WRT160Nv3 has resetted to factory defaults himself
Hello, today I got up and discovered that my WRT160Nv3 router has resetted to factory defaults himself, the name of the Wifi network was "linksys" and all configurations were the defaults...
That's normal? This is the first time it happens.
I've never had that happen....and I don't think it's normal. Make sure you're using WPA or WPA2 wireless security and don't use "admin" for your router password. Also make sure your router is not over heating and is well ventilated....at least 2 feet away from other electronic devices.
Search the forum/board as I'm sure other people have had it happen.
Similar Messages
-
My airport extreme (generation 5) was set up using wifi and has worked flawlessly (on macbook pro 2 iphones and window 7 HP pc)until recently. I have reset to factory defaults over and over but still cannot get on the internet. However I can then take my DSL cord and insert it in a different Ethernet port other than the WAN port and I can get internet on my Mac and iphones but only wifi on my husband's PC. I hate to spend another $179 if this is just something I'm doing wrong. Please help
I'm having a bit of trouble confirming that the ZyXEL is a combination modem & wireless-N router. If it is, then you really won't get any advantages of using the 802.11g AirPort.
If the range of your ZyXEL is limited, you may find that doing either or both of the following will help: 1) Move the ZyXEL so that it is higher vs. lower in the room, that is away from any closed areas or placed in a metal cabinet, and 2) Changing radio channels. The latter is especially important in you live in an area where there are a number of competing Wi-Fi.
A good utility to find out, is iStumbler. You would use this to find these other Wi-Fi and find which have the strongest signal value. Those that do, you would also want to note which channel they are operating on, and then, change yours to one that is at least 3-5 channels away. So, for example, if you find strong ones on channels 1 & 6, change yours to 11. -
I have a cp1215 has started to be extra slow have reset to factory defaults and reinstalled driver
I have a cp1215 has started to be extra slow have reset to factory defaults and reinstalled driver on the computer etc....
I think where it is taking the most time is in the deleting from the print queue. I have an HP desktop computer with 3gb ram on windows xp. even if all I am doing is printing a test page with no other programs started it takes for ever to print a page.
any help would be appreciatedHi Mikeryan,
Have you tried turning off bidirectional communication?
Open your printers and faxes folder, right click the icon for your printer, and choose printer properties.
Go to the ports tab, and un-check "Enable Bidirectional Communication".
Restart your computer, and try printing to see if the issue has been resolved.
Hope this helps
I am an HP Employee
Click the KUDOS Star to say "Thanks"
Please mark the post that solves your problem as "Accepted Solution" -
IOS8 is too slow on iPad3! Can I restore to my 7.1.2 backup without having to reset to factory defaults? I have both iCloud and iTunes backups....
No.
Apple has no support or provision for reverting to a previous iOS version.
Try a reset of your iPad by holding down the power button and hone button simultaneously until your iPad screen goes black and the Apple Logo reappears on screen, then let go of the buttons. -
E3000 needs to be restarted regularly, sometimes resets to factory default
My E3000 needs to be restarted at least once a week. Pings to the router will slowly lag over time and reach 700+ after several days from my wired desktop. Sometimes during the restart the router will also reset to factory default settings.
So far I've installed the 1.0.02 (build 4) firmware and done the restart while holding the button. The new firmware has greatly improved my wireless performance but I have no idea what to do next.Follow the below mentioned settings and then check.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter. Leave Username blank & in Password use admin in lower case. Click on the Wireless tab > Click on Advanced Wireless Settings Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings. -
Why WRT610N Automatically Reset to Factory Defaults?
I have been using the WRT610 for few months, this router and others such as NAS, W1Max Modem, Switches power source connecto thru Belkin Power Surge Proctector. This few months I found many times the router automatically reset to factory defaults after power down and up. I have long history with Linksys products and this is the first ever router that automatic reset itself to factory defaults and I can find out why.
For quick power on off I always power down the entire power source at Belkin on/off switch and always wait at least more than 5 seconds, but many times after the power on/off I found cannot connect to the router and all I found are the router reset to factory defaults, any one can explain why and how?I have finally got the time to upgrade the firmware and it turn out to be the same version as my router existing firmware. The reason I did that because the router reset itself to faultry setting again. Wonder anyone has such experience as mine? I roughly recorded it almost once per month the router reset by itself.
-
Satellite L300-20D - Reset to factory default - How?
Hi,
My Laptop is Kind Of Messed Up At The Minute And I Am Looking To Reset To Factory Defaults.
Can Anyone Tell Me How To Do This?
Thanks.Hey,
The exact procedure for HDD recovery is described here:
http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm
But therefore the original OS from Toshiba (Vista) must be installed. If you have installed another OS you have to use the Toshiba recovery disk that you created.
The installation from Toshiba recovery disk you can start if you boot from CD/DVD drive. Then follow the screen instructions to install Windows.
Its very easy because all drivers and tools will be installed automatically.
Please send some feedback if it worked or not. ;) -
How to reset the factory defaults for Adobe Photoshop, CS4. My 'image size' box is not quite right. Thank you.
How to delete/reset Photoshop preferences
Preference file functions, names, locations | Photoshop CS4
To reset within the Image Size dialog press Alt (Option on Mac) and click Reset. -
PAP2T - NA cannot reset to factory default
i bought PAP2T-NA adapter from amazon and I want to upgrade the firmware. I am trying to access the admin page but it keeps asking me for the password. I do not know. I tried entering **** and 73738# also but it keeps saying enter the password and hit # sign.
i cannot reset this device to factory default. can some one help or i am doing something wrong?
I bought from amazon unlocked version.
thank youRe: PAP2T - NA cannot reset to factory default
(Mod note: Removed non-public information. Thank you.)
Message Edited by Vince_02 on 01-29-2010 10:57 AM -
i have a disabled ipod touch. how can i unlock with password without resetting to factory default?
You can rstore from backup but you must restore the iPod
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store -
Cisco IP Phone 7912 reset to factory defaults
Hi to all
Please I ned some advice , I was try to reset to factory defaults a Cisco IP Phone 7912 and I was Ciscfailed .
Please can you help me ?
Thanks a lot !
Hugo BaezHi to all
Please I ned some advice , I was try to reset to factory defaults a Cisco IP Phone 7912 and I was failed .
Please can you help me ?
Thanks a lot !
Hugo Baez -
RVS4000 resets to factory defaults
I just installed a new RVS4000 router (firmware V1.3.0.5), configured it to my LAN, saved the setting and created a configuration backup. 4 times now in less than a week I lost access to the internet only to find the router reset to factory defaults.
I can restore from the backup, but a day or 2 later and it resets again.
Any suggestions - or do you think it's a hardware problem and I should return it for replacement?Please give this a try. First you need to upgrade to the latest firmware version(1.3.2.0). After upgrading to the latest version of the software the next step is to reset the device back to factory defaults. Then after the reset to factory, load the device manually. Next step after loading manually is to save your config file. This should take care of the reset back to factory default issue. If this does not take care of the problem please call into the support center. The number to call is 1-866-606-1866. Also please if you have to call in let the support center engineer know the steps you have already taken.
Thanks
Quendale -
My iphone 4s has hung up while trying to reset to factory defaults.
I tried to reset my iphone 4 s to factory default and it just hangs.ive tried turning off but it just has the line like its trying to update.
Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
until the red slider appears, then slide the slider. Wait for the device to turn off.
* If you cannot turn off the device using the slider, press and hold the
Sleep/Wake and Home buttons at the same time. When the device turns off,
release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
device. The device should turn on. Note: If you see the battery charge warning,
let the device charge for at least ten minutes to ensure that the battery has some
charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information. -
Netgear Wireless Cable Voice Gateway CG3100 periodically resetting to factory default
My CG3100 has run without issue for years but in the last week it has twice, overnight, reset back to factory defaults. The first time I thought it was a glitch. The second time I am thinking hackers. Whichever, has anyone experienced this before? And if so, where you able to implement a fix? My modem spec is: InformationStandard Specification CompliantEuroDOCSIS 3.0Hardware Version1.04AFSoftware Version3.9.21.10.mp2.V0024
Hello,I had one that dropped out intermittently, and had complained 3 times to tech support.Telstra replaced it with a C6300D. The person who changed it said they had several recent issues with others as well. If you're under contract there is no charge.If you're not, have a chat with "Disconnections" in Business Hours, which goes to Adelaide, and they may re-contract you and possibly may be able to negotiate on a modem.
-
LRT214 Router unexpectedly reset to factory defaults.
Last month I replaced my long lived old RVS4000 with the LRT214. I have had my LRT214 for a little over a month and have been running the December firmware update (LRT2x4_v1.0.3.09_20141226) with no problems. Last night, I tried to log on to make some config changes and the router would no longer accept my username/password. Everything appeared to be working fine except that I could not log on to the router. After trying a few different things, I decided to reboot the router. When it came back up, it was back to factory defaults. I tried restoring the mirror config, and that was default as well. I then tried to restore the config from a backup I had done (tried both startup.config and mirror.config) and the router would not accept any password I supplied to read the backup files. Back to square one I decided to reflash, and reconfigure everything from scratch. So far so good.
Has anyone else run into the LRT214 mysteriously resetting everything?
Has anyone tested the backup restore process?
I plan on testing the Backup/Restore myself tonight for sanity in case there is an issue with this version of the software.
Regards,
KarlI haven't had this happen but I only recently installed the new firmware. AFAIK other users aren't reporting this issue.
It's a good IT policy to "Copy Startup to Mirror" once in a while.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support
Maybe you are looking for
-
PO Item Goods receipt indicator change based on PO document type
Hi All, Our requirement is for a particular PO document type the PO Item Delivery tab > goods receipt indicator needs to be set as blank and the field should be greyed. For this PO type we are usign the account assignment category K and F. We cannot
-
Unable to download monthly report sales and trends
Dear all, we are not able to download the "Sales and trends" > Summary sales report > monthly report of last month (February 2014) despite the passage of more than 5 days after the month's end date. The button for the download is still gray instead
-
Adding custom fields to FPE1/2/3 transaction screen
Hi guys, I need to add custom fields from table DFKKOP to transactions FPE1/2/3 under ADDITIONAL DATA area while manually entering NEW BUSINESS PARTNER ITEM. The transaction is not BDT enabled and does not have a screen exit. The user exit and BaDI d
-
My phone does not open anymore, after the battery has been empty.
My phone?s battery turned off, it was empty. I plugged it and it never came back to life It's been 72 hours though... What could I do??
-
I am trying to create an html file for access by a client computer through the LabVIEW Web Server. I want to enable the client to control the vi, so am chosing "Embedded" for the Viewing Option in the Web Publishing Tool. The small preview screen in