WRT1900AC - Nest Thermostat disconnects after 30 mins

Just swapped my EA6500 for the new WRT1900AC, and everything is rock solid except for my Nest Thermostat. After about 30 mins the Nest will say that it can't take to the wireless, and if I reselet the SSID again, it will stay connected again for about 30 mins.
I believe this issue has been seen before. Something about routers not supporting low power mode correctly and/or the default for timing about a client is less then 30 mins. The EA6500 never had this issue, but it looks like the WRT1900AC does.
I've even set the 2.4Ghz to WPA2 personal only (as suggested by Nest) and the channel width to 20MHz only, but it's still being disconnected after the Nest enteres low power mode and before it wakes up again 30 minutes later..

When I had the Netgear R7000, my 3M Wifi Thermostat would not connect and hold the link between the router and thermostat. I researched this on the 3M site and it was buried deep in their literature that there unit was having some compatibility problems with certain routers, they didn't name which make or model. According to their article they were soon to release a new FW for the device and an updated app for the iOS. Sure enough, almost 20 days later a new FW and app, and the thermostat was SOLIDLY connected to the R7000 and responding to all commands from the app.
The WRT1900AC connected to ALL of my components right from the get go ..no hiccups. I suspect Nest needs to update their FW and all should be good.

Similar Messages

Why when I use personal hotspot at my iPad mini retina for my iPhone it doesn't stay for long,it disconnect after 5minute

Please...
Why when I use personal hotspot at my iPad mini retina for my iPhone it doesn't stay for long,it disconnect after 5minute

Assuming you are using OSX, connect iphone ny usb then go to system preferences. Go to network pane and scroll down to "wheel" and from the drop down select service order. If you see the iphone then drag it to the top of the list then select apply.

Call is getting disconnect after 3 min when the caller is in queue

Hi,
I am using icm 7.0 with ip ivr 7.0. when all the agents are busy and caller is in queue,call is automatically getting disconnected after 3 min with the message " We are experiancing system problem and unable to process the call. please try again later" .
Icm and ivr script are attached
Regards,
Dinesh Joshi

Hi Chrish,
you are right. the timer was for 180 sec only. now things are working fine after increasing the timer.
Thanks a lot for your reply.
Regards,
Dinesh Joshi

Nest thermostats

Hello. I'm wondering if anyone has ever had any luck getting Nest thermostats to stay connected on a cisco wireless network. We are running 5508s (ver
7.2.110.0) and the thermostats are connecting to a 3502. The WLAN is a locally switched FlexConnect SSID.
According to nest there are two potential issues - NAT timeout and wireless networks that do not play nicely with devices that sleep for long periods of time. I've configured static NAT translations for the Nests, so that shouldn't be an issue. Nest says "Nest uses Wi-Fi 'Power Save Mode' to allow it to sleep and charge its battery while remaining connected to the internet. Not all Wi-Fi routers support this feature or implement it correctly. When they don't, Nest will have difficulty sleeping and will restart in an attempt to reset its network connection. This may happen repeatedly if your Wi-Fi router is incompatible with the 'Power Save Mode' feature." I've tried increasing the DTIM timers to no avail. Does anyone else have any suggestions?
Thanks,
Matt

I did some more reading and the connection problem has to do with the inactivity timeout on the AP.
The thermostat wants to go to sleep for about 30 minutes at a time to conserve the battery built into it.
My AP was set to disconnect unknown clients after 60 seconds. The thermostat would wake up expecting
to already be associated with the AP and the AP had already disassociated it and the thermostat couldn't
handle that. The solution was increase the unknown client timeout to at least 30 minutes and now the thermostat
is staying connected. I actually set my AP unknown client timeout to 10 hours just to be safe.
So far the thermostat is staying connected. I'll post again after a couple of days to see if the fix is permanent.

My VPN keeps disconnecting after downloaded iOS 8. How do I fix this?

my VPN keeps disconnecting after I have downloaded iOS 8 on my iPad. Why is this happening? How can I fix it?

I am having similar issues. IPad mini ios 8.0.2. VPN connection will drop unexpectedly. Actually, it drops coincide with an active application that uses a lot of memory. Such as a web browser. I can 100% replicate behavior by connecting VPN, going to Safari, and opening Facebook. If I don't use an app that is memory-intensive, VPN stays connected indefinitely.

Click ok to disconnect after syncing

This might be a stupid question but I recently restored my mini and after syncing I get the message "Click OK to disconnect" but I don't see any ok button on the computer screen. Does this mean click on the center button on ipod? I tried that and it didn't work. Also now, I can't manipulate the songs on my ipod when it is plugged into my computer. The songs are in a faded text. Help!

Where do you see this message? On the iPod itself?
I've seen "Ok to disconnect" but never with the word "click" in front of it.
The songs are in a faded text.
That means your iPod is set to auto sync with iTunes.
If you have your iPod set to automatically sync with iTunes version 7 or later, connect the iPod and when you see the summary screen, uncheck the box marked "enable disk use".
If you are using an earlier version of iTunes, right click on the iPod in the source list, select options and uncheck the same box.
In future your iPod should automatically disconnect after it’s finished transferring music.

My nest thermostats keep losing connectivity

I have 2 Nest Thermostats. One for the main floor, and a second for the upstairs. Lately one or both seem to not be reachable via my tablet app. I have a Airport extreme for my wifi, and it feed into a Juniper gateway/firewall. I didn't have the problem with the main floor nest, until I installed the 2nd floor nest. I have assigned both thermostats their own static IPs, and they are Mac filtered in both the wifi router, and the firewall. Other wifi devicesIn my home network I have approx 30 devices that are internet enabled. Most are wired via cat6, and the thermostats, apple TV, a tablet and a cell phone are wifi enabled. SO I don't believe it's due to too much WIFI interference, and Previously I've had many more wifi enabled devices on my network, and when the 1st nest was the only themostat, I had no connection problems.

Hi Joan,
I'm sorry to hear you are having issues connecting with Wi-Fi from your iPad.
The article below may be able to help you with this issue.
Click on the link below to see more details and screenshots.
I've quoted some helpful highlights for you:
iOS: Troubleshooting Wi-Fi networks and connections
Be sure that you are in range of your Wi-Fi router (access point).
Tap Settings > Wi-Fi and turn Wi-Fi off and then on again.If unable to do so, see this article.
Confirm that your Wi-Fi router and Cable or DSL modem are connected to power, turned on, and indicate that they are connected to the Internet.If not, refer to your network administrator or ISP for assistance.
Restart your iOS device.
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you are connected. Then tap the blue dot and choose Forget this Network. Try to connect to your desired Wi-Fi network again.
Note: You will need to enter your Wi-Fi password again if your desired network requires one.
Turn your Wi-Fi router off and then on again2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
Update your device to the latest version of software.
Update your Wi-Fi router to the latest firmware2.For AirPort Base Stations, see this article for information about firmware updates.
If your issue is still unresolved
Follow the steps below for the issue you are experiencing.
Unable to locate a Wi-Fi network
Unable to connect to a Wi-Fi network
Wi-Fi disconnects, or signal strength is less than expected
Unable to access the Internet while connected to Wi-Fi
Unable to automatically connect to Wi-Fi
I hope this information helps ....
Have a great day!
- Judy

SQL Developer on Linux hangs when disconnecting after VPN reconnect

Hello,
I have a problem with using connections after general link failure (Cisco VPN disconnect in my case, lost of route to Oracle DB).
When I reconnect to a VPN and I'll try to disconnect from a previously opened (before general link failure) connection, I need
to wait more than 10 minutes to complete this process. SQL Developer is completely unusable during this time.
Steps to reproduce:
1. Connect to VPN
2. Open connection in SQL Developer to host accessible only by this VPN
3. Restart VPN
4. Try to do anything with this connection (disconnect, execute sql in opened SQL Worksheet, view tables, etc.)
This bug is not new in recent versions, I'm using SQL Developer from over 2 years and this bug was always with me. But if I remember correctly in earlier versions (<3.0) I couldn't reuse the connection to execute sql (hanging SQL Developer for more than 10 minutes) but disconnecting would succeed without a problem.
Maybe SQL Developer should move connection management to separate thread to resolve this issue... or is there another solution?
I'm using SQL Developer 3.1.07.42 @ Linux 3.0.4
For VPN connectivity I use vpnc
When I restart VPN connection I'm loosing TUN interface and all routes.
I have tested this issue on a few versions of SQL Developer on Windows XP, including 3.1.07. There is no problem with disconnecting after vpn failure on Windows.
Maybe I should fill some bug report? When I can do such thing? Metalink?
Best regards,
Irek Slonina

Hi Irek,
Possibly you can resolve this issue by altering the type of the connection that becomes non-responsive upon a VPN reconnect. What type are you currently using: Basic, TNS, etc?
In this forum thread (for Windows, unfortunately, not Linux), although different from your case, the solution used Thick/OCI driver, not Thin/Basic:
Windows 7 VPN
I have no VPN client on Linux (much less vpnc), only Cisco AnyConnect on Win XP, so I cannot test your scenario.
Regards,
Gary
SQL Developer Team

I can't be the only one with this issue. MacBook Pro Retina Late-2013 WiFi disconnects after waking up from sleep.

Did anyone buy a MacBook Pro Retina 13" from Best Buy this Black Friday?
I'm having an issue where the WiFi disconnects after the MacBook wakes from sleep but only after a couple of minutes.
Once the WiFi disconnects, I can't reconnect to the same network and sometimes it won't find nearby networks.
I have to turn off the WiFi and wait for at least 5 seconds before turning it back on for it to auto-reconnect to my home network.
If I wait less than 5 seconds, it will continue to attempt connection to the home network but won't connect.
I've tried reformatting and deleting my network configurations as well as resetting my modem, power cycling it, etc.
I am using 2Wire Gateway modem/router from AT&T on b/g network.
I've tried connecting to a friend's network under Time Warner Cable and the same issue occurs.
I exchanged the MacBook at a Best Buy for a brand unopened one (I hope) and the same exact thing happens with this new one.
Really, I can't be the only one with this issue. Unless in a 0.00001% chance I received two defective units in a row?
Please.. does anyone have a clue why this is happening?

You're definitely not the only one. I have the same issue. I spent 6 hours over multiple days on the phone with Apple support trying a variety of things (some of which are mentioned above), and none of them worked. They finally sent me a replacement laptop. I made sure to try it periodicaly as I was moving files and installing applications to see if I ran into it again and things seemed okay at first but now I am running into the same issue and it is terribly annoying. I've got 5 other devices that connect to the same router and I've never had this issue with any of them.
My router is a Linksys E2000. I haven't tried changing the router channel but I have tried to cnnecting to other networks in the building I live in and I have run into the same issue there.

Wifi disconnects after about a minute after i am no longer using my computer . Why is this happening?

After logging into my wifi connection, which does take some time to do.
Why does my wifi disconnect after not using my computer for a few minutes?
I am on osx lion 10.7.5

Computer entering sleep mode after few minutes?

HT1222 I got disconnected after the release of the last update! I'm disconnected only from the app store and itunes. Do i have to update to activate my account? What to do, i'm stuck.

I got disconnected after the release of the last update! I'm disconnected only from the app store and itunes. Do i have to update to activate my account? What to do, i'm stuck.

Have you restarted your phone?
If so, try a reset. Press and hold the home & sleep/wake buttons until the screen goes blank, ignoring the power off slider if it comes up.
Check for the app again after the phone starts back up.
~Lyssa

Skype account keeps disconnecting after 30 seconds

hi guys,
its driving me nuts. my skype account keeps disconnecting after 30 seconds and i haven't even done anything. it does it on windows, and on my iphone too.
what's going on? is this a problem with skype? i've seen similar posts. and i'm using skype 6.20

That generally means there is an issue with your Microsoft account. You may have to verify some settings in your account to make sure a configuration isn't causing it. The only solution I'm aware of is temporarily unlinking your account. I do not know if reconnecting it will resolve the issue right away.
https://support.skype.com/en/faq/FA12211/

Wireless disconnect after login with Remote desktop with wpa2

We have 5508 wireless controller with 1142 aironet acess points.... we configured Radius authentication on ACS 5.3 for wireless users
when we take remote desktop connection of wireless client ... it disconnects after 10 sec.
and when we logged in to client ... connectivity was lossed .. I have to reconnect Manually to client..
It's really frustrating for all our service engineers to work remotly ....... Please Help

Hi Santosh,
which vesrion of sw u r running on WLC ?
Open Caveats on 7.4.100.0, CSCuc78713 could be related to this;
CSCuc78713
Symptom: Wireless client cannot receive broadcast packets after broadcast key rotation.
Conditions: Dynamic WEP; 7.0.235.0, 7.2.110.0, and 7.3.101.0 controller software releases.
Workaround:
• Executes the config advanced eap bcast-key-interval 86400 in the middle of the night
• Change security setting to WPA2, and so on.
Regards

Why does my phone disconnect after 4 hours of call time

why does my phone disconnect after 4 hours of call time? Is there anyway I can change this?

You mean that you're on a single call for 4 hours continously, and then it disconnects?
If so, contact your wireless carrier. That's a cellular connection issue.

Wifi gets disconnected after sometime while watching youtube on iPod Touch.

When I'm watching video on youtube, the wifi network suddenly gets disconnected after some time.
Even when I goto settings->wifi, I'm unable to find the wifi network.
However, at the same time I can find the wifi network and am able to browse internet on my laptop and mobile phone. I get the wifi network back, on when I switch off wifi and switch it after some 2mins of time.

- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router.
- Reset networks settings: Settings>General>Reset>Reset Network Settings
- Does it happen with other networks?
- Next would be to restore the iPod.

WRT1900AC - Nest Thermostat disconnects after 30 mins

Similar Messages

Maybe you are looking for