WRT1900AC does not support L2TP connection by L2TP server name
Basically - reiterating on my issue again and the question to Linksys personnel: I’m having WRT1900AC and have the issue connecting to my ISP. My ISP uses internet access authorization by ISP L2PT server name (not IP address). Linksys router configuration allows me to enter only IP address of the L2TP server, not L2TP domain server name. This is huge issue for me as I can figure out of course the IP address of the currently active L2TP ISP server but my ISP can not guarantee that in 10-15 min the server IP will be the same. I badly need the capability to use the L2TP server NAME (not IP address) in the config field of the router setup. Please let me know when this feature will be added to the new firmware for WRT1900AC and when this new firmware is going to ben released ? Thanks!
Hmm. What I know is that, Linksys WRT1900AC allows VPN tunnels using IPSec, L2TP or PPTP protocols to pass-through the router. But you can also set your router's Internet Connection Type to L2TP. Simply click on "Edit" (next to "Type of Internet Connection"). Then choose "L2TP" as your Connection Type from the drop-down menu. Make sure your settings (Server IPv4 address, Username, Password, Connection Mode, MTU) match.
Similar Messages
-
"DBSL does not support extended connect protocol" while configuring SSFS
Hi, I'm trying to configure ssfs on ERP EHP7 on HANA Database system. Doing it with this guide - SSFS Implementation for Oracle Database
But when I'm trying to test connection with r3trans I got following error in the log:
4 ETW000 [ dev trc,00000] read_con_info_ssfs(): DBSL does not support extended connect protocol
4 ETW000 ==> ssfs won't be used 26 0.004936
I already updated DBSL_LIB to the latest version, but it doesn't help.
Here is full log:
4 ETW000 C:\usr\sap\CM1\DVEBMGS04\exe\R3trans.EXE version 6.24 (release 741 - 16.05.14 - 20:14:06).
4 ETW000 unicode enabled version
4 ETW000 ===============================================
4 ETW000
4 ETW000 date&time : 02.06.2014 - 13:49:16
4 ETW000 control file: <no ctrlfile>
4 ETW000 R3trans was called as follows: C:\usr\sap\CM1\DVEBMGS04\exe\R3trans.EXE -d
4 ETW000 trace at level 2 opened for a given file pointer
4 ETW000 [ dev trc,00000] Mon Jun 02 13:49:16 2014 106 0.000106
4 ETW000 [ dev trc,00000] db_con_init called 36 0.000142
4 ETW000 [ dev trc,00000] set_use_ext_con_info(): ssfs will be used to get connect information
4 ETW000 61 0.000203
4 ETW000 [ dev trc,00000] determine_block_commit: no con_hdl found as blocked for con_name = R/3
4 ETW000 26 0.000229
4 ETW000 [ dev trc,00000] create_con (con_name=R/3) 17 0.000246
4 ETW000 [ dev trc,00000] Loading DB library 'dbhdbslib.dll' ... 46 0.000292
4 ETW000 [ dev trc,00000] DlLoadLib success: LoadLibrary("dbhdbslib.dll"), hdl 0, count 1, addr 000007FEED100000
4 ETW000 3840 0.004132
4 ETW000 [ dev trc,00000] using "C:\usr\sap\CM1\DVEBMGS04\exe\dbhdbslib.dll" 21 0.004153
4 ETW000 [ dev trc,00000] Library 'dbhdbslib.dll' loaded 21 0.004174
4 ETW000 [ dev trc,00000] function DbSlExpFuns loaded from library dbhdbslib.dll 42 0.004216
4 ETW000 [ dev trc,00000] Version of 'dbhdbslib.dll' is "741.10", patchlevel (0.22) 81 0.004297
4 ETW000 [ dev trc,00000] function dsql_db_init loaded from library dbhdbslib.dll 25 0.004322
4 ETW000 [ dev trc,00000] function dbdd_exp_funs loaded from library dbhdbslib.dll 41 0.004363
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 47 0.004410
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=-1,command=39,arg_p=0000000000000000) 24 0.004434
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 18 0.004452
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=-1,command=10,arg_p=000000000205F170) 22 0.004474
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 17 0.004491
4 ETW000 [ dev trc,00000] New connection 0 created 17 0.004508
4 ETW000 [ dev trc,00000] 0: name = R/3, con_id = -000000001, state = DISCONNECTED, tx = NO , bc = NO , oc = 000, hc = NO , perm = YES, reco = NO , info = NO , timeout = 000, con_max = 255, con_opt = 255, occ = NO , prog =
4 ETW000 38 0.004546
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=-1,command=10,arg_p=0000000141BAEDB0) 44 0.004590
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 19 0.004609
4 ETW000 [ dev trc,00000] db_con_connect (con_name=R/3) 19 0.004628
4 ETW000 [ dev trc,00000] determine_block_commit: no con_hdl found as blocked for con_name = R/3
4 ETW000 24 0.004652
4 ETW000 [ dev trc,00000] find_con_by_name found the following connection: 17 0.004669
4 ETW000 [ dev trc,00000] 0: name = R/3, con_id = 000000000, state = DISCONNECTED, tx = NO , bc = NO , oc = 000, hc = NO , perm = YES, reco = NO , info = NO , timeout = 000, con_max = 255, con_opt = 255, occ = NO , prog =
4 ETW000 164 0.004833
4 ETW000 [ dev trc,00000] read_con_info_ssfs(): reading connect info for connection R/3 34 0.004867
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=-1,command=74,arg_p=0000000000000000) 24 0.004891
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=15) 19 0.004910
4 ETW000 [ dev trc,00000] read_con_info_ssfs(): DBSL does not support extended connect protocol
4 ETW000 ==> ssfs won't be used 26 0.004936
4 ETW000 [ dev trc,00000] { DbSlHDBConnect(con_info_p=0000000000000000) 31 0.004967
4 ETW000 [ dev trc,00000] DBHDBSLIB : version 741.10, patch 0.022 (Make PL 0.26) 34 0.005001
4 ETW000 [ dev trc,00000] HDB shared library (dbhdbslib) patchlevels (last 10) 32 0.005033
4 ETW000 [ dev trc,00000] (0.022) Get database version via dbsl call (note 1976918) 24 0.005057
4 ETW000 [ dev trc,00000] (0.020) FDA: Core Dump in SELECT ... FOR ALL ENTRIES for tables with strings (note 1970276)
4 ETW000 32 0.005089
4 ETW000 [ dev trc,00000] (0.020) SQL DDL with data aging (note 1897636) 21 0.005110
4 ETW000 [ dev trc,00000] (0.017) Datatype NCLOB missing in tablesize calculation (note 1952609)
4 ETW000 30 0.005140
4 ETW000 [ dev trc,00000] (0.014) Tablesize calculation for HANA optimized (note 1952609) 25 0.005165
4 ETW000 [ dev trc,00000] (0.014) Native SQL UPSERT with DataAging (note 1897636) 21 0.005186
4 ETW000 [ dev trc,00000] (0.014) DBSL supports HANA revision number up to 3 digits (note 1952701)
4 ETW000 27 0.005213
4 ETW000 [ dev trc,00000] (0.010) Quotes missing by FAE with the hint dbsl_equi_join (note 1939234)
4 ETW000 28 0.005241
4 ETW000 [ dev trc,00000] (0.007) Obsere deactivate aging flag (note 1897636) 24 0.005265
4 ETW000 [ dev trc,00000] (0.007) Calculated record length for INSERT corrected (note 1897636)
4 ETW000 27 0.005292
4 ETW000 [ dev trc,00000] 15 0.005307
4 ETW000 [ dev trc,00000] -> init() 21 0.005328
4 ETW000 [ dev trc,00000] STATEMENT_CACHE_SIZE = 1000 181 0.005509
4 ETW000 [ dev trc,00000] -> init() 505 0.006014
4 ETW000 [ dev trc,00000] -> loadClientRuntime() 27 0.006041
4 ETW000 [ dev trc,00000] Loading SQLDBC client runtime ... 19 0.006060
4 ETW000 [ dev trc,00000] SQLDBC Module : C:\usr\sap\CM1\hdbclient\libSQLDBCHDB.dll 779 0.006839
4 ETW000 [ dev trc,00000] SQLDBC Runtime : libSQLDBCHDB 1.00.68 Build 0384084-1510 74 0.006913
4 ETW000 [ dev trc,00000] SQLDBC client runtime is 1.00.68.0384084 45 0.006958
4 ETW000 [ dev trc,00000] -> getNewConnection() 28 0.006986
4 ETW000 [ dev trc,00000] <- getNewConnection(con_hdl=0) 78 0.007064
4 ETW000 [ dev trc,00000] -> checkEnvironment(con_hdl=0) 34 0.007098
4 ETW000 [ dev trc,00000] -> connect(con_info_p=0000000000000000) 27 0.007125
4 ETW000 [ dev trc,00000] Try to connect via secure store (DEFAULT) on connection 0 ... 62 0.007187
4 ETW000 [ dev trc,00000] -> check_db_params(con_hdl=0) 61365 0.068552
4 ETW000 [ dev trc,00000] Attach to HDB : 1.00.68.384084 (NewDB100_REL) 7595 0.076147
4 ETW000 [ dev trc,00000] Database release is HDB 1.00.68.384084 49 0.076196
4 ETW000 [ dev trc,00000] INFO : Database 'HDB/00' instance is running on 'hanaserver' 6867 0.083063
4 ETW000 [ dev trc,00000] INFO : Connect to DB as 'SAPCM1', connection_id=201064 43659 0.126722
4 ETW000 [ dev trc,00000] DB max. input host variables : 32767 6954 0.133676
4 ETW000 [ dev trc,00000] DB max. statement length : 1048576 34 0.133710
4 ETW000 [ dev trc,00000] DB max. array size : 100000 75 0.133785
4 ETW000 [ dev trc,00000] use decimal precision as length 21 0.133806
4 ETW000 [ dev trc,00000] ABAPVARCHARMODE is used 19 0.133825
4 ETW000 [ dev trc,00000] INFO : DBSL buffer size = 1048576 20 0.133845
4 ETW000 [ dev trc,00000] Command info enabled 19 0.133864
4 ETW000 [ dev trc,00000] Now I'm connected to HDB 18 0.133882
4 ETW000 [ dev trc,00000] 00: hanaserver-HDB/00, since=20140602134916, ABAP= <unknown> (0) 30 0.133912
4 ETW000 [ dev trc,00000] } DbSlHDBConnect(rc=0) 18 0.133930
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=30,arg_p=0000000000000000) 24 0.133954
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 18 0.133972
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=21,arg_p=000000000205F460) 22 0.133994
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 18 0.134012
4 ETW000 [ dev trc,00000] Connection 0 opened (DBSL handle 0) 36 0.134048
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=7,arg_p=000000000205F4B0) 25 0.134073
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 17 0.134090
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=63,arg_p=000000000205F2B0) 23 0.134113
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 18 0.134131
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=21,arg_p=000000000205F300) 12214 0.146345
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 32 0.146377
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=11,arg_p=000000000205F420) 26 0.146403
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 18 0.146421
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=22,arg_p=000000000205F390) 23 0.146444
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 37 0.146481
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=13,arg_p=000000000205F260) 29 0.146510
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 18 0.146528
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=24,arg_p=000000000205F210) 37 0.146565
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 35 0.146600
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=51,arg_p=000000000205F200) 40 0.146640
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=15) 31 0.146671
4 ETW000 [ dev trc,00000] { DbSlHDBPrepare(con_hdl=0,ss_p=000000000205F4E0,op=3,da_p=000000000205F540)
4 ETW000 46 0.146717
4 ETW000 [ dev trc,00000] -> buildSQLStmt(stmt_p=000000000205F4B0,da_p=000000000205F540,for_explain=0,lock=0,op=3)
4 ETW000 89 0.146806
4 ETW000 [ dev trc,00000] <- buildSQLStmt(len=27,op=3,#marker=0,#lob=0) 33 0.146839
4 ETW000 [ dev trc,00000] -> stmt_prepare(sc_hdl=0000000003AEAC40,ss_p=000000000205F4E0) 75 0.146914
4 ETW000 [ dev trc,00000] sc_p=0000000003AEAC40,no=0,idc_p=0000000000000000,con=0,act=0,slen=27,smax=256,#vars=0,stmt=000000000AD913E0,table=SVERS
4 ETW000 46 0.146960
4 ETW000 [ dev trc,00000] SELECT VERSION FROM SVERS ; 23 0.146983
4 ETW000 [ dev trc,00000] CURSOR C_0000 PREPARE on connection 0 21 0.147004
4 ETW000 [ dev trc,00000] } DbSlHDBPrepare(rc=0) 6174 0.153178
4 ETW000 [ dev trc,00000] { DbSlHDBRead(con_hdl=0,ss_p=000000000205F4E0,da_p=000000000205F540)
4 ETW000 53 0.153231
4 ETW000 [ dev trc,00000] ABAP USER is not set 25 0.153256
4 ETW000 [ dev trc,00000] -> activate_stmt(sc_hdl=0000000003AEAC40,da_p=000000000205F540) 25 0.153281
4 ETW000 [ dev trc,00000] -> bind_variables(sc_hdl=0000000003AEAC40,in_out=0,bulk=0,da_p=000000000205F540)
4 ETW000 30 0.153311
4 ETW000 [ dev trc,00000] -> allocParameter(in_out=0,col_cnt=0) 21 0.153332
4 ETW000 [ dev trc,00000] -> calculate_record_length(sc_hdl=0000000003AEAC40,in_out=0,bulk=0,types=0000000000000000,#col=0,useBulkInsertWithLobs=0)
4 ETW000 54 0.153386
4 ETW000 [ dev trc,00000] #float=0,#lob=0,itab=0,#short=0,#int=0,#llong=0,#uc=0,rec_lng=0,db_lng=0
4 ETW000 33 0.153419
4 ETW000 [ dev trc,00000] <- calculate_record_length(row_size=0, lob_cnt=0, lob_pw_cnt=0, long_cnt=0, ins_bulk_lob=0, row_max=1)
4 ETW000 33 0.153452
4 ETW000 [ dev trc,00000] -> exec_modify(sc_hdl=0000000003AEAC40,ss_p=000000000205F4E0,bulk=0,in_out=1,da_p=000000000205F540)
4 ETW000 36 0.153488
4 ETW000 [ dev trc,00000] -> stmt_execute(sc_hdl=0000000003AEAC40,ss_p=000000000205F4E0,in_out=1,da_p=000000000205F540)
4 ETW000 95 0.153583
4 ETW000 [ dev trc,00000] OPEN CURSOR C_0000 on connection 0 28 0.153611
4 ETW000 [ dev trc,00000] CURSOR C_0000 SET InputSize=1 23 0.153634
4 ETW000 [ dev trc,00000] CURSOR C_0000 EXECUTE on connection 0 22 0.153656
4 ETW000 [ dev trc,00000] execute() of C_0000, #rec=0, rcSQL=0, rc=0 6404 0.160060
4 ETW000 [ dev trc,00000] CURSOR C_0000, rc=0,#rec=0,#dbcount=0 36 0.160096
4 ETW000 [ dev trc,00000] -> bind_variables(sc_hdl=0000000003AEAC40,in_out=1,bulk=0,da_p=000000000205F540)
4 ETW000 33 0.160129
4 ETW000 [ dev trc,00000] -> allocParameter(in_out=1,col_cnt=1) 21 0.160150
4 ETW000 [ dev trc,00000] -> calculate_record_length(sc_hdl=0000000003AEAC40,in_out=1,bulk=0,types=000000000205F518,#col=1,useBulkInsertWithLobs=0)
4 ETW000 37 0.160187
4 ETW000 [ dev trc,00000] #float=0,#lob=0,itab=0,#short=0,#int=0,#llong=0,#uc=72,rec_lng=144,db_lng=144
4 ETW000 31 0.160218
4 ETW000 [ dev trc,00000] <- calculate_record_length(row_size=144, lob_cnt=0, lob_pw_cnt=0, long_cnt=0, ins_bulk_lob=0, row_max=1)
4 ETW000 31 0.160249
4 ETW000 [ dev trc,00000] -> allocIndicator(in_out=1,row_cnt=1) 21 0.160270
4 ETW000 [ dev trc,00000] -> allocData(in_out=1,size=1048576) 21 0.160291
4 ETW000 [ dev trc,00000] -> bind_type_and_length(sc_hdl=0000000003AEAC40,in_out=1,bulk=0,arr_size=1,types=000000000205F518,da_p=000000000205F540)
4 ETW000 45 0.160336
4 ETW000 [ dev trc,00000] -> exec_fetch(sc_hdl=0000000003AEAC40,bulk=0,da_p=000000000205F540)
4 ETW000 41 0.160377
4 ETW000 [ dev trc,00000] xcnt=1,row_i=0,row_pcnt=0 20 0.160397
4 ETW000 [ dev trc,00000] -> stmt_fetch(sc_hdl=0000000003AEAC40) 20 0.160417
4 ETW000 [ dev trc,00000] CURSOR C_0000 FETCH (xcnt=1) on connection 0 23 0.160440
4 ETW000 [ dev trc,00000] next() of C_0000, rc=0 27 0.160467
4 ETW000 [ dev trc,00000] fetch() of C_0000, #rec=1, rc=0, rcSQL=0 28 0.160495
4 ETW000 [ dev trc,00000] -> deactivate_stmt(sc_hdl=0000000003AEAC40,da_p=000000000205F540,rc=0)
4 ETW000 91 0.160586
4 ETW000 [ dev trc,00000] -> StmtCacheFree(DBSL:C_0000) 24 0.160610
4 ETW000 [ dev trc,00000] CURSOR C_0000 CLOSE resultset on connection 0 20 0.160630
4 ETW000 [ dev trc,00000] } DbSlHDBRead(rc=0) 34 0.160664
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=43,arg_p=00000001400FAB06) 25 0.160689
4 ETW000 [ dev trc,00000] INFO : SAP RELEASE (DB) = 740 19 0.160708
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 16 0.160724
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=41,arg_p=00000001400FAB98) 49 0.160773
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 19 0.160792
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=14,arg_p=0000000002055888) 22 0.160814
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 18 0.160832
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=50,arg_p=0000000002055880) 22 0.160854
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 26 0.160880
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=52,arg_p=00000000020558F0) 23 0.160903
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 17 0.160920
4 ETW000 [ dev trc,00000] { DbSlHDBControl(con_hdl=0,command=20,arg_p=0000000141FC74F0) 99 0.161019
4 ETW000 [ dev trc,00000] INFO : STMT SIZE = 1048576 21 0.161040
4 ETW000 [ dev trc,00000] INFO : MARKER_CNT = 32767 18 0.161058
4 ETW000 [ dev trc,00000] } DbSlHDBControl(rc=0) 19 0.161077
4 ETW000 [ dev trc,00000] NTAB: SELECT COMPCNT, UNICODELG FROM DDNTT WHERE TABNAME = 'SVERS'...
4 ETW000 38 0.161115
4 ETW000 [ dev trc,00000] { DbSlHDBPrepare(con_hdl=0,ss_p=0000000002055160,op=3,da_p=00000000020551B0)
4 ETW000 31 0.161146
4 ETW000 [ dev trc,00000] -> buildSQLStmt(stmt_p=0000000002055180,da_p=00000000020551B0,for_explain=0,lock=0,op=3)
4 ETW000 32 0.161178
4 ETW000 [ dev trc,00000] <- buildSQLStmt(len=63,op=3,#marker=0,#lob=0) 23 0.161201
4 ETW000 [ dev trc,00000] -> stmt_prepare(sc_hdl=0000000003AEACD8,ss_p=0000000002055160) 38 0.161239
4 ETW000 [ dev trc,00000] sc_p=0000000003AEACD8,no=1,idc_p=0000000000000000,con=0,act=0,slen=63,smax=256,#vars=0,stmt=000000000AE09690,table=DDNTT
4 ETW000 38 0.161277
4 ETW000 [ dev trc,00000] SELECT COMPCNT, UNICODELG FROM "DDNTT" WHERE TABNAME = 'SVERS' ; 21 0.161298
4 ETW000 [ dev trc,00000] CURSOR C_0001 PREPARE on connection 0 19 0.161317
4 ETW000 [ dev trc,00000] } DbSlHDBPrepare(rc=0) 6453 0.167770
4 ETW000 [ dev trc,00000] db_con_test_and_open: 1 open cursors (delta=1) 30 0.167800
4 ETW000 [ dev trc,00000] db_con_check_dirty: 1 open cursors, tx = NO , bc = NO 18 0.167818
4 ETW000 [ dev trc,00000] db_con_check_dirty: db_con_dirty = YES 16 0.167834
4 ETW000 [ dev trc,00000] { DbSlHDBBegRead(con_hdl=0,ss_p=0000000002055160,da_p=00000000020551B0)
4 ETW000 35 0.167869
4 ETW000 [ dev trc,00000] ABAP USER is not set 23 0.167892
4 ETW000 [ dev trc,00000] -> activate_stmt(sc_hdl=0000000003AEACD8,da_p=00000000020551B0) 23 0.167915
4 ETW000 [ dev trc,00000] -> bind_variables(sc_hdl=0000000003AEACD8,in_out=0,bulk=0,da_p=00000000020551B0)
4 ETW000 32 0.167947
4 ETW000 [ dev trc,00000] -> allocParameter(in_out=0,col_cnt=0) 23 0.167970
4 ETW000 [ dev trc,00000] -> calculate_record_length(sc_hdl=0000000003AEACD8,in_out=0,bulk=0,types=0000000000000000,#col=0,useBulkInsertWithLobs=0)
4 ETW000 34 0.168004
4 ETW000 [ dev trc,00000] #float=0,#lob=0,itab=0,#short=0,#int=0,#llong=0,#uc=0,rec_lng=0,db_lng=0
4 ETW000 30 0.168034
4 ETW000 [ dev trc,00000] <- calculate_record_length(row_size=0, lob_cnt=0, lob_pw_cnt=0, long_cnt=0, ins_bulk_lob=0, row_max=1)
4 ETW000 31 0.168065
4 ETW000 [ dev trc,00000] -> exec_modify(sc_hdl=0000000003AEACD8,ss_p=0000000002055160,bulk=0,in_out=1,da_p=00000000020551B0)
4 ETW000 32 0.168097
4 ETW000 [ dev trc,00000] -> stmt_execute(sc_hdl=0000000003AEACD8,ss_p=0000000002055160,in_out=1,da_p=00000000020551B0)
4 ETW000 32 0.168129
4 ETW000 [ dev trc,00000] OPEN CURSOR C_0001 on connection 0 20 0.168149
4 ETW000 [ dev trc,00000] CURSOR C_0001 SET InputSize=1 19 0.168168
4 ETW000 [ dev trc,00000] CURSOR C_0001 EXECUTE on connection 0 20 0.168188
4 ETW000 [ dev trc,00000] execute() of C_0001, #rec=0, rcSQL=0, rc=0 5712 0.173900
4 ETW000 [ dev trc,00000] CURSOR C_0001, rc=0,#rec=0,#dbcount=0 34 0.173934
4 ETW000 [ dev trc,00000] -> bind_variables(sc_hdl=0000000003AEACD8,in_out=1,bulk=1,da_p=00000000020551B0)
4 ETW000 32 0.173966
4 ETW000 [ dev trc,00000] -> allocParameter(in_out=1,col_cnt=2) 21 0.173987
4 ETW000 [ dev trc,00000] -> calculate_record_length(sc_hdl=0000000003AEACD8,in_out=1,bulk=1,types=0000000002055240,#col=2,useBulkInsertWithLobs=0)
4 ETW000 34 0.174021
4 ETW000 [ dev trc,00000] #float=0,#lob=0,itab=0,#short=2,#int=0,#llong=0,#uc=0,rec_lng=16,db_lng=4
4 ETW000 30 0.174051
4 ETW000 [ dev trc,00000] <- calculate_record_length(row_size=16, lob_cnt=0, lob_pw_cnt=0, long_cnt=0, ins_bulk_lob=0, row_max=65536)
4 ETW000 32 0.174083
4 ETW000 [ dev trc,00000] -> allocIndicator(in_out=1,row_cnt=65536) 20 0.174103
4 ETW000 [ dev trc,00000] -> allocData(in_out=1,size=1048576) 30 0.174133
4 ETW000 [ dev trc,00000] -> bind_type_and_length(sc_hdl=0000000003AEACD8,in_out=1,bulk=1,arr_size=65536,types=0000000002055240,da_p=00000000020551B0)
4 ETW000 36 0.174169
4 ETW000 [ dev trc,00000] } DbSlHDBBegRead(rc=0) 24 0.174193
4 ETW000 [ dev trc,00000] { DbSlHDBExeRead(con_hdl=0,ss_p=0000000002055160,da_p=00000000020551B0)
4 ETW000 35 0.174228
4 ETW000 [ dev trc,00000] ABAP USER is not set 20 0.174248
4 ETW000 [ dev trc,00000] -> exec_fetch(sc_hdl=0000000003AEACD8,bulk=0,da_p=00000000020551B0)
4 ETW000 33 0.174281
4 ETW000 [ dev trc,00000] xcnt=1,row_i=0,row_pcnt=0 20 0.174301
4 ETW000 [ dev trc,00000] -> stmt_fetch(sc_hdl=0000000003AEACD8) 20 0.174321
4 ETW000 [ dev trc,00000] CURSOR C_0001 FETCH (xcnt=1) on connection 0 20 0.174341
4 ETW000&Hi,
Could you check for SAP Note 1952701 - DBSL supports new HANA version number
Regards,
Gaurav -
Hi...
I have a big problem in the delivery of mobile and my type is N70 with Computer shows a message saying that some files missing from the mobile and this is the message that appears when connectivity.
PC Suite does not support the connected phone. PC Suite settings file is missing from the phone. Switch off your phone, switch it on, and try again.
Please assist in this matter, I can either send a site that I downloaded through by mobile phone.
thank you very much..
Moderator note: telephone number removed. It is not advised to publish personal contact information on a publically-accessible web forum.
Message Edited by michaels on 14-Feb-2008 08:40 PMHi Guys,
It always better to give more information when you are posting your issues....Please try to give your system info, versions of the pc suite you are facing the issue :-( so that it may help others to narrow down ur issues :-) -
So I'm getting the dreaded "does not support directory connections encrypted with ssl" error when attempting to bind clients (10.5) to the server (10.5).
I followed the Apple KB article, but it did not help...double-checked permissions and the config files.
Binding works fine w/o SSL...but evidently SSL does not.
Any news on this?
Thanks.
jHmmm...still running into the same issue...do I need to give the cert reference text file certain permissions in order to work?
I have followed the advice on afp548, and have a self-rolled CA with a self-assigned cert for the server, which is also the dns name of the server. I copied the CA hash and pointed to that instead of the self-signed cert hash, but still...no dice.
-j -
Hi All,
This is my first post to ms exchange forum am getting Log onto incoming mail server (POP3): Your server does not support the connection encryption type you have specified. Try changing the encryption method. Contact your mail server administrator
or Internet service provider (ISP) for additional assistance. in my outlook clients, till last Sunday (12.04.15) my exchange was well & good, Monday morning suddenly the problem started like none of our outlook pop3 clients are able to communicate
with exchange (rest IMAP, SMTP & Exchange accounts are working fine). i have tried with all port no but no luck. please help me to get raid of this one.
Exchange 2013 CU6 with server 2012 Std 64Bit
Thanks,
MuraliDear All,
I have found the solution for above problem, the problem has occur due to PopProxy inactivity
please find relevant exchange management shell commends below.
1. Get-ServerComponentstate -Identity <yourmailserver.com>
Server Component State
yourmailserver.com ServerWideOffline Active
yourmailserver.com HubTransport Active
yourmailserver.com FrontendTransport Active
yourmailserver.com Monitoring Active
yourmailserver.com RecoveryActionsEnabled Active
yourmailserver.com AutoDiscoverProxy Active
yourmailserver.com ActiveSyncProxy Active
yourmailserver.com EcpProxy Active
yourmailserver.com EwsProxy Active
yourmailserver.com ImapProxy Active
yourmailserver.com OabProxy Active
yourmailserver.com OwaProxy Active
yourmailserver.com PopProxy Inactive
yourmailserver.com PushNotificationsProxy Active
yourmailserver.com RpsProxy Active
yourmailserver.com RwsProxy Active
yourmailserver.com RpcProxy Active
yourmailserver.com UMCallRouter Active
yourmailserver.com XropProxy Active
yourmailserver.com HttpProxyAvailabilityGroup Active
yourmailserver.com ForwardSyncDaemon Active
yourmailserver.com ProvisioningRps Active
yourmailserver.com MapiProxy Active
yourmailserver.com EdgeTransport Active
yourmailserver.com HighAvailability Active
yourmailserver.com SharedCache Active
2. Set-ServerComponentState -Identity <yourmailserver.com> -Component PopProxy -Requester HealthAPI
-State Active
3. Get-ServerComponentstate -Identity <yourmailserver.com>
Server Component State
yourmailserver.com ServerWideOffline Active
yourmailserver.com HubTransport Active
yourmailserver.com FrontendTransport Active
yourmailserver.com Monitoring Active
yourmailserver.com RecoveryActionsEnabled Active
yourmailserver.com AutoDiscoverProxy Active
yourmailserver.com ActiveSyncProxy Active
yourmailserver.com EcpProxy Active
yourmailserver.com EwsProxy Active
yourmailserver.com ImapProxy Active
yourmailserver.com OabProxy Active
yourmailserver.com OwaProxy Active
yourmailserver.com PopProxy Active
yourmailserver.com PushNotificationsProxy Active
yourmailserver.com RpsProxy Active
yourmailserver.com RwsProxy Active
yourmailserver.com RpcProxy Active
yourmailserver.com UMCallRouter Active
yourmailserver.com XropProxy Active
yourmailserver.com HttpProxyAvailabilityGroup Active
yourmailserver.com ForwardSyncDaemon Active
yourmailserver.com ProvisioningRps Active
yourmailserver.com MapiProxy Active
yourmailserver.com EdgeTransport Active
yourmailserver.com HighAvailability Active
yourmailserver.com SharedCache Activ
Replace yourmailserver.com with your server host name.
Thanks -
Am using Outlook calendar for Mac--needed for client connection. Invites will not go out. Error message: "server does not support secure connections." Resolution?
I have done a similar set of things and no results.
This is really odd, Mac Mail works other emasil clients work, just not Outlook.
The only event I can tie it back to is the outage a couple of weeks ago when AppleID's weren't working for a perdion of time. I ended up having to reset mine.
Is it feasible a local certificate got corrupted at the same or, oddly, that the SMTP servers don't have the updated password?
What's odd is that I no matter how much i Google, i can't find anyone else who has this problem, other than here? -
HELP - PC Suite does not support the connected pho...
After trying numerous times now I cannot get my question to you via your website. In utter frustration I am posting my problem here.
My problem is as follows
When I connect my phone via cable to my laptop I get the following error message. 'PC Suite does not support the connected phone. Install a correct version of PC Suite and try again'. I have already uninstalled the version that previously worked fine and downloaded the version recommended by your website which is 6.80.22. This is actually the version I already had which previously did work. I amd still getting the same error message despite uninstalling and reinstalling numerous times. And when I plug my phone into my partners computer it works fine. He has the same operating system and version of PC Suite. I am using Windows XP Home Service Pack. I have a Nokia 6131Thanks for the descriptive posting, unfortunately there are still many things that can be wrong.
You should try the things that are suggested here in many places: go to control panel - add/remove programs and select first Nokia PC Connectivity Solution and run a repair to it by selecting change - repair. Then same thing for Nokia PC Suite, run a repair to it.
Then boot PC.
Then check the PC Suite manage connections icon to make sure that the DKU-2, CA-53 USB connection is activated. -
Fatal error: Client does not support authentication protocol
requested by server; consider upgrading MySQL client in
/homepages/28/d74942468/htdocs/cosmic/sites/onlinemove/Connections/db.php
on line 9
This is the error that comes up on the server where the site
sits. The database is working on my local machine with the local
settings, but wont connect due to the above.
I think im using MySQL client 3.23 How do i upgrade?
I found this on MySQL site:
http://dev.mysql.com/doc/refman/5.0/en/old-client.html
I'm not sure how to edit the connection string to make it
accept the vaules.The_FedEx_Guy wrote:
> Fatal error: Client does not support authentication
protocol requested by
> server; consider upgrading MySQL client in
>
/homepages/28/d74942468/htdocs/cosmic/sites/onlinemove/Connections/db.php
on
> line 9
> I think im using MySQL client 3.23 How do i upgrade?
The MySQL client that the error refers to isn't the version
of MySQL,
but the MySQL library bundled with PHP. It sounds as though
your hosting
company has upgraded to MySQL 4.1 or higher, but is still
using PHP 4.
> I'm not sure how to edit the connection string to make
it accept the vaules.
You can't. It's the way that the user account passwords are
stored in
MySQL. You need to get the hosting company to upgrade to PHP
5 or to
reset the passwords in MySQL using the OLD_PASSWORD()
function. This
needs to be done by someone with top-level administrative
privileges on
the database.
David Powers, Adobe Community Expert
Author, "Foundation PHP for Dreamweaver 8" (friends of ED)
Author, "PHP Solutions" (friends of ED)
http://foundationphp.com/ -
"Exchange organisation does not support this version of Exchange server"
I am facing the error "Exchange Organisation does not support this version of exchange server" at time of installation of exchange server 2007 in the Windows server 2008 Enterprise edition.
I have already installed exchange Server 2010 in the that domain.
The following the image that show the error that i am facing
I have the checked current Active Directory or Exchange Server schema version by using
Using that i got the following information
"dsquery * cn=schema,cn=configuration,dc=india,dc=local -scope base -attr objectVersion"
objectVersion = Windows Server 2008 RTM
CN=ms-Exch-Schema-Version-Pt,cn=schema,cn=configuration,dc=india,dc=local -scope base -attr rangeUpper"
rangeUpper = 14726 ( Exchange server 2010 sp1)
I am attaching the Exchange server setup logs here
[5/31/2013 3:04:28 PM] [0] **********************************************
[5/31/2013 3:04:28 PM] [0] Starting Microsoft Exchange 2007 Setup
[5/31/2013 3:04:28 PM] [0] **********************************************
[5/31/2013 3:04:28 PM] [0] Operating System version: Microsoft Windows NT 6.1.7600.0.
[5/31/2013 3:04:28 PM] [0] Setup version: 8.1.240.6.
[5/31/2013 3:04:28 PM] [0] Logged on user: INDIA\administrator.
[5/31/2013 3:04:28 PM] [0] Command Line Parameter Name='mode', Value='Install'.
[5/31/2013 3:04:28 PM] [0] Command Line Parameter Name='sourcedir', Value='C:\Exchange2007'.
[5/31/2013 3:04:28 PM] [0] Command Line Parameter Name='fromsetup', Value=''.
[5/31/2013 3:04:28 PM] [0] ExSetupUI was started with the following command: '-mode:install -sourcedir:C:\Exchange2007 /FromSetup'.
[5/31/2013 3:04:29 PM] [0] Setup is choosing the domain controller to use
[5/31/2013 3:04:29 PM] [0] Setup is choosing a local domain controller...
[5/31/2013 3:04:31 PM] [0] Setup has chosen the local domain controller NewDelhi.india.local for initial queries
[5/31/2013 3:04:31 PM] [0] PrepareAD has either not been run or has not replicated to the domain controller used by Setup. Setup will attempt to use the Schema Master domain controller NewDelhi.india.local
[5/31/2013 3:04:31 PM] [0] The schema master domain controller is available
[5/31/2013 3:04:31 PM] [0] The schema master domain controller is in the local domain; setup will use NewDelhi.india.local
[5/31/2013 3:04:31 PM] [0] Setup is choosing a global catalog...
[5/31/2013 3:04:31 PM] [0] Setup has chosen the global catalog server NewDelhi.india.local.
[5/31/2013 3:04:31 PM] [0] Setup will use the domain controller 'NewDelhi.india.local'.
[5/31/2013 3:04:31 PM] [0] Setup will use the global catalog 'NewDelhi.india.local'.
[5/31/2013 3:04:31 PM] [0] Exchange configuration container for the organization is 'CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=india,DC=local'.
[5/31/2013 3:04:31 PM] [0] No Exchange organization container was found for the organization. Message: 'Could not find the Organization Container.'.
[5/31/2013 3:04:31 PM] [0] Setup will search for an Exchange Server object for the local machine with name 'PONDY'.
[5/31/2013 3:04:31 PM] [0] No Exchange Server with identity 'PONDY' was found.
[5/31/2013 3:04:31 PM] [0] The following roles are unpacked:
[5/31/2013 3:04:31 PM] [0] The following roles are installed:
[5/31/2013 3:04:31 PM] [0] The local server does not have any Exchange files installed.
[5/31/2013 3:04:31 PM] [0] Setup will use the path 'C:\Exchange2007' for installing Exchange.
[5/31/2013 3:04:31 PM] [0] The server is cluster type: 'None'.
[5/31/2013 3:04:31 PM] [0] The requested cluster type: 'None'.
[5/31/2013 3:04:31 PM] [0] The installation mode is set to: 'Install'.
[5/31/2013 3:04:31 PM] [0] Exchange organization name is required for this mode.
[5/31/2013 3:04:31 PM] [0] Active Directory Initialization status : 'True'.
[5/31/2013 3:04:31 PM] [0] Schema Update Required Status : 'False'.
[5/31/2013 3:04:31 PM] [0] Organization Configuration Update Required Status : 'True'.
[5/31/2013 3:04:31 PM] [0] Domain Configuration Update Required Status : 'False'.
[5/31/2013 3:04:32 PM] [0] Applying default role selection state
[5/31/2013 3:04:32 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:32 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:32 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:32 PM] [0] InstallModeDataHandler has 4 DataHandlers
[5/31/2013 3:04:32 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:32 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:32 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:32 PM] [0] InstallModeDataHandler has 5 DataHandlers
[5/31/2013 3:04:32 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:32 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:32 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:32 PM] [0] InstallModeDataHandler has 6 DataHandlers
[5/31/2013 3:04:32 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:32 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:32 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:32 PM] [0] InstallModeDataHandler has 6 DataHandlers
[5/31/2013 3:04:32 PM] [0] RootDataHandler has 1 DataHandlers
[5/31/2013 3:04:44 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:44 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:44 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:44 PM] [0] InstallModeDataHandler has 5 DataHandlers
[5/31/2013 3:04:44 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:44 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:44 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:44 PM] [0] InstallModeDataHandler has 4 DataHandlers
[5/31/2013 3:04:44 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:44 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:44 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:44 PM] [0] InstallModeDataHandler has 1 DataHandlers
[5/31/2013 3:04:46 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:46 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:46 PM] [0] Setup will run from path 'C:\Exchange2007\Setup\ServerRoles\Common'.
[5/31/2013 3:04:46 PM] [0] InstallModeDataHandler has 4 DataHandlers
[5/31/2013 3:04:48 PM] [0] Validating options for the 0 requested roles
[5/31/2013 3:04:48 PM] [0] Validating options for the 0 requested roles
[5/31/2013 3:04:53 PM] [0] Setup is determining what organization-level operations to perform.
[5/31/2013 3:04:53 PM] [0] Setup has detected a missing value. Setup is adding the value PrepareOrganization.
[5/31/2013 3:04:53 PM] [0] Because the value was specified, setup is setting the argument OrganizationName to the value First Organization.
[5/31/2013 3:04:53 PM] [0] **************
[5/31/2013 3:04:53 PM] [0] Setup will run the task 'test-setuphealth'
[5/31/2013 3:04:53 PM] [1] Setup launched task 'test-setuphealth -DomainController 'NewDelhi.india.local' -DownloadConfigurationUpdates $true -ExchangeVersion '8.1.240.6' -Roles 'Global' -ScanType
'PrecheckInstall' -SetupRoles 'Global' -PrepareOrganization $true'
[5/31/2013 3:04:53 PM] [1] Beginning processing.
[5/31/2013 3:05:24 PM] [1] [ERROR] The Exchange organization does not support this version of Exchange Server.
[5/31/2013 3:05:24 PM] [1] Ending processing.
[5/31/2013 3:05:24 PM] [0] **************
[5/31/2013 3:05:24 PM] [0] Setup will run the task 'test-setuphealth'
[5/31/2013 3:05:24 PM] [1] Setup launched task 'test-setuphealth -DomainController 'NewDelhi.india.local' -DownloadConfigurationUpdates $false -ExchangeVersion '8.1.240.6' -Roles 'Mailbox' -ScanType 'PrecheckInstall' -SetupRoles 'AdminTools','Mailbox' -CreatePublicDB
$true -TargetDir 'C:\Program Files\Microsoft\Exchange Server' -IISInstalled $true'
[5/31/2013 3:05:24 PM] [1] Beginning processing.
[5/31/2013 3:05:27 PM] [1] [ERROR] The Exchange organization does not support this version of Exchange Server.
[5/31/2013 3:05:27 PM] [1] Ending processing.
[5/31/2013 3:05:40 PM] [0] End of Setup
[5/31/2013 3:05:40 PM] [0] **********************************************
Please suggest me how to install the exchange server 2007 SP1 on the domain that has exchange server 2010 sp1
Thanksdear amit can u tell me I have one doming sg.com .I used for lab first I install in exchange server 2013 is normaly install and working fine .then I format my pc and agine install exchange 2010
Exchange organisation does not support this version of Exchange server
warning
setup is going to perepare the organization for exchange 2010 by using setup/ prepare AD . no exchange 2007 server roles have been deteted in this topology .
please can u tell me the how install exchange 2010
thanks -
Pc Suite does not support the connected phone.Pc s...
My PC version is XP Service Pack 1.I am using PC Suite 6.7.22.I am trying to connect using Infrared.I get the message as mentioned in the subject.Please help. Thanks in Advance
YOu can try to restore factory settings and see if the suite support file reappeares to phone. If not, visit service center and ask th ephone to be PRoperly UPDATED(so that the so called content package is also installed, that contains the Pc Suite support file
-
Weblogic does not support failover for the admin server.
There is a single point of failure in the current weblogic architecture. If the
admin server dies there is no automatic alternate admin server.That is true, and we plan to fix it in one of the next major releases. Currently
the story is not as bad as it appears to be for following reasons:
1. Failure of admin server doesn't mean failure of already running managed server.
2. You can start a new server as admin server of domain with discover flag=true and
it will recognize all already exisiting managed server.
Viresh Garg
Principal Developer Relations Engineer
BEA Systems
naresh gupta wrote:
There is a single point of failure in the current weblogic architecture. If the
admin server dies there is no automatic alternate admin server. -
Error: Device type SWIN does not support page..
Hi All,
I'm working on smartforms which print sticker of size 5 cm width and 2.5 cm hight. I made page of same above mention size. but when i'm trying print this, it will show following error:
Device type SWIN does not support page for ZSTICKER(my page name).
Please do needful help ASAP.
-DharmeshHi,
You need to link your new page to a device type. Use transaction SPAD. Go into the device type and click on the 'Format' button, this will list the supported formats, switch to change mode and add your new page format (ZSTICKER).
Regards,
Nick -
I have a late 2009 MacBook which I want to connect to an old LG tv. The tv does not support HDMI it only has the (red, while, and yellow) ports. Sorry I dunno the exact name for it.
So I was thinking of using the Apple Mini DVI to Video Adapter (s-video), link below...
http://store.apple.com/Catalog/dk/Images/M9319_screen.jpg
But I'm afraid that the MacBook might not support the adapter.
Can anyone give me a solution for this? Is there an alternative way of doing this? I'm kinda new to apple display adapters.The Late 2009 model 6,1 has a Mini DisplayPort not the Mini-DVI. To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info. When the System Profiler comes up check the Model Identifier.
Composite is the name for the red, white and yellow RCA plugs on your TV or red, white and S-Video plugs. If you want to use the Composite input on your TV there’s no Mini DisplayPort to Composite. You’ll have to get a Mini DisplayPort to VGA adapter http://www.amazon.com/s/ref=nb_sb_ss_i_1_19?url=search-alias%3Delectronics&field -keywords=mini+displayport+to+vga&sprefix=mini+Displayport+to and a VGA Adapter to TV S-Video RCA Out Cable for PC Video. http://www.amazon.com/VGA-Adapter-S-Video-Cable-Video/dp/B000Y7T5UU/ref=sr_1_7?s =electronics&ie=UTF8&qid=1316369974&sr=1-7
Only the Yellow plug or the S-Video plug for video will work. For sound you'll also need audio cables to the TV using a 3.5mm stereo headphone jack to RCA sound plugs. You attach it from the headphone jack of your MacBook to the appropriate input plugs on your TV http://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Daps&field-keywords=min i-dvi&x=9&y=13#/ref=nb_sb_ss_i_2_19?url=search-alias%3Daps&field-keywords=macboo k+audio+cable&sprefix=macbook+audio+cable&rh=i%3Aaps%2Ck%3Amacbook+audio+cable -
Hi,
I purchased Huawei Dongle and trying to connect with my new MacBook Pro (OS- Mountain Lion) USB port 3.0 but unfortunately it does not support.
When I plugged in my macbook the power is flowing in dongle due green light blinking twice in every 3 sec but no connection found or diver shown.
Please let me know how I have to use it. I got some suggestion for USB hub 2.0 but It does not make any sense and driver installation.
So please suggest proper direction to use it and provide link to install any driver.
Thanks
Tauheed AhmadYes Clinton I did same, but they were (Huawei customer support) surprised about this problem, They behave like they have no idea about USB 2.0 and 3.0 knowledge. They handsUp that reason I posted my problem in this forum.
So is there any better solution to use any mediator between these USB version handling, Please let me know.
Thanks
Tauheed -
can anyone help when i try to connect my iphone4 to sync with imac g5 i get a message stating my iphone cannot be used as it requires itunes version 10.6.3 or later when ive tried to download this on my imac it says it does not support it.
All i want to do is sync my iphone 4 with my imac g5 can anyone helpClick here and download the software. Unless otherwise noted, a device running iOS 6 requires at least Mac OS X 10.5.8 and iTunes 10.6.3 to be synced from a Mac.
(78390)
Maybe you are looking for
-
My shuffle doesn't connect to pc anymore
hey help my ipod shuffle doesn't connect to the pc anymore...i think there's something wrong with the usb, i want to open it and check better but how can i do it??? help me please
-
When I selected a photo template page, I got 4 slots for pictures. Does that mean I can only, actually, have 4 photos? I can't seem to grab it to duplicate it nor find a place to simply increase the pictures to 6 or 10 or whatever. Should I just skip
-
In winform development,I call the adobe's control named 'Adobe PDF Reader'
In winform development,I call the adobe's control named 'Adobe PDF Reader',when I clicked the button named "mail",the filename was messy code with path in Outlook.
-
Re: Remove BIOS Password Stellite A210-158
Hello. I have a Toshiba Satellite A210-158. I gave him (unintentionally, of course) a BIOS password and do not know how to remove it. I was told to take his lithium battery in him, but I've disarmed and can not find it. Does anyone know how? In advan
-
I've always been worried about moving all my music to a separate drive, but I did it , , and here's my status: My Library in iTunes = 22.39 GB New drive, (H), where I moved the library = 9.47GB When I went to my laptop's hard drive to delete the musi