WRT300N Router will not configure during setup
I have a WRT300N Router Version 1.1, when reinstalling this on my computer after a crash I cannot get the setup to complete. When the setup goes throught the config stage it gets to 99% and then stops and gives me an error message that it would not configure.
I have updated the firmware and this still will not get it to work. What can I do?
After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you have not done this since your last firmware upgrade, please do this now and see if it corrects your problem. If you saved a router configuration file, DO NOT use it.
To reset the router press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link
Similar Messages
-
WRT160NL will not configure in setup
Followed QUICK INSTALLATION GUIDE with 3 different computers, and this router cannot be found for set-up. Setup goes OK until powering up router, click "Next" to find it, and........... can't be found.
If your Internet Service Provider is Cable follow this link
If your Internet Service Provider is DSL follow this link -
SQL Server 2012 Developer Edition will not install. Setup files don't even get copied completely. Win 8.1. ACT instance is loaded & can't be deleted. From log file: Error: Action "PreMsiTimingConfigAction" failed during execution.
Hello,
I am glad it worked.
Thank you for visiting MSDN forums!
Regards,
Alberto Morillo
SQLCoffee.com -
C2921 router will not bring up fibre SFP
c2921 router will not bring up fibre SFP
I can't get two cisco 2921 routers to talk to each other
the setup works find in my testbed with a rj45 cross over cable between them or even with a WANEM cloud emulator(free tool).
after migrating from CU to fibre they won't to talk to each other anymore. worse, both refuse to bring up their wan side fibre SFP.
the "media-type" sub i/f command was used to change to SFP from RJ45
after that, the EN SFP light appears on both routers, but no link light
sh int gi 0/1
GigabitEthernet0/1 is down, line protocol is down
Hardware is CN Gigabit Ethernet, address is xxx(bia xxx)
Description: ** TEST LINK
Internet address is 1.1.1.2/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is SX
the two routers are in different buildings and must pass through a middle building(#2)
B1 - 200m -- B2 -- 900m -- b3
R1 (in building 1) is 200m from building 2
R2 (in building 3) is 900M from building 2
R1 has a MM SFP in Gi 0/1
R2 has a SM SFP in Gi 0/1 as the distance is too far for MM
in building two we have used both a SM to MM media converter
and a layer two switch with SM and MM SFP,
both show similar results
R1(MM sfp) --MM cable-- (MM sfp) switch (SM sfp) --SM cable--(SM sfp)R2
on the switch( in Bld 2), we see links lights coming out of the two routers, for both SM and MM links, this is good and expected. no traffic is seen though
on either router, no link light is seen and both interfaces are down down. shut, no shut, does not bring them up
we have tried different SFP and cables, still no change
one google search mentions an undocumented ciso command to ignore incompatibale SFP, but that does not work in IOS 15
if we add a 3750 switch to the routers Gi 0/1 WAN side as a media converter, we get success.
each switch has two sfp, one Cu and the other MM or SM fibre .
the router "media-type" sub i/f command was used to change to RJ45 from SFP, after that, the SFP EN lights goes out(as expected) on both routers,
R1(CU)-(CU)3750(MM sfp) --MMcable-- (MM sfp) switch (SM sfp) --SMcable--(SM sfp)-(SM sfp)3750(CU)R2
why does this work and the connection on the rtr does not
sh int gi 0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is xxx(bia xxx)
Description: ** TEST LINK
Internet address is 1.1.1.2/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is RJ45
this test is not practical in the deployed field and far too expensive
i am looking for a solution and want to know why the SFPs do not work in the routers
i tried two different MM SFP. neither one worked, though from SH INV, one can't tell them apart. on the CISCO site only this one is supported
glc-sx-mm, the SFP-GE-s is not supported on the 29xx rtr but is on the 3750 switch (;
================
%added SFP-GE-s SFP, the SFP-GE-s is not supported on the 29xx rtr but is on the 3750 switch
sh inv
NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V03 , SN: xxxxSFP-GE-s
NAME: "1000BASE-SX SFP", DESCR: "1000BASE-SX SFP"
PID: FTLF8519P2BNL-C6B , VID: B , SN: xxxx
%============
%remove SFP and added glc-sx-mm SFP, this is the supported MM SFPO for the 29xx rtr
sh inv
NAME: "1000BASE-SX SFP", DESCR: "1000BASE-SX SFP"
PID: SFBR-5766PZ-CS1 , VID: , SN: xxx
============
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID xxx
9 FastEthernet interfaces
3 Gigabit Ethernet interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
500472K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2921/K9 xxx
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc None None None
data None None None
Configuration register is 0x2102Problem solved.
MAJOR untested bug in IOS 15.0(1)M3 which was the default image when we bought the devices
*** AVOID IOS 15.0 series ***
there are several bugs related to SFPs like:
does does recognize SFP
des not recognize some EHWIC cards such as, but not limited to EHWIC 1GE-SFP-CU
CSCtj35792
c3900 : gigE SFP should switch to 1000/FD if other side has no nego
Externally found severe (Sev2) bug: M-More
CSCth28824
c3945 GE shows DOWN/DOWN as compare to SFP
Externally found moderate (Sev3) bug: R-Resolved
They were fixed in 15.0(1)M4 or later
You can check the caveats for this IOS Release 15.0M:
http://www.cisco.com/en/US/docs/ios/15_0/release/notes/150MCAVS.html -
WRT54G Wireless Router Will Not Assign a Network Address
A Linksys WRT54G router will not assign a network address when I access the router using a Linksys WPC600N wireless card. I have the same problem accessing the router with a TRENDnet TEW-621PC wireless adapter. Both wireless adapters are assigned network addresses when I use other wireless routers. Also, I have no problems being assigned a network address when I access the WRT54G router in question using an old 2WIRE 802.11b wireless card.
I have tried "Repairing" the connection, I have used ipconfig to "release" and "renew" the connection. However, each attempt fails to have a DHCP address assigned.
I am a visitor at the work location with the connection problem, the router works for others without any issues.
ThanksWell in such case .... you can try few settings on the wireless adapter ....
If you are using WLAN monitor .....
Click start >> All programs >> Linksys wireless monitor >> Click on "Profile" >> Delete all profiles >> Click "New" >> Type in the wireless network name >> Click next >> Configure the rest of the wireless settings same as in the router ...
At last point it shows .... all the configuration settings ...reconfirm that >> Click on connect ot a network & reboot the computer ...
After reboot see if it shows connected or not....
You can also use Static Ip in the configuration .... -
Cisco 1760 router will not recognize wic1-dsu-t1-v2 card in slots 3 or 4
My 1760 router will not recognize a wic1-dsu-t1-v2 card in slots 3 or 4. They only work in slots 1 & 2. Never saw this before where the same card would not work in different slots.
Need assistance.
Thanks,
Ron
Router#show version
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-IPBASE-M), Version 12.3(6c), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 20-Jul-04 07:00 by kellythw
Image text-base: 0x80008120, data-base: 0x80C74650
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
Router uptime is 20 minutes
System returned to ROM by power-on
System image file is "flash:c1700-ipbase-mz.123-6c.bin"
cisco 1760 (MPC860P) processor (revision 0x500) with 55598K/9938K bytes of memory.
Processor board ID FOC0849230K (3846615071), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
WIC T1-DSU
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router#show flash
System flash directory:
File Length Name/status
1 7517112 c1700-ipbase-mz.123-6c.bin
[7517176 bytes used, 25775112 available, 33292288 total]
32768K bytes of processor board System flash (Read/Write)
Router#show diag
Slot 0:
C1760 1FE VE 4SLOT DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 5.0
PCB Serial Number : FOC0849230K
Part Number : 73-7167-05
Board Revision : B0
Fab Version : 04
Product (FRU) Number : CISCO1760
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 16 41 05 00 C1 8B 46 4F 43 30 38 34
0x10: 39 32 33 30 4B 82 49 1B FF 05 42 42 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC/VIC Slot 0:
FT1 4351
Daughter card-Version 4 TLV Cookie Format
Hardware Revision : 1.1
PCB Serial Number : FOC09053XP1
Part Number : 73-8346-04
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product (FRU) Number : WIC-1DSU-T1-V2
Top Assy. Part Number : 800-22193-02
CLEI Code : IP4I380GAB
WIC/VIC Slot 1:
FT1 4351
Daughter card-Version 4 TLV Cookie Format
Hardware Revision : 1.2
PCB Serial Number : FOC10073JND
Part Number : 73-8346-05
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product (FRU) Number : WIC-1DSU-T1-V2
Top Assy. Part Number : 800-22193-03
CLEI Code : IPUIAPRRAAHi Ron,
Slots 3 & 4 are for VICs only.
Have a look at the Location/ Function table here:
http://www.cisco.com/en/US/products/hw/routers/ps221/products_tech_note09186a00800c3399.shtml
cheers,
Seb. -
Upgrade - SAP will not restart during MAIN_NEWBAS/STARTSAP_NBAS phase
We are upgrading from 4.7 to NW 7.0 (SP#5)
SAP will not restart during the phase MAIN_NEWBAS/STARTSAP_NBAS
We had to manually apply the kernel (NW 7.2 -#63 - NON UC). This looks OK when we calll DW -version. The T03 system will not start either through the upgrade tool or manually. There is no useful log in
\usr\sap\T03\DVEBMGS15\work
The upgrade tool reports this error.
Checks after phase MAIN_NEWBAS/STARTSAP_NBAS were negative!
Last error code set: RFC call to subst_get_uvers failed with key
RFC_ERROR_COMMUNICATION (open): SAP_CMINIT3 : rc=20 > Connect to SAP gateway failed Connect_PM GWHOST=CSIAS9, GWSERV=sapgw15, SYSNR=15
LOCATION CPIC (TCP/IP) on local host with Unicode
ERROR partner 'CSIAS9:3315' not reached
TIME Wed Aug 31 15:09:36 2011
RELEASE 720 COMPONENT NI (network interface)
VERSION 40 RC -10
MODULE nixxi.cpp
LINE 2898
DETAIL NiPConnect: 165.156.101.209:3315
SYSTEM CALL connect
ERRNO 79 ERRNO TEXT Connection refused
COUNTER 550
Thanks
MattThanks Rene, I have updated the ticket with the required information. In the mean time I am interested if anyone else had had a similar problem during an upgrade. We did have an initial error with the crtsidusr command ( setting CLASSICUSERCONCEPT + removing some of the SPCAUT) seemed to fix that. At this point the upgrade failed and we had to manually APYSAPKRN, the log shoewed it wanted the NON UC which was odd as we are including the UC in the upgrade.
Thanks -
Windows 8.1 will not download iTunes setup file
Windows 8.1 will not download iTunes setup file. It asks if I want to save the file. I click yes but it doesn't download. Tried numerous times on my new Toshiba Qosmio computer.
See the Further Information area of Troubleshooting issues with iTunes for Windows updates for download advice and direct links if required.
tt2 -
Menu Bar at top will not hide during full screen playback
URGENT!! Please help. I am playing a QT movie in version 7 on operating system 10.3.9 on an ibook. Despite selecting full screen mode the menu bar at the top will not disappear during playback. Have checked all preference settings. Any advice?
I am having the same problem. I have an iBook with system 10.3.9 running the newest version of QT. It worked at first, but then I used the menu once during a fullscreen play and the menu hasn't hidden since. And no, my cursor isn't stuck at the top of the screen.
-
Will not let me setup email account. says problem with email try again later
Icloud will not let me setup email @iclould.com. Say has a problem try again later?
Here's the iPhone email setup assistant:
iPhone Email Setup -
Wireless router will not recognize password
My wirelss router will not recognize the password on the router. Would like to change it to something wowrkable.
https://customer.comcast.com/help-and-support/Wireless-Gateway
http://customer.comcast.com/help-and-support/internet/wireless-gateway-username-and-password/
http://customer.comcast.com/help-and-support/internet/securing-wireless-gateway-network/
http://customer.comcast.com/help-and-support/internet/broadband-gateways-userguides
http://media2.comcast.net/anon.comcastonline2/support/userguides/Wireless_Gateway_User_Guide_030811.... -
WRT54G ver.6 wireless router will not connect either way
WRT5G ver.6 Router will not connect to the internet or other PCs wired nor wirelessly, PC shows "limited or No Connection". The orange light is not on and will not come on when I press the Cisco System Light/Button on front. I cannot access the router through the browser nor PING it through the command prompt. I have tried to reset it and unplug it for few seconds, please, me OBIWAN, your my only hope.
I think your router is bricked, You can try the steps on this link and check if it solves your problem or not.
-
Routing is not pickup during cost estimate
Hi,
We have created BOM & Routing,
Issues During SCE System will not taking Routing,
Parameter taken in consideration
Configuration & Master data maintenance
1) In Material master Base UOM maintained is EA alternate UOM MLD
2) Activity rate we have maintained : KG / KW / HR
2) Routing requirement is MLD.
In Routing IF i Maintained EA UOM, System will take Routing for SC,
Client requirement :Mafg production in MLD and EA, Activity should be MLD Base
Is their any config missing for UOM
Could u tel me.
Thanks in Advance.
Regards,
VINUDear Vinutha,
If my understanding is correct then you have to first define all the alternative unit of measurement(like issuing unit,production
unit,ordering unit,purchasing unit) in the respective material's additonal data in the material master.( 100 Ea = 100 MLD - For
example).
While defining routing,in the routing header for the material mention the unit(MLD) in which you will be defining the
operation,operation timings.
Check with settings whether the system is picking the routing during SCE in CK11N/CK40N.If my understanding is correct then
there is no configuration settings related to the same.
Check and revert back.
Regards
Mangalraj.S -
WRT54g not recognized during setup
I am trying to setup the WRT54G wireless router but for some reason the computers will not recognize it.
I tried the routers page 192.168.1.1 and that did not work. I tried easy link and that could not detect the router. When i use the CD it give me a router error during the checking status state of the setup.
any ideas on what the problem could be?
thanksTo worm1028 ---
You need to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you. -
"Storage is not configured" during failover - COH-1467 still not fixed?
I am runing a test program using two cache nodes and one "client JVM", all on the same machine (the first cache node is used as WKA). When I kill one of the cache nodes and the restart it again I get the following exceptions:
In the surviving cache node:
2009-01-22 08:01:14.753/112.718 Oracle Coherence GE 3.4.1/407 <Error> (thread=DistributedCache, member=1): An exception (java.lang.ClassCastException) occurred reading Message AggregateFilterRequest Type=31 for Service=DistributedCache{Name=DistributedCache, State=(SERVICE_STARTED), LocalStorage=enabled, PartitionCount=257, BackupCount=1, AssignedPartitions=257, BackupPartitions=0}
2009-01-22 08:01:14.753/112.718 Oracle Coherence GE 3.4.1/407 <Error> (thread=DistributedCache, member=1): Terminating DistributedCache due to unhandled exception: java.lang.ClassCastException
2009-01-22 08:01:14.753/112.718 Oracle Coherence GE 3.4.1/407 <Error> (thread=DistributedCache, member=1):
java.lang.ClassCastException: java.lang.Long
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$AggregateFilterRequest.read(DistributedCache.CDB:8)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onNotify(Grid.CDB:117)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache.onNotify(DistributedCache.CDB:3)
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:37)
at java.lang.Thread.run(Thread.java:619)
On the restarted cache node:
2009-01-22 08:01:15.722/2.220 Oracle Coherence GE 3.4.1/407 <Info> (thread=Main Thread, member=n/a): Loaded cache configuration from resource "file:/C:/Javaproj/Query/lib/master-coherence-cache-config.xml"
2009-01-22 08:01:16.565/3.063 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
2009-01-22 08:01:16.628/3.126 Oracle Coherence GE 3.4.1/407 <Info> (thread=Cluster, member=n/a): Failed to satisfy the variance: allowed=16, actual=31
2009-01-22 08:01:16.628/3.126 Oracle Coherence GE 3.4.1/407 <Info> (thread=Cluster, member=n/a): Increasing allowable variance to 17
2009-01-22 08:01:17.003/3.501 Oracle Coherence GE 3.4.1/407 <Info> (thread=Cluster, member=n/a): This Member(Id=5, Timestamp=2009-01-22 08:01:16.768, Address=138.106.109.121:54101, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22728, Edition=Grid Edition, Mode=Development, CpuCount=2, SocketCount=1) joined cluster with senior Member(Id=1, Timestamp=2009-01-22 07:59:24.098, Address=138.106.109.121:54100, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22948, Edition=Grid Edition, Mode=Development, CpuCount=2, SocketCount=1)
2009-01-22 08:01:17.065/3.563 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=n/a): Member(Id=4, Timestamp=2009-01-22 08:00:35.566, Address=138.106.109.121:8088, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:11544) joined Cluster with senior member 1
2009-01-22 08:01:17.081/3.579 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=n/a): Member 1 joined Service Management with senior member 1
2009-01-22 08:01:17.081/3.579 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=n/a): Member 1 joined Service InvocationService with senior member 1
2009-01-22 08:01:17.081/3.579 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=n/a): Member 1 joined Service DistributedCacheNoBackup with senior member 1
2009-01-22 08:01:17.097/3.595 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=n/a): Member 4 joined Service InvocationService with senior member 1
2009-01-22 08:01:17.097/3.595 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=n/a): Member 4 joined Service DistributedCache with senior member 4
2009-01-22 08:01:17.222/3.720 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): TcpRing: connecting to member 4 using TcpSocket{State=STATE_OPEN, Socket=Socket[addr=/138.106.109.121,port=8088,localport=3609]}
2009-01-22 08:01:17.253/3.751 Oracle Coherence GE 3.4.1/407 <D5> (thread=Invocation:Management, member=5): Service Management joined the cluster with senior service member 1
2009-01-22 08:01:17.393/3.891 Oracle Coherence GE 3.4.1/407 <D5> (thread=Invocation:InvocationService, member=5): Service InvocationService joined the cluster with senior service member 1
2009-01-22 08:01:18.643/5.141 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 joined Service DistributedCache with senior member 4
2009-01-22 08:01:19.050/5.548 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 left service DistributedCache with senior member 4
2009-01-22 08:01:23.659/10.157 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 joined Service DistributedCache with senior member 4
2009-01-22 08:01:24.284/10.782 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 left service DistributedCache with senior member 4
2009-01-22 08:01:28.674/15.172 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 joined Service DistributedCache with senior member 4
2009-01-22 08:01:29.503/16.001 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 left service DistributedCache with senior member 4
2009-01-22 08:01:33.674/20.172 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 joined Service DistributedCache with senior member 4
2009-01-22 08:01:33.721/20.219 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 left service DistributedCache with senior member 4
2009-01-22 08:01:38.674/25.172 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 joined Service DistributedCache with senior member 4
2009-01-22 08:01:38.956/25.454 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 left service DistributedCache with senior member 4
2009-01-22 08:01:43.690/30.188 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 joined Service DistributedCache with senior member 4
2009-01-22 08:01:44.174/30.672 Oracle Coherence GE 3.4.1/407 <D5> (thread=Cluster, member=5): Member 1 left service DistributedCache with senior member 4
2009-01-22 08:01:47.659/34.157 Oracle Coherence GE 3.4.1/407 <Error> (thread=Main Thread, member=5): Error while starting service "InvocationService": com.tangosol.net.RequestTimeoutException: Timeout during service start: ServiceInfo(Id=2, Name=InvocationService, Type=Invocation
MemberSet=ServiceMemberSet(
OldestMember=Member(Id=1, Timestamp=2009-01-22 07:59:24.098, Address=138.106.109.121:54100, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22948)
ActualMemberSet=MemberSet(Size=3, BitSetCount=2
Member(Id=1, Timestamp=2009-01-22 07:59:24.098, Address=138.106.109.121:54100, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22948)
Member(Id=4, Timestamp=2009-01-22 08:00:35.566, Address=138.106.109.121:8088, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:11544)
Member(Id=5, Timestamp=2009-01-22 08:01:16.768, Address=138.106.109.121:54101, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22728)
MemberId/ServiceVersion/ServiceJoined/ServiceLeaving
1/3.1/Thu Jan 22 07:59:27 CET 2009/false,
4/3.1/Thu Jan 22 08:00:36 CET 2009/false,
5/3.1/Thu Jan 22 08:01:17 CET 2009/false
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onStartupTimeout(Grid.CDB:6)
at com.tangosol.coherence.component.util.daemon.queueProcessor.Service.start(Service.CDB:27)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.start(Grid.CDB:38)
at com.tangosol.coherence.component.util.SafeService.startService(SafeService.CDB:28)
at com.tangosol.coherence.component.util.SafeService.ensureRunningService(SafeService.CDB:27)
at com.tangosol.coherence.component.util.SafeService.start(SafeService.CDB:14)
at com.tangosol.net.DefaultConfigurableCacheFactory.ensureService(DefaultConfigurableCacheFactory.java:841)
at com.tangosol.net.DefaultCacheServer.start(DefaultCacheServer.java:140)
at com.tangosol.net.DefaultCacheServer.main(DefaultCacheServer.java:61)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.intellij.rt.execution.application.AppMain.main(AppMain.java:90)
Exception in thread "Main Thread" com.tangosol.net.RequestTimeoutException: Timeout during service start: ServiceInfo(Id=2, Name=InvocationService, Type=Invocation
MemberSet=ServiceMemberSet(
OldestMember=Member(Id=1, Timestamp=2009-01-22 07:59:24.098, Address=138.106.109.121:54100, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22948)
ActualMemberSet=MemberSet(Size=3, BitSetCount=2
Member(Id=1, Timestamp=2009-01-22 07:59:24.098, Address=138.106.109.121:54100, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22948)
Member(Id=4, Timestamp=2009-01-22 08:00:35.566, Address=138.106.109.121:8088, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:11544)
Member(Id=5, Timestamp=2009-01-22 08:01:16.768, Address=138.106.109.121:54101, MachineId=36217, Location=site:global.scd.scania.com,machine:N27858,process:22728)
MemberId/ServiceVersion/ServiceJoined/ServiceLeaving
1/3.1/Thu Jan 22 07:59:27 CET 2009/false,
4/3.1/Thu Jan 22 08:00:36 CET 2009/false,
5/3.1/Thu Jan 22 08:01:17 CET 2009/false
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onStartupTimeout(Grid.CDB:6)
at com.tangosol.coherence.component.util.daemon.queueProcessor.Service.start(Service.CDB:27)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.start(Grid.CDB:38)
at com.tangosol.coherence.component.util.SafeService.startService(SafeService.CDB:28)
at com.tangosol.coherence.component.util.SafeService.ensureRunningService(SafeService.CDB:27)
at com.tangosol.coherence.component.util.SafeService.start(SafeService.CDB:14)
at com.tangosol.net.DefaultConfigurableCacheFactory.ensureService(DefaultConfigurableCacheFactory.java:841)
at com.tangosol.net.DefaultCacheServer.start(DefaultCacheServer.java:140)
at com.tangosol.net.DefaultCacheServer.main(DefaultCacheServer.java:61)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.intellij.rt.execution.application.AppMain.main(AppMain.java:90)
2009-01-22 08:01:47.659/34.157 Oracle Coherence GE 3.4.1/407 <Error> (thread=Invocation:InvocationService, member=5): validatePolls: This service timed-out due to unanswered handshake request. Manual intervention is required to stop the members that have not responded to this Poll
PollId=1, active
InitTimeMillis=1232607677393
Service=InvocationService (2)
RespondedMemberSet=[1]
LeftMemberSet=[]
RemainingMemberSet=[4]
2009-01-22 08:01:47.659/34.157 Oracle Coherence GE 3.4.1/407 <D5> (thread=Invocation:InvocationService, member=5): Service InvocationService left the cluster
2009-01-22 08:01:47.659/34.157 Oracle Coherence GE 3.4.1/407 <D4> (thread=ShutdownHook, member=5): ShutdownHook: stopping cluster node
Process finished with exit code 1
On the client JVM:
2009-01-22 08:01:14.815/41.265 Oracle Coherence GE 3.4.1/407 <D5> (thread=Invocation:InvocationService, member=4): Repeating AggregateFilterRequest due to the re-distribution of PartitionSet[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81, 82, 83, 84, 85, 86, 87, 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98, 99, 100, 101, 102, 103, 104, 105, 106, 107, 108, 109, 110, 111, 112, 113, 114, 115, 116, 117, 118, 119, 120, 121, 122, 123, 124, 125, 126, 127]
java.lang.RuntimeException: Storage is not configured
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.onMissingStorage(DistributedCache.CDB:9)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.ensureRequestTarget(DistributedCache.CDB:33)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.sendPartitionedRequest(DistributedCache.CDB:31)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.aggregate(DistributedCache.CDB:11)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$ViewMap.aggregate(DistributedCache.CDB:52)
at com.tangosol.coherence.component.util.SafeNamedCache.aggregate(SafeNamedCache.CDB:1)
at com.tangosol.net.cache.NearCache.aggregate(NearCache.java:453)
at com.scania.oas.coherence.invocables.ValueQueryInvocable.typeSearch(ValueQueryInvocable.java:260)
at com.scania.oas.coherence.invocables.ValueQueryInvocable.queryStringFirstSearch(ValueQueryInvocable.java:300)
at com.scania.oas.coherence.invocables.ValueQueryInvocable.run(ValueQueryInvocable.java:135)
at com.scania.oas.coherence.invocables.InvocableWrapper.run(InvocableWrapper.java:54)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.InvocationService.onInvocationRequest(InvocationService.CDB:10)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.InvocationService$InvocationRequest.onReceived(InvocationService.CDB:40)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onMessage(Grid.CDB:9)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onNotify(Grid.CDB:130)
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:37)
at java.lang.Thread.run(Thread.java:619)
java.lang.RuntimeException: Storage is not configured
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.onMissingStorage(DistributedCache.CDB:9)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.ensureRequestTarget(DistributedCache.CDB:33)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.sendPartitionedRequest(DistributedCache.CDB:31)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$BinaryMap.aggregate(DistributedCache.CDB:11)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.DistributedCache$ViewMap.aggregate(DistributedCache.CDB:52)
at com.tangosol.coherence.component.util.SafeNamedCache.aggregate(SafeNamedCache.CDB:1)
at com.tangosol.net.cache.NearCache.aggregate(NearCache.java:453)
at com.scania.oas.coherence.invocables.ValueQueryInvocable.queryStringSearch(ValueQueryInvocable.java:268)
at com.scania.oas.coherence.invocables.ValueQueryInvocable.queryStringFirstSearch(ValueQueryInvocable.java:297)
at com.scania.oas.coherence.invocables.ValueQueryInvocable.run(ValueQueryInvocable.java:135)
at com.scania.oas.coherence.invocables.InvocableWrapper.run(InvocableWrapper.java:54)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.InvocationService.onInvocationRequest(InvocationService.CDB:10)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.InvocationService$InvocationRequest.onReceived(InvocationService.CDB:40)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onMessage(Grid.CDB:9)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onNotify(Grid.CDB:130)
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:37)
at java.lang.Thread.run(Thread.java:619)
I even tried to re-write the "run method" in tthe invocable in a way that caused it to, in a loop, perform a delay and then re-try its calculations when it received a runtime exception with the text "Storage is not configured" causing the retreival a new named cache each time but this did not help - it never seemed to recover...
Since I dont see any of my application classes in the "class cast" trace-back I assume it is an Coherence internal problem or can you thiink about some user programming error that could cause it? I am by the way not using any long or "Long in my application...
Best Regards
MagnusHi Magnus,
The log you provided seems to indicate that the problem was caused by the de-serialization of the “AggregateFilterRequest” message. The only explanation we have is that you are using a custom Filter that has asymmetrical serialization/deserialization routines, causing this failure. Could you please send us the corresponding client code?
Meanwhile, we will open a JIRA issue, to make sure that Coherence handles this kind of error more gracefully.
-David
Maybe you are looking for
-
Hello, I have a problem by LED function inspection test. This is on Vision Builder AI program. There is a camera, it captures an image. The images have a little different gain, brightness, contrast values, so the later inspections have different meas
-
Error in SQL Developer: Database Connections has no JNDI context so cannot
Hello, I have installed SQL Developer 3.1.07 version on Linux. Previously I was able to create a connection and browse the existing tables, add tables, etc. Now when I launch SQL Developer, I see that no connections are displayed. Instead there are t
-
I'm using Firefox 5.0 on a desk top.
-
JFileChooser file name extention queistion
hi i would like to know if it is possible to place a file extention in the filename section when you open the save dialog. So as when the user types a file name in the file extention is added automaticly to only allow the user to save in .png. My cod
-
After purchasing the new macbook pro and downloading all my informatoin onto it I realized the computer is defective...So I'm returning it back to amazon..I just want to make sure all my information is deleted before I send it back. I have my old mac