WRT300N Limited or No Connectivity w/Laptop

Recently my laptop could not connect with my wireless connection, later I found out it was because the WLAN switch was turned off. Now the wireless connection says Limited or no connection. Everything was working fine before that. Also, I do not have a wireless N card, which I know I should probably get, but didn't feel the need to. Any idea what is the problem?
Message Edited by frachinanhan on 12-25-2007 08:10 PM

access the router's ui and check whether there is any wireless security enabled .. if yes, check the security key and use the same to connect to the wireless network..

Similar Messages

  • WRT300N limited or no connectivity

    I searched for this problem and tried the answer given. However, i still have the same problem. It stays on "aquiring network address" for a long time then just switches to the limited or no connectivity. Any ideas? i have a WRT300N and a WMP300N. I can connect to the network just fine, but i just cant connect to the internet. Latest firmware/drivers are being used as well.
    *edit*
    Oh and if i wire directly into the router there is no problems at all. its strictly wireless.Message Edited by Kevo651 on 05-16-200701:38 AM

    what ip address do you get when the computer is directly wired into the router ?? also , what is the internet ip address under the "status" tab on the router's web ui ..

  • Limited or nor connectivity with PC

    Intstalled Time capsule yesterday. Cant get my pc to get internet access with a direct cat 5e wired connection. I get ip address, DNS and Gateway address all look ok, but I cant ping out and the message over the network icons say limited or no connectivity. My hardware information on my network adaptor is set to autosynch and it syncs to Gigabit.
    My iMac via wi-fi is fine. My iPhone is fine, even an old direct wired pc is fine.
    When I plug my old router back into my dsl and wire my pc to it every thing works as it did.

    Recently had a similar problem connecting a friend's PC to my network and thought I would post my fix in order to hopefully help others.
    I noticed that everything worked fine when I disabled wireless security, so my problem was a security issue.
    I re-enabled security on my router and copied down the first actual HEX key (key 1) instead of just using the password. Then, on the laptop with a Netgear wireless card, instead of selecting to type a password, I opted to use a network key and pasted the actual key, and it worked like a charm.
    Maybe it has something to do with aftermarket network cards, but it solved the "network did not assign a network address" problem.
    Hope I've helped and not given a useless answer.
    Adam

  • Limited or no connectivity BS

    I have looked at all the different posts regarding this problem, and I fail to find ANYONE who can actually solve this problem.
    I do not have 2.4Ghz phones that could interfere with the router I have (model BEFW11S4).
    My closest neighbor is about 150 yards away.
    I am nowhere near a radar installation.
    I can connect with this laptop to any other wireless network I have encountered.
    Signal strength is excellent (the router is 6 feet from me)
    I have only 2 wireless devices (laptops), and I have 2 wired devices (printer and WII) connected to it.
    What will it take to resolve this? Switch to someone else's product (apparently Cisco does not care)

    Tutorial was no help. These are all things that I had already tried or ruled out.
    FYI, I am able to connect, sometimes. But tomorrow I could turn on the PC and get a Limited or no connectivity message. I have tried restarting my laptop at that time, which does not help. The only thing that helps is to power cycle the router.

  • Number of connection to this computer limited and all connections are in use right now

    I have Lenovo ThinkPad T520 (i7, NVIDIA 4200TM) with dock station and two monitors. Sometimes when I close notebook and undock it from dock station. Then I cannot login to my notebook because of error "Number of connection to this computer limited and
    all connections are in use right now". This is screenshot of my laptop  http://i.imgur.com/6MXnQKf.jpg
    Laptop is not in domain and does not have remote desktop connections. It was just turned in sleep mode and late turned on. 
    This happen pretty often one from 10..20 times of undock.  It did not happen with Windows 7 before. 

    The network does not work properly after you resume the computer. This kind of issues are cuased by the network device driver. Download the latess Windows 8 driver from Lenovo website and install it.
    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

  • WRT54G - Limited or no connectivity

    I  have a WRT54G that was set up and working great for the past two weeks.
    Last night I had problems connecting via my Laptop and today I cannot connect through my hardwired desktop.  On the desktop I get the message "Limited or no connectivity."
    If I remove the router from the system and wire the desktop directly to the modem I regain Internet Access - so the problem has to be with the router, not the ISP.
    I read some of the other posts and tried to access the router through the #1 port using the default IP of http://192.168.1.1 and using the password of admin.  If I leave the user name blank and input admin as the password I get a screen that indicates that I do not have authorization to enter.....
    Any ideas?  Thanks in advance and have a great Thanksgiving.

    Yes, I used the CD that came with the router. 
    During the installation the CD installed the Linksys Easy Link program. 
    When I tried to use the Easy Link program this morning to fix the problem it didn't seem to recognize the previous settiing and wanted me to start zt the beginning and name the network, etc.  I followed these steps with no success - the end result was a message indicating that the program did not support my router.
    Is it a hardware problem?
    Thanks in advance.

  • Router won't connect to internet, computer shows 'limited or no connectivity' message

    Hi everyone, I could use some help. I have a Linksys WRT150N router that I bought a few years ago. It was working fine till about two days ago. I can't connect to the internet at all through the computer it's connected to or wirelessly on my laptop. The message 'limited or no connectivity' shows up on both computers. I tried resetting and unplugging the router several times, and I can't even access the router's settings using the IP address cause I need internet to do that. I know it's not my modem because when I connect it directly to the computer without the router, I can access the internet. So do I need a new router or is there something else I can do? Could my internet service provider have done something recenly so that it doesn't work with my router anymore? Please help, I seriously don't want to spend money on another router.

    Who is your Internet Service Provider ?
    If you are using cable connection then follow this link and if you are using DSL connection then follow this link.

  • I am trying to connect my laptop to my TV. The computer flashes blue after I plug the cable in but the TV says there is no signal. I have a Mac Book Pro 2009 and a Samsung 32" Class (31.5" Diag.) 450 Series 720p LCD HDTV (2010 model)

    Hello,
    I am trying to connect my laptop to my TV. The computer flashes blue after I plug the cable in but the TV says there is no signal.
    I have a Mac Book Pro 2009 and a Samsung 32" Class (31.5" Diag.) 450 Series 720p LCD HDTV (2010 model).
    I am using a mini display port to VGA adapter. I have sucessfully hooked up boh devices but it stopped working after a handful of times. I was wondering if there is anything I can do to fix the problem or is my cable broken?

    Some things you can try.
    Startup Issues - Resolve
    Startup Issues - Resolve (2)

  • Limited or no connectivity to wireless on XP using Boot Camp

    Hi all, I need a little help!
    I just installed Windows XP with SP2 on my Intel Mac using Boot Camp. Everything seemed fine until I tried to connect to my wireless network. I've installed and reinstalled all of the drivers, and I can see the driver for wireless networking, but every time I connect it tells me it has "limited or no connectivity." Any idea what to do here? Thanks!!

    Denisimo posted this reply to me, and it worked!
    Quote:
    ***Snip
    I found this on one of the Macrumors forums on the web:
    I had exactly the same situation as iBunny.
    I got it working by changing the settings via Airport Utility from "WPA2 Personal" into "WPA/WPA2 Personal" and it worked. Btw, before this, I changed from channel 11 to 1, 1 to 2, 2 to 7 without success. I've kept it under channel 7 and just made the change mentioned above.
    Also, under winXP, I went to Wireless Network Connection properties and filled up the preferred networks. Am not sure if this has anything to do with the problem at hand but I am now connected automatically.
    The user was using a Macbook. Hope this helps.
    Regards Denis
    Message was edited by: Denisimo
    ***Snip
    I just changed from WEP to WPA/WPA2 Personal, and didn’t bother with the rest. That worked.
    Cheers,
    Klaus

  • I have an airport extreme.  i am trying to connect a laptop with windows 7 to a wireless printer, with no luck.  any ideas?

    I have an airport extreme.  i am trying to connect a laptop with windows 7 to a wireless printer, with no luck.  any ideas?

    The problem is not the router.. the issue is the vpn has put your computer in a different IP range with a different gateway. When you turn off the vpn the computer returns to local lan and can print.
    Some vpn software allows you to set gateway to use local net instead of remote gateway or access to other webistes or local lan.
    Read up the issue.
    http://stevejenkins.com/blog/2010/01/using-the-local-default-gateway-with-a-wind ows-vpn-connection/
    Cisco vpn client..
    https://supportforums.cisco.com/thread/239113
    I did not search much.. just grabbed the first article I could find that explains the issue.
    The whole point of the vpn is whilst it is connected your computer is NOT part of the Local Lan .. it is part of the Remote LAN via the vpn tunnel.
    It is also a security risk using split tunnelling so often it will not be allowed.
    Plug the printer directly into the computer via usb or whatever.. Local connection will work.. not local lan.

  • Iphone 3 not charging or connecting to laptop

    Hi, my mate has brought his iphone 3G to me to see if i could assist with problem.
    when the phone is plugged into the mains on charge the apple symbol apperas and is there for some time before anything happens.
    It then dissapears and when you press the home button on the front it says ios 6 and slide bar saying set up.
    The top of the page is saying searching and there is battery symbol.
    upon sliding thebar it requests connect to apple i tunes. upon removal from charger everything instantly goes off and upon connection to laptop via lead nothing ever happens. after a while the apple symbol flashes slowly but this is the end of things.
    the laptop/itunes donot reconise that phone is plugged in.
    Does anyone have any answers for a fix or is the phone finished????
    The phone was working as normal before any problems, he took it into store and they said liquid corrosion which is not right.

    Charge the iPhone to a wall outlet.
    Try a different USB cable.
    Try different USB ports.

  • Just updated KIES and can no longer connect my laptop and S4?

    I've been using KIES for a year.  Was just prompted to update it.  Did so (to version 2.6.0.13091.9) and now I can no longer connect my laptop and Galaxy S4.
    I'm getting the following message which is, of course, nearly worthless:
         Reconnect the device in Samsung Kies (PC Studio) mode.
         Current connection mode not supported by Kies.
         Check the USB settings.
         (Settings -> Applications -> Development -> USB debugging (x))
    1) "PC Studio" has no actual meaning; after searching online I found what they're trying to tell me is the phone must be in MTP mode rather than USB debugging mode.
    2) The Settings path above is wrong; I DID manage to find the proper path to turn off debugging & switch to MTP, but that doesn't help.
    3) uninstalled & reinstalled KIES; no help
    Any ideas? 
    I know 1000's of other people are having this problem, so I'm a bit surprised VZ doesn't have a ready answer here.

        Hey there mjr123,
    I am sorry to hear that you are having issues with the Samsung Kies software.  This is actually a third party application offered through Samsung, so I would recommend reaching out to Samsung's support team for the best assistance.
    NicholasB_VZW
    Follow us on Twitter @VZWSupport

  • I have an Airport Extreme, 2 laptops with windows 7 and a wireless HP printer.  I can connect the laptops to the printer.  Any advise?

    I have an Airport Extreme, 2 laptops with windows 7 and a wireless HP printer.  I am not able to connect the laptops to the printer.  Any advise?

    The problem is not the router.. the issue is the vpn has put your computer in a different IP range with a different gateway. When you turn off the vpn the computer returns to local lan and can print.
    Some vpn software allows you to set gateway to use local net instead of remote gateway or access to other webistes or local lan.
    Read up the issue.
    http://stevejenkins.com/blog/2010/01/using-the-local-default-gateway-with-a-wind ows-vpn-connection/
    Cisco vpn client..
    https://supportforums.cisco.com/thread/239113
    I did not search much.. just grabbed the first article I could find that explains the issue.
    The whole point of the vpn is whilst it is connected your computer is NOT part of the Local Lan .. it is part of the Remote LAN via the vpn tunnel.
    It is also a security risk using split tunnelling so often it will not be allowed.
    Plug the printer directly into the computer via usb or whatever.. Local connection will work.. not local lan.

  • I have a macbook 15 inch and philips LCD which I'm trying to connect my laptop to. I currently have a HDMI plugged in, but am getting an error message "no video input" on the LCD tv. Please help!

    I have a macbook 15 inch (retina display) and philips LCD which I'm trying to connect my laptop to.
    I currently have a HDMI cable plugged in, but am constantly getting an error message "no video input" on the LCD tv.
    I have checked the philips LCD to be in the HDMI mode and googled many threads but have
    not found a solution to solve my problem. Would appreciate any help given!

    Hello, anabelleho. 
    Thank you for visiting Apple Support Communities.
    Here is a troubleshooting article that I would recommend going through when experiencing this issue.
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/ht1573
    Cheers,
    Jason H.

  • After I download a movie onto my laptop,it plays it ,no proplem,but when I connect the laptop to the TV the movie freezes

    After I download a movie onto my laptop,it plays it ,no problem,but when I connect the laptop to the TV the movie freezes?
    Can anyone help please?

    I'm plugging in with  the 15 pin type connector that has finger screws each side of it,(can't remember what it is called) with a separate usual plug into the earphone socket of the laptop and at the other end, into the audio output of the TV. I have been doing this for some time, with Netfix,and  other programs,and never encoutered a problem till I tried Playing a film off I tunes.

Maybe you are looking for