WRT160Nv2 - Basic setup page not usable

Hello,
I've been using a WRT160Nv2 for almost 1 year now and it works fine.
Since today, I can't access to the configuration page under (192.168.1.1). Actually the page is displayed, but the menu and all the labels are missing. So I can't do any configuration. Firmware version seems to be v2.0.02 (appears on the top-right of the basic setup page).
I already reconfigured the router with the installation setup. Didn't help.
I tried to updated the firmware with tftp.exe but get an error 'Server could not be accessed' and the i have to restart the computer to see the router again.
Can anyone help ?
Regards,
CHReg

Hard reset the router by pressing the reset button for 30 seconds and release.  Wait 30 seconds and power cycle the router.  Now connect via wired computer to 198.162.1.1 username blank password admin and reconfigure the router from scratch.

Similar Messages

  • I have the WRT300N.  When I go to the basic setup page an...

    I have the WRT300N.  When I go to the basic setup page and click on DHCP, none of the devices connected to the router show up.  When I first set up the router they did.  Does anyone know why I can't see them anymore?

    Click refersh & see if all devices are there or not ...
    Also you can check if all computers or devices areturned on or not ....

  • Linksys WRT54G V8 Basic Setup page problems

    I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed."  I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it. 
    Any help would be greatly appreciated.

    Tatonka,
    I assume you downloaded the WRT54G setup software disk into your PC initially. Reset the router (hold in the reset button for 30 seconds), hard wire your PC to the router, and access the Linksys icon on your desktop. Just follow the prompts after that. I had to do exactly this at my daughter's home last evening. Bob

  • IExpenses Setup: Page not found

    Hi friends,
    Apps R12
    Entering on iExpenses Superuser --> iExpenses Setup screen: Policy Tab.Schedules
    Inside Accomodation (i.e.) choosing one of them you have saved... then click on Update General icon.
    It appears a 1st screen of three steps. (General Information, Business Rules and Periods and Rates)
    Clicking on "About this page" or even clicking on Next button.. It appears a blank page with message: Page Not found
    xml file for Page exists on Server.. and all seems to be OK.. but.. I think .. that something in relation with Policies definition-Business Rules could be change... But.. How is possible to give a "No page found" error?
    Page for Accomodation are OIE_POL_ACC_HEADER_PAGE and OIE_POL_ACC_RULES_PAGE , for meals are: OIE_POL_MEALS_HEADER_PAGE and OIE_POL_MEALS_RULES_PAGE
    If it would be in relation with OAF extensions or similar.. (there are not extensions made in policies module for oie) .. I suppose It would be returned those "kindly" Java errors.. but.. even no one of these...
    Ideas?
    I've just checked for the other Policies-Schedules and it occurs the same error while clicking the Next button,.. to all (Car Rental, Meal, .... )and also when I try to create a new one... (clicking on Continue button), except for PerDiem ... ¿?¿?¿?¿?
    :-S
    Thanks,
    Jose

    Hi,
    Please check the log file to find more information about this issue. The path of the log file is:
    C:\Program Files\Common Files\microsoft shared\Web Server Extensions\15\LOGS.
    In addition, please make sure the URL of the site is correct.
    Please check whether you could access other pages in the problematic site.
    Best Regards,
    Wendy
    Wendy Li
    TechNet Community Support

  • NAC - wanna test the basic setup - does not work !!!!

    SCENARIO :
    ·         I have simple NAC setup with 1 NAC MGR “CAM” and 1 NAC SRVR “CAS”
    ·         My users are running network 192.168.10.x/24 , and I wanna implement in L2 VG mode. Both NAC MGR and NAC SRVR can ping each other.
    ·         CAM VLAN 55 = 192.168.55.x/24 , and CAS VLAN 66 = 192.168.66.x/24
    ·         NAC MGR “CAM”  has only 1 cable going to the core switch and NAC SRVR has 2 cables going to the core switch ( one is trusted trunk end and another is untrusted trunk end) . Created two VLANS 999 and 998 and put each of them on each link as blackhole prevention mechanism described in Cisco docs.
    ·         I have a Windows 2008 DHCP Server who is giving the pool of IPs for users from 192.168.10.x/24 and it is working fine. Routing in the core switch is also ok.
    ·         I have SSH and web access to both CAM and CAS boxes.  They are also updating online smoothly.
    ·         From the GUI, I have created the AV Rules also and CAM shows CAS as connected as well !!!!  My version is 4.1.8  (upgraded from 4.1.3 )
    INT VLAN 10 (USER VLAN)  SVI is on core switch = 192.168.10.254 /24
    INT VLAN 55 ( MGMT ) SVI is on core switch = 192.168.55.254/24
    INT VLAN 66 (MGMT) SVI is on core switch = 192.168.66.254/24
    PROBLEM :-
    1.       I am not able to download or get the NAC Client software MSI or stub file or ActiveX prompt to download ….
    2.       I don’t know how to start troubleshooting at this stage. Please note that My client PC is windows XP machine and the port is already configured to VLAN 100.
    I have 1 CORE switch only and my NAC boxes and client are connected to the same CORE switch.

    VLANS Mapping is done in CAM, i didnt find any field in CAS...
    Also, i am copying the switch port configs...  ( a simple logical connectivity diagram was attached also to this discussion already )
    VLANS DATABASE
    ==============
    vlan 10
    name AuthVLAN
    vlan 11
    name TEST_VLAN_USER
    vlan 55
    name NAM_mgmt
    vlan 998
    name DummyVLAN998
    vlan 999
    name DummyVLAN999
    *** Only SVI is VLAN 10 with network = 192.168.11.x/24 , there is no SVI for VLAN 11  ***
    Following ports are configured as follows :-
    ============================================
    interface GigabitEthernet2/9
    description ** NAS's untrusted interface **
    switchport
    switchport trunk native vlan 999
    switchport trunk allowed vlan 11
    switchport mode trunk
    no ip address
    interface GigabitEthernet2/10
    description **** NAS Mgmt interface IP 192.168.66.1 *****
    switchport
    switchport trunk native vlan 998
    switchport trunk allowed vlan 10,66
    switchport mode trunk
    no ip address
    interface GigabitEthernet2/11
    description *** Test User Acess Port ***
    switchport
    switchport access vlan 11
    switchport mode access
    no ip address
    interface GigabitEthernet2/12
    description ***** Connected to Eth0 NAM on IP 192.168.55.1 ***
    switchport
    switchport access vlan 55
    switchport mode access
    no ip address
    spanning-tree portfast
    spanning-tree bpduguard enable
    *** FROM THIS core switch I can ping 192.168.66.1 and also 192.168.55.1 with comfort ***
    ** Please note that actual IPs are 192.168.x.y  and not 10.10.x.y respectively

  • Basic Setup Page doesn't display correctly.

    I logged into my WRT54G router today to change some settings around but the page doesn't display any of the writing or links at the top of the page. I've tried reloading the page and resetting the router but neither of these worked.

    Also when I click the "save changes" button nothing happens. When I opened the page in IE it gave me the Error on Page thing and I clicked it to see the errors. I had 52 errors total with the reason Object Expected for each one.

  • Basic Setup Web Page Error

    When I type in the IP address of the router in the address bar, the page comes up with errors and none of the tabs at the top of the page are showing, meaning I can't click on "Wireless". My router and adapter are showing a connection, but it tells me there is no internet connection found. Which is why I need to access the Basic Setup page. I've tried turning off my pop-up blocker, but no use. If someone could help me I would be grateful!

    >reset
    >reconfigure
    >what happened?
    >same thing?
    >upgrade firmware using TFTP file (download this one from FTP website)
    >reset
    >reconfigure
    I do know everything, just not all at once. It's a virtual memory problem.

  • WRT54G2 internet setup is not saved

    Trying to modify internet connection type using the basic setup, but changes are not saved:
    1. On basic setup page - switch from DHCP to L2TP - page refreshes
    2. Fill in L2TP account info and click "Save Changes"
    3. Page waits for refresh, in the meantime the router  reboots
    when router is back online I see the old settings and the new ones are lost
    Please assist

    You need a wired connection between your computer and router.
    Greetings from Northern Ontario, Canada

  • Blank pages on setup pages 192.168.1.1

    I'm using a WRT54G ver 7 Router. Last night after i tried upgrading the firmware the basic setup pages shows up blank when ever i try to acess certain tab.Take the wireless tab for example i click on it the page turns up blank but it shows done at the right hand bottem corner of the window. Pls help.

    After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch.  If you saved a router configuration file, DO NOT use it.  Do this, then try again to view the router's setup pages.  If this does not fix the problem, follow the tips below.
    To view the router's web pages:
    Use Internet Explorer, it usually works.
    JavaScript must be enabled.
    Use a computer that is wired to the router.
    In the non-working computer, temporarily turn off your software firewall.
    If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
    If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
    If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
    A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
    If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
    If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
    Message Edited by toomanydonuts on 10-09-2007 10:23 PM

  • I have an iphone 4 and after updating it to the ios5 software, it will not allow me to activate nor allow me to leave the setup page. i cannot even restore it. does anyone know what to do?

    i have an iphone 4 and after updating it to the ios5 software, it will not allow me to activate nor allow me to leave the setup page. i plugged it into itunes and it is stuck there too... i cannot even restore it. does anyone know what to do?

    I have had this same issue but thankfully fixed it. Follow he steps below:
    Sync your iPhone with you iTunes therefore your info is backed up. Unplug your phone.
    Go to Settings > Reset > Erase All Content and Settings
    Once your phone has reset and come back on answer the question until it asks if you want to back up from itunes Click this then plug your phone in.
    After everything has sync'd back to your phone everything should work fine.
    Hope this helps.

  • What to do when installing itunes to windows vista home basic an message appears saying"there is a problem with this windows installer package.A program run as part of the setup did not finish as expected.Contact your support personnel or package vendor."

    what do i do when trying to install itunes to my windows vista home basic computer and a message appears saying
    "There is a problem with this windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor."
    Need to know because this is driving me nuts now!

    Let's try the following user tip with that one:
    "There is a problem with this Windows Installer package ..." error messages when installing iTunes for Windows

  • Values not saved in "Global Authentication Setup" page

    Hi,
    I searched a bit in this forum but I couldn't find a related topic. So here is my problem.
    We are trying to deploy a small NAC lab environment. We use NAC Appliance v4.1.
    Now the problem is, that I like to set the values for PEAP and EAP-TLS in the "Global Authentication Setup" page. However, every time I press "Submit and restart" all checkboxes for PEAP and EAP-TLS are not checked anymore.
    I use a WebServer certificate from our PKI and I created it as described in various guides.
    If I create a self-signed certificate with ACS it works fine, but this will not be feasible for a larger deployment.
    I hope somebody knows this issue and can help me.
    Thanks,
    Harald

    I could solve my problem. I had to import the CA certificate in "ACS Certification Authority Setup".

  • Can not login to my EA4500 router's web based setup page

    Hello All-I have a EA4500 router. I attempted to login to my router' web based  setup page late last year using my IE11 browser.I received an error message stating that I cannot login with that browser. I need an updated   IE,Google Chrome or Mozilla Firefox to be able to  visit that site. I attempted about 3 more times and received the same error message. I switched to Google Chrome that worked very well up to tonight(3/31/2004). Cisco web page is preventing me from opening my setup page. I believe I should be contacting Customer Support about this problem but none of their support options cover this problem. Thanks in advance.

    IE 11 isn't compatible.  Use Google Chrome if you don't want to uninstall IE 11 and go back to IE 10.
    You can force the local login by disconnecting the cable from the router's internet port and then logging in.
    If the Smart Wifi is giving you trouble and you don't mind reconfiguring your router. Then you could disable Smart Wifi services.
    To disable Smart Wifi Services:
    Reset the router to factory defaults (recessed button for 30 seconds or through the router UI)
    For setup choose "I want to skip Setup and configure my router manually"
    Please remember to Kudo those that help you.
    Linksys
    Communities Technical Support

  • Can I just setup my pages for just one page not the whole document?

    I want to change my page to landscape but just one page not all document how can I do it.
    thank you

    May you take time to search for the keyword 'landscape' in the existing threads ?
    This question was asked and responded many times.
    Yvan KOENIG (VALLAURIS, France) dimanche 20 juin 2010 20:39:31

  • CS4: How to set up landscape orientation doc with dual page setup vertical not horizontal

    I'm an InDesign newbie and am trying to set up document presets for a landscape-oriented document that will have binding at the top and bottom edges of the page, not the default left and right edges.  So when I open up my spread of pages 2 and 3 I want to see page 2 ABOVE page 3 not to the left of it.
    I can't see any way to do this. Am I missing something or is this just not possible in InDesign CS4 (v6.0.6)?

    The closest you can come out of the box is to set up a facing pages document using portrait orientation, then select the spreads in the Pages panel and Rotate Spread View 90 degrees Counter-Clockwise before you begin the layout.
    This will allow you to work "as if" your pages were landscape and bound on the long edges, but things like x and y coordinates will be swapped bcause you are really still working on rotated pages.

Maybe you are looking for

  • How to load the international characters by using the SQL*Loader(UNIX)?

    Hi Everyone, I am not able to load the international characters thru SQL*Loader which is calling from Unix. Whenever I load these characters , appears in DB such as Square box. Please help me how to resolve the issue. Using version is: Oracle Databas

  • Garageband-24 bit?

    What is the bit rate of audio that is recorded onto Garageband? I just got a new Zoom G21U multieffects pedal with a USB connection so that it can be used as an interface with my Mac. The Zoom box has a sampling rate of 96 kHz and 24 bit A/D/A conver

  • Pass parameter to a report link

    HI, This is what I am trying to do: I want to create a report with 2 parameters - FromDate and ToDate. The report link will be something like this - http://xyx.com/report1FromDate=1jan2012&ToDate=31jan2012 What I want is the users to change the date

  • Network killed by Gnome

    Hi, Tried to install Gnome today. Curiosity killed more than one cat, sure. There are no connections for me, in good old KDE - and in Gnome, too. Right now I'm sitting in front of Archbang livecd system, the main arch install properly chrooted. Unfor

  • Disable Default Settings while saving Layout

    Hi, The client has a requirement wherein he wants to disable the "Default Setting" for all the Users and enable only the "User Specific" while saving a Layout in Standard Reports. Guide me as to how i can address this issue. Regards PJ