WRT54G 1.1 Wireless works, but Ethernet does not

Evening,
This evening, I flashed the firmware on my WRT54G V1.1.
Everything went fine, and it said click continue to continue, which I did.
I tried to reset back to defaults (button on back), which as far as I know took, but I still can not access via wired connections. For the heck of it, I hopped on the laptop. Sure enough, the settings did take, because I could see and connect to the default settings (SSID of linksys, default pass, etc).
I looked in the configuration page, and see that it is not pulling an IP from the cable modem. I reset the modem, reset the router, but still can not connect via wired.
I even set my ethernet to a static IP (192.168.1.55) with a 255.255.255.0 mask, and cant even ping the router (192.168.1.1), however, I can ping it on the laptop connected via the wireless.
It appears all my ethernet ports are dead, but, just from an upgrade?
Anyone have any idea?
Any help would be appreciated, thanks.

Hi… Reduce the MTU on that router and check if you can get the connection on wired PCs. Or else reduce the Card speed (link, speed and duplex) to 10 Mb half duplex. This should give you a connection. For internet IP address, make sure you clone the MAC address of the Wired PC to this router (MAC Address clone sub-tab under setup) and power cycle the network. You can also try resetting the router for 1 min again.

Similar Messages

  • Wireless works, but ethernet does not OfficeJet Pro 8600

    I just purchased an OfficeJet Pro 8600 and can't get it to work on the ethernet port.  The printer states that it is not connected.  I know the calbe works because I can print to a different printer when attached to that cable.  Any assistance is appreciated.

    Hello Gail123,
    I am sorry to hear about the issues connecting your Officejet 8600. I understand you have tried many many steps on your own and the printer is still not detecting the ethernet cable.
    As you mentioned the unit is right out of the box and still not functioning correctly after all of the steps you have taken, I suggest calling HP's Technical Support to inquire about a replacement unit.
    If you are calling within North America, the toll free number is 1-800-474-6836.
    Good luck to you!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Airport express: wireless works, but internet does not

    Hello.
    It happened yesterday for no apparent reason: Internet was not working via airport anymore, as it should have normally.
    Config: Cable modem to Airport extreme (.g); USB printer attached to base station, base station Ethernet port going to router with Boradband phone and 1 PC attached to it.
    4 MAc computers attached to Network (and getting Internet) via Airport.
    Internet connection using DHCP, dynamic IP address provided by RoadRunner (Time Warner).
    I tested Cable Modem (works), all ethernet cables (good), reset base station and recreated an airport network.
    Airpot network works, USB printer is accessible via Airport, but Internet is still off (although Network Configuration in Sys Pref give me a green light and informs me that I am connected to the internet)
    My question: is it possible that Base Station fails only for its Internet/WAN capability, and not for Network functions?
    thanks. This one is a puzzler.
    Paul

    Hello.
    We have been having the same problem discussed in this thread earlier, described as follows:
    It happened two days ago for no apparent reason:
    Internet was not working via Airport Express anymore, as it
    should have normally.
    Config: Cable modem to Airport Express via a US Robotics router,
    2 MAC computers (iMac700 and MacMini) attached to Network (and getting
    Internet), the iMac through router and the MacMini via Airport Express.
    Internet connection using DHCP, dynamic IP address
    provided by RoadRunner (Time Warner).
    iMac connected to router is getting Internet just fine; MacMini connected to network via AEX is getting network signal but no Internet. Network diagnostics says it can't tell what's wrong and call ISP. ISP says it's an Apple problem.
    I tested Cable Modem (works), all ethernet cables
    (good), Airport Express network works, but Internet is still off for MacMini.
    I've done a power recycling exercise twice, but still no Internet on the MacMini.
    Does anyone have any ideas? Both my son and I are stumped. He's a teenager and is fairly computer savvy. Neither of us has been able to figure this out.
    Joe

  • Internet Download Manager cannot integration with firefox4 itis Look in the menus it works but it does not actually work ?

    internet Download Manager cannot integration with firefox4 its Look in the menus it works but it does not actually work

    IDM may need to be updated to work with Firefox 4.0. You could contact them and make them aware of the problems you are having with their program.

  • Why are my tags not syncing for a shared email account? IE One person tags an email as "Work" but it does not show on other users Thunderbird.

    Subject says it all for the most part.
    A shared email account we'll call "[email protected]" is not syncing tags across other end users Thunderbird. User A will tag an email as Work but it will not sync/show on anyone else's application. I've read that Thunderbird stores tags locally now? Is there a way to sync them up to our IMAP server? Or would we have to revert to a previous version of Thunderbird (if so which)?
    Any help is greatly appreciated. Thanks

    the issue is probably that the server does not support tags..... Thunderbird stores them locally, but syncs them were the server supports it.

  • TC works on ethernet, does not on wifi, but wifi works

    Hi,
    having problems with my Time Capsule. It was working fine until a few weeks ago, then after a long absence it stopped to work (I didn't see backups updated). I switched off the TC, then switched on, no change.  I tried with a ethernet cable, and backup was done smoothly. Back to wifi, I tried to remove the com.apple.TimeMachine.plist file from /Library/Preferences, but backup through wifi didn't work.  Time machine got stuck at the "Preparring Backup" stage forever.
    However, the wifi works.My lMacBook Air is now connected to the internet through the TC wifi, and I can enter the TC for old backups using the wifi.
    The same behavior is occurring with my wife MacBook.
    Any suggestion ?
    Thanks,
    Luigi

    Your confusing me now..
    To add, if I connect the wifi to the TC wifi, it works. If I connect the wifi to my adsl router, it does not. However, if I have the wifi connected to the adsl router, I can see the TC in Airport, as working fine.
    But in no case does the TM backup work?? Does the TM work if you connect to the adsl router wifi instead of the TC wifi?
    So you have the adsl modem as your main router. The TC should be in bridge.
    I have a few tasks for you.. none of which is guaranteed to work but we should be able to fix it.
    1. Downgrade the firmware.. you can try the following steps without doing this.. but 7.6.4 is not helping.
    In v6 utility in Lion you can simply select the TC, option click on version.. and all the older firmware will appear. Select 7.6.1 and downgrade.
    2. Factory reset.
    The Factory Reset TC Gen1-4. Or AE Gen1-5
    Unplug your TC/AE. Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec.
    Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
    No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    3. Redo the setup.
    Use all SMB type names.. eg.. TCGen4 as TC name.. it is short, no spaces and pure alphanumeric.
    Use TC24ghz for 2.4ghz wireless. Use TC5ghz for 5ghz wireless.. yes, use different names at least until you work out the issues.
    Use WPA2 Personal security with a 10-20 character full alphanumeric password.
    4. Delete the current TM setup and start again.
    See A4 here. http://pondini.org/TM/Troubleshooting.html
    So you will select the newly named TC but the TM should find your old backups and continue to use them.. only Mavericks it seems is too stupid to do this.
    5. See if TM now works by wireless.

  • Weirdness: http works but https does not

    I have a very weird problem which no-one has been able to fix.
    I have an Airport Extreme card and a third-party DSL modem / wireless router combo. Most internet activities are fine (ftp, email, http) but whenever I try to access a secure site (https) or run a VPN connection (Apani Netlock) one of three things happen:
    1. I spontaneously disassociate from my WiFi base station, losing the wireless connection. If I cancel the https request or close down the VPN, the wireless link comes back after 5-10 seconds.
    2. I get TCP/IP timeouts - no responses from server.
    3. It works, but extremely slowly. Loading a single https web page can take anywhere between 30 seconds to 3 minutes. I'm on a 1.5 Mb/s DSL link.
    Things I have tried:
    1. Connecting by ethernet directly to the router instead of using 802.11b/g - all the problems go away. So it is not a DSL modem or ISP issue.
    2. Changing the MTU of the Airport Extreme card (en1). I have tried values from 600 to 1492. Same problems exist - makes no difference.
    3. Tried an Apple Airport base station connected by ethernet to the modem instead of using the modem's wireless. Same problems exist, although the VPN doesn't work at all (even slowly) because the ABS does not support that particular VPN protocol.
    I'm at my wits end. No one I have spoken to at tech support at the ISP or modem manufacturer have ever heard of such a problem.
    HELP!

    Ok, it's some years later. and the problem has gone away. Things which may have fixed it: OS software upgrades, client software upgrades, better signal strength (this problem did seem more prevalent at low WiFi signal strengths).

  • Wireless works, direct connect does not

    I have a WRT54G wireless router. I woke up this morning to find that my wired connection does not work to my desktop but my wirelesss connection to my laptop does work.  I tried rebooting and changing ports- the same.  The cableing has not been moved.  Any Suggestions?

    Sorry- hit enter...  If I go to start/settings/ network connections, there is no LAN icon on the desktop, only a network bridge icon.  A LAN icon as well as the wireless connection icon is seen on the laptop through that thread.  Online chat support with Norton did not help- I will try againin a few days with them.  I'm also looking in the chat forums on CNet, some talk about SP3 as the cause, but my log does not show that I have loaded that.  BTW, I have XP os, and Norton Internet Security 2008, and my laptop works wired from the same cable that goes to my tower.  I will keep looking for answers and post what I find. Let me know if I'm overlooking something.  Thanks.

  • TS3367 facetime used to work but now does not work on any of my devices

    I have been in regular contact until about 4 days ago using facetime on my iphone 5 imac 10.7.5. ipad 2 now none of these devices work from incoming calls from Philipinnes. Take note the caller had latest macbook pro 13 inch  and is able to call Guam on fatetime with success. What is happening why is incoming calls alway failing. This has been 4 days running and is not good enough. Okay I havent got the latest updates but why in the late few days whould this effect anything. I mean 3 devices and none of them work. This is most frustrating and annoying. I have intead used skype which does work but at night time the camera is not as clear. Tanke note also earlier in the year I received calls from Vietnam and although I did have dropouts was always able to connect only these last four days have had no success. Also I have not been able to call out. The wireless has full bar and am near the modem that is not an issue. Unless there has been a recent change why is htis not working all of a sudden.

    THere seems to be a FaceTime issue and some users who have been in contact with Apple support claim that Apple is working on this.
    I have read many posts on the issue and have seen that there are many reporting that when they have updated their various devices to the latest software, the issue has been resolved.
    You can wait for Apple to resolve the issue OR you can update everything to the latest software and see if this solves your issues.

  • Time Capsule: IPv6 works, but IPv4 does not

    I have a Time Capsule (running 7.7.3) and a Mac Pro (2010, running 10.10.1) connected via ethernet. My ISP (Webpass) has IPv6 support.
    The Mac Pro can communicate over IPv6 (e.g. ping6 google.com works; I can load google.com over IPv6 using Safari).
    However, IPv4 does not work. The Mac Pro isn't even getting an IPv4 address via DHCP from the Time Capsule.
    I'm pretty sure I have my IPv4 configuration correct in the Time Capsule, because if I turn on wifi on the Mac Pro (using the Time Capsule as my base station), the wifi interface gets an IPv4 address, and can reach the Internet over IPv4.
    Possibly relevant: 3 days ago I noticed that IPv6 wasn't being routed properly by my ISP, so I filed a trouble ticket. They fixed it 2 days ago, which is when my wired IPv4 networking broke. (Given that I can use IPv4 via wifi suggests that the problem lies with the Time Capsule).
    I have tried rebooting the Time Capsule and different ethernet ports on both the Time Capsule and Mac Pro, to no avail.
    How can I get wired IPv4 working again?

    I wish you were running anything but yosemite on the computer as it is least reliable networking OS yet.
    Factory reset the TC. Redo the setup.. please use all short names, no spaces and pure alphanumeric.. do not use the names apple wizard will recommend.. keep passwords also 8-20 character pure alphanumeric but mixed case and numbers.
    In ethernet setup of the computer.. how have you got ipv6 set??
    How is ipv4 set?
    Have you tried static address in the Mac?
    What sort of broadband is this?? If there is a modem what sort? And what mode is the TC running in?
    One of the strange things that can happen.. with IPv6 you can use TC bridged to a fibre connection..
    But for ipv4 to work it must be set to DHCP and NAT in the network tab.

  • After upgrading to 10.2.2.12  on windows XP SP3 , itunes does not display any summary info or buttons/options. The buttons work but it does not display the text on the button or the options available.

    I recently upgraded the iTunes software to 10.2.2.12 on my Windows XP laptop. Since then, iTunes stopped displaying the Summary info
    , the text on the buttons, the various drop down options. The buttons seem to be working but I can't tell what that button is supposed to do
    or the option I am selecting. This is preventing me from syncing my photos to the laptop.
    this was not a problem with the previous version of iTunes.
    Actions taken :
    - I tried downloading iTunes again and repairing the install. That did not fix it.
    - Don't want to uninstall it as I am worried that I would lose all the songs and the purchases etc.
    1. Has anyone encountered this ?
    2. Is there a solution for this ?
    Many thanks in advance for your time and help
    Nitin

    bmalones44 wrote:
    b noir, my Windows 7 machine is having the exact same issue as nsadal, and I have already confirmed that all six of the Segoe UI fonts are installed on my computer.  Are any other Windows users having this problem with the 10.2.2.12 iTunes release?
    Yeah it does, although the problem predates version 10.2.2.12. It's been around since earlier-on in the version 10s (at least).
    It's usually Segoe UI font trouble on the Windows 7 systems too. Unfortunately, the Vortical troubleshooting technique only works on XP and Vista systems, so dealing with the issue on a Windows 7 system is trickier. (There's a bunch of different possible issues relating to the fonts that could be in play, and so the treatment tends to depend on which issue in particular you've got with the Segoe_UI fonts.)
    For discussions of various Windows 7 variations of the "Missing text" thing, and possible treatments, see the following (unfortunately, rather long) topic:
    iTunes 10.1 Missing Text

  • Continuity calling works but Handoff does not.

    I got continuity calling to work by doing the on & off tricks with my iPhone 6 and iPad 4, but Handoff still does not work.

    Hi.
    Continuity works one way here: I can continue on my Mac, but not vice versa, Also cellular calling worked that way: receive on Mac works but no outgoing calls. I managed to get the latter work by switching a setting in FaceTime preferences, but continuity discontinues to work both ways.
    Klaus Löfflad
    Spezialist für Apple Produkte
    http://train4media.de

  • I need to place the Maltese cross on a web page. IE works, Safari works, but Firefox does not. It is wingding character.

    The Maltese cross is in the winding font family. I have the following HTML on the pages:
    <pre><nowiki>
    <span class="cross" style="font-family: wingdings; vertical-align: top;">X</span></nowiki></pre>
    The inline element <span> tag is in a <font> tag.
    CSS: span.cross { color: #000; font-size: 16pt; font-weight: bold; }
    This has been working for years in IE 5, 6, 7 & 8, works also in safari (latest rev), but does not work in FireFox rev 4.0.1. FoxFire displays a large X instead of the Maltese cross.
    Other than this small problem FoxFire works great, especially with HTML5 & CSS3.
    Any help would be appreciated.
    DonL

    This concerns the Maltese cross problem. When I posted the problem, the data inside "<" and ">" characters is lost. The only thing that showed was the "X".
    I posted the HTML used to display the cross w/o these chars.
    span class="cross" style="font-family: wingdings; vertical-align: top" X /span
    Thanks for any help.
    DonL

  • Setter works but Getter does not

    Hi all,
    I have had relatively little problems with setting up and running Entity Ejb's as of yet with simple beans (with 2 attributes only). The below problems seems to be implemented in the same way as the smaller been, with the only difference being that this bean has 6 attributes.
    Quite simply,
    I have no problems setting up the EJB, deployement of EJB, and the running of the server.
    I have created a testing program that creates a new instance of the bean, looks up a bean, sets one of the attributes of the bean and then uses a getter method to check to see if the setter works.
    Out of all of the above I thought the simplest thing to use would be the getter method. But this is the area that I get the exception.
    As I said everything else works, I can even check the database to check if the setter method works, and it does.
    The exception that is called is:
    <code>
    java.rmi.ServerException: RemoteException occurred in the server thread; nested exception is:
    java.rmi.RemoteException: Exception is in getAddress: nested Exception is:
    javax.ejb.NoSuchEntityException
    </code>
    The name of the getter method that is called is getAddress, as seen above.
    Please could anyone help.
    Thanking you
    Damian

    Hi all,
    I have been working on the problem now for a little more and I have worked something out.
    I worked through everything and tried to work out what was out of the ordinary. I realized that I had an attribute in the bean of type java.util.Date. While all other attributes were of type String. When I created the bean with out the Date column, the getter methods for all the other attributes seem to work (unlike before).
    Why has this made a difference, what is it about having a setter and a getter method for datatype Date that affects all of the other getter methods.
    Of course I want to be able to have fields with datatype of Date, so please people help me on this one.
    Damian

  • Video Works but Mic Does Not

    I have a Creative Livecam Socialize HD(VF0616) installed in my PC. My OS is Win7 Ultimate 64 Bit. The camera was working before but I have not used it lately. I upgraded my Skype but when I tested it with the camera, the mic did not work. The camera video and the speaker seemed OK but the microphone did not work. Any simple way to test the mic feature of the camera?

    In Skype go to Tools -> Options -> Audio settings. What device do you see there selected as your Microphone? Is there more than one option available in the selection box? Can you see any respponse on the Volume bar when you make any sound?

Maybe you are looking for