Wrt320n + 1Gb/s iomega nas connection problem
I have a linksys wrt320n router and Iomega Home media drive 1GB storage (NAS). The problem after some time, about 30 min router loose internet connection (PPPoE via ADSL modem). NAS support 1Gb/s speed and connected using cat5e cable included with nas. If nas doesn't connected router works fine.
Other clients in network either wireless or 100Mb.
When I connected nas directly to my notebook (100Mb) it works fine.
I am not sure if this a problem with 1Gb/s connection or nas. Anyone experience similar problem? Is it possible to setup only 100Mb connection speed at router?
BTW, I have latest dd-wrt Firmware: DD-WRT v24-sp2 (05/31/10) big
was using mini version before, and original firmware with the same problems.
Thanks,
Eduard
oops, the nas is 1Tb of course.
I reverted to original firmware and lower transmission torrent number of peers. Looks like it works now.
Anyway it's strange that it hangs entire network. After it hangs I connected it to my notebook and watch wireshark.
It asks arp who is 192.168.1.1 constantly, even when I respond to it. And it doesn't ping.
Maybe it's a problem of NAS ethernet adapter. Or low number of files in ulimit. Will try to figure out.
Similar Messages
-
Home Hub disconnects when Iomega NAS connected
I have been struggling to set up an Iomega iconnect on my HH.
Originally, I had an old style white V1 hub. The iconnect connected wirelessly to the hub but would disconnect within a few hours. The broadband connection was not affected.
I also set up the dyndns but could not access the drive over the internet.
I thought that a new V2 hub might solve the problem so obtained one of e-bay and installed it.
It is on Software version 8.1.H.J (Type A).
Again I set up port forwarding.
After about an hour, the phone pings and the broadband drops out. It is out for a very short time then reconnects.
If I disconnect the Iomega the problem disappears.
Any help appreciated.On thing that springs to mind - a faulty Iomega. I've got a WD NAS attached and it doesn't miss a beat - although I don't try and access it over the internet.
-
Iomega FIOS connection problems
Have a G5 macpro desktop without an airport card connected via ethernet to FIOS. Am trying to access an iomega external drive I've connected to FIOS router via ethernet from the macpro, imac (with airport card) and macbook (with airport card) and nothing finds it after software installation on macpro. I seem to be missing something here. Can anyone advice?
Great you have a Mac Pro, sorry, they are never called "G5" which refers to older IBM, not Intel, PowerMacs. 1GB RAM is drastically malnourishing your system. 10.4.8 was also the minimum (10.4.7 was beta, believe me)
Mac OS updates changej/break device support, including LAN setups (just see how Lion once again changed support).
Any requirements like Airport needs later OS? What did you install (and why)?
Routers often have needed new firmware and sometimes new models, so how new/old is the router? make? Apple AirPort Time Capsule Support
I read the comments on these to get more of an idea of Iomega (don't see it used much)
http://www.amazon.com/Iomega-Network-Attached-Storage-34336/dp/B001OC5JLI/
http://www.amazon.com/Iomega-Media-Network-Drive-34763/dp/B004I3VZJK/
Are you using fixed IP?
The bottom line: The Iomega StorCenter Network Hard Drive offers a small footprint and fast-enough performance, but the setup process was a bit frustrating. CNET
Read more: http://reviews.cnet.com/network-storage/iomega-storcenter-network-hard/4505-3382 _7-32576412.html#ixzz1VaKbzfiH
Before installing, do you make a backup clone by habit?
Cloning as a Backup Strategy
Carbon Copy Cloner 3.4.2
I use OS sharing features to share files across all my Macs w/o NAS, though was one feature I looked for as long as all the computers are online. -
Problem downloading iTune Store tracks on NAS - "Connection Timed Out"
I am having a problem downloading iTune Store tracks on NAS - "Connection Timed Out"
I am trying to use the following for my "iTunes Music Location" - \\Nas1\media\Music\iTunes\iTunes Music
However, when I try to purchase music, I receive the following message:
"There was an error downloading your purchased music. The network connection timed out. Make sure your network settings are correct and your connection is active, then try again."
I can purchase songs, the song will begin to download, the appropriate files and folders will be created on the NAS (I can see them), it seems to make two tries to complete the download, then stops, and show me that message.
My network connection (DSL) is fine, and the network is up.
Anything I can do? Is it possible to store iTunes on the NAS, or do I have to set it up to store purchases locally?
Thanks
Dell Demension E510 Windows XP Connected to Infrant ReadyNASbump
-
Nokia 6700 USB cable connectivity problem -fixed-
Ok, got my 6700 today. Everything worked like a charm, until I tried to connect it to my PC using the supplied USB cable. I downloaded and installed the latest Nokia PC suite which supports this phone (7.1.30.9) and connected the phone. Vista was unable to install a driver, and the phone was listed in the device manager as 'unknown usb device'. The phone display reported 'no response from host' after plugging in the usb cable.
I searched online for a solution, and tried the following:
- repaired the install of the Nokia connectivity cable driver: no success.
- deinstalled the nokia pc suite, ran the pc suite cleaner, rebooted and reinstalled the pc suite: no success.
- threw away the unknown usb device in the device manager and plugged the cable back in so that Vista would try to install the driver again: no success.
- tried other USB slots (not behind HUB): no success.
At this point I was so frustrated that I decided to take out the supplied 1gb micro sd card and transfer some data to it using a card reader. When I looked in the root of the sd card, I noticed that there was an executable called pc-suite.exe there, among some other files. I decided to delete those files to see if they were causing the problems, I deleted the following files:
- autorun.inf
- launcher.exe
- pc-suite.exe
- qf
Replaced the micro sd card in the phone, plugged in the usb cable and voila: connection! Everything worked like a charm.
During my online search I noticed I wasn't the only one experiencing connectivity problems with the 6700. Maybe this fix will help other people as well, that's why I decided to post it here. ;-)
PeterThanks Peter, nice job - same problem, your solution is working. Shame on Nokia - i have so many problems with E52, and now with 6700 - why ? Is it so difficult to make a reliable software ? So disappointed ... maybe Apple is the solution - but after 10 years with Nokia why change with Apple ?
-
Files saved to iomega NAS device from Mac not visible to PCs
I'm using my MacBook in a primarily Windows environment at work. We have an Iomega NAS device for our network file sharing.
Some, but not all, of the files I save to the network share from my Mac are not visible to PCs. Am able to see all the files out there saved by the PCs via the Mac, but not all files saved by the Mac are visible by PCs (ie, they show up in Finder/Mac but not in Explorer/PC).
Details:
- Mac OS X 10.6.2
- iomega StorCenter ix2 Network Storage Device (NAS)
- Netgear Router (details unknown)
All other network works fine from the Mac -- can see shared PCs, can use network attached printer, access the Internet, see all the shared folders on the NAS device.
Happens with all types of files (MS Office documents, JPGs, GIFs, PDFs), but not for every documents. Probably 3 out of 4 documents saved to NAS device from Mac are visible to PCs on the network, and 1 out of 4 is not visible.
Any ideas? Thanks.OS X 10.4.8 update has not altered the behavior of this bug. The Office 2004 11.30 update seems to have caused the problem to happen less frequently. I would say it now happens half as frequently.
-
WLC 2504 Connectivity Problems
This is a tricky one.
I installed a 2504 WLC with three AP's. Two SSID’s were configured, one with WPA2/AES-TIKIP and the other with Web Auth.
After installation, customers could connect to WLAN without problem and .
The problem that is occurring is that since the beginning of week, customers PDA's, cell phones and iPad and cannot access Internet with any of the two WLAN but clients who used laptop have no connection problems. Also the DHCP Server is assigning IP's correctly.
This problem also occurs with test SSID I created which is Open Auth. I see associated Cell phones and IPAD to the WLC but none of these answers ping from the WLC.
This is a WLC 2504 with IOS 7.4.100.Hello everyone!
Today I did a test with my Cell phone Samsung Note 2 and I have the same conectivity problem.
I have installed the APK ipconfig from the Play Store for Android in my cell phone and y see that I getting IP Address, Mask and Gateway.
This is what I´ve got from the APK:
IP ADDRESS 192.168.8.181
MASK: 255.255.255.0
GATEWAY: 192.168.8.2
DHCP SERVER: 192.168.8.16
DNS1: 192.168.6.16
DNS2: 192.168.2.16
I have connected my laptop to the WLAN with no issue and I´m getting this:
The IP address of the DHCP Server is 192.168.8.16 and 192.168.6.16 and is a Microsoft Server.
I´ve created a test WLAN with OPEN AUTH but the problem remains.
Here is the OUTPUT you requested:
show wlan 1
WLAN Identifier.................................. 1
Profile Name..................................... APS-PT-01
Network Name (SSID).............................. APS-PT-01
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 16
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... APS-Admin-WLC-01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >show w?
wgb wlan wps
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... APS-Visitas-PT
Network Name (SSID).............................. APS-Visitas-PT
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... APS-Admin-WLC-01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Enabled
IPv4 ACL........................................ Unconfigured
IPv6 ACL........................................ Unconfigured
Web-Auth Flex ACL............................... Unconfigured
Web Authentication server precedence:
1............................................... local
2............................................... radius
3............................................... ldap
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional but inactive (WPA2 not configured)
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
(Cisco Controller) >
(Cisco Controller) >show wlan 3
WLAN Identifier.................................. 3
Profile Name..................................... Prueba
Network Name (SSID).............................. Prueba
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... APS-Admin-WLC-01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Enabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Disabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Enabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Disabled
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled -
Network connectivity problems on a Lenovo ThinkPad T60p
Greetings,
I am having connectivity problems with my Lenovo Thinkpad T60p. And I would really appreciate some help.
I know both ethernet connectivity and WiFi connectivity work because if I boot with different OS, I can access the network. So this is not a hardware problem. It is a software problem...
I have uninstalled the existing Ethernet and Network drivers by removing them from:
1. The Control Pannel -> Add/Remove programs
2. The Control Pannel -> System -> Hardware -> Device Manager
3. The directory level in C:/devices/win/ethernet etc.
I have downloaded the drivers again. Re-installed. Same issues.
I see both card in The Control Pannel -> System -> Hardware -> Device Manager . The Wireless card is
ok. The Ethernet card shows a yellow alert sign.
At boot time I get a message indicating a service cannot be started but the the system logs show no related errors.
As far as wireless, the network card appears, in the Network tab of the Windows Task Manager, but the status
is "Non Operational". I can see the networks around me, but I cannot connect, even when there is no encryption. This might be the first one to fix, since it will give me mobility even if I sacrifice speed and open myself to hacking.
As far as ethernet, I see the network card DOES NOT appear in the Network tab of the Windows Task Manager, but as I mentionned before, I know that there is a problem with that.
I hope someone can help me with this. The only other options I have are re-install the OS, install another one, or take the machine in for service, something I am reluctant to do, as I claim to be an IT professional for 30 years and that I can fix other people´s machines...
Thank you.
Regards,
Jean-Pierre
Solved!
Go to Solution.Hello,
The ThinkPad T60p (2007-8EU) looks like a decently-configured ThinkPad:
2700(2.33GHz), 1GB RAM, 100GB 7200rpm HD, 14.1in 1400x1050 LCD, 256MB ATI FireGL V5200, CDRW/DVDRW, Intel 802.11abg wireless, Cingular WWAN, Bluetooth/Modem, 1Gb Ether, UltraNav, Sec Chip, FPR, 9c Li-Ion batt, WinXP Pro
The TPM driver is used to communicate with the T60p's integrated security module. You can download the latest version of the device driver from here on Lenovo's support site. Although listed as being for Windows 2000, XP and Vista, I believe it works just fine under Microsoft Windows 7 as well.
My working hypothesis is that removal of the third-party firewall damaged the network settings in Windows. That's a problem that periodically comes up with the various security software packages from different vendors.
What I would suggest at this point is the following:
Check with the third-party firewall vendor to see if they offer a manual uninstallation program to uninstall the software. Download that and run it per their instructions, booting into Safe Mode, if necessary.
When that process is complete, try resetting the network stack by issuing a "NETSH INT IP RESET RESETLOG.TXT" command per Microsoft Knowledgebase Article # 299357 "How to reset Internet Protocol (TCP/IP)". The article is applicable to Microsoft Windows XP SP3 and later.
At this point, you should be free of any services, device drivers, NDIS intermediate drivers, WinSock LSPs or other objects from the third-party firewall software, and all network connections should be restored to their default values.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество -
Timeouts and connection problems after 5.1(2) upgrade
AIM/chat and some other programs are having timeout/connection problems after upgrade to 5.1(2). I am using S241 also. The connection problems stopped when the IPS was set to bypass. Rebuilt IPS and left sigs at default settings and problem is still happening. I am not seeing any of the IPs that are having the problem in the Event Viewer or on the Events in the IDM.
Any known issues with the 5.1(2) that would cause this type of problem?I don't know specifically, but I did notice that 5.1(3) was released today.
-
Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.
Hello Sue,
I have an iPad 3, iPad Mini and iPhone 5S and they are all sluggish on capitalisation using shift keys. I hope that Apple will solve the problem because it is driving me crazy.
I find using a Microsoft Surface and Windows 8 phone, which I also have, work as well as all the ios devices before the ios 7 upgrade.
It has something to do with the length of time that you need to hold the shift key down. The shift key needs to be held longer than the letter key for the capitalisation to work. For some reason, this is a major change in the way we have learnt to touch type on computers. I am having to relearn how to type!
Michael -
RFC Receiver adpater Connection problem , Help us to solve ?
Hi Friends ,
Our scenarilo is Mail to RFC. It was running fine. In RFC Receiver adapter i have given <b>Maximium connection property to 1</b> .
While multiple set data passed to rfc will connection problem will come ?
Most data not uploaded . I am getting the following error.
<b> If i set max connection to 5 . It is 5 times or more than that it is pusing the data .</b>
i am getting the following error <b>while i set the Max connection to 1 .</b> . <b>Any other place i need to change configuration ?</b>
<i><b> - Error: 2007-09-24 10:51:22 GMT-05:30: Message processed for interface YRFC_EXT_WARR: com.sap.aii.af.rfc.afcommunication.RfcAFWException: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException: resource error: could not get a client from JCO.Pool: com.sap.mw.jco.JCO$Exception: (106) JCO_ERROR_RESOURCE: Connection pool RfcClient[CC_EXTE_WAREN_2W_RFC_RECEIVER]e7fa21f86ec535e883636c0beffc0f0c is exhausted. The current pool size limit (max connections) is 1 connections.</b></i>
Please give the description . I have referred many likns . Help us to solve this problem .
Regards.,
V.Rangarajan<b></b>
Message was edited by:
ranga rajanHi,
Have a look at this.This will help you.
1.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f3f93ee7-0c01-0010-2593-d7c28b5377c2
2. https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/3103eb90-0201-0010-71af-be6f4a6f61d1
Regards,
Akshay Jamgaonkar.
Reward points if find useful.
Message was edited by:
Akshay Jamgaonkar -
Unending connectivity problems -- and Desktop Help...
I'm wasting so much time on connectivity problems that it's positively wearying. Prior to the installation of BT Infinity here in April, I had a low quality broadband service because of the length of the line from the exchange: if I could get a download speed of 1.2Mbps and an upload of a quarter of that, I was doing well.
BT advised that thanks to fibre optic, my Internet should run much faster. So we had Infinity installed. I'm registered with Speedtest.net so am able to see my performance record.
The average download speed is now aroun d 6Mbps and the average upload, more than that at 7Mbps. How an upload speed can consistently be faster than a download escapes me.
But I'm not familiar with the ways of Internet connectivity and try as a I might, can't get my head around it.
This desktop computer runs Vista OS. Vista was **bleep** when it came out and is renowned for its botched handling of Internet connections. So I'm not blaming BT for the literally unending connectivity problems that are occurring now, with line drops, speeds slowing to a crawl, and no guarantee that any connection will last. But it would be good to actually use BT software to help fathom out what's going wrong here, and today's typical morning which looks like this:
1) Boot up computer. Automatic connection to hub via Netgear USB wireless adapter. Hub is on ground floor of this 3-storey property but signal strength from hub is excellent, as confirmed by inSSIDer monitoring, currently showing 54 with no other networks anywhere near that figure.
2) Perhaps 5 minutes after connection established, it's then lost. 'Local Only' is displayed. This is, apparently, a known Vista problem. But Microsoft has issued a fix for it. I know this, because it took 100 hours of ploughin g the Net to find out that MS had finally admitted to one more Vista screw-up. I've used the Microsoft router "fix it" before and it didn't work ("failed to process") so uninstalled it and have DL'd it again now and run it. This time it says it has fixed everything.
3) Computer is re-booted to make the fix effective. Computer connects to Internet. Speedtest.net check yet again confirms that upload speed is faster than download speed.
4) Connection dies. So much for Microsoft Fix It.
5) Windows diagnostics reports that it can re-set the IP profile (or something.) I click yes. The re-set goes through. Connectivity is restored. 10 minutes later, connectivity is lost. Just a red X in the tray. No connection of any kind, not even that daft 'Local Connection' only alert.
6) Reboot. Yet again. BT Desktop Help was installed here and ran OK when we were using our Netgear DSG34 router. But since the change to the BT Hub, the BT program has never run at all. So-oo. . . It has been uninstalled. And then re-DL'd and re-installed. And though the installation has been completed, clicking on 'launch' has failed to launch anything. But anyway. An hour ago, in one of the brief periods today when the Internet connection was holding up, I Revo-ed out the earlier install, DL'd BT desktop Help and re-installed it. . . and I'm still at the same stage as always, with a Firefox browser page that's open and completely blank and has been for the past 30 minutes. The URL is:
file:///C:/Program%20Files/BT%20Broadband%20Desktop%20Help/btbb/Start.html
Repeated page re-loading gets nowhere. Malwarebytes PRO is turned OFF to prevent any possibility of blocking and the antivirus is termporaily SUSPENDED. This PC runs on Windows standard firewall but even turning that OFF doesn't get the page to load. Copying the address into Internet Explorer in case there's a Firefox problem merely results in Firefox being opened and the same blank page running there.
7) After all that. . . Connection lost yet again and this time, Windows cannot connect at all. It reports that the "wireless network security key is not correct". I happen to know that it is, because this is maybe the 20th time it has reported this in the past 10 days and every time I have to key in the "correct" key all over again. . . at which point Windows still says it isn't correct and cannot repair.
Turning off the computer completely, unplugging from the wall, holding in the power switch for a full minute to clear the circuits, traipsing up and dowen three flights of stairs to turn off the hub, then wait, then turn the power back onm again. . . Ah, wot fun times I'm having here with my particular versioin of Infinity (as in, an infinity of connectivcity problems.)
Summary: I seem to be being simultaneously hit with one issue after another.
I'm bewildered as to why ever since Infinity was installed here, my upload speed is generally faster than my download speed. I'm not happy with endless Internet connection failures though am thinking that Vista is playing a large part here with its "wrong security key" and unending 'Local Only / Limited Connection' failures. I do miss my Netgear router and the ability to access a fantastic help menu and re-boot directly from the desktop without having to keep going up and down three flights of sdtairs to do so (I haven't been able to find out how toe access the BT Hub remotely.)
Above all though: I'm really tired of repeatedly trying to run freshly downloaded and installed BT Desktop Help software but getting no further than a blank page because the program has stalled.
If anyone has any advice / suggestions, other than to buy a carrier pigeon, that'd be much appreciated.
Thanks.Thanks again to John and gg30340. Here's an update:
1) BT Desktop Help removed completely from this computer. The uninstaller itself mopped up everything, which surprised me. But anyway.
2) Bt Home Hub manager set up and working. Had to input serial number and create new password. All of this sounds fairly easy and would be if one had the device near the desk. But the idiots who built this property shoved the BT master socket inside the garage next to the door. Our two home computers are on the third floor. To ensure the wireless signal strength is OK, the Hub and Infinity module/device/whatever it's called are on a high shelf. It's a major job to even reach the darn things, never mind read the labels seeing as how the BT Infinity engineer was good enough to tidy up the cabling and make a very tight connection to the wall socket.
3) I had hoped to be able to back up the Hub's settings, seeing as the software provides for Advanced Settings / System / Backup. But not on mine (Hub 3.0). All that System allows is choosing which internet clock to define the accurate time. Everything else in System is just a pattern of short lines as if trying to indicate that there's some text there but it's invisible.This is now my second encounter with BT software which, for whatever reason, isn't functioning as it should on this PC.
4) Hub reset to factory fresh, according to BT guide.
5) Reset appears to have achieved nothing apart from requiring the password to be popped in again. After reset, it wasn't even possible to connect to the hub manager. Internet connectivity was eventually established for all of 30 seconds and then, gone.
6) Computer was shut down and then booted anew. Internet connectivity is still. . . dreadful. One minute everything's fine and then, literally,. the next minute a webpage won't load. Even opening the Hub Manager has taken three attempts, i.e., disconnecting from the Internet, re-connecting, failing, and trying twice more until success. Yet all the time these failures are occurring, the tray icon is showing a steady, unwavering green icon for Local and Internet access -- despite the fact, there manifestly isn't any.
7) Speedtest. net tests are actually showing upload and download 'trajectories' going slower and slower and finally halting at some point on the arc, then after a period of up to 30 seconds, suddenly becoming animated again. Speed test results with broadband speed checker UK and Think Broadband's checker are so at variance with one another, and with Speedtest, net, that it seems all three are using different technologies in pursuit of the same thing. Either way, upload speeds continue to be much, much faster than download speeds, a state of affairs I certainly have never encountered before.
8) Speedtest net tests taken in the past 10 minutes, with one test following on from its predecessor, begin at 8.24 down/8.88 up, followed by 5.24 down / 6.40 up, followed by a mind-numbingly lonnnnng 0.62 down / 8.70 up -- in other words, a continuous yo-yoin g of Internet connectivity to the pooint that it actually might as well not even be here (I've had to make five attempts just to get on to this forum. . .)
9) BT Speedtest will necessitate disconnection of everything downstairs and all boxes being lugged up here. This is actually going to require uncoililng tied-off cabling and hanging off a stepladder to do so -- though I surely can't be the only person in Britain who doesn't have a nice, handy BT master socket in their study or lounge. That said though: until we switched to Infinity, we *never* experienced these kinds of horrendous connectivity problems and never had need to unplug the Netgear router downstairs and bring it upstairs to connect directly to tjhe desktop PC so BT's own test could be run.
I'll just have to get to work dismantling stuff tomorrow. However, I have to say that after a factory re-set which has changed nothing at all, I'm beginning to think there's a problem with the BT line itself (hence why I'm happy to follow the advice here, though less than happy at the prospect of the messing about involved.)
Thanks, you two, for your patient help, and also for clarifying the situation re the three signal paths being shown on inSSIDer. At least I know that's usual now! And now, hopefully, when I press 'Post', I won't be faced with an endlessly spinning Firefox circle culminating in what may well be, or seem to be, the 57,938th time today of seeing "Page Not Found". . . -
PHP and MySQL Connection problem
I am trying to make a PHP MySQL on a remote server connection in Dreamwesaver CS3.
When I enter the information (host, user, password, etc.) and hit TEST, I get the following error message.
"Access Denied. The file may not exist, or there could be a permission problem. Make sure you have proper authorization on the server and the server is properly configured."
I know the user, password, etc. work, as I can access the MySQL database with other software.
I checked with my host and they say there are no permission problems on their end.
I have checked the settings on the Test Server page in Site Setup and everything looks correct and works there.
I have not seen this particular problem described in other forum postings (although there are a LOT of postings on this topic!).
Any help would be appreciated.I thought my testing server was the remote server and is always on as far as I know. I don't know how to turn it on or off.
Is there some other testing server that I should be aware of?
Frank
Date: Wed, 3 Jun 2009 15:43:02 -0600
From: [email protected]
To: [email protected]
Subject: PHP and MySQL Connection problem
I know you are using remote, but is your testing server on? if not turn that on and see if that does it. it just happened to me working on remote server and could not get mysql conn to work, until I turn on my testing (developer server), then I was able to connect to mysql and the tables that I created in phpmyadmin remotly was downloaded.
> -
my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/ht4097
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work. -
Hi
I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?
I have tried reseting the network settings and forgetting my wireless connection and re-connecting to it. I even backed up my phone on itunes and restored it, factory reseted it. Nothing seems to work.
Also after my upgrade to ios 8.1 my personal hotspot option under cellular data has disappeared.
Would you please help me out? I would really appreciate it.Hi..
Restart your router then restart the iPhone to test.
If that doesn't help, try this support article > iOS: Troubleshooting Wi-Fi networks and connections
Maybe you are looking for
-
Best Battery Health not working in Windows 7 after Windows 8 installation
Hello everybody, I'm having an annoying problem with my G475. It came with Windows 7 installed, and the option "Best Battery Health" was working fine. Then I upgraded to Windows 8 (fresh install) and installed the Energy Management drivers. Since "Be
-
Is there any way to sync POP mail between iOS and Mac devices via the cloud?
The title says it all. I have Comcast email and would like to keep three devices in sync with email like I do with calendars and contacts. I use an iPad, iPhone, and a Mac Mini and am having a hard time configuring the three to stay in sync. It se
-
Billing document creation problem
Hi All, i am not able create a billing document (vf01)with reference to a delivery order.It is giving error as billing document can not be saved due to error in account determination.can u please tell me how can i solve this problem.
-
When downloading from a Sony minidisc video camera, the picture is downloading but without sound. Previously, it had downloaded successfully both sound and picture. I have subsequently upgraded to Lion X (10.7.4). Is there some problem with the up
-
ITunes asking for obsolete computer authorizations to play songs
I had to buy a new computer recently and I transferred my iTunes library over to it. But now certain songs on my iTunes are asking me to authorize my computer with an old Apple ID name..a name/email address that doesn't exits anymore and hasn't been