WRT160N V3 connection lost during uploads

I've got a WRT160N a few months ago and have then been facing the problem that, whenever I upload files with large sizes, e.g. a few MBs, through email, or Flickr, the connection between my iMac with the router (Wireless, N) would be lost, and the upload would not be successful.
I've upgraded the router's firmware to V3, but it doesn't help.
What can I do...? I don't know much of the settings in fact.
Thanks.
Solved!
Go to Solution.

Login to your Router setup page and below change the MTU size to 1350 and click on Save Settings, Then click on the Wireless tab and below click on the sub tab Advance Wireless Settings and below Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2307 >>Click on "Save Settings"...
Now you can try to transfer the file between your iMAC and Router...
If still face the same problem, since you have uploaded the firmware on your Router, then press and hold the reset button on your Router for 1min and then unplug and replug the power to your router after 30sec and then re-configure all the settings on your Router from scratch.

Similar Messages

Network connection lost during sleep

Each time sice upgrade 10.8.2 network connectopn is lost during sleep

Hi
I have the same problem. After waking up the MBP from sleep, my connection to my external Volume via AFP is lost. (ML 10.8.2.)
Though i checked a lot of forums, but didn't find out how to solve this problem.
I hope, somebody will find a solution …
Cheers
Alex

Connection lost during facetime

connection lost in facetime after upadating to iOS 6. what will i do?

Hi, i am having the same problem with my ipad 2.. after updating to the io6 on both ipads (mine and my dad) i am unable to facetime with him.. it says "connecting" and then 5 mins later it says "connection lost" CALL BACK!
I am beyond frustrated as i never faced any probs before the update!
Some one please help!

Character set is lost during uploading file to blob?

Hi!
When I upload file from a disk to htmldb_application_files it is stored there as a blob. Then when I convert this blob to clob, with proper character set id as a parameter, characters in clob are not correct. They loose seriffs etc.
The question is : What happens with characters during uploading to blob?
Thanks!

Hi!
When I upload file from a disk to htmldb_application_files it is stored there as a blob. Then when I convert this blob to clob, with proper character set id as a parameter, characters in clob are not correct. They loose seriffs etc.
The question is : What happens with characters during uploading to blob?
Thanks!

IP connection lost during Upgrade MDS95XX NX-OS

Hi
During upgrade MDS95XX from 5.2.2 target 5.2.2d we lost IP connection because of bad configuration IP of HA Standby Supervisor.
Is there a way to verify IP configuration of standby Supervisor before upgrade ?
Best regards

you can do "system switchover" from active to standby, then ping standby if it is response

Connection lost during minutes

Hello,
thanks in advance for your replies
the problem is that we lost the connection during some minutes with the server .The ping is right but we are not able to login to
the server or open SAP sessions.
could youy help me please
Thanks

nana85,
What was the resolution for this issue. I'm getting the same errors in the SM21 log, but have not had any user complaints.
08:22:59 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050
08:35:22 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050
08:35:31 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050
08:35:31 DIA 000 000 SAPSYS                Q0 2 Stop Workproc 0, PID 28497
08:35:34 DIA 000 000 SAPSYS                A1 0 Initialization complete
08:36:28 DIA 001 000 SAPSYS                R4 7 Delete session 001 after error 050
08:49:11 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050
08:55:31 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050
09:06:18 DIA 002 000 SAPSYS                R4 7 Delete session 001 after error 050
09:06:54 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050
09:06:54 DP                                 Q0 G Request (type NOWP) cannot be processed
09:07:32 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050
09:07:40 DIA 000 000 SAPSYS                R4 7 Delete session 001 after error 050

Ethernet connection lost during migration

The ethernet connection gets lost while attempting an initial migration from an iMac 10.6.2 to a MacBook 10.6.1.
Supposedly, there are some advantages to doing a migration during the first set-up process.
Following the prompts on the new MacBook to connect an ethernet cable to the older Mac, then open Migration Assistant.
Shortly after entering the Administrator password and the code number from the new MacBook the connection is lost.
Maybe there never was a connection, how would I know?
Tried two different cables, could they both be defective?
Anyone have experienced this problem and know the solution?

R C-R
Thought that you would be interested to know that your thoughtful and appreciated suggestions made no difference in eliminating the connection failure messages.
The MacBook is new. No one has ventured past the Welcome process. One of the first options after selecting language, country, & keyboard is the option of migrating information from another source. I chose to migrate From Another Mac.
The window instructions state to connect the two computers with an Ethernet cable, which I did.
Open the Migration Assistant in the iMac. Followed the instructions in the windows.
The iMac recognized the MacBook and a passcode appeared in the MacBook window.
The passcode was entered in the iMac, and the gathering of information begins in each computer.
Then the drop down window with "The Network Connection Failed" appears first in the MacBook then the iMac.
End of migration process.
Anyone have this problem or a solution?
The manual accompanying the MacBook says:
"*Gigabit Ethernet port
Connect to a high-speed Ethernet network, a DSL or Cable modem, or another computer. The Ethernet port automatically detects Ethernet devices and doesn't require an Ethernet crossover cable."
I definitely had these two computers directly connected with a working CAT6 Ethernet cable.
What am I doing wrong?

N96 V20 Update: Connection Lost during OTA update ...

Ok, I decided to update my N96 thru OTA this time. I chose "Check for New Updates" from the phone's menu but while checking if there was a new update, the phone told me "the connection was lost!" with the WLAN modem.
I am now little concerned about using OTA. What happenes if this happens right in the middle of "updating process?"
I wanted to try NSU but this time NSU said the latest firmware was still "V12". No luck there either. I guess V20 isn't widely available around the world yet, or is it?
I don't think NSU would tell me that there was no V20 available yet, where there really was.
By the way, my phone is purchased directly from Nokia (unbranded, no operator branded.)

The update may not be available on NSU yet for your product code
One of the cool things about updating OTA rather than via NSU i sthat if the connection is lost, not only does it not crater the phone, but you get the option to resume your download from where it left off rather than the begining

Connection Lost during update::solutions

I don't want to give you guys false hopes and tell you that this is a surely working fix. Just try these and if none worked, keep digging. If you have more "solutions" add them here.
To all who have this issue, I have tried to fix it since last year by trying to update my N86. Then last night, when Belle was rolled out, I had it again while trying to update my N8. Same issue, but I fixed it. I've been trying for 8 hours and these are some of the solutions suggested on the web (but none worked for me):
> wait for 15 minutes (I've waited for 30, nothing happens. Stop wasting your time and proceed!)
> remove sim/memory card
> connect with Mass Storage mode
> soft reset (also suggested were hard reset, but I think that is best left as a last resort)
> turn off your firewall, and possibly even your security software
> get the latest Suite (I know Nokia keeps repeating this, but I can't believe how many people just ignore this even if they have the older versions)
> delete the 20019119 (not sure) folder in Mass Storage drive under 'private' folder
> restart your computer (worked for some)
> run Nokia Suite as administrator (worked for some)
> redownload the firmware by going to C:\ProgramData\Nokia\Nokia Suite\.....\Variants\ and rename the device folder (eg. RM-596 to RM-596elop), Nokia Suite will redownload the firmware and waste more of your time. Go grab a drink. Preferably coffee, to keep you awake.
> do an online scan for malware/trojan/whatever-not-good, and clean them
Those are the "solutions" I've tried, and failed to see any results. Lastly, THIS WORKED FOR ME.
USE ANOTHER COMPUTER.
or try using another user account and guest account for those who don't have another computer.
Yes, that's it. Funny right? Turns out Windows can mess things up but puts the blame on Nokia phones. Just get another computer, don't sync with it, but just let it back up. If you have a slow connection to redownload the firmware, then just go to the said directory above to copy the file into the new computer. Nokia will detect it (make sure it's in the same folder as in the original computer) and proceed. Good luck to you all!
*Issue on security code during installation is that Nokia Suite will say do not touch your phone even if it asks for language selection or security code. It just asks to enter PIN when phone asks for it. But I've noticed after the first reboot, the second reboot won't proceed until you enter your security code! If you just leave it, it wouldn't reboot the second time. That's the only issue I have during installation. Hope you guys get it!

Finally, I got it to work!
Read the tip from designrs187, didn't read the addition at first, so I went to the hardware section on the control panel, clicked on 'Nokia USB phone parent' and told Windows to look for updates. It updated the driver after which installation of the update finally started!
Guess it does the same as the tip I intended to use.
Man, I hate this Nokia BS!

Database connection lost during running report

Hello Experts, Our environment is WINDOWS2008 SERVER / ORACLE 10G / ORACLE REPORTS.
The problem we are facing is , while running one of the particular reports which runs oracle reports , connection to database server gets lost. Acturally the form is printing a
bar code label, this is performed by running oracle reports runtime 10g. I dont know what is the reason the database connectivity gets lost from reports runtime engine. But the form runtime engine working fine without any database connectivity issue. Kinldy help me to resolve this issue. thanks

Please, close this thread and open a new one in the correct forum.
Reports

Database connection lost during report

Hello Experts, Our environment is WINDOWS2008 SERVER / ORACLE 10G / ORACLE REPORTS.
The problem we are facing is , while running one of the particular reports which runs oracle reports , connection to database server gets lost. Acturally the form is printing a
bar code label, this is performed by running oracle reports runtime 10g. I dont know what is the reason the database connectivity gets lost from reports runtime engine. But the form runtime engine working fine without any database connectivity issue. Kinldy help me to resolve this issue. thanks

Hi,
1- what is the Reports version being used?
2- What is the error you are getting?
3- Have you tried to enable reports trace and see what is happening in trace file?
Thanks, Roberto

Bluetooth connection lost during sleep

Intel iMac frequently loses its bluetooth connection with a magic mouse during sleep and doesn't re-connect upon waking up. A restart is used to re-establish the bluetooth connection. The iMac is a late 2012 model (2.7 GHz Intel Core i5, 21.5 inch screen).

as a workaround then I suspect that turning off the mouse and back on again will make it work
windows 8.1 have the same issue with my razor mouse not with my magic trackpad though
I disconnect the razor mouse and reconnect and all is good quicker then reboot

When wireless connection lost during surfing, firefox will not access the internet after connection is restored.

While surfing the net on my laptop (windows vista home premium, all updates current), if the wireless internet connection is lost while a page is loading, firefox will NOT connect to any websites at all when the connection is restored. Also, if I try to shut down firefox, it will appear to close, but if I try to re-start it again, it will tell me "firefox is already running", even though it's not. I try to go to windows file manager and shut down firefox.exe manually, but even with that it will not shut down, it's like it's stuck in some sort of "loop". The only way to recocile it is to completely re-boot the system, which takes forever, because firefox.exe doesn't want to shut down even in re-boot.
== This happened ==
Every time Firefox opened
== Always with firefox. And firefox is up to date ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; .NET CLR 3.5.30729; .NET CLR 3.0.30729; .NET4.0C)

No it does not work, uninstalled both McAfee and Firefox and only reinstalled Firefox alone, still did not work. I have now both reinstalled and am still unable to connect

Internet connection lost while uploading pdf file !!!!

I'm using adobe reader XI, I'm noted that while i'm uploading pdf file, my internet connection will be disconnect. I have contacted adobe help desk team they only informed me to contact adobe forum. I have this issue for past week. Awaiting for your reply.

I had a very similar problem which I fixed like this:
1) Move the file /Library/Preferences/SystemConfiguration/com.apple.airport.preferences.plist to your Desktop.
2) Reboot
Snow Leopard will rebuild this file from other info.
This sorted out all my won't connect/loses connection issues.

Connection lost during saving some workbooks in Plus

Hi,
I've faced strange problem in Disco plus. When I try to save some workbooks to database, connection is lost. This problem is faced on some workbooks, in other saving works fine. This problem doesn't exist in Desktop edition.
I've searched forum and found, that it could be connected with sorting on calculation item based on CASE. But I haven't any calculation and for test removed all sorting and problem remains.
How do I can solve this problem?
Regards,
Krystian

Hi Krystian
Presumably you are on 10g? I'm wondering whether you created the workbooks in Desktop initially and then started using them in Plus. I noticed that this scenario was causing workbooks with calculations to not save or reopen correctly. When I created the workbooks using only Plus I had no issues.
Can you also confirm whether you have upgraded to 10.1.2.2 recently? There are known issues with lost connections here too.
Best wishes
Michael

WRT160N V3 connection lost during uploads

Similar Messages

Maybe you are looking for