WRT160N wireless routher, wireless signal not strong within apartment

I have had the wrt54g for a while now and just recently it stopped working and I had no choice but to get the wrt160n and with lots of difficulty was able to get that going. The wireless signal, on a wpa2personal is fine when I am close to the box which is in the basement of our apartment but upstairs the signal is never as strong as the older linksys wireless router was.
I am really at a loss and the customer service was absolutely no help. I have tried several devices and same result on all of them, max maybe 4 bars for a few min, moslty 1-2 bars.
What is the issue? What other info do you need? any suggestions?
I am a day from returning the box and moving onto another brand or buying the old school one again if I can find it.
Please let me know anyone, you are my only hope!
Mo

Try to readjust the wireless settings on your Router...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Similar Messages

AirPort Extreme signal not strong enough

I have an AirPort Extreme. The signal is strong everywhere except in the kitchen, 15 meters but one story below...thick walls, concrete. Can I extend it using a simple Fritz Box (AVM Fritz wireless LAN 300E)?

Yes, follow the directions in KB 107454, AirPort Extreme and Express: Using WDS to create a network from multiple base stations.

HT201299 Verizon signal is strong but get error message "Ipad is not connected to the Internet"   Wireless works but my Verizon account does not

Verizon signal is strong but get error message "Ipad is not connected to the Internet"   When I try to use Safari.
Wireless works but my Verizon account does not

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

My ipad has suddenly decided not to connect to the internet. My WiFi signal is strong. My PC is connected ok through the same WiFi signal. I have tried pressing the home and off buttons to get the apple logo but this makes no difference

My ipad2 has suddenly decided not to connect to the internet either through Safari or email. My WiFi signal is strong and all other devices in my house are connecting ok. I have tried pressing the home and off buttons together to get the Apple Logo but this has not changed anything, still cannot connect. "Safari cannot open the page because your ipad is not connected to the internet"

I have done this and no difference
I have just realised what has caused the problem.
Yesterday I fitted an additional Homeplug with built in wireless N adapter ( I alreday have another type fitted from my main router position) The wireless system to my ipad is obviously "confused" . Having now removed the second homeplug and reset my ipad all is now ok

X100e - Wireless is on and not working

Hi guys,
I am completely new to the forums and to thinkpads. I have had my think pad for 2 months. Till yesterday everything was working well, until I decided to update the drivers. After it the wireless stoped working. Problem is exactly the same as:
http://forums.lenovo.com/t5/ThinkPad-Edge/Wireless-apparently-active-but-not-working/m-p/280548
However, the solution does not work for me. All my drivers are up to date. I did reinstall the Realtek driver, access connections and updated bios without any luck. Clicking repair does not solve the problem. The wireless is not shut off in the BIOS. Do you guys have anything in mind?
Additional details:
Connection status:       Not connected
Cause:       Association failed - wireless radio not powered on.
Error code:       016
Recommended action:
Communication with access point could not be established because the wireless radio is off. To power on the radio and attempt to connect, click Repair.
If the problem persists, contact your network administrator and provide the troubleshooting information below.
Adapter Details
Adapter name       11b/g/n Wireless LAN Mini-PCI Express Adapter II
Adapter type       Wireless LAN
Adapter speed       54 Mbps
Driver/Firmware version       2017.2.730.2010/ N/A
Adapter status       Enabled
Connection Status       Not connected
Disable unused cards?       Yes
TCP/IP Settings
DHCP enabled?       Yes
Append parent suffixes of the primary DNS suffix?       Yes
Register connection's DNS suffix in registration?       Yes
Register connection's DNS suffix in DNS registration?       Yes
Enable LMHOSTS Lookup?       No
NetBIOS setting       "Default"
Wireless Settings
Network name (SSID)
Connection type       Unknown
Security encryption       Configured by Windows
System Information
System model       35089JG
BIOS version       6XET41WW (1.25 )
Operating system version       Windows 7
Access connections version       5.72
Access Point scan list
Network name (SSID)              Wireless mode MAC address                   Signal strength Channel
Global Settings
Network
Allow Windows users without administrator privileges to create and apply location profiles       ->No
Allow the wireless LAN radio to be turned off when inactive       -> Yes
Enable autodeletion of unused profiles       -> No
Disable the Peer to Peer community feature       -> Yes
Enable SMS feature       -> Yes
Allow selection of location profiles with Fn+F5 On Screen Display menu       -> Yes
Notifications
Show ThinkVantage Access Connections status icon in task tray       -> No
Show wireless status icon in task tray       -> No
Display the progress indicator window when a profile is being applied       -> Yes
Show Access connections Gauge in task bar       -> Yes
Preferences
Enable sound effects       -> No
Do not show balloon tips from the Access Connections system tray icon       -> Yes
Do not show balloon tips from the Access connections Gauge       -> Yes
Show WiMAX page as default on Main GUI       -> No

Hello,
A couple of things to try:
Toggle the Wi-Fi radio on and off by pressing the Fn+F5 key combination.
Open the Device Manager (filename: DEVMGMT.MSC), remove the wireless adapter, then reboot and let Windows re-detect it.
Let us know the results of the above, and we can proceed from there.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

How to use time capsule for wireless back-up but not internet?

Hello,
I have a tower and recently a laptop at work. The tower is connected to our local network with an ethernet cable and the laptop with wireless. So, the internet connection is fine for both.
I was hoping to use my time capsule to do time machine backups on my laptop. Do you have any advice on how to configure this? I do not want to use the time capsule to extend my Internet, as I believe my work I.T. would prefer to handle all access to their network.
Perhaps there is some documentation about doing this that you could point me to? I have not been able to find it.
Thank you for your help.

Your original question was How to use Time Capsule for wireless back-up but not Internet?
There is no reason for you to connect the tower....or anything else...using Ethernet if your goal remains that same as you stated.
If you are asking if you can backup the Tower using Ethernet, and not wireless, then you can connect the tower to one of the LAN <-> ports on the Time Capsule....not the WAN port.
Yes, it appears to work without plugging into my tower.
Correct, it will work.
I just have to select the network that it created. Of course, I have no access to the Internet while this is happening and it can not auto backup, unless I am on that wireless signal.
As I stated, that is the downside to trying to back up without an Internet connection. You have to establish another network...and backup over that network.
If you are asking if you can stay connected to the work network while also backing up to your non-Internet "private" network, that is not possible.

Wireless router works - Airport not allowing connection

I am unable to connect to the internet wirelessly using Airport. I have not changed any settings on the modem, nor on my MBP, however, I am now unable to connect wirelessly.
Airport, when not connected using the ethernet shows full signal - I then try to open a webpage (using Safari) and the connection drops out immediately/ it will remain connected but Safari will tell me I'm not connected.
I have searched extensively on this, and found some possible resolutions - resetting the SMC; removing, then adding the Airport connection/ the previous network connection; restarting the router/the MBP - I have tried everything and nothing seems to be working.
I do recall having had this problem a while ago and it just sorted itself out after much frustration.
Does anyone have an actual solution to this problem - perhaps Apple have made themselves aware of the problem and come up with an actual diagnosis and subsequent solution....
Help please.....

Erm, what do you mean by 'power cycle'?
I have tried restarting everything, and still getting the same problem.
When I first turn my MBP on it registers a full internet connection wirelessly, but then when I load up Safari it says 'no internet connection available'.
This is tres frustrating.

Wireless-Card doesn't not work with WPA/WPA2 but with WEP [Solved]

Hello I have a MacBook (late 2007) with a wireless-card from Broadcam, the card works with WEP and the classic configuration over rc.conf very well. But I can't get the card running with WPA and the net network-profiles.
Here is the link to the driver - http://www.broadcom.com/support/802.11/linux_sta.php
eth2 = wireless-card
eth1 = firewireanything
eth0 = wired-card
rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
#MODULES=(sky2 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="macbook"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="eth0 192.168.1.220 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(!eth0 !eth1 eth2)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
NETWORKS=(wireless)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network net-profiles netfs alsa crond portmap fam hal)
/etc/network.d/wireless
CONNECTION="wireless"
INTERFACE=eth2
HOSTNAME=macbook
IP="static"
IFOPTS="192.168.1.225 netmask 255.255.255.0 broadcast 192.168.1.255"
GATEWAY=192.168.1.1
DNS1=192.168.1.1
# Wireless Settings (optional)
ESSID=3Com
#KEY=
IWOPTS="mode managed essid $ESSID channel 11"
#WIFI_INTERFACE=wlan0 # use this if you have a special wireless interface
# that is linked to the real $INTERFACE
#WIFI_WAIT=5 # seconds to wait for the wireless card to
# associate before bringing the interface up
USEWPA="yes" # start wpa_supplicant with the profile
WPAOPTS="" # use "" for normal operation or specify additional
# options (eg, "-D ipw")
# see /etc/wpa_supplicant.conf for configuration
Can I set here the WPA/WPA2-Key also? Why here ESSID? Do I need still a configuration in wpa_supplicant.conf?
Thats very confusing and not explained.
WPAOPTS? Do I need to add something like "-D wext"?
/etc/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
network={
key_mgmt=NONE
priority=-9999999
network={
ssid="3Com"
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="topsecret"
priority=5
# WPA2
# proto=WPA RSN
I need help. Please
Last edited by hoschi (2009-01-04 20:21:58)

fwojciec wrote:If this info is not in the wiki it might be worth it to add it -- it's all detailed in /etc/network.d/examples/complete.example though.
Thats the reason why I was so confused.
My new and well working configuration:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
#MODULES=(sky2 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="macbook"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="eth0 192.168.1.220 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(!eth0 !eth1 !eth2)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
NETWORKS=(3com)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network net-profiles netfs alsa crond portmap fam hal)
CONNECTION="wireless"
DESCRIPTION="Very verbose complete wireless example"
INTERFACE=eth2
HOSTNAME=macbook
# Interface Settings (use IP="dhcp" for DHCP)
IP="static"
IFOPTS="192.168.1.225 netmask 255.255.255.0 broadcast 192.168.1.255"
GATEWAY=192.168.1.1
# DNS Settings (optional)
DOMAIN=localdomain
DNS1=192.168.1.1
DNS2=
SEARCH=
# Standard Wireless Settings
ESSID=3Com
SECURITY=wpa-config # One of wep, wpa, wpa-config, none
KEY=""
# Scans to see if network is available before connecting (reccomended)
SCAN="YES"
# Time to wait to connect to a network. Default 15.
TIMEOUT=10
# Pass *custom* options to iwconfig. Usually not needed (optional)
IWOPTS="mode managed essid $ESSID channel 6 key restricted $KEY"
# Any extra arguments for wpa_supplicant
WPA_OPTS=
# For SECURITY='wpa-config' only - filename of a wpa-supplicant config
WPA_CONF=/etc/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
network={
key_mgmt=NONE
priority=-9999999
network={
ssid="Linksys"
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="areulookingatmybreasts"
priority=5
network={
ssid="3Com"
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="nomam"
priority=5
# WPA2
# proto=WPA RSN
There are also profiles for the Linksys-Router and for wired cable.
Thanks for the help!
Last edited by hoschi (2009-01-04 20:21:23)

Wireless network and bluetooth not working on touchsmart 600

This has not worked since day 1 and I have been using wired internet.
I really need to setup a home network and need to use wireless.
Research on the net has led me to belive I should have HP WIRELESS ASSISTANT on my machine... is that correct?
Everytime I try to download it is seem to be for a notepad... mine is a touchsmart desktop...
Please advise

Hi coffee12345,
Welcome to the HP Forums!
I have read your post on your wireless keyboard and mouse not working with your desktop, and I would be happy to help you! To begin, I need to ask you a few introductory questions:
What is the Product and Model Number of your desktop?
What version of Windows are you using?
Is this a recent issue, or has it been like this since day one?
Are you using a USB hub to connect your peripherals or is it directly plugged into the computer?
Please re-post with the necessary information, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

I am using chat-r wireless and facetime is not working but when i put rogers fido or any other carrier sim in it work. Anyone know what the problem?

I am using chat-r wireless and facetime is not working but when i put rogers fido or any other carrier sim in it work. Anyone know what the problem?

I'm guessing it's a compatibility problem similar to that that T-Mobile in the US has. I'm not familiar with chat-r wireless, but I'm guessing it's not a supported carrier for the iPhone. If they can't tell you how to fix it, I'm guessing it's just plain not going to work.

I am unable to stream Netflix to my Iphone or Apple TV, from my wireless router . . . even though I am able to watch Netflix on my WII (also wireless) and desktop computer (not wireless).

I am unable to stream Netflix to my Iphone or Apple TV, from my wireless router . . . even though I am able to watch Netflix on my WII (also wireless) and desktop computer (not wireless).
On the Iphone and Apple TV I can connect to Netflix . . . it recognizes me and my account settings . . . and I can veiw all my recent programs and show titles, descriptions, etc.. But when I select one to watch I get a message saying:
"ERROR A PROBLEM OCCURED WHILE PLAYING THIS ITEM. TRY AGAIN LATER, OR SELECT A DIFFERENT ITEM. GO TO WWW.NETFLIX.COM/SUPPORT FOR MORE INFORMATION. (139)
Netflix support say there is nothing wrong on their end . . . that it is an Apple issue. They see the request for the show, the devices are registered . . . but it shows 0 bandwidth to the device.
My Apple TV did this when I first hooked it up a couple of weeks ago. Then after a few days started working with Netflix, for no apparent change . . . now doesn't again for the past couple of days (I think that it auto restarted the other night after a virus scan).
Very frustrating, and driving me nuts! Has anyone else had and been able to resolve this problem?

Troubleshooting
Apple TV2 update one day and netflix is browsing but not launching the actual content (error 139)
Ipad2 (another ios device) forces me to update netflix if I want to use it and I get the same error 139 on it.
**** now I have two not ways not working where prior to some update it was fine.
Nintendo Wii is still working ( mind you running an ancient version of netflix ) Dusted the Wii off and gave it to the kids use. Now they are happy again...
PC is also still working ( using some other flash client ) but that's just of interest, we're not going to be watching tv with that.
My wife's iphone 4s is still working. Odd.. still ios but for somereason I am not forced to update the version. So basically she could mirror stream up to the apple tv with it. Nice feature of Ios5. Later found out it is using 1.4 version of netflix. The most useful thing out of that is that all 3 of the devices are Ios and it was actually the iphone with the 1.4 version of netflix that still worked!
I heard from a friend who was on a different ISP he was still working so I took my appletv2 and ipad2 over to my brothers house who is on that same ISP as my friend and both started working. So the ISP is involved too!
Brought the appletv2 and ipad2 back to my house hoping it would maybe still work. No dice Broken again.
Searched the appstore for a decent packet analyzer and there isn't really anything. I was able to sniff the traffic with my PC and also on my juniper ssg5 confirmed that. Turns out port 80 traffic is actually failing and authorization is not happening. The other clients do not do this...
Asked a buddy from work who used to work at the ISP if he could make a call to some one who might actually know what is going on. He came back pretty quick and said yea they are trying really hard to get the beta patch in from Bluecoat asap.
So knowing that it was actually Netflix that changed when it hit 2.0 and in my case the ISP made the adjustment it's pretty safe to say this issue is going to be ongoing unless netflix changes again the way they authorize for licenses.
So that's the summary of what went right down the troubleshooting path but I'll tell what what didn't
2 calls to Netflix (useless... waste of time... they are too quick to blame anyone but themselves)
1 call to apple support (support call was going to cost more than it cost for me to change ISPs)
2 calls to ISP (through the normal means - regular support number)
So why is this intermittantly working sometimes? If you are lucky enough to authorize to an IP address that is not cached they voila you are going to get an authorization / a license to watch the show. Some people report after defribulating their appletv (reseting, rebooting, dns changes, you name it) they get it working. Over the past month we all seem to have got it working for some period of time only to lose it a day to two later.
It's now been several days since the beta patch to the bluecoat and 4 of us who have been communicating on the issue appear to be online all at the same time for those several days and that is a good sign that we might be out of the woods on the issue.
Hope this turns into something helpful for someone else out there.

I have a internet connection thru a cable modem but the signal is not strong to reach one of other rooms, so i purchased a airport express so how do i connect it to the exisiting modem do i have to install the cd that came with it, the modem is connected

I have a existing internet connection thru a motorola SBG900 cable modem connected to my imac, i purchased a macbook pro but the signal is not strong, so i purchased a airport express but i dont know how to install it, do i have to install the CD on my macbook pro or the imac. i live in a four bed room house distance between the imac and macbook pro is around 25 -30 feet.
Thanks
Yesh

Hello:
This article will give you basic guidance.
http://docs.info.apple.com/article.html?path=Mac/10.7/en/mchlp2875.html
Barry

My wireless hp printer will not communicate with my hp pc

my wireless hp printer will not communicate with my pc

Please read this post then provide some details. What printer model? What operating system? How is the printer connected - Wireless LAN or bluetooth?
Running the diagnostics at http://www/hp.com/go/tools may help resolve the issue.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

I am a windows user that has converted to Mac and loving it but when I updated to Lion my wireless internet dongle would not work anymore and the Macbook Pro does not recognise the device at all so I am unable to reinstall it again. Any ideas

I am a windows user that has converted to Mac and loving it but when I updated to Lion my wireless internet dongle would not work anymore and the Macbook Pro does not recognise the device at all so I am unable to reinstall it again. Any ideas would be greatly appreciated.

Go to Finder > Preferences then select the General tab
Make sure External disks is selected.

I just purchased an Apple TV. I have a pc running windows 7. It is connected to a router and the router is connected to a wireless router. I connect my iPhone, iPad and apple tv to wireless network but do not know how to put the pc on the wifi network

I just purchased an Apple TV. I have a pc running windows 7. It is connected to a router and the router is connected to a wireless router. I connect my iPhone, iPad and apple tv to wireless network but do not know how to put the pc on the wifi network so the Apple TV can do home share.

I don't mean to be facetious but sometimes the simplest things are overlooked. To connect to your library you have to have the computer where the iTunes library is located running and with iTunes open. It also needs to be on the same network. My network is dual band and works with either stream but a friend of mine does not. He has to set the computer and the Apple TV to the same band. Hope this helps.

WRT160N wireless routher, wireless signal not strong within apartment

Similar Messages

Maybe you are looking for