WRT160n V3 wirless connectivity problems?

Recently i have been having problems connecting to my wireless connections. I have one pc that uses a wireless N card (internal, laptop) and i have one that uses G. Both laptops have been having connection issues, and its intermittent. I have several other devices that connect fine. When i unplug the router or about 3 seconds and plug it back in, it reboots fine and im able to connect fine. I have also updated to the latest firmware but no changes. Any ideas on what is causing this?
Regards,
Howard

As I have mentioned, there might be other devices or network that interferes with your network. Try Channel 1, 6 or 11. If the issue persists after trying each channel, try to reset it to default and start the settings from scratch.

Similar Messages

  • WRT160N v2.02 connectivity problems

    using Windows Vista 64bit, Local cable company DSL, WRT160N v2 upgraded firmware to 2.02.  Router so far just straight wired connection to pc.
    My problem is that setup was fine, internet works.. then all of the sudden it doesn't.  I'll open Firefox, won't load any pages.  I open Internet Explorer, won't load anything.. then later on it does.  The network tray icon (two monitors and globe) will just report "ACCESS: local" at that point. Without me even doing anything.  So basically the router chooses when it wants to work.
    I've read through the forums, changed the frequency to channel 11 (just in case the cordless phone messes with it, but I am not even using the wireless aspect yet)..  Firmware is updated to the latest..  lights all seem normal.
    another question i have is.. is there a way to split the DSL modem output so that in case the router acts screwy, the main computer will still have internet?   I'm basically going to use the router for downstairs internet and for an xbox360.  Sure it'll be annoying to lose internet downstairs, but upstairs this main computer is important to always have internet working.
    thanks in advance

    Hey try resetting the router reset button in such a way that power
    light is blinking on the router & then do a complete network power
    cycle i.e., unplug the power cables from the modem & from the router & then plug in the power cable to the modem first once all the lights are
    solid green you could plug in the power cable to the router & check out
    it will definately work!!
    Open the setup page of router using 192.168.1.1 then put in the
    password as admin...all you need to do is do the wireless settings such
    as Radio Band Frequency to Standard 20 MHZ frequency,channel to 11.
    Also,the advanced wireless settings to Beacon Interval=50,Frag
    thres=2306 & Rts thres=2307 & then uncheck a Block Anonymous Internet Requests & it will definately work!!!

  • Wirless connection problem

    hello. we have 3 computers in the house. none is able to connect to the wireless connection of the printer. The printer is an officejet 4500
    http://gyazo.com/d556e5c68818293e142290e414d8746c
    here are my router settings. Thanks to all help.

    Download and run this utility:http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&jumpid=ex_r4155/hho/ipg/ccdoc/p...
    What does it say?
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • WRT160N Internet Connection Problem

    I have Verizon (non PPPoE) DSL.
    Using a very old Wirespeed 2100 Modem and a WRT160N everything connects. However the Wirespeed 2100 Modem does not support ADSL2+
    So I have tried two ADSL2+ Modems - a Westell 6100G and a Zoom ADSL2+ 5715. The 6100G has been put into bridge mode and has worked in the past with another router. The Zoom 5715 is a bridge modem.
    Both ADSL2+ modems light up their DSL lights showing they are seeing and syncing with the dsl - however the WRT160N does not get an IP address with either and I have no internet connection. I know Verizon would require MAC cloning - however in this case the MAC is always coming from the WRT160N and therefore should be the same irrespective of which modem I use.
    If I put the 2100 back in place everything work again - the WRT160N gets an IP address and and I have an internet connection.
    I would like to get the WRT160N to get a IP address through either of the ADSL2+ modems so I can (hopefully) get a faster connection using ADSL2+
    The reason I suspect the WRT160N is causing the problem is the 6100G has previously worked fine with another router (which had the MAC cloned to the same address as the WRT160N). For a number of reasons the other router is no longer an option.
    Ideas?

    As per the concern you explained that you wanted to get a faster connection using ADSL2+.... So for that could you tell us how you have connected the a Westell 6100G and a Zoom ADSL2+ 5715.... What is the IP address that you get from the modem.... 
    As in your post you said that your ISP ( Internet Service Provider ) is Verizon (non PPPoE ) DSL.....
    So how is your modems been configured in bridge mode....
    If these are in bridge mode than in that case have been provided by any username and password by Verizon....

  • WRT160N Dropping Wireless Connection.

    Hey, I was wondering if anybody could give me some advice on a problem I've been having. I just recent bought a WRT160N as an upgrade to my old D-Link DI-514, I wanted to have faster wireless speeds. My new router does have much faster speeds, but the wireless connection keeps dropping. When this happens no computers can connect through the wireless, and I have to physically powercycle the router. Sometimes it will completely freeze up and not even allow wired users to access anything. There are only two computers connected to it, and I was wondering if anybody has experienced a similar problem?
    One possibility I have consired is that it cannot support the number of current connections I have open at the time, but I find that hard to beleive considering my old el cheapo router had no problem handling the same thing. Does anybody know the number of connections it can handle at once?
    I'm pretty sure it's not an interference issue, I've tried lots of different channel options, and when I've seen interference problems before it wouldn't lock up the whole router.
    My current configurations are as follows:
    WAP2 Personal,DHCP,MAC Filters,VPN enabled,three applications port forwarded(to wirelss PC), and everything else is default.

    The linksys wrt160N dropped the internet connection.........
    Oftenly my WRT160N is losing connection to all wired and wireless computers in my house (2 wired, 1 wireless).
    Means I cannot connect to internet
    My solution:
    - only use the linksys wrt160N as an accespoint : don't use the internet port on the router !!!
     ONLY USE THE Ethernet ports (1, 2, 3, 4) for ALL your network traffic
    - disable DHCPserver on the wrt160N
    The DHCP server/internetport causes the problems on the wrt160n, so the router dropped the wired/wireless internetconnection).
    The DHCP server on the modem/router works good, "he is the boss in your network"  : disable the dhcp-server on the linksys wrt160N, it can conlict anymore and don't want to be the boss anymore in your network.
    One DHCP-boss in your network is enought !
    Setup:
    router ip = 192.168.1.9
    DHCP server --> disabled  (don't forget !!)
    Wireless: Manual
    BASIC WIRELESS SETTING :
    network mode = Wireless-G only ( my laptop has G ... and no N)
    Networkname (SSID) = PIETJE&puk (example)
    standard channel = 11 - 2.462GHZ (no conflicts with my DECTphone anymore)
    SSID broadcast = disabled
    WIRELESS MACFILTER (OPTIONAL) : ENABLED
    access restictions= permit PC's ....
    mac adres list = < wireless macadres laptop/pc >
    administration:
    router password = THis&4evER (example of storng passowrd )
    (wireless)remote access = disabled

  • Timeouts and connection problems after 5.1(2) upgrade

    AIM/chat and some other programs are having timeout/connection problems after upgrade to 5.1(2). I am using S241 also. The connection problems stopped when the IPS was set to bypass. Rebuilt IPS and left sigs at default settings and problem is still happening. I am not seeing any of the IPs that are having the problem in the Event Viewer or on the Events in the IDM.
    Any known issues with the 5.1(2) that would cause this type of problem?

    I don't know specifically, but I did notice that 5.1(3) was released today.

  • Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

    Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

    Hello Sue,
    I have an iPad 3, iPad Mini and iPhone 5S and they are all sluggish on capitalisation using shift keys. I hope that Apple will solve the problem because it is driving me crazy.
    I find using a Microsoft Surface and Windows 8 phone, which I also have, work as well as all the ios devices before the ios 7 upgrade.
    It has something to do with the length of time that you need to hold the shift key down. The shift key needs to be held longer than the letter key for the capitalisation to work. For some reason, this is a major change in the way we have learnt to touch type on computers. I am having to relearn how to type!
    Michael

  • RFC Receiver adpater Connection problem , Help us to solve ?

    Hi  Friends ,
                          Our scenarilo is Mail to RFC. It was running fine. In RFC Receiver adapter i have given <b>Maximium connection property to 1</b> .
                      While multiple set data passed to rfc will connection problem will come ?
                     Most data not uploaded . I am getting the following error.
                     <b>   If i set max connection to 5 . It is 5 times or more than that it is pusing the data .</b>
                    i am getting the following error <b>while i set the Max   connection to 1 .</b> . <b>Any other place i need to change configuration ?</b>
                   <i><b> - Error: 2007-09-24 10:51:22 GMT-05:30: Message processed for interface YRFC_EXT_WARR: com.sap.aii.af.rfc.afcommunication.RfcAFWException: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException: resource error: could not get a client from JCO.Pool: com.sap.mw.jco.JCO$Exception: (106) JCO_ERROR_RESOURCE: Connection pool RfcClient[CC_EXTE_WAREN_2W_RFC_RECEIVER]e7fa21f86ec535e883636c0beffc0f0c is exhausted. The current pool size limit (max connections) is 1 connections.</b></i>
                            Please give the description . I have referred many likns . Help us to solve this problem .
    Regards.,
    V.Rangarajan<b></b>
    Message was edited by:
            ranga rajan

    Hi,
    Have a look at this.This will help you.
    1.
    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f3f93ee7-0c01-0010-2593-d7c28b5377c2
    2. https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/3103eb90-0201-0010-71af-be6f4a6f61d1
    Regards,
    Akshay Jamgaonkar.
    Reward points if find useful.
    Message was edited by:
            Akshay Jamgaonkar

  • Unending connectivity problems -- and Desktop Help...

    I'm wasting so much time on connectivity problems that it's positively wearying. Prior to the installation of BT Infinity here in April, I had a low quality broadband service because of the length of the line from the exchange: if I could get a download speed of 1.2Mbps and an upload of a quarter of that, I was doing well. 
    BT advised that thanks to fibre optic, my Internet should run much faster. So we had Infinity installed. I'm registered with Speedtest.net so am able to see my performance record.
    The average download speed is now aroun d 6Mbps and the average upload, more than that at 7Mbps. How an upload speed can consistently be faster than a download escapes me.
    But I'm not familiar with the ways of Internet connectivity and try as a I might, can't get my head around it.
    This desktop computer runs Vista OS. Vista was **bleep** when it came out and is renowned for its botched handling of Internet connections. So I'm not blaming BT for the literally unending connectivity problems that are occurring now, with line drops, speeds slowing to a crawl, and no guarantee that any connection will last. But it would be good to actually use BT software to help fathom out what's going wrong here, and today's typical morning which looks like this:
    1) Boot up computer. Automatic connection to hub via Netgear USB wireless adapter. Hub is on ground floor of this 3-storey property but signal strength from hub  is excellent, as confirmed by inSSIDer monitoring, currently showing 54 with no other networks anywhere near that figure.
    2) Perhaps 5 minutes after connection established, it's then lost. 'Local Only' is displayed. This is, apparently, a known Vista problem. But Microsoft has issued a fix for it. I know this, because it took 100 hours of ploughin g the Net to find out that MS had finally admitted to one more Vista screw-up. I've used the Microsoft router "fix it" before and it didn't work ("failed to process") so uninstalled it and have DL'd it again now and run it. This time it says it has fixed everything.
    3) Computer is re-booted to make the fix effective. Computer connects to Internet. Speedtest.net check yet again confirms that upload speed is faster than download speed.
    4) Connection dies. So much for Microsoft Fix It.
    5) Windows diagnostics reports that it can re-set the IP profile (or something.) I click yes. The re-set goes through. Connectivity is restored. 10 minutes later, connectivity is lost. Just a red X in the tray. No connection of any kind, not even that daft 'Local Connection' only alert.
    6) Reboot. Yet again. BT Desktop Help was installed here and ran OK when we were using our Netgear DSG34 router. But since the change to the BT Hub, the BT program has never run at all. So-oo. . . It has been uninstalled. And then re-DL'd and re-installed. And though the installation  has been completed, clicking on 'launch' has failed to launch anything. But anyway. An hour ago, in one of the brief periods today when the Internet connection was holding up, I Revo-ed out the earlier install, DL'd BT desktop Help and re-installed it. . . and I'm still at the same stage as always, with a  Firefox browser page that's open and completely blank and has been for the past 30 minutes. The URL is:
    file:///C:/Program%20Files/BT%20Broadband%20Desktop%20Help/btbb/Start.html
     Repeated page re-loading gets nowhere. Malwarebytes PRO is turned OFF to prevent any possibility of blocking and the antivirus is termporaily SUSPENDED. This PC runs on Windows standard firewall but even turning that OFF doesn't get the page to load. Copying the address into Internet Explorer in case there's a Firefox problem merely results in Firefox being opened and the same blank page running there.
    7) After all that. . . Connection lost yet again and this time, Windows cannot connect at all. It reports that the "wireless network security key is not correct". I happen to know that it is, because this is maybe the 20th time it has reported this in the past 10 days and every time I have to key in the "correct" key all over again. . . at which point Windows still says it isn't correct and cannot repair.
    Turning off the computer completely, unplugging from the wall, holding in the power switch for a full minute to clear the circuits, traipsing up and dowen three flights of stairs to turn off the hub, then wait, then turn the power back onm again. . . Ah, wot fun times I'm having here with my particular versioin of Infinity (as in, an infinity of connectivcity problems.)
    Summary: I seem to be being simultaneously hit with one issue after another.
    I'm bewildered as to why ever since Infinity was installed here, my upload speed is generally faster than my download speed. I'm not happy with endless Internet connection failures though am thinking that Vista is playing a large part here with its "wrong security key" and unending 'Local Only / Limited Connection' failures. I do miss my Netgear router and the ability to access a fantastic help menu and re-boot directly from the desktop without having to keep going up and down three flights of sdtairs to do so (I haven't been able to find out how toe access the BT Hub remotely.)
    Above all though: I'm  really tired of repeatedly trying to run freshly downloaded and installed BT Desktop Help software but getting no further than a blank page because the program has stalled.
    If anyone has any advice / suggestions, other than to buy a carrier pigeon, that'd be much appreciated.
    Thanks.

    Thanks again to John and gg30340. Here's an update:
    1) BT Desktop Help removed completely from this computer. The uninstaller itself mopped up everything, which surprised me. But anyway.
    2) Bt Home Hub manager set up and working. Had to input serial number and create new password. All of this sounds fairly easy and would be if one had the device near the desk. But the idiots who built this property shoved the BT master socket inside the garage next to the door. Our two home computers are on the third floor. To ensure the wireless signal strength is OK, the Hub and Infinity module/device/whatever it's called are on a high shelf. It's a major job to even reach the darn things, never mind read the labels seeing as how the BT Infinity engineer was good enough to tidy up the cabling and make a very tight connection to the wall socket.
    3) I had hoped to be able to back up the Hub's settings, seeing as the software provides for Advanced Settings / System / Backup. But not on mine (Hub 3.0). All that System allows is choosing which internet clock to define the accurate time. Everything else in System is just a pattern of short lines as if trying to indicate that there's some text there but it's invisible.This is now my second encounter with BT software which, for whatever reason, isn't functioning as it should on this PC.
    4) Hub reset to factory fresh, according to BT guide.
    5) Reset appears to have achieved nothing apart from requiring the password to be popped in again. After reset, it wasn't even possible to connect to the hub manager. Internet connectivity was eventually established for all of 30 seconds and then, gone.
    6) Computer was shut down and then booted anew. Internet connectivity is still. . . dreadful. One minute everything's fine and then, literally,. the next minute a webpage won't load. Even opening the Hub Manager has taken three attempts, i.e., disconnecting from the Internet, re-connecting, failing, and trying twice more until success. Yet all the time these failures are occurring, the tray icon is showing a steady, unwavering green icon for Local and Internet access -- despite the fact, there manifestly isn't any.
    7) Speedtest. net tests are actually showing upload and download 'trajectories' going slower and slower and finally halting at some point on the arc, then after a period of up to 30 seconds, suddenly becoming animated again. Speed test results with broadband speed checker UK and Think Broadband's checker are so at variance with one another, and with Speedtest, net, that it seems all three are using different technologies in pursuit of the same thing. Either way, upload speeds continue to be much, much faster than download speeds, a state of affairs I certainly have never encountered before.
    8) Speedtest net tests taken in the past 10 minutes, with one test following on from its predecessor, begin at 8.24 down/8.88 up, followed by 5.24 down / 6.40 up, followed by a mind-numbingly lonnnnng 0.62 down / 8.70 up -- in other words, a continuous yo-yoin g of Internet connectivity to the pooint that it actually might as well not even be here (I've had to make five attempts just to get on to this forum. . .)
    9) BT Speedtest will necessitate disconnection of everything downstairs and all boxes being lugged up here. This is actually going to require uncoililng tied-off cabling and hanging off a stepladder to do so -- though I surely can't be the only person in Britain who doesn't have a nice, handy BT master socket in their study or lounge. That said though: until we switched to Infinity, we *never* experienced these kinds of horrendous connectivity problems and never had need to unplug the Netgear router downstairs and bring it upstairs to connect directly to tjhe desktop PC so BT's own test could be run.
    I'll just have to get to work dismantling stuff tomorrow. However, I have to say that after a factory re-set which has changed nothing at all, I'm beginning to think there's a problem with the BT line itself (hence why I'm happy to follow the advice here, though less than happy at the prospect of the messing about involved.)
    Thanks, you two, for your patient help, and also for clarifying the situation re the three signal paths being shown on inSSIDer. At least I know that's usual now! And now, hopefully, when I press 'Post', I won't be faced with an endlessly spinning Firefox circle culminating in  what may well be, or seem to be, the 57,938th time today of seeing "Page Not Found". . .

  • PHP and MySQL Connection problem

    I am trying to make a PHP MySQL on a remote server connection in Dreamwesaver CS3.
    When I enter the information (host, user, password, etc.) and hit TEST, I get the following error message.
    "Access Denied. The file may not exist, or there could be a permission problem. Make sure you have proper authorization on the server and the server is properly configured."
    I know the user, password, etc. work, as I can access the MySQL database with other software.
    I checked with my host and they say there are no permission problems on their end.
    I have checked the settings on the Test Server page in Site Setup and everything looks correct and works there.
    I have not seen this particular problem described in other forum postings (although there are a LOT of postings on this topic!).
    Any help would be appreciated.

    I thought my testing server was the remote server and is always on as far as I know. I don't know how to turn it on or off.
    Is there some other testing server that I should be aware of?
    Frank
    Date: Wed, 3 Jun 2009 15:43:02 -0600
    From: [email protected]
    To: [email protected]
    Subject: PHP and MySQL Connection problem
    I know you are using remote, but is your testing server on? if not turn that on and see if that does it. it just happened to me working on remote server and could not get mysql conn to work, until I turn on my testing (developer server), then I was able to connect to mysql and the tables that I created in phpmyadmin remotly was downloaded.
    >

  • TS1538 my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

    my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414
    If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/ht4097
    You may need to try this More than Once...
    Be sure to Follow ALL the Steps...
    But... if the Device has been Modified... this will Not necessarily work.

  • I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?

    Hi
    I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?
    I have tried reseting the network settings and forgetting my wireless connection and re-connecting to it. I even backed up my phone on itunes and restored it, factory reseted it. Nothing seems to work.
    Also after my upgrade to ios 8.1 my personal hotspot option under cellular data has disappeared.
    Would you please help me out? I would really appreciate it.

    Hi..
    Restart your router then restart the iPhone to test.
    If that doesn't help, try this support article >   iOS: Troubleshooting Wi-Fi networks and connections

  • Network connection problems, please help!

    I have had an iPod Touch (4th generation) for over a year now and it worked fine. Today, something went wrong with my network connection. One moment it says that I'm connected to a network, and a few seconds later it says I'm not connected... Then a few seconds later it's connected again. I have full wifi bars, and it does it throughout my whole house. The wifi symbol keeps going on and off. I tried turning my Verizon Westell Model 6100G Modem off and back on because this normally fixes my wifi connection problems. This didn't work. Then I tried turning my iPod off and back on. This didn't work. I tried turning the wifi off and back on. This didn't work. I tried forgetting my network and signing back in. This didn't work. I also tried resetting the network, and this didn't work either. I'm not having any connection problems with my laptop, it's working fine. It's only my iPod. I'm still able to use the wifi, but for a split second, it will not work. I'm not sure what else to do. It's very annoying! I'm going to see if it does this at other peoples houses with their wifi. Can any one tell me what's wrong and how I should fix it? My only theory is a broken antenna...Please help! Thanks!

    I have two things you could try.
    1. Plug your iPod into the host computer that which the network is based around because sometimes the network has trouble identifying a device if it has been a while since you plugged it into the computer.
    2. Find some way to get your network information (IP address, Subnet Mask, Router, DNS numbers) from another device on the network (e.g. laptop). Then go to Settings > Wi-FI and find your router and tap the blue arrow to the right of the name and tap the tab that says "Static" and enter this information accordingly. Then exit back to the network names menu and re-enter your passcode for your network (assuming you have a passcode)

  • SAP Crystal Reports data source connection problem using sap business one

    Hi,
    I m facing a problem regarding: SAP Crystal Reports data source connection problem using sap business one
    I am trying to create a Crystal report but when I try to configure a new connection it does not work.
    I select Sap Business One data source and try to complete the information required to connection but it does not list my companies databases, what is the problem?
    Our Current SAP related software details are as follows:
    OS: Windows Server 2008
    SAP B1 Version: SAP B1 9 (902001) Patch 9
    SAP Crystal Report Version: 14.0.4.738 RTM
    Database: MS SQL Server 2008 R2
    I have also added some screenshots of the issues.
    Please have a look and let me know if you have any questions or any further clarifications.
    I m eagerly waiting for a quick and positive reply.

    Hi,
    There is problem with SAP Business One date source.
    I had faced same problem, I used OLEDB Data-source, and it worked fine for me.
    So, try to use OLEDB.
    Regards,
    Amrut Sabnis.

  • WiFi Internet connectivity problems after upgrade to 10.8.4

    After upgrading to MacOS 10.8.4 I am facing regular interruptions to my WiFi internet connectivity. Periodically the internet connectivity is lost and the only way to fix the problem is to turn WiFi off and on again. This happens frequently when I am downloading files at using big bandwidth (more than 1.5-2 MB/s). If I use assist me on the Network preferences tab, it displays an ISP error when the connectivity is down, however I am certain that I do nota have any kind of ISP or router issue since at the same time I have WiFi internet connectivity from my iPad mini, iPhone 4S and Samsung Galaxy S3. Therefore it should be a 10.8.4 issue

    Troubleshooting Wi-Fi issues in OS X
    Wireless Connection Problems - Fix
    Wireless Connection Problems - Fix (2)
    Wireless Connection Problems - Fix (3)
    Wireless Connection Problems - Fix (4)

Maybe you are looking for

  • CD/DVD drive issue on Satellite A100

    Hi..I can normally play any type of cd or dvd...the cd or dvd just turns in the computer and it does not open, when i restart the computer and put the cd/dvd in straight after the cd/dvd will play..if i go to play another cd/dvd at a later date, i ha

  • Problem in creating new object in this code below

    private Player owner; private int armies; public Territory(String name, Continent continent) owner = new Player(Territory territory, Player owner); <============ ) is expected I have an error following that code. It said that ")" is expected

  • Incorrect syntax near the keyword 'AND'.

    Hi Friends, I have a requirement from SAP BI to SQL database. When I am triggering data from SAP BI, it is successfully sent to XI. In XI, it is also in success. But when I check in Message monitoring, I faced a error. Message processing failed. Caus

  • Where used listing for Query Variables

    Can someone tell me how to get this list from the metadata repository or from the transport connector? I have read this thread "where used" list for BEx variables but this isn't working for us. Is there some config that is required which we have miss

  • Hi, I have a 13 inch mac book pro

    brought in feb this year I want to install windows on it as it works better for my work requirements can any one tell me how much this will cost and what is needed and if anyone has done it? thanks Marcel