WRT400N wireless router industrial network static IP

I have two small industrial networks all with static IP addresses. One network uses IP 192.168.83.xxx and the other uses 192.168.84.xxx. I plan to add two more of 192.168.82.xxx and 192.168.81.xxx where xxx is the last number of the devices. I had a subnet mask of 255.255.255.0 for each. I wanted to use the abobe wireless router to connect by LAN each of the networks and then use wireless from my PC to connect to them. I am able to set the static address of the router to work with any one network but not all at the same time. There is no internet or intranet available and I have tried used the internet port to connect without success. Any sugestions? I think the problem is with my subnet mask but the router does not let me choose 255.255.0.0 as a subnet which is what I think I need to do this.

Well its not possible to change the Subnet Mask of your Router... As all the Routers works on a Class C Subnet Mask... You can try DD-WRT Firmware and check if they have the open to make your Router work with a Different Subnet..

Similar Messages

Having trouble connecting Wireless Router to Network

Hey everyone, I ordered two Encore ENHWI-2AN3 wireless routers and am having trouble configuring the one I want to use as the wireless access point (other one will be used as a repeater.)
I followed the advice here
http://forums.verizon.com/t5/FiOS-Internet/Wireless-Router-Doesn-t-Work-After-35ft/m-p/206716/highli...
I disabled DHCP, and set a new IP on the local network. I disabled WiFi on the verizon router as well. When I run an ethernet cable between the two using LAN ports, and try to use WiFi I get a signal, but it doesn't go load.
I'm assuming I need to tweak something in the "internet" section of the Encore router, the main options are Dynamic or Static IP, PPPoE, PPTP and L2TP.
To clarify, I am not looking to replace the Verizon router, only use the Encore router for Wifi

kimdpb wrote:
Wireless is working for all the other devices
Using a Cisco router with Network Magic Interface....it doesn't see the Mac Book but the Mac sees the network.
Can you see the network in the Mac's wireless network list?

Want to add second wireless router to network

I have a Actiontec MI424WR and would like to add a second wireless router, a Linksys Cisco E2000 which has N capabilities. What is the best way to add this second router so that they both work as wireless routers? Thank you for your help.

If I'm not mistaken, they can leave the SSID on both access points to be the same. You just don't want them to run on the same channel. The devices with either setup see an Access Point by it's MAC Address. It should have no problem roaming onto another Access point if one starts to get too weak for the device's liking. Even with separate SSIDs, that will still happen.
What the above poster means by setting up the Linksys as an Access Point is the following:
1: Disable DHCP on the Linksys
2: Disable the Firewall, UPnP support in the Linksys
3: Configure BOTH the ActionTec and Linksys to operate on WPA2 Security (The Linksys E2000 is a Wireless N router. Wireless N requires WPA2 to work to it's potential).
4: Set both the ActionTec and Linksys to separate channels, either 1, 6, or 11. It's best to keep them off each other's ranges due to the distance between the two APs. The Linksys should only be set to use 20Mhz wide channels for Wireless N. DO NOT OPERATE IT ON AUTO/40MHZ!
5: Connect the Linksys to the ActionTec by plugging the Linksys into the network using one of the LAN Ports. Do not use the Internet port on the Linksys!
Just keep in mind, if you do set up the Linksys to run on the same SSID as the ActionTec, the security settings (Key, Encryption type, MAC filtering) must be identical. If you go down the separate SSID route as mentioned above, you're free to keep the security settings separate. Just keep in mind my pointer with WPA2, though.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Need to backup Time Capsule, (3rd Gen) 7.6.1 used as wireless router and network drive

I use Time Capsule, 802.11n (3rd Gen) 7.6.1 (1Tb) as a wireless router and a network drive. I do not use Time Machine at all. How do I create a backup of the files housed on the Time Capsule to an external drive?
Also, why does the use of Time Capsule as a network drive seem to be such an usual configuration? The configuration makes sense to me, aside from the inability to automatically back up the Time Capsule itself to a cloud or other drive, which, to me, is what really makes no sense at all. Is there something else I should be using? I'm not too familiar with the wisest way to set up a home network. I just know I like to wirelessly have access to my files from multiple computers within my household as opposed to saving files on any one computer locally.
Thanks for your assistance and advise!
erinblythe

You could connect a USB hard-drive to the USB port on the TimeCapsule and Enable Disk Sharing on both the TC's Built in Drive as well as the USB connected one.
Then these drives can be mounted using finder and files copied between them as needed.
The main advantage of time-machine is - automation(like you mentioned) + to be able to go back in time - i.e. ability to restore files from a certain date/time. Multiple versions are available for restore.
Also in Mountain Lion - You can restore your mac from a time machine backup very easily - it is one of the options when you boot to the Recovery Partition (ditto when you boot ML from DVD/USB)
Hope this helps.

Will a desktop connected to a wireless router via network cable be able to use a wireless printer?

My computer is a Dell runing XP home edition. This computer is connected via a network cable to the wireless router.
My deskjet 4580 printer is connected to the wireless router network and printing and scanning via wireless network with a laptop that is connected to the network wireless.
Now I want to print and scan using the desktop computer also. Should I install the wireless driver for the printer? Do I need to connect the printer with USB cable with my desktop computer?
Please help. I do not want to disturb the laptop that can print and scan wirelessly with the printer.
Thanks.

if the printer is connected to the router wired, then the router is the hub, so you should just need to install the driver for the printer in the machine that is not working.
If you install the full feature driver to the printer on the computer you want to print via wired to the router to the printer that should work. Run this too:
HP Print Diagnostic Utility
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&lang=en&softwareitem=mp-91788-1
Signature:
I currently work on behalf of HP for numerous support departments. The opinions expressed above are the personal opinions of myself, not of HP. There is no guarantee that the opinions expressed are 100% correct.

Time Capsule + Belkin Wireless router, same network to separate slower devi

Alright ladies and gents here's what I got.
I have a Time Capsule and a Belkin wireless n+ router. I want to use my Time Capsule to connect all my wireless n devices using the 5,0GHz band and use the Belkin router using the 2.4GHz band to connect the g devices thus simulating a simultaneous dual-band Wi-Fi, of course all in the same network. I want to be able to see the TC disk from the "slower" devices.
Is this possible?
Any ideas on how to configure?

+I want to be able to see the TC disk from the "slower" devices.+
+Is this possible?+ Yes
+Any ideas on how to configure?+
We're going to need know how you have things configured now. Is the Belkin router the "main" router at this time?
+I want to use my Time Capsule to connect all my wireless n devices using the 5,0GHz band and use the Belkin router using the 2.4GHz band to connect the g devices thus simulating a simultaneous dual-band Wi-Fi, of course all in the same network+
Using the same wireless network name for both the 2.4 GHz and 5 GHz bands, as is done on the Apple "dual band" routers, there will be no guarantee that faster computers will connect to the 5 GHz network if they happen to see a stronger signal from the 2.4 GHz network...which is likely as 5 GHz signals are absorbed much more quickly than 2.4 GHz signals.
Your computer will always connect to the stronger signal...not necessarily the faster signal first, unless you tell it otherwise.
Message was edited by: Bob Timmons

Wrt400n wireless router resetting at random

My router will randomly reset for no apparent reason while using the internet. If i am streaming a movie from my server or anythin for taht matter it will freeze up and when i look at the connection display at the bottom of the computer i will see i am no logner connected to my local network. After a couple of minutes i iwll see my computer reconnecting and then all i well. It just randomly resets every so often for no reason that i am aware of. It happens with both wireless and wired connections. I can make it resolve quicker by just unplugging the power and rebooting it myslf but it does it on its on if given a minute or two. Thisi s rather annoying and i would appreciate any help figuring out why its happening.

Open the setup page of the router by typing 192.168.1.1 in the address bar...Under setup tab,change the MTU size to 1350 and click on save settings.Under the Wireless tab,click on Advance Wireless Settings tab...Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2307 Click on Save Settings...
Now,power cycle the router for 1 minute and check...

Wireless router and beige G3 question (OS 8.6 or 9?)

I've purchased a Netgear 54 mbps wireless router to network my Macs. For now, the G4 tower and the 266 beige G3 are going to be connected through two of the hardwired ports until I can get an Airport card for the G4. The G4 is running Panther 10.3.9 and connects via built-in Ethernet. The beige is running OS 8.6 and connects via an Ethernet PCI card (the built-in port is dead). The third machine is a laptop with an Airport card.
Should I upgrade the G3 to 9.2.2 before I set up the network or can I go ahead with things as they are now?
G3 beige (OS 8.6), G4 Sawtooth (OS 10.3.9), TiBook (OS 9.2.2 and OS 10), G5 Mac OS 8.6 or Earlier

don't like being different, but on a 266MHz G3 with maybe limited memory, OS8.6 will still fly, OS9.2 starts to slow down on certain tasks.
IMHO, OS8.6 was as good as it ever got for a stable and secure Mac OS.
But you may find the update to OS9, with IE v5 and QuickTime v5 may just be worth the slowdown. Depends what you're going to use it for, I removed OS9 on my old iMac 233MHz and put OS8.6 back on. It does everything I want it to, fast.

Wireless router and beige G3 question

I've purchased a Netgear 54 mbps wireless router to network my Macs. For now, the G4 tower and the 266 beige G3 are going to be connected through two of the hardwired ports until I can get an Airport card for the G4. The G4 is running Panther 10.3.9 and connects via built-in Ethernet. The beige is running OS 8.6 and connects via an Ethernet PCI card (the built-in port is dead). The third machine is a laptop with an Airport card.
Should I upgrade the G3 to 9.2.2 before I set up the network or can I go ahead with things as they are now?
G3 beige (OS 8.6), G4 Sawtooth (OS 10.3.9), TiBook (OS 9.2.2 and OS 10), G5 Mac OS 8.6 or Earlier

The beige is running OS 8.6
Should I upgrade the G3 to 9.2.2 before I set up the
network or can I go ahead with things as they are
now?
You should be able to go ahead now and see how it works, the OS 8.6 G3 should be able to connect to the internet, mount any shared drives from the other network Macs, and print to any shared printers (may require OS 8.6 drivers on the G3) on the other Macs. This would be useful for backing up the G3 harddrive to another Mac's larger HD and then burning to CD/DVD media, if your G3 has only the stock CD-ROM drive. If you find that something doesn't meet your needs, then you can upgrade the G3 to OS 9 later, but it should operate on the network just fine with 8.6, although I haven't used OS 8 myself in quite a while, so I could be totally wrong.
From memory, I think I had at one time networked a Performa 5200 with 8.1 and my G3 running 10.2, so I'm not sure if there are any major differences that might cause difficulties between 8.6 and 10.3.
What is your planned usage of the G3 on the network?

Add Wireless N Router To Network With An Actiontec Router

Hi everyone, I know this wireless N thing is being beaten to death but I just really need to be pointed in the right direction. I recently built a HTPC setup with a SiliconDust HD Homerun network tuner so I could share three tuners with computers on my network. I've got two PCs wired to the network right now which share them fine. But the problem I'm running into is when I try to set up my laptop to watch something wirelessly, usually a game in HD. The signal is very weak and I constantly lose the tuners because of that, not to mention the picture is very choppy. I saw on a Microsoft Windows Media Center site that they don't recommend streaming HD TV feeds over anything other than a wireless N connection. I currently have the standard Actiontec router that came with FiOS, and it doesn't the N band. Now, that router accesses the internet signal through a coax so I know I can't get rid of it, but I've seen mentioned in a couple of places that you can just add a wireless N router into the network and turn off the wireless on the Actiontec router. This is the router I was thinking of getting:
http://www.bestbuy.com/site/Cisco+Linksys+-+E1200+Wireless-N+Router+with+4-Port+Ethernet+Switch/2225...
My current network setup is like this: Actiontec router upstairs which carries internet to -> a gigabit switch connected to -> computer, tuners, and printer upstairs, with a line run to -> another gigabit switch downstairs which connects to -> a computer, and an XBox.
So a couple of questions about this:
- Where would this go on the network? Would it go after the router and before the switches, like I run the internet into the new router then out to the switch, or can I just add it to one of the switches?
- Will I need to do any sort of port forwarding or anything, or assiging of IP addresses?
- Anything else I should know or might run into?
I love my FiOS service so hopefully this will help me get even more out of it!
Solved!
Go to Solution.

I wanted to upgrade to an N protocol wireless router but since Verizon doesn’t offer the option, I purchased a Netgear N600. Unfortunately, after it arrived, I discovered that it didn’t have a coax connection as did the Verizon Actiontec. I then set out to find out how to daisy chain the routers to leave the Actiontec connected to the coax and connect the two routers via Ethernet cable. To my good fortune, during the time I spent on the phone with Netgear, I learned my way around their router interface and with the help of a co-worker that actually has a solid understanding of router/network configuration, I finally got everything working correctly – my port forwarding for RDC login worked, I could connect devices to either router and everything could once again see each other (e.g. PC, printer via Ethernet, Blu-ray player for Netflix, receiver for streaming Windows Media Player). Hopefully, this post will help you get up and running quickly and avoid the several hours I spent groping in the dark for the correct configuration.
Login to Verizon Actiontec router (type 192.168.1.1 into browser address bar).
No configuration changes are necessary on the Actiontec, you just need to identify an open IP address range in My Network section (I chose 192.168.1.50). This will be used as your static IP address of the Netgear router LAN settings.
Connect you PC via Ethernet cable directly into an Ethernet port (not WAN/Internet) on the Netgear router. No other connections are needed at this point.
Note: Do not use the Netgear wizard CD to setup the router. It will not take you through the necessary steps as you’re not setting it up as a router.
Login to the Netgear router (type routerlogin.net into the browser address bar) using the default login of “admin” and password “password”. Depending on your firmware version, your interface may vary but hopefully you’ll be able to find the same configuration options in either but perhaps not in the same order or placement. For subsequent logins after the router is active, you may need to type the Netgear IP address (e.g. 192.168.1.50) as routerlogin.net may open a search.
At the top of the Netgear genie, click on the Advanced tab.
On the left side, expand Setup, then select Internet Setup.
Select “Get dynamically from ISP”, under Internet IP Address.
Under Domain Name Server (DNS) Address, select “Use These DNS Servers”, and enter the IP Address of your Actiontec router (e.g. 192.168.1.1) in the Primary DNS” field.
Next go down a few options within Setup to Wireless Setup.
In the Wireless Network 2.4GHz section, click Enable SSID broadcast.
Enter a meaningful name in “Name (SSID)” as this is what will be displayed for your wireless connection.
For Channel, select Auto.
For Mode, select “Up to 300 Mbps”.
Security Options, recommend WPK2-PSK[AES] for longer/stronger password options.
Set the password of your choice.
Repeat the same process for Wireless Network 5GHz, except vary the name slightly so you’ll be able to distinguish which band you’ll connect to. You can optionally use the same or different password as your 2.4GHz. The only exception is you’ll have to select a Channel of your choice.
Next go down a couple more options within Setup to the LAN Setup.
In the LAN TCP/IP Setup section, enter the IP Address you chose in step 2 (e.g. 192.168.1.50).
Enter the IP Subnet Mask 255.255.255.0
Leave the block for “Use Router as DHCP Server” blank as your IP assignment will be handled by your Actiontec router.
You’re now finished with the configuration and you can connect the Actiontec router to the Netgear router using an Ethernet cable using the LAN ports (Note: do not connect the two routers using the WAN/Internet ports on either). You may connect your devices (PC, printers, A/V devices, etc.) to either router. If you have devices that are gigabit capable, you’ll want to connect them to the Netgear router to take advantage of the higher speed.
To avoid any possible interference between the 2.4GHz range of the two routers, you can optionally turn off the Actiontec wireless capability by logging into the Actiontec router admin (described above), go to the My Router tab, and there should be an option for “Change Wireless Settings” in the Quick Links section. Option 1 allows you to turn On/Off the wireless portion of the router.

How to connect a E1200 wireless router to a machine tool network for wireless communications

Hello all, I am new to the forum, hope someone can help me out. I am wanting to connect my E1200 wireless router to a machine tool in our factory that has programmable controllers and is connected to the machine components via ethernet connections. This is so we can troubleshoot the machine without having a wired laptop. We have several ethernet switches on the machine and a range of IP addresses say from 192.16.1.1 through 192.16.1.150, and 192.16.17.1 through 192.16.17.150, all of the addresses are not used but random addresses in the range. I would like to be able to connect my E1200 to either one of the networks without having to make a change in the router setup. I can make it work on either network but when I switch my cable to the other network it has to be reconfigured. I am currently connecting my data cable to a ethernet port on the router and changing my router address from 192.168.1.1 to 192.16.1.1 and selecting a range of 150 so it will assign numbers as needed. This works great until I change to the other network and I have to change my router address to 192.16.17.1, I know this can be done on some routers because the technicians from the machine builder use them when working on the machines. thanks

On the basic setup tab make the changes shown below:
This basically make the router disappear off the existing networks and turns it into a wireless AP.
Then when you set your laptop's wireless adapter to whatever IP network you want to connect to.
If you need to connect to your router again change the laptop's adapter IP to something like 192.168.200.2
Keep in mind nothing ever gets plugged into the Internet Port on the router.
What I do with these manufacturing machine's is put them on the company network with static IP's. Then so operators can transfer programs and view drawings I place ELO touchscreens at each location. For the Laser cutter operators that do nesting they have a desktop workstation for the CAD software and put the nests on a network share or direct to the laser cutters.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

New Intel WIFI Wireless Network Adapter does not recognize Wireless Router

I have had a Linksys BEFW11S4 Version 4 Wireless router for quite some time. It works like a champ and I have one Laptop wired to it and a second using Wireless working just fine. Recently, I received a new ThinkPad W500 Laptop with an Intel WIFI Link 5100 AGN wireless network adapter. The older laptop that works just fine with the router uses a
11a/b/g Wireless LAN Mini PCI Express Adapter by Atheros. However, the NEW laptop with the Intel Adapter fails to connect to the Router. It will either indicate a failure while "Waiting for Association" or it will indicate a failure when waiting to "renew IP Address". Sometimes, it will show a signal strength close to ZERO (Even as the older laptop with the other adapter is showing a signal strength close to 100%) When I called Linksys support, I was told that the facts that the Router (a) works find with the wired Laptop and (b) works fine with the 11a/b/g NEtwork Adapter and (c) works fine when WIRED to the new laptop all indicate that the problem is NOT with the router at all -- but with the Network Adapter. Can anyone tell me what has to be adjusted in the Adapter settings? Right now, I am using IBM Access Connections for BOTH of the wireless laptops. I have made sure to set IDENTICAL values for SSID and WEP (128-bit) [static] password. I have also ensured that all OTHER settings are the same for the two laptops. Yet, in one laptop, there is NO PROBLEM while in the other, I can not get the Wireless Adapter to "see" the signal from the Router. TO further check this, I have [temporarily] disabled the WEP password, enabled SSID broadcast, and disabled the MAC address restrictions that I put in (so that the system would be totally "open") yet the Intel Adapter STILL did not "find" anything. In addition, when I use the "Find WIFI" feature in Access Connections, I find that SOMETIMES the network with SSID is found and sometimes, it will display "unknown network" and not pick up the SSID.
This is all very frustrating. If anyone has experience with the Intel WIFI Link 5100 AGN Adapter, I would appreciate any hints, tricks, ideas, etc.
Think you!!!!
--Zvi

I installed the LATEST version of IBM Access Connections as well as verifying that I have teh LATEST drivers for the Intel Wireless NEtwork Adapter.
What now happens is that I am able to authenticate to the Router. However, I get a failure on "renewing IP Address" -- which [according to the diagnostic message] means that the Rotuer fails to provide me with an IP address to use. Do you have any suggestions?

Having issues with WRT54GS router acquiring network address after wireless connection.

I've been experiencing problems acquiring a network address after making a wireless connection with the WRT54GS wireless router. I have a Comcast cable modem connected to the internet port of the router and after configuring the SSID and the 64 bit WEP key, I can connect to my router's SSID, but since I can't get an IP address, never connect to the Internet. I've already cloned the laptop's mac address to no avail. Even after configuring a static IP address, subnet mask and default gateway, still cannot connect. I can Ping and Traceroute from the router but not the PC. I can ping localhost and host IP address from the laptop but not the default gateway. Any suggestions would be appreciated. Thanks, SJ

Connect the computer to the router with the Ethernet cable.
Try to access the internet when you connect the computer to the router with the Ethernet cable.
Open the setup page of the router and go to Status page. Check the Internet IP address on the status page of the router.
If you are able to access the Internet with the Wired connection to the router then try to create a new wireless network on your router.
Open the setup page of the router and go to Wireless tab. Change the wireless network name SSID and change the channel to 11. Save the settings. Go to Wireless security sub tab and check the wireless security settings. Click on Wireless MAC filter sub tab and make sure that it is disabled. Click on Advanced wireless settings sub tab. Change the Beacon Interval to 75, RTS and fragmentation threshold to 2304. Save the settings.
Try to connect to the new wireless network and see if that works.
How many wired and wireless computers do you have in the network?

Playstation 3 Wireless Network Enable Crashes WRT54G Wireless Router

I am trying to set up my wireless connection on my Playstation 3 via my WRT54G wireless router. Whenever I start at the beginning and select Enable for Wireless Connection, the wired end of my router which is attached to my cable modem crashes. My host wired PC loses it internet connection. As I proceed with my Playstation 3 Wireless Network setup, the PS3 can still wirelessly see my router. I do an automatic configuration, but the router is unable to assign a TCP/IP address to the PS3. My main problem is that the PS#crashes my router the moment I even enable the wireless connection. Any ideas?

I don’t think of anything else that a Firmware on this router. Download the latest firmware for this from http://www.linksys.com/download and Upgrade that to your router. Reset and reconfigure it, reduce the MTU to 1365, assign a static IP on PS3 and forward the ports needed by PS3 for this IP address. Now you should able to connect to this router wirelessly.

I want a new and more powerful (non-Apple) wireless router but I still want to use my existing Time Capsule to continue with my Time Machine backups and I still need the Time Capsule's Network Attached Storage (NAS) features and capabilities

THE SHORTER STORY
My goal is to successfully use my existing Time Capsule (TC) with a new and more powerful wireless router. I need a new and more powerful wireless router in order to reach a distant Denon a/v receiver that is physically located in a master bedroom some 50 feet away from my modem. I need to provide this Denon a/v receiver with an Internet connection so that it can obtain its firmware updates and I need to connect this Denon a/v receiver to my network in order to use its AirPlay feature. I believe l still need the TC's Network Attached Storage (NAS) features because I am not sure if the new wireless router will provide me with the NAS like features / capabilities I need to share files between my two Apple laptops with OS X 10.8.2. And I know that I absolutely need my TC's seamless integration with Apple's Time Machine (TM) application in order to continue to make effortless backups of my two Apple laptops. To my knowledge nothing works with TM like Apple's TC. I also need the hard disk storage space built into the TC.
I cannot use a long wired Ethernet cable connection in this apartment and I cannot use power-line adapters. I have read that wireless range extenders and repeaters are difficult to successfully set-up and that they will reduce data speeds, especially so when incorrectly set-up. I cannot relocate my modem and/or primary base station wireless router.
In short, I want to use my TC with my new and more powerful wireless router. I need to stop using the TC to connect to the modem. However, I still need the TC for seamless TM backups. I also need to use the TC's built in hard drive for storage. And I may still need the TC's NAS capabilities to share files wirelessly between laptops because I am assuming the new wireless router will not provide NAS capabilities for OS X 10.8.2 (products like this/non-Apple products rarely seem to work with OS X 10.8.2/Macs to provide NAS features and capabilities). Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone please advise on how to set-up my new Asus wireless router with my existing TC in such a way to accomplish all of this?
What is the best configuration or set-up to accomplish my above goals?
Thank you in advance for your assistance!!!
THE FULL STORY
I live in an apartment building where my existing Time Capsule (TC) is located in my living room and serves many purposes. Specially, my TC is at least all of the following:
(1) Wi-Fi router connected to Comcast Internet service via Motorola SB6121 cable modem - currently the TC is the Wi-Fi base station that connects to the modem and has the gateway address to the Internet. The TC now provides the DHCP service for the Wi-Fi network.
(2) Wireless router providing Internet and Wi-Fi network access to several Wi-Fi clients - two Apple laptop computers, an iPod touch, an iPad and an iPhone all connect wirelessly to the Internet via the TC.
(3) Wired Ethernet router providing Internet and Wi-Fi network access to three different devices - a Panasonic TV, LG Blu-Ray player and an Apple TV each use one of the three LAN ports on the back of the TC to gain access to the Internet.
(4) Primary base station in my attempt to extend my wireless network to a distant (located far away) Denon a/v receiver requiring a wired Ethernet connection - In addition to the TC, which is my primary base station, I am also using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. I cannot use a wired Ethernet connection to continuously travel from the living room to the master bedroom. The distance is too great as I cannot effectively hide the Ethernet cable in this apartment.
(5) Time Machine (TM) backup facilitator - I use my TC to wirelessly back-up two Apple laptops using Apple's Time Machine (TM) application. However, I ran out of storage space on my TC and therefore added external storage to it. Specifically, I added an external hard drive to my TC via the USB port on the back of the TC. I now use this added external hard drive connected to the TC via USB as the destination storage drive for my TM back-ups. I have partitioned the added external hard drive, and each of the several partitions all have enough storage space (e.g., each of the two partitions used by TM are sized at three times the hard drive space of each laptop, etc.). Everything works flawlessly.
(6) Network Attached Storage (NAS) - In addition to using the TC's Network Attached Storage (NAS) capabilities to wirelessly back-up two Apple laptops via TM, I also store other additional files on both (A) the hard drive built into the TC and (B) the additional external hard drive connected to the TC via USB (there are additional separate partitions on this drive for these other additional and non-TM backup files).
I use the TC's NAS feature with my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Again, everything works wirelessly and flawlessly. (Note: the Apple TV is connected to the network via Ethernet and a LAN port on the back of the TC).
The issue I am having is when I try to listen to music via Apple's AirPlay in the master bedroom. This master bedroom is located at a distance of two rooms away from the TC's current location in the living room, which is a distance of about 50 feet. This apartment has a long rectangular floor plan where each room is connected to the next in a straight line. In order to use AirPlay in the master bedroom I am using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. This additional base station connects wirelessly to the WiFi network provided by my TC and then gives my Denon receiver the wired Ethernet connection it needs to use AirPlay. I have tried moving my iTunes music directly onto my laptop's hard drive, and then I used AirPlay on this same laptop to connect to the Denon receiver. I always get a successful connection and the song plays, but the problem is that the connection inevitably drops.
I live in an apartment building and all of the many wireless routers in this building create a great deal of WiFi interference on both the 2.4 GHz and 5GHz bands. I have tried connecting the Netgear product to each the 2.4 and 5 GHz bands, but neither band can successfully maintain a wireless connection between the TC and the Netgear product. I also attempted to maintain a wireless connection to an iPod touch using the 2.4 GHz band and AirPlay on this iPod touch to play music on the Denon receiver. Again, I was able to establish a connection and successfully play music, but after a few minutes the connection dropped and the music stopped playing. I therefore have concluded that I have a poor wireless connection in the master bedroom. I can establish a connection, but it is intermittent with frequent drops. I have verified this with both laptops by working in the master bedroom for an entire day on both laptops. The Internet connection in this master bedroom proved to drop out frequently - about once an hour with the laptops. The wireless connection and the frequency of its dropout are far worse with the iPod touch and an iPhone.
I cannot relocate the TC. Also, this is an apartment and I therefore cannot extend the range of my network with Ethernet cable (I cannot drill through walls/ceilings, etc.). It is an old building with antiquated wiring and power-line adapters are not likely to function properly, nor can I spare the direct power outlet required with a power-line adapter. I simply need every outlet I can get and cannot afford to block any direct outlet.
My solution is to use a more powerful wireless router. I found the ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router which will likely provide a better connection to my wireless Internet in the master bedroom than the TC. The 802.11ac band of this Asus wireless router is totally useless to me, but based on what I have read I believe this router will provide a stronger connection at greater distances then my TC. And I will be ready for 802.11ac when it becomes more widely available.
However, I still need to maintain the TC's ability to work seamlessly with TM to backup my two laptops. Also, I doubt the new Asus router will provide OS X 10.8.2 with NAS like features and capabilities. Therefore, I still would like to use the TC's NAS capabilities to share files on my network wirelessly assuming the Asus wireless router fails to provide this feature. I need a new and more powerful wireless router, but I need to maintain the TC's NAS features and seamless integration with TM. Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone advise on how to set-up my existing TC with this new Asus wireless router in such a way to accomplish all of this?
Modem
Motorola SB6121 SURFboard DOCSIS 3.0 Cable Modem
Existing Wireless Router and Primary Wi-Fi Base Station - Apple Time Capsule
Apple Time Capsule MC343LL/A 1TB Sim DualBand (purchased June 2010, likely the Winter 2009 Model)
Desired New Wireless Router and Primary Wi-Fi Base Station - Non-Apple Asus
ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router
Extended Wi-Fi Base Station - Provides an Ethernet Connection to a Denon A/V Receiver Two Rooms Away from the Modem
Netgear Universal Dual Band Wireless Internet Adapter for TV & Blu-Ray (WNCE3001)
Addition External Hard Drive Attached to the Existing Apple Time Capsule via USB
WD My Book Studio 4TB Mac External Hard Drive Storage USB 3.0
Existing Laptops on the Wireless Network Requiring Time Machine Backups
MacBook Air (11-inch, Mid 2012) OS X 10.8.2
MacBook Pro (13-inch Mid 2010) OS X 10.8.2
Other Existing Apple Products (Clients) on the Wireless Network
iPod Touch (second generation) is model A1288.
iPad (1st generation)
Apple TV (3rd generation) - Quantity two (2)

Thanks Bob Timmons.
In regards to a Plan B, I hear ya brother. I am already on what feels like Plan Z. Getting WiFi to a far off room in an apartment building crowded with WiFi routers is a major pain.
I am basing my thoughts on the potential of a new and more powerful router reaching the far off master bedroom based on positive reviews on cnet.com, pcmag.com and pcworld.com. All 3 of these web sites have reviewed the Asus RT-AC66U 802.11AC wireless router as well as its virtual twin cousin 802.11n router. What impressed me is that all 3 sites rated this router #1 overall in terms of both range and speed (in both the 802.11n and 802.11AC flavors). They tested the router in real world scenarios where the router needed to compete with a lot of other wireless routers. One of the sites even buried this Asus router in a media room with thick walls and inside a media cabinet. This Asus router should be able to serve my 2.4 GHz band wireless clients (iPod Touch and iPhone 4) with a 2.4GHz Wireless-N band offering some 50 feet of dependable range and a 60 Mbps throughput at that range. I am hoping that works, but it's borderline for my master bedroom. My 5 GHz wireless clients (laptops) will enjoy a 5GHz Wireless-N band offering 150 feet of range and a 200 Mbps throughput at that range. I have no idea what most of that stuff means, but I did also read that Asus could reach 300 feet and I got really excited. My mileage may vary of course and I'm sure I'm making some mistakes in my interpretation of their data. However, my Winter 2009 Time Capsule was rated by cnet.com to deliver real world performance of less than that, and 802.11AC may or may not be useful to me someday. But when this Asus arrives and provides anything other than an excellent and consistent wireless signal without drops in the master bedroom it's going right back!
Your solution sounds great, but I have some questions. I'm using OS X 10.8.2 and Airport Utility (version 6.1 610.31) and on its third tab labeled "Wireless" the top option enables you to set "Network Mode" to either:
Create a wireless network
Extend a wireless network
Off
Given your advice to "Turn off the wireless on the TC," should I set Network Mode to Off? Sorry, I'm clueless in regards to how to turn off the wireless on the TC any other way. Can you provide specific steps on how to turn off the wireless on the TC? If what I wrote is correct then what should the rest of this Wireless tab look like, or perhaps it is irrelevant when wireless is off?
Next, what do you mean by "Configure the TC in Bridge Mode?" Under Airports Utility's fourth tab labeled "Network" the top option "Router Mode" allows for either:
DHCP and Nat
DHCP Only
Off (Bridge Mode)
Is your advice to Configure the TC in Bridge Mode as simple as setting Router Mode to Off (Bridge Mode)? If yes, then what should the rest of this "Network" tab look like? Anything else involved in configuring the TC in Bridge Mode or is it really as simple as setting the Router Mode to "Off (Bridge Mode)"?
How about the other tabs in Airport Utility, can they all stay as is assuming I use the same network name and password for the new Asus wireless router? Or do I need to make any other changes to the TC via Airport Utility?
Finally, in regards to your Plan B suggestion. I agree. But do you have a Plan B for me? I would greatly appreciate any alternative you could provide. Specifically, if you needed a TC's Internet connection to reach a far off corner of your home how would you do it? In the master bedroom I need both a wired Ethernet connection for the Denon a/v receiver and wireless Internet connection for the iPhone and iPod Touch.
Power-Line Adapters - High Cost, Blocks at Least One Wall Outlet and Does Not Solve the Wireless Need
I actually like exactly one power-line adapter, which is the D-Link DHP-540 PowerLine AV 500 4-Port Gigabit Switch. This D-Link power-line adapter plugs into your wall outlet with a normal sized plug (regular standard power cord much like any other electronic device) instead of all of the other recommended power-line adapters that not only use at least one wall outlet but also often block the second outlet. You cannot use a power strip with a power-line adapter which is very impractical for me. And everything about my home is strange and upside down. The wiring here is a disaster and I don't have faith in its ability to carry Internet access from the living room to the master bedroom. And this D-Link power-line adapter costs $90 each and I need at least two to make the connection to the Denon A/V receiver. So, $180 on this solution and I still don't have a dependable drop free wireless connection in the master bedroom. The Denon might get its Ethernet Internet connection from the power-line adapter, but if I want to use an iPhone 4 or iPod Touch to stream AirPlay music to the Denon wirelessly (Pandora/iTunes, etc.) from the master bedroom the wireless connection will not be stable in there and I've already spent $190 on just the two power-line adapters needed.
Extenders / Repeaters / Wirelessly Extending the Wireless Network
I have also read great things about the Amped Wireless High Power Wireless-N 600mW Gigabit Dual Band Range Extender (Repeater) SR20000G and the My Net Wi-Fi Range Extender. The former is very powerful and the latter is easier to install. Both cost about $150 ish so similar to a new Asus router. However, everything I read about Range Extenders points to them not being very effective for a far off corner of your house wherein it's apparently hard to place the range extender in the sweet spot where it both gets a strong enough signal to actually effectively extend the wireless signal and otherwise does not reduce network throughput speeds to unacceptable speeds.
Creating a Roaming Network By Hard Wiring with Ethernet Cable - Wife Would Say, "**** No!"
Even Apple seems to warn against wirelessly extending your network (see: http://support.apple.com/kb/HT4145#) and otherwise strongly recommends a roaming network where Ethernet cable is used to connect two wireless base stations. However, I am in an apartment where stringing together two wireless base stations with Ethernet cable would have an extremely low wife acceptance factor (WAF). I cannot (both contractually and from a skill prospective) hide Ethernet wire in the walls or ceiling. And having visible Ethernet cable running from room-to-room would be unacceptable, especially to the wife.
So what is left? Do you have a Plan B for me? Thanks in advance for your help!

WRT400N wireless router industrial network static IP

Similar Messages

Maybe you are looking for