. However, Bridge CS5 on the Win7 computer (i5 cpu, 2.7GHX, 8GB Ram) shows "Lock" icons on all network locations; hangs when any network location is selected. Also hangs when launched from within Photoshop, Illustrator, or InDesign. I've searched these forums and tried various fixes having to do with security, permissions, firewall rules, clearing caches, etc. No luck. Adobe Support won't help me as it doesn't cover "network issues" such as mine. Their enlightened suggestion was to "move the files you want to browse onto the computer where CS5 is installed." Any real suggestions from anyone would be greatly appreciated. I'm not a programmer but I can usually doink my way to understanding.

Steve— Thanks for your suggestion. I didn't think to remap shared network folders, duh. (And even after Win7 Explorer forced me to do it to become part of network!) Previous versions of Windows allowed me as "owner" (administrator) to see, read, and write out of the root directory and all the other hard drives installed on networked computers. Win7 apparently doesn't or discourages it, even on the older computers, it seems (at least for amateur net administrators like myself). From Win7 Explorer I can and did remap target directories on the remote drives located on my Win98 and Win XP computers. Unfortunately now BridgeCS5 (on my Win7 computer) shows these remapped icons with big red "X"s through them. But these remote directories can be browsed and files manipulated. I still can't get BridgeCS5 on the Win7 computer to open from within PS, AI, or ID. But MiniBridge now works from within PS. If you have suggestions for fixing this BridgeCS5 functionality in AI or ID I'd appreciate it. I'll revisit your knowledge base and forums for this info because I'm spoiled by the way BridegeCS3 works on my WinXP computer. Otherwise I'll find ways to use Bridge outside of AI, ID, and the rest. Thanks again for helping me to get MasterSuiteCS5 to more closely fit the way I work. —Phil Smeiles

Home networking help please

My new iPod has lead me to quickly fill the hard drive on my laptop. I've looked at the options for how to address this and have decided a wireless home network is the answer. I think all I need is an old PC (c. P3 1GHz) with a big hard drive and a wireless card and a bit of time to set it up.
I've never considered this before and it will definitely be stretching my technical skills, but I'm ready to learn. Can anyone recommend a good guide as to how to get started and just what I need to do? I seem to be able to buy what I think is a suitable spec tower PC for c. £100 and a new 250gb hard drive for £90. Am I being naive thinking it's this straight forward?

Why not simply get a USB or FireWire removable drive?
Gonna be a zillion times easier. Simply plug it in.
No need to have to mess with another computer, OS problems, networking problems, wireless cards, etc.
100 quid for 300 GB.
eBay UK External HArd Drives

Apple Remote app on wired network: help please

I am trying to use the remote app to control my apple tv. I noticed that my bedroom apple tv unit was showing up in my app but not the living room apple tv. After further inspection I found that the ethernet cable was not plugged into the bedroom apple tv unit so I was on wifi to control the apple tv.
We do a lot of streaming in my house and having 4 apple tv's on wifi would just kill the streaming. From what I see, the device(iPhone) using the remote app and the Apple TV you want to control have to be on the same wifi network.
Is there a way to use the remote app when the apple tv's are connected via ethernet cable? They are still on the same network but the app doesn't recognize them if they are on ethernet.
Basically if I unplug my ethernet cables from the apple tv's the app works but when the ethernet is plugged in the app doest see the apple tv's present. Any way around this issue>

I am definitely on the same network. After about an hour I finally got it to work. My apple tv was plugged into my apple wifi router which is connected to a 24 port switch. I connected the apple tv directly to the switch and it came up instantly. I then plugged it back into the apple router and it continued to work. I am not sure why none of the apple tv's would not initially work when plugged in directly to the router since it is the same network. So I did this to all the apple tv's and they are all now working.
Home sharing was enabled on all the apple tv's. The only thing I did was connect to switch first(got a good connection via the app) then reconnected it to the apple wifi router.

J6480 wireless and network help please!

I have an officejet J6480 that has an error in printing system when printing wireless. Everything is configured correctly and my printer reads the router and connects. If this problem cannot be fixed, can i use an ethernet connection directly from printer to router and get it to work. I tried this but also got a failure to print message. Please help asap! Thank you

hello,
first, cancel the print jobs
then try to restart the print spooler of the computer (click start>run... then type services.msc)
look for print spooler in the list
right click on the print spooler and click restart
if that doesnt work, then do a partial reset on the printer
unplug the power cord from the back of the printer without pressing the on button
press and hold # and 3 and wait for 10 seconds
plug the power cord back
wait for the printer screen to lit up then release the # and 3
try to ping the printer
try to print a test page again
keep me informed..

Setting Up New 3GS - Dilemma! Help Please!

I got my new 3GS from Orange today.
My previous iPhone was a factory unlocked 3G from Italy running on Orange.
I inserted my new SIM card, plugged the phone into my iMac and completed registration via iTunes.
I have not actually activated my SIM card with Orange because they're closed until 08:00 tomorrow but the 'phone is "operational" because the on-slider is there, all the icons are there and my 'phone number is shown correctly in iTunes.
Here's the bit that worries me:
In iTunes the page states: "An iPhone has previously been synced with this computer". It then gives me 2 options: (1) Set up as a new iPhone. (2) Restore from the back up of Joe Bloggs iPhone.
I want all the features that come with a "legal" iPhone contract, I want to keep my original 'phone no. which I've had since 1996 and I would prefer not to lose all of my calendars, contacts, purchased applications etc.
Which of steps 1 and 2 above do I select and do I need to still activate my SIM card with Orange?

Restore from your backup & you should be fine.

My macbook pro decided to give a different res and a horizontal line follows my cursor (like a diagnostic mode or something) i have shutdown/restrted. Fixed the res but the cursor problem still exists any help please.

I was using my mac as normal and then my resultion on mr screen changed which i have fixed using the normal methods but i still continue on getting a horizontal line whereever my cursor is even after i have restarted and shut down. The line is a white colour but my other screens seem dulled wherever this line is not following it is not a solid white. It looks like its in a diagnostic mode or somthing. Any help would be appriciated, thanks.

It is possible there is a problem with the computer's graphics, but try a simple fix. viz. reset the NVRAM / PRAM.
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

Trouble with some code help please

i need help with this program i have to do a webclient in java i will put here the instructions that were given to me and then the work i have been doing so you can have an idea of what i'm doing any help you give me i will be very thankful thanks.
Here are the instructions
The class WebClient will represent a simple web client. This class must provide the following functions:
1. connect to a web page using a URL
2. obtain or get the response from a server
This funcionality will be provided by the public interface of the class:
- WebClient( )
Creates a new object of the class
- void setURL(String url)
Used to indicate the URL of the web page
- String getResponse()
Gets the response of the server to the page who's URL was indicated(Example of a response: HTTP/1.0 200 OK)
You have to implement the following:
1. The class WebClient with an public interface that Includes the methods specified upwards, in a file called WebClient.java
2.A class WebClientTester, in a file called WebClientTester.java, with a main program that minimun have to:
a) Create a instance of WebClient
b) Using 3 valid URL's
- Invoque setURL to indicate the URL of the server
- Invoque getResponse to get the response of the server
- display in the console the response of the server
c) Using 3 invalid URL's (this is the correct server but the page does not are on the server)
- Invoque setURL to indicate the URL of the server
- Invoque getResponse to get the response of the server
- display in the console the response of the server
As a tip they give me that i can use the clases HttpURLConnection and URL to implement WebClient. It is recommended to save the URL in an instance field of WebClient.
Those are the instructions now i will write here what i have do until now
This is the WebClient Class:
public class WebClient
     public String Wecli;
     public WebClient()
          Wecli = new String();
     public void setURL(String url)
     /** need code here */
     public String getResponse()
     /** need code here */
     public void display()
          System.out.println(Wecli);
what i need there is the methods constructors or whatever are so that setURL and getResponse work and do what are suposed to do.
Here is The WebClientTester class
public class WebClientTester
     public static void main(String[] args)
          WebClient wbcl = new WebClient();
          wbcl.setURL(http://www.nba.com);
          wbcl.getResponse();
          wbcl.display();
          wbcl.setURL(http://www.mlb.com);
          wbcl.getResponse();
          wbcl.display();
          wbcl.setURL(http://www.msn.com);
          wbcl.getResponse();
          wbcl.display();
     wbcl.setURL(http://www.nba.com/baseball.html);
          wbcl.getResponse();
          wbcl.display();
     wbcl.setURL(http://www.mlb.com/basketball.html);
          wbcl.getResponse();
          wbcl.display();
     wbcl.setURL(http://www.msn.com/practice.html);
          wbcl.getResponse();
          wbcl.display();
that is basically what i think i need so that the program works any other help you can give me will be very useful thanks for reding it and give your opinions.

Those are the instructions now i will write here what i have do until nowLooks like you've posted your homework instructions, done less than the bare minimum to make it look like you thought about this problem, and now you want strangers to help you cheat by giving you the code that does the work so you can hand it in as your own.
%

WRT160n set up trouble in existing network -help please

Similar Messages

Maybe you are looking for