WRT310N - Connection stability issues

I got this router last Thursday and set it up over the weekend. When it works, it's been fantastic. I have the latest firmware version running, and with that, when connected all of the PCs in my house have a 100% signal strength and excellent signal quality. The two N connections are at 130.0 Mbps and the two G connections are at 54.0 Mbps. All is good. Except that after 12 to 14 hours, the Access Point just disappears. Even the computer that connects wirelessly from about 15 feet away can't see it anymore. So far the only solution has been to reboot everything (router and all PCs). Rebooting the router doesn't help without rebooting the PCs as well. Once rebooted, everything works, and the countdown begins again. The wired portion of the router always seems to work. Any ideas?

I certainly don't claim to have the "magic bullet" that takes care of this, but I was having the same problems when I first set up my WRT310N as well. I messed with all of the advanced wireless settings and such to no avail. But then I was reading another post here that got me thinking. The default DHCP lease given out by the router is good for 24 hours, and nearly every network device in my home was DHCP. And, according to the router's status pages, their leases were all set to expire about the same time. I was never able to verify if that was the cause of the overnight lockups, but I did the whole re-flash and re-set, and then asigned DHCP reservations to each of those devices. This way, I could still set them up as DHCP and not have to worry about IP addresses, DNS, etc., but apparently the router deals with them differently as "normal" DHCP leases. Whether that truly was the problem or not, I have not had my router go down since I did that nearly a week ago. Maybe this info will help someone else as well (or maybe even Linksys).

Similar Messages

Low SNR, Causing Connection Stability Issues?

Hello I'm not using the HomeHub so I cant post the usual home hub image however I shall post the one from my Netgear.
Normally I get about 5.5MB downloads so the line sync's somewhere around 6000 ish? With 4-6DB line margins, at this the line stays connected for months at a time no issues. However today my noise margin has dropped to to 0-1DB causing my sync rate to go up and rendering the line very unstable. I have tried to restart the Internet multiple times hoping this would increase the noise margin and return it to being stable to no affect. Can anyone give me a hand getting it back up to between 4-6 where my line is very stable and perhaps fixing it there?
Thanks Carl.
Solved!
Go to Solution.

Hi imjolly,
We have 1 Main socket which has ADSL v1.0 written on the front that splits broadband and phone as soon as it enters. A BT engineer gave it us when he visited a while ago. Off this the router is connected to the broadband socket straight away with prob <5ft of cable (Standard stuff that comes with the homehub).
The phone side has a splitter and extenstions plugged into it however i did try unplugging them and just leaving the phone plugged in next to the master socket and it seemed to made no difference.
I will try dissconnecting the cable as you have sugested hopefully this will help.
Thanks for the help.

A1000 Wifi connection stability issue

I just received this A1000F tablet on last Friday. The wifi connection randomly stops responding, while the notification bar show it as connected. When it occurs, router activity panel reports it as inactive. Switching wifi ON/OFF on the tablet restores the connection for a random limited time. I tried many Wifi authentication setups without sucess. My other devices as Airport Express, Acer Laptop and Sony Xperia U work flawlessy with connection staying up for days without any simmilar issue. Device has been updated to latest available upgrade (Settings > About Device > System upgrade)
Kind regards

Experiencing this problem too but with some routers only

Lenovo Yoga 10 HD+ WIFI connection stability issue

Same problem here but on Lenovo Yoga 10 HD+ 3G:
After a few minutes the connection is gone though the tablet shows its still there at full level. Disabling / Enabling WIFI on the tablet makes it reconnect. On the same router e.g. Lenovo Yoga 8 Wifi Edition, Samsung Galaxy S3 and S3 mini all work fine and do keep the connection. Tested with latest firmware released OTA yesterday.
Also tried the Yoga 10 HD+ on two other WLAN routers where it worked fine.
Any ideas except for buying a new router?
Moderator Note; post moved to start new thread on specific system

I'm having the very same problem. I bought a Lenovo Yoga 10 tablet about a week ago and updated it to 4.4.2 (B8000_A442_001_021_140703_WW_WIFI) yesterday and ever since then, my wifi kicks out when I'm browsing, reading emails, checking twitter etc just all of a sudden and I have to disable and re-enable my Wifi for it to work again (aprox. 5-20 minutes until I have to reconnect again). I've not changed anything in my router settings (Netgear CG3100) since the upgrade and every other computer, tablet and phones that we have in our house runs all fine, it's just the Yoga tablet where I have this issue with. I really hope an update/fix could be pushed as soon as possible since it's unbearable to use it right now and I might just have to return it to the shop in exchange for another tablet, which I don't really want (love the battery life).
Eitherway, I'd be thankful for any help/fix or responds from Lenovo.

Communications Suite 6u1 stability issue

Hello,
I have a stability issue with Comm Suite 6 Update 1.
imsimta version
Sun Java(tm) System Messaging Server 7.0-3.01 64bit (built Dec 9 2008)
libimta.so 7.0-3.01 64bit (built 09:57:35, Dec 9 2008)
Using /opt/sun/comms/messaging64/config/imta.cnf
SunOS apollo2 5.10 Generic_138888-01 sun4v sparc SUNW,-T5220The server was installed as Communications Suite 6 and I upgraded it to U1 2 weeks ago.
Last weekend I put the whole system into production but unfortunately the SMTP demon hangs from time to time.
Here is some messages from different log files:
From default log:
[08/Jan/2009:16:36:08 +0200] apollo2 stored[11346]: General Warning: imapd process 10622 exited abnormally
[08/Jan/2009:16:36:08 +0200] apollo2 stored[11346]: Store Warning: stored: Sun Java(tm) System Messaging Server STORE 7.0-3.01 64bit (built Dec 9 2008) starting up
[08/Jan/2009:16:36:11 +0200] apollo2 impurge[11347]: General Notice: impurge started
[08/Jan/2009:16:36:13 +0200] apollo2 imsched[11350]: General Notice: starting up
[08/Jan/2009:17:45:01 +0200] apollo2 msprobe[11881]: General Error: cannot connect to port 25: Connection refused
[08/Jan/2009:17:45:01 +0200] apollo2 msprobe[11881]: General Critical: SMTP server is not responding
[08/Jan/2009:17:45:01 +0200] apollo2 msprobe[11881]: General Warning: dispatcher process is not running, but does not appear to have crashed. No restart requested.
[08/Jan/2009:17:45:01 +0200] apollo2 msprobe[11881]: General Error: cannot connect to port 587: Connection refused
[08/Jan/2009:17:45:01 +0200] apollo2 msprobe[11881]: General Critical: SMTP_SUBMIT server is not responding
[08/Jan/2009:17:51:56 +0200] apollo2 imsched[11350]: General Notice: shutting down
[08/Jan/2009:17:51:56 +0200] apollo2 impurge[11347]: General Notice: impurge finished
[08/Jan/2009:17:51:56 +0200] apollo2 stored[11346]: General Warning: imapd process 11348 exited abnormally
[08/Jan/2009:17:51:56 +0200] apollo2 stored[11346]: Store Warning: stored: Sun Java(tm) System Messaging Server STORE 7.0-3.01 64bit (built Dec 9 2008) shutting down
[08/Jan/2009:17:56:35 +0200] apollo2 stored[1324]: Store Warning: stored: Sun Java(tm) System Messaging Server STORE 7.0-3.01 64bit (built Dec 9 2008) starting up
[08/Jan/2009:17:56:39 +0200] apollo2 impurge[1325]: General Notice: impurge started
[08/Jan/2009:17:56:48 +0200] apollo2 imsched[1328]: General Notice: starting up
From watcher log
Watched 'dispatcher' process 11352 exited abnormally
[08/Jan/2009:16:39:42 +0200] (Notice) Received request to restart: dispatcher
[08/Jan/2009:16:39:42 +0200] (Notice) Connecting to watcher ...
[08/Jan/2009:16:39:42 +0200] (Notice) dispatcher server is not running
[08/Jan/2009:16:39:42 +0200] (Notice) Starting dispatcher server .... 11435
Watched 'dispatcher' process 11435 exited abnormally
[08/Jan/2009:17:40:43 +0200] (Notice) Received request to restart: dispatcher
[08/Jan/2009:17:40:43 +0200] (Notice) Connecting to watcher ...
[08/Jan/2009:17:40:43 +0200] (Notice) dispatcher server is not running
[08/Jan/2009:17:40:43 +0200] (Notice) Starting dispatcher server .... 11860
Watched 'dispatcher' process 11860 exited abnormally
[08/Jan/2009:17:44:19 +0200] (Notice) Received request to restart: dispatcher
[08/Jan/2009:17:44:19 +0200] (Notice) Connecting to watcher ...
[08/Jan/2009:17:44:19 +0200] (Error) dispatcher failed twice in 600 seconds, will not perform restart
watcher process 1322 started at Thu Jan 8 17:56:33 2009The dispatcher.log* and tcp_smtp_server.log* are always empty.
The mail.log_current has this at the hanging moment:
08-Jan-2009 17:44:19.84 tcp_local    +            O [unknown] SMTP
08-Jan-2009 17:44:19.84 tcp_local    +            X [unknown] SMTP Error writing SMTP packetThe problem repeats from time to time and I have to restart the mail server manually.
There are no core dumps in the system and system logs are OK.
There are latest patches installed and the system is very stable itself except SMTP part of CommSuite.
The auto restart is enabled out of the box.
configutil -o local.autorestart
yesThe server is almost idle. It serves 10 people and there are just few mails going via it.
Obviously there is something wrong with my configuration or it's a bug.
Could someone help me to understand the reason of such instability?

Hello Shane,
I appreciate you help.
The dispatcher process crashes by itself, nobody kills it manually :)
The coreadm has been enabled from the installation date and there is just one old core dump for some java process.
coreadm
     global core file pattern: /var/core/core.%f
     global core file content: default
       init core file pattern: core
       init core file content: default
            global core dumps: enabled
       per-process core dumps: disabled
      global setid core dumps: disabled
      per-process setid core dumps: disabled
     global core dump logging: disabled
ls -la /var/core
total 126918
drwxr-xr-x   2 root     root         512 Jan 4 12:34 .
drwxr-xr-x 47 root     sys         1024 Sep 14 19:28 ..
-rw-r--r--   1 root     root           8 Sep 26 18:32 .nsr
-rw-------   1 root     root     75235729 Jan 4 12:34 core.javaNow I changed coreadm to this:
coreadm
     global core file pattern: /var/core/core.%f
     global core file content: default
       init core file pattern: core
       init core file content: default
            global core dumps: enabled
       per-process core dumps: disabled
      global setid core dumps: enabled
per-process setid core dumps: disabled
     global core dump logging: enabledOK. Next time I will use "imsimta restart" but this does not solve the problem.
I used /opt/sun/comms/messaging64/bin/stop-msg, /opt/sun/comms/messaging64/bin/start-msg commands to do this.
The problem I have is SMTP service stops to work and I cannot receive any emails until I do a restart .
Can I turn on some additional logging either for dispatcher or for SMTP process?
Any ideas how to make it work stable?
Best Regards,
Victor

InDesign CS5 Stability Issues

I got really fed up today.
Trying to resize a magazine, all the articles are individual documents compiled in a book. So each "chapter" is at least 3 pages and at most 15.
I adore the spanning columns feature, I've got sevral articles that this is very handy to setup. But I find the whole program is completely unstable when using this feature.
I started removing the anchored text frames and applying the spanning columns for the headers, with a paragraph rule above for the background colour.
But if I click around too quickly the whole program freezes and won't budge. I could be selecting an anchored frame to remove it. Or changing paragraph style, or simply opening another panel.
I checked the Task Manager and watched for 15 minutes as InDesign consumed more and more memory - going from 150k to 650k in about 10 minutes.
This happened a bunch of times. I restarted, reset my prefs, exported to idml, and all the other nick nack fixes.
Indesign just keeps bombing out. At which point i have to end the process and then restart indesign and I lose a tiny bit of work.
So frustrated today - over seemingly simple tasks, like selecting something, and the program crashes. This behaviour does not happen when I am not using Span Columns.
Is anyone else having stability issues with CS5 and Spanned Columns?

Thanks Bob
I thought myself that there was a lot going on. And I appreciate that. But thinking about it, the only addition here is the spanning of columns and balanced columns.
I was at one stage incorpartaing detect edges on an image and had to give up on it because there was a 3 minute delay on simple things like cutting the image (as a test).
I just feel that perhaps more could be done in speeding up InDesign.
I've had a hard enough time updating the software, upgrading the hardware is going to be tough.
I don't think Indesign CS5 minimum specs included a supercomputer either?
Check
Intel® Pentium® 4 or AMD Athlon® 64 processor
Check
Microsoft® Windows® XP with Service Pack 2 (Service Pack 3 recommended); Windows Vista® Home Premium, Business, Ultimate, or Enterprise with Service Pack 1; or Windows 7
check
1GB of RAM (2GB recommended)
Check
1.6GB of available hard-disk space for installation; additional free space required during installation (cannot install on removable flash-based storage devices)
Check
1024x768 display (1280x800 recommended) with 16-bit video card
Check
DVD-ROM drive
Check
Adobe® Flash® Player 10 software required to export SWF files
Check
Broadband Internet connection required for online services*
Far too slow, far too unstable.

GS60/GS70-2PC/2PE Stealth/Ghost/Pro stability issues, solution

Hi guys,
If you have GS70 2PC Stealth,GS70 2PE Stealth Pro, GS60 2PC Ghost or GS60 2PE Ghost Pro
and experience stability issue,
flash your vbios as followed:
GS70 2PC Stealth for GTX860M, download vbios package: >>GTX860M<<
GS70 2PE Stealth Pro for GTX870M, download vbios package: >>GTX870M<<
GS60 2PC Ghost for GTX860M, download vbios package: >>GTX860M<<
GS60 2PE Ghost Pro for GTX870M, download vbios package: >>GTX870M<<
Flashing Instructions:
DOS:
guide1[by MSI]: how to: http://www.msi.com/files/pdf/VBIOS_Update_under_DOS_mode_EN.pdf
[flashing instruction are included in this SOP pdf]
guide2[Forum guide]: [more clear and detailed]
Create bootable USB key http://www.bay-wolf.com/usbmemstick.htm
once done extract all files from archive file to the USB key,
reboot your notebook enter in BIOS Setup and set boot mode to legacy, then save and exit.
and boot from the USB key [press F11 during BIOS post/logo screen then select your USB key]
when you see A:\ or C:\, type:
cd 860M [ENTER] or cd 870M [ENTER], depend which kind of GPU you are going to flash.
FVBIOS.bat [ENTER]
confirm with "Y" when asked and wait to finish,
then reboot your notebook enter in BIOS setup and set boot mode back to UEFI, then save and exit.
Windows: [Forum guide and the most easy way for flashing]
Extract all files from archive file to some folder.
Then go to Nvidia Control Panel, and select "Adjust image settings with preview":
and leave it in that way [don't close it]
then go back to the folder where you extracted all files,
and double click on FVBIOS.bat
confirm with "Y" when asked and wait to finish,
then reboot your notebook.
NOTE: Make sure that both battery and ac power cord are connected to the notebook before proceed

Quote from: Majed_c on 27-May-14, 14:59:11
Thank you for reply. I think I downloaded the right stuff since the downloaded file's name was <860M>. I will download the vbios via msi gs60 offical page and go by dos mode. But do you recommend to flash it cuz i did run 3d mark 11 for 3-4 hours constantly and found no error to force quit. All I concert is fan speed (min. 3333 rpm for normal use from the DGC interface) and the noise but I am not sure if the new vbios can do anything good about that. Thanks again.
Quote from: Majed_c on 27-May-14, 14:59:11
Thank you for reply. I think I downloaded the right stuff since the downloaded file's name was <860M>
they both are named 860M
You have to click on the hotlinks makred with << >>
to get the right one for your notebook, depend if its for GS60 or GS70 they are different hotlinks provided.
here is direct link to correct vbios for your notebook:
https://forum-en.msi.com/index.php?action=dlattach;topic=180211.0;attach=13131

My Internet Connection Dropping Issues...

I too am having the occasional Internet connection dropping issues. Phone and TV continue to work.
Since I had Fios installed last November I am on my third ONT and 2nd router. When I called in my latest drop yesterday the call center person told me I had a hardware issue because my computer had a valid IP address assigned. I tried to teach her something about DHCP but she would not listen to me. I asked her to please reboot the ONT and she refused because "nothing was indicating a problem with it". Whatever...
Each time the Internet goes out the router acts fat and happy. I have full green on WAN Coax, and strangely enough, a flashing green Internet activity indicator. Logging into the router shows that I am MOCA connected and assigned a WAN IP address. But I can't get out past the router at all. On the event that led to me getting a replacement router the lady said she could talk to the ONT just fine, but not the router. We reset the router and ONT port numerous times and the connection finally came back up.
I am not sure of the protocol between the ONT and router, but I think the ONT is keeping enough signal going to make the router "think" its happy, but then the ONT is not passing packets at some point. After yesterdays call and the refusal to reset the ONT I just hung up on her and reset it myself. Of course everything started working just fine...like I thought it would.
So what is the issue here? Is MOCA a mess? Is an Ethernet connection to the ONT better? I am utterly disgusted with this miserable system and can't afford to continue having these outages.
I should also add the other wonderful features I have seen. When I tried to powercycle the *new* router yesterday it decided to dump its entire config including my port forwarding. Nice... And I have given up using wireless because if I set the router for WPA it locks up so hard that it takes a master reset to get going again.
Anyone have some advice on getting this system stable?

I would try using a non-verizon router. I used the Netgear router and it fixed my problem. The Verizon router seem to be pieces of garbage and they over-hear.

Massive stability issues - Disk Utility repair failed, hardware test failed

Hi,
I am having massive stability issues. The installer will not install anything, programs are quitting randomly, and it is getting very annoying!
I read through a lot of posts and I have attempted to:
Repair my disk using the install cd: but that failed.
I did a Hardware test: but i had an error relating to fonts (?), couldn't see anything on the screen and I couldn't do anything.
Is there something else I could do that I haven't tried?
I have had my PB for a little over a year and have had no issues like this before. All of these issues seemed to start when I was playing a game and it suddenly just quit; I then couldn't go back into the game or re-install the game.
Help!!
12" Powerbook G4 1.5Ghz Mac OS X (10.4.6) 768 RAM

Hi, Dan.
You wrote: "Repair my disk using the install cd: but that failed."That's a big problem. You won't get very far until the problems noted by Repair Disk, the function I presume you ran based on your description, are sorted out. It's possible the hard drive has failed.
If the Apple Hardware Test failed, that's another significant problem. If it produces messages you can read that describe the failure, write them down. The machine may need to be serviced by an Apple Authorized Service Provider.
As to your next steps, first run the procedure specified in my "Resolving Disk, Permission, and Cache Corruption" FAQ. Perform the steps therein in the order specified to see what's up with your disk and if anything can be done to correct that.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

Shared libary gives error in 10.1.0.3 on AIX 5.2. Is it Stability Issue

Hi,
I am trying to make a shared library immediately after the server installation for my 32bit MicroFocus COBOL
application which is running fine on 8.1.7.4
make LIBDIR=lib32 LOC_RTSORA=libmfora.so -f ins_precomp.mk libmfora.so
After that I copy the libmfora.so into $ORACLE_HOME/lib32
later I try to prepare the runtime using
cob32 -vxo rts32 -e "" -L $ORACLE_HOME/lib32 -l mfora $ORACLE_HOME/precomp/lib32/cobsqlintf.o
It creates successfully but when I run it I get this error
> rts32 > err.txt
exec(): 0509-036 Cannot load program rts32 because of the following errors:
0509-130 Symbol resolution failed for /data/oracle/product/10.1.0.3/lib32/libnnz10.so because:
0509-136 Symbol SSL_ALG_ANSIPRNG_BS (number 67) is not exported from
dependent module rts32.
0509-136 Symbol SSL_ALG_CIPHER_DHE_DSS_EXPORT1024_WITH_DES_CBC_SHA_CLIENTSIDE_BS (number 68) is not exported f
rom
dependent module rts32.
0509-136 Symbol SSL_ALG_CIPHER_DHE_DSS_EXPORT1024_WITH_DES_CBC_SHA_SERVERSIDE_BS (number 69) is not exported f
rom
dependent module rts32.
0509-136 Symbol SSL_ALG_CIPHER_DHE_DSS_EXPORT1024_WITH_RC4_56_SHA_CLIENTSIDE_BS (number 70) is not exported fr
om
dependent module rts32.
0509-136 Symbol SSL_ALG_CIPHER_DHE_DSS_EXPORT1024_WITH_RC4_56_SHA_SERVERSIDE_BS (number 71) is not exported fr
om
dependent module rts32.
0509-136 Symbol SSL_ALG_CIPHER_DHE_DSS_EXPORT_WITH_DES40_CBC_SHA_CLIENTSIDE_BS (number 72) is not exported fro
m
dependent module rts32.
0509-136 Symbol SSL_ALG_CIPHER_DHE_DSS_EXPORT_WITH_DES40_CBC_SHA_SERVERSIDE_BS (number 73) is not exported fro
m
dependent module rts32.
0509-136 Symbol SSL_ALG_CIPHER_DHE_DSS_WITH_3DES_EDE_CBC_SHA_CLIENTSIDE_BS (number 74) is not exported from
dependent module rts32.
Previously when we run rts32 we should get this message
> rts32
V4.0 revision 0 build 10/10/2 G; 20504. Run Time System RXCAK/AA0/00000S
Without creating the shared library when I just the rtsora32 then also I get this error
> rtsora32
exec(): 0509-036 Cannot load program rtsora32 because of the following errors:
0509-130 Symbol resolution failed for /data/oracle/product/10.1.0.3/lib32/libnnz10.so because:
0509-136 Symbol ssl_GetPeerCertData (number 225) is not exported from
dependent module rtsora32.
0509-136 Symbol ssl_SetCertRef (number 232) is not exported from
dependent module rtsora32.
0509-192 Examine .loader section symbols with the
'dump -Tv' command.
Somebody help us to solve this issue
Is this because of any stability issues of 10.1.0.3 for AIX
Regards
Ajay

10.1.0.3 is a patchset, not a full release. Patchset are available on metalink , not on OTN.
You can have many databases related to a specific ORACLE_HOME, as long as your system has enough resources to handle these databases. When you create a new database there's no need to stop running database instances.
Installation guide and release notes for 10.2 + certify section of metalink have all informations concerning OS requirements.
Werner

Performance / stability issues with BDB 3.3.62 while checkpointing

Hi,
first of all: we use BDB 3.2 for more than a year within our application and we never had any performance or stability issues. Now we are about to release a new version of our software with BDB 3.3 and we found some problems during our release tests.
This is the situation: we have implemented some cleanup routines that make very heavy use of the BDB environment. The common usage pattern is to scan the database (about 300GB with >> 100 million items) and than delete a lot of items from the database. The first versions of our cleanup routine worked without any problem but during performance tuning of our code we suddenly and reproducible encountered segmentation faults in the com.sleepycat.je.recovery.Checkpointer thread. We analysed more that 10 VM crashes and ALL crashes were related to Checkpointer thread. (Linux 64 bit, JDK 1.5.0_013 / 1.6.0_06)
After we removed our performance tuning (only application logic – nothing BDB-related) the VM crashes disappeared – so it looks like some kind of problem which only occurs under high load conditions. Next thing we tried was enabling our performance tuning and setting Ceckpointer configuration to default (write a checkpoint after 20MB) before that we used time based checkpointing with 60 sec interval.
With Default Checkpointer configuration there were no VM-crashes but performance was very slow!
Finally my question: What Checkpointer configuration would you recommend for an environment that is under very high load with regard to delete operations? Would you recommend using “high priority Checkpointing”? Would you recommend time- or data-based checkpointing?
It looks like Checkpointing every 60 seconds was not a good idea but 20MB seems to be too slow.
This leads to another question: What does a longer Checkpointing interval mean for recovery time? Does recovery take substantially longer if checkpointing is done less fequently?
Any help would be very much apprechiated.
Here are two HS_ERR_PID
# An unexpected error has been detected by Java Runtime Environment:
# SIGSEGV (0xb) at pc=0x00002af3cbe47a27, pid=29834, tid=1170757984
# Java VM: Java HotSpot(TM) 64-Bit Server VM (10.0-b23 mixed mode linux-amd64)
# Problematic frame:
# V [libjvm.so+0x5d8a27]
# If you would like to submit a bug report, please visit:
# http://java.sun.com/webapps/bugreport/crash.jsp
--------------- T H R E A D ---------------
Current thread (0x00002aad7cd06800): JavaThread "Checkpointer" daemon [_thread_in_vm, id=30798, stack(0x0000000045b85000,0x0000000045c86000)]
siginfo:si_signo=SIGSEGV: si_errno=0, si_code=1 (SEGV_MAPERR), si_addr=0x0000000000000010
Registers:
RAX=0x00002aad7c942d80, RBX=0x00002aad7cd06800, RCX=0x00002aad7c943168, RDX=0x00002aad7c942d90
RSP=0x0000000045c84720, RBP=0x0000000045c84730, RSI=0x00002aabf193e230, RDI=0x0000000000000000
R8 =0x00002aad7dcf4380, R9 =0x000000000000784e, R10=0x00002af3cbb8e840, R11=0x0000000045c84810
R12=0x0000000000000000, R13=0x0000000045c84780, R14=0x0000000045c84838, R15=0x00002aad7cd06800
RIP=0x00002af3cbe47a27, EFL=0x0000000000010206, CSGSFS=0x0000000000000033, ERR=0x0000000000000004
TRAPNO=0x000000000000000e
Top of Stack: (sp=0x0000000045c84720)
0x0000000045c84720: 00002aad7cd06800 0000000000000000
0x0000000045c84730: 0000000045c84740 00002af3cbce3a9d
0x0000000045c84740: 0000000045c847b0 00002af3cbb8e896
0x0000000045c84750: 00002aad7dcf4380 00002aad7c942d80
0x0000000045c84760: 00002aad7c942d90 00002aad7c943168
0x0000000045c84770: 00002aad7cd06800 00002aad7cd06800
0x0000000045c84780: 00002aad7cd06800 0000000000000000
0x0000000045c84790: 000000002f7e8112 00002aabf193e1f9
0x0000000045c847a0: 0000000000000000 00002aad5fede569
0x0000000045c847b0: 0000000045c84810 00002aaaab25a0c7
0x0000000045c847c0: 00002aaaab253070 00002aaaab25a08b
0x0000000045c847d0: 0000000045c847d0 00002aad5fede569
0x0000000045c847e0: 0000000045c84838 00002aad5fedef50
0x0000000045c847f0: 00002aad601fedc0 00002aad5fede5b0
0x0000000045c84800: 0000000000000000 0000000045c84840
0x0000000045c84810: 0000000000010001 00002aaaab854744
0x0000000045c84820: 0000000000000000 0000000000000000
0x0000000045c84830: 0000000000000000 0000000000000000
0x0000000045c84840: 00002aad7cd06800 00002aaacd77a138
0x0000000045c84850: 00002aaaf27a8c90 00002aac00000001
0x0000000045c84860: 00002aaa00000000 00002af3cbd73369
0x0000000045c84870: 0000000145c848b0 000000002f7e8112
0x0000000045c84880: 00002aad7cd06800 00002aaaf39de2f0
0x0000000045c84890: 00002aabbee886d0 00002aab35552900
0x0000000045c848a0: 00002aaacd77a3c8 00002aaaf573a448
0x0000000045c848b0: 00002aaaee5aaab8 00002aaacd77a160
0x0000000045c848c0: 00002aab355887f0 00002aaaee643748
0x0000000045c848d0: 00002aaacd77a160 00002aac6a858558
0x0000000045c848e0: 0000000000000000 00002aaacd77a380
0x0000000045c848f0: 00002aad0000005b 0000000000000001
0x0000000045c84900: 0000000000000001 00002aaacd779328
0x0000000045c84910: 00002aabad0b62d8 00002aaaab7589c0
Instructions: (pc=0x00002af3cbe47a27)
0x00002af3cbe47a17: 89 f0 eb ea 90 66 66 66 90 55 48 89 e5 41 54 53
0x00002af3cbe47a27: 0f b7 57 10 48 89 fb 44 8d 62 01 49 63 fc e8 06
Stack: [0x0000000045b85000,0x0000000045c86000], sp=0x0000000045c84720, free space=1021k
Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code)
V [libjvm.so+0x5d8a27]
V [libjvm.so+0x474a9d]
V [libjvm.so+0x31f896]
v ~BufferBlob::Interpreter
Java frames: (J=compiled Java code, j=interpreted, Vv=VM code)
v ~BufferBlob::Interpreter
J com.sleepycat.je.recovery.Checkpointer.flushIN(Lcom/sleepycat/je/dbi/EnvironmentImpl;Lcom/sleepycat/je/dbi/DatabaseImpl;
Lcom/sleepycat/je/log/LogManager;Lcom/sleepycat/je/recovery/Checkpointer$CheckpointReference;Lcom/sleepycat/je/recovery/DirtyINMap;IIZJZLcom/sleepycat/je/recovery/Checkpointer$FlushStats;
Lcom/sleepycat/je/cleaner/LocalUtilizationTracker;Z)V
J com.sleepycat.je.recovery.Checkpointer.flushDirtyNodes(Lcom/sleepycat/je/dbi/EnvironmentImpl;Lcom/sleepycat/je/recovery/DirtyINMap;
Ljava/util/Map;ZJZLcom/sleepycat/je/recovery/Checkpointer$FlushStats;)V
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::StubRoutines (1)
# An unexpected error has been detected by Java Runtime Environment:
# SIGSEGV (0xb) at pc=0x00002b00816f2a27, pid=32743, tid=1162336608
# Java VM: Java HotSpot(TM) 64-Bit Server VM (10.0-b23 mixed mode linux-amd64)
# Problematic frame:
# V [libjvm.so+0x5d8a27]
# If you would like to submit a bug report, please visit:
# http://java.sun.com/webapps/bugreport/crash.jsp
--------------- T H R E A D ---------------
Current thread (0x00002aad7fa1c000): JavaThread "Checkpointer" daemon [_thread_in_vm, id=32646, stack(0x000000004537d000,0x000000004547e000)]
siginfo:si_signo=SIGSEGV: si_errno=0, si_code=1 (SEGV_MAPERR), si_addr=0x0000000000000010
Registers:
RAX=0x00002aad8082f9b0, RBX=0x00002aad7fa1c000, RCX=0x00002aad8082fd98, RDX=0x00002aad8082f9c0
RSP=0x000000004547c5e0, RBP=0x000000004547c5f0, RSI=0x00002aab73edc788, RDI=0x0000000000000000
R8 =0x00002aad7fa08d30, R9 =0x0000000000007f86, R10=0x00002b0081439840, R11=0x000000004547c6d0
R12=0x00002aaca950fcc8, R13=0x000000004547c640, R14=0x000000004547c6f8, R15=0x00002aad7fa1c000
RIP=0x00002b00816f2a27, EFL=0x0000000000010202, CSGSFS=0x0000000000000033, ERR=0x0000000000000004
TRAPNO=0x000000000000000e
Top of Stack: (sp=0x000000004547c5e0)
0x000000004547c5e0: 00002aad7fa1c000 00002aaca950fcc8
0x000000004547c5f0: 000000004547c600 00002b008158ea9d
0x000000004547c600: 000000004547c670 00002b0081439896
0x000000004547c610: 00002aad7fa08d30 00002aad8082f9b0
0x000000004547c620: 00002aad8082f9c0 00002aad8082fd98
0x000000004547c630: 00002aad7fa1c000 00002aad7fa1c000
0x000000004547c640: 00002aad7fa1c000 00002aaca950fcc8
0x000000004547c650: 000000004547c540 00002aab73edc751
0x000000004547c660: 00002aaca950fcc8 00002aad5fef5d49
0x000000004547c670: 000000004547c6d0 00002aaaab25a0c7
0x000000004547c680: 00002aaaab253070 00002aaaab25a08b
0x000000004547c690: 000000004547c690 00002aad5fef5d49
0x000000004547c6a0: 000000004547c6f8 00002aad5fef6730
0x000000004547c6b0: 00002aad600eed48 00002aad5fef5d90
0x000000004547c6c0: 0000000000000000 000000004547c700
0x000000004547c6d0: 0000000000010001 00002aaaaba46ac0
0x000000004547c6e0: 0000000000000000 0000000000000000
0x000000004547c6f0: 0000000000000000 0000000000000000
0x000000004547c700: 0001000100010005 00002aaa00000001
0x000000004547c710: 0010244e00432762 00002aab2ef43ff0
0x000000004547c720: 00002aaaf0635a00 00002aac5694a460
0x000000004547c730: 0000000100000000 00002aad7fa1c000
0x000000004547c740: 00002aabe0162870 00002aaaf0761bf0
0x000000004547c750: 00002aaaf07f20d0 00002aaadd628058
0x000000004547c760: 00002aaadd628ee0 00002aaa00000001
0x000000004547c770: 00002aaaeec996b8 0000000000000000
0x000000004547c780: 00002aab2ecc9890 00002aad00000000
0x000000004547c790: 00002aaadd627af0 00002aac5bc259c8
0x000000004547c7a0: 0000000000000000 00002aaadd628010
0x000000004547c7b0: 0000000000000001 00002aaaee4f8870
0x000000004547c7c0: 00000030f1218c01 00002aaae5222d38
0x000000004547c7d0: 0000000000010001 00002aaaab6cc928
Instructions: (pc=0x00002b00816f2a27)
0x00002b00816f2a17: 89 f0 eb ea 90 66 66 66 90 55 48 89 e5 41 54 53
0x00002b00816f2a27: 0f b7 57 10 48 89 fb 44 8d 62 01 49 63 fc e8 06
Stack: [0x000000004537d000,0x000000004547e000], sp=0x000000004547c5e0, free space=1021k
Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code)
V [libjvm.so+0x5d8a27]
V [libjvm.so+0x474a9d]
V [libjvm.so+0x31f896]
v ~BufferBlob::Interpreter
Java frames: (J=compiled Java code, j=interpreted, Vv=VM code)
v ~BufferBlob::Interpreter
J com.sleepycat.je.recovery.Checkpointer.flushIN(Lcom/sleepycat/je/dbi/EnvironmentImpl;
Lcom/sleepycat/je/dbi/DatabaseImpl;Lcom/sleepycat/je/log/LogManager;
Lcom/sleepycat/je/recovery/Checkpointer$CheckpointReference;Lcom/sleepycat/je/recovery/DirtyINMap;
IIZJZLcom/sleepycat/je/recovery/Checkpointer$FlushStats;Lcom/sleepycat/je/cleaner/LocalUtilizationTracker;Z)V
J com.sleepycat.je.recovery.Checkpointer.flushDirtyNodes(Lcom/sleepycat/je/dbi/EnvironmentImpl;Lcom/sleepycat/je/recovery/DirtyINMap;Ljava/util/Map;ZJZLcom/sleepycat/je/recovery/Checkpointer$FlushStats;)V
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::StubRoutines (1)

Hello,
I know your request is a bit old but I have exactly the same error on a jboss server but no HS_ERR_PID was create...
Java VM: Java HotSpot(TM) 64-Bit Server VM (10.0-b23 mixed mode linux-amd64)
# Problematic frame:
# V [libjvm.so+0x5d8a27]
Do you remember how you solve your problem?
regards
Arnaud

Does the Imovie 6.0.3 update fix the stability issues?

Hi,
Been using Imovie 6.0.2 a fair bit lately, and have had quite a few crashes. I see from this forum that I'm not the only one.
I haven't yet been able to update to the latest version (6.0.3) released last week, and would like some user experience opinions about whether the update has fixed the stability issues. Anybody noticed any improvements or otherwise?
My crashes seem to happen pretty randomly, it could be when you're putting a transition in, or just when you click Play or move the playhead. Any time really. I get the little spinning circle and Imovie is hung. Tried leaving it for ages just in case it was eventually going to return, but it doesn't.
Has the patch fixed it?
cheers,
Ian

Software Update says I have nothing that needs updated. Since I know this isnt true, I went to Downloads and attempted to install both updates--it stopped and said I had to go back to the previous download. After a couple journeys back to nowhere, I gave up.

Connection pool issues with Mysql

Hi,
I have defined sufficient read connections (50) in the toplink configuration, I am finding toplink is not releasing the connections in Mysql, this is when run from Jboss App server.
Is anyone aware of toplink connection pool issues with MySql?
thanks

TopLink always closes connections, I cannot see how this could occur.
Please include your persistence.xml or sessions.xml. Also ensure you are closing your EntityManager or ClientSession, especially if using exclusive connections.
Also include the exception you are getting.
James : http://www.eclipselink.org

K8NGM2-FID Stability Issues

Major Stability Issues. Have yet to install windows successfully. Tried every bios setting imaginal. Tried dual channel and single channel memory cofigurations in every memory slot. When windows tries to install, the system will spontaneously restart, go dark and freeze, or the screen flickers and freezes, basically everything but install windows. I have also tried Suse Linux 9.3 and have experienced the same results. I currently have the Engineering pre production version Bios that other users have experienced having. I have tried to flash/update the bios following the Non-FAT instructions that came with the downloaded V3.1 BIOS zip file and that also has failed. I've read that other posters said they too could not flash the bios due to the fact that it did not recongnize the chip sets. Is there a way to update the bios without using the winflash utility? Is there anything else I should try? RMA? Help, I'm drowning. Thanks.

Anyways, I have had some limited sucess lately. MSI sent me Bios 3.13 which CAN be flashed through DOS. I did a memory test off my Suse 9.3 installation CD to get all my memory timings error free. I did a Western Digital test to make sure the hard drive was properly working. Here is where it got weird. Everytime I went to intall windows, it ask if you agree blah, blah and as soon as I hit F8 to continue it would either lock up or restart itself. I disabled everything in the Bios, went to one stick of Ram, and moved the harddrive to SATA 3. And Finally, I was able to get through the install process and finally get windows to boot up. Once windows is up and running it works great. The problem I am now experiencing is it doesn't always boot up. After the machine posts and is in the process of loading windows it will restart itself. Maybe once out of every 15 startups will windows actual load. Am I unlucky or is the 500 watt PSU I bought still not good enough? Thanks.

Illustrator CS6 Stability Issues- crashing every 5 minutes

Hi All,
I've been having serious stability issues with Illustrator ever since I upgraded from CS5.5 to CS6. It crashes like every 5 minutes, mostly when I use the "nevigator" tool to pan to another area of the artboard. The windows messsage was something like "the program has stopped working".
I am really sick and tired of that and this is seriously affecting my productivity. Furthermore, does Illustrator has any auto recovery function?
Does anybody know what might be wrong? I am using Windows 7.
Grateful for your help.
Best,
James

I keep having the same problem. It would be half as bad if there was at least an auto recovery function.
Also on CS6 / Windows 7.

WRT310N - Connection stability issues

Similar Messages

Maybe you are looking for