WRT54G and Xbox 360 with no internet
New Xbox 360 hard wired to router WRT54G, router recognize xbox but will not connect to internet. What do i need to change?
Solved!
Go to Solution.
If your router's IP Address is 192.168.2.1...
Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.2.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.2.1...
Also you can upgrade the firmware on your router if the connection is slow when you use your XBox...You can download the firmware from here
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.2.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...
Then, unplug the power cable while holding down the reset button for another 30 Seconds...
Plug the power cable back in, and keep holding down the reset button for another 30 Seconds...
Release the reset button...To re-configure your router follow this
Do the Port Forwarding as mentioned earlier...
Similar Messages
-
I am using my wrt54g for my xbox 360. I am using an ethernet connection between them instead of a wireless connection. I talked to xbox and got the port numbers I needed and I opened them up on the router.
The port light where the ethernet plug for the 360 is in is flashing and my xbox is seeing no ip address at all. I don't know if I have my ip address correct for the ports, Please Help!Kindly do these settings on your router for X-Box...
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
3) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
4) Click on set-up and change the MTU Size to 1452 and click Save Settings...
5) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
6) Also assign the DNS Addresses on the Xbox
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
7) Turn off your modem, router, and Xbox...Wait for a minute...
8) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect... -
Wrt54g and xbox 360 wireless gaming adapter
First post here and I have a problem. The WRT54G has wirlelss disabled. It is connected to a WAP11B wireless access point which is connected in 802.11b mode to a laptop, Wii, xbox 360, iPhone. The router is connected to a dsl modem. Three wired ethernet computers are connected. And I am running WEP with 128, and I changed the SSID to something other than linksys.
I'd like to change to use the WRT54G as a wireless enabled connection. Then remove the WAP11B, and put a pcmcia 802.11g card in the laptop and connect the xbox360 with a microsoft xbox 360 wireless gaming adapter which should connect at 802.11g.
The problem is the xbox 360 displays a message that there are duplicate networks using my SSID. Is there someway to upgrade to 802.11g without getting that error message on the xbox 360? Let me know if there are any questions I can answer in order to more clearly explain the problem.
Thank you,
Jordan
Solved!
Go to Solution.Did you try to change the SSID...If not change the Network SSID and try...
-
I am considering buying an airport but I am not sure if it will work how I would like it to. I need it for two things. The first would be to use for AirPlay with my home stereo. The second would be to use as a way to give my Xbox 360 a WIRED internet connection via the ethernet port. I would like to do these things simultaneously, rather than constantly changing the configuration and being limited to a single function each time I do so.
Thanks!The 802.11n AirPort Express Base Station (AXn) can be configured as a wireless Ethernet bridge. In this configuration, it would join an existing wireless network and its Ethernet port would be enabled for a wired client, like your Xbox 360. This configuration would also support AirPlay simultaneously.
-
WRT54GX4 Wireless Router and Xbox 360 Wireless Networking Adapter
I just got an Xbox 360 with a Wireless Networking Adapter. The adapter will recognize the network, but won't connect to it. Even if I remove the security, the Xbox 360 won't connect. Is there something else via the router I'm supposed to be doing? I called Microsoft and they said to open the port settings, but I don't know if that's really the issue and I don't know how to do that if I need to.
The ports they gave me were:
TCP 80
UDP 88
UDP 3074
TCP 3074
UDP 53
TCP 53
Thanks for any help if you can.Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
3) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
4) Click on set-up and change the MTU Size to 1452 and click Save Settings...
5) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
6) Also assign the DNS Addresses on the Xbox
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
7) Turn off your modem, router, and Xbox...Wait for a minute...
8) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect... -
E2000 and XBox 360 Wifi Failed Connection
my new e2000 is connected to the internet and works for the IPAD (wifi) and desktop pc (wired), while our new xbox 360 with built in wifi recognizes the e2000, but wont connect so I can get xbox live. I spent 2 hours with xbox and cisco support. the error message continues to tell me there is an internet connection issue. I've followed all the help online and via phone support and then Cisco wants me to pay $70 for third party assistance to guarantee connection. It seems that the xbox should require me to enter the e2000 password to connect, but I have yet had a place to prompt me to enter it. How do I get these two systems to talk? It's either an xbox setting or a cisco setting that I can't figure out. Any help will be appreciated. Do I need to buy the e3000?
ThanksAccess the page of your router
Trigger ports: 3074/53/88/22728/33233
2869/10280-10284/1900/1024
Click Applications and Gaming Center Tab
Click Port Range Trigger
Ex:
Application name: xbox1, xbox2
xbox1--enter port 3074 on all 4 boxes and click enable
xbox2--enter 10280 on start box and 10284 on end box, same for the other 2 boxes and click enable.
Enter all number and on the applications boxes and save -
I am not new to this and I DO know what I'm doing. I have the network set up the way it always has been. Its ethernet, and its going through the switch and Fios router. I recently downloaded Starz Play and it works great on my Desktop, Laptop, but NOT on my 360. I have been streaming Vista MCE to it for months, and it all works GREAT with no network interference of any sort. The application doesnt show my 360 as an available device for it to extend to, so I am stumped. I searched the interwebs already, so any advice is more than appreciated. Thanks!
From Starz Play FAQ under "Connect to your TV"
"Connecting Starz Play To Your TV
Starz Play offers many very simple ways of connecting Starz Play to your TV for your viewing pleasure. For XP MCE and Vista MCE users you can choose to connect your TV to your computer Using the XBOX 360 as an extender.
It's easy to have room-to-room entertainment throughout your home with a PC running Microsoft Windows XP Media Center Edition 2005 and Xbox 360. All you need are a few components to get things started:
• A PC running Microsoft Windows XP Media Center Edition 2005 or Vista with MCE
• An Xbox 360 with the Xbox 360 Wireless Media Adapter
• A wired or wireless (preferably 802.11a) home network
• A broadband Internet connection
With your Media Center PC hooked up to your home network, you're ready to introduce the Xbox 360 to the mix so you can start enjoying your photos, music, movies, and recorded TV in other rooms of your home. You can experience all this in high-definition if you've got a TV or monitor that can deliver it.
Please Click Here for step by step instructions from Microsoft on connecting XBOX 360 to your PC as a media extended.
The link then sends you here: http://www.microsoft.com/windowsxp/mediacenter/extender/setup/default.mspx
Again, any help is appreciated. -
Open nat type for xbox 360 with wrt160n?
How can I open my nat type on the xbox 360 with my wrt160n?
Currently it is on moderate..........I had this same problem, I had to enable three things. enable UPnP, enable Allow users to make congiguration changes, enable Allow users to disable internet access. You most likely have the first two I mentioned enabled but the last one is the one I didn't have enabled and once I enabled then I had open NAT
-
Free Xbox 360 with $700 or up Windows Laptop
I have gotten the coupon using my .edu email for the free Xbox 360 with a laptop purchase of $699 or higher from College Student Deals
but have seen that it says I need a valid student ID to get the deal. I have just graduated from high school and have not gone to orientation yet so I do not have a student ID from college yet. I have a high school student ID still. Does anybody know if they really check for IDs or if a high school ID would work? If not, there are other online places I can get the PC and get the laptop using only my .edu email, such as the Microsoft Store, HPDirect.com, NewEgg, and Dell.com and I will get a computer from one of those sources. I only wanted to get my laptop at BestBuy because I can g check out the laptop before I purchase it plus I hate waiting for shipping. I get impatient when having to wait for items ordered. Any help would be appreciated. Thanks!As long as you have an acceptance letter and your .edu address.
If you like my post, or solution to your issue/question, go ahead and click on the little star by my name and/or accept the post as the Solution. It makes me happy.
I'm NOT an employee of Best Buy, or Geek Squad, though I did work as an Agent for a year 5 years ago. None of my posts are to be taken as the official stance that Best Buy will take on your situation. My advice is just that, advice.
Unfortunately, that's the bad luck of any electronic, there's going to be bad Apples... wait that's a horrible pun. -
Updated to 7.3.1, PC and Xbox 360 can't connect
Hey, anyone else having problems getting PCs and Xbox 360s to connect to the AirPort Extreme after the 7.3.1 update? Wired or wireless, my PC (Vista, with and without SP1) and my Xbox 360 (with the official wireless network adapter) won't connect.
I am in the same boat...
7.2 worked great... 7.3.1 does not even show in the network list. Also, downgrading it does not fix the issue?!?!?
- Jay -
Any plans on having Skype App for Xbox 360 with Kinect?
I'm extremely disappointed with this response. I've been a fan of windows for my entire life. I was even a microsoft developer for 12 years. However, Microsoft is dropping the ball and I'm finding it extremely difficult to continue my loyalty.
1. Windows 8 == failure (Vista all over)
2. Love the tablet but can't justify the cost (Bought Android which is equally as good for 1/2-1/3 the price)
3. Love the phone and xbox integration
4. Extremely pissed off that a multi billion dollar company can't answer a simple question and just leave everyone asking questions that go unanswered.
I may just end up buying sony and going android. I have no more loyalty and I have done nothing but stick up for you for years. -
Can I use xbox 360 with thunderbolt display
Is it possible to use an Xbox 360 with a thunderbolt display? If so, I need specifics of what I would need to do so.
Not unless your 360 has a TB port.
-
Step by step complete setup for WRT54G ver.6 with Laptop and XBOX 360
Hello. I am sorry to post this, I am sure it is a juevenile and redundent question...but I have tried to look for the set up cd (I can find where to download it...though I can find the firmware upgrade or whatever). My friend at work said it would do all the setup pretty much automatically for me.
I somewhat know computers, but you might go ahead and make your replies VERY lamen's terms or I might not be able to follow. Anyways, what I need, is a step by step/screen by screen directions for a secure network. I have made a partial attempt at setting it up and it technically works, but I would feel better if I did the steps a-z in order, so I know that it is done correctly. I also am not totally confident in its security as it is now. (Also, technically, I did not check the XBOX again after getting the new laptop, I am just assuming it is still working because it was before).
My problem is I can't seem to find very good directions for setting up the router...I only find partials or confusing directions.
So here are the things I am trying to connect:
Liksys WRT54G ver. 6
Gateway Laptop running Windows Vista
XBOX 360 - WIRED
(I had a PC and a laptop, but they both died at the same time and I have only been able to replace the laptop at this point...the PC will come later and not sure at this point if it will be Wired or not).
I have a cable Modem between the Router and the wall...I didn't look at that for brand/etc...but I can get it ASAP if needed.
Here are the settings that I have so far:
Changed the Router Name
Changed the SSID
Have DHCP set to 3 (XBOX, PC, Laptop)
Wireless SSID Broadcast: Disable
Username and Password changed to my own info
UPnP: Enable
I may have changed other things without knowing it. So like I said, a complete, step by step screen by screen set up would be totally appreciated. I haven't done anything in the security tab, all that is totally foreign to me, so I am just not broadcasting for now until I can get some help setting things up with you guys.
And if someone is familiar with the Laptop/XBOX 360 setup, and I need to change any of the settings on the XBOX itself, could you please include that in your directions? I know that isn't technically what THIS forum is for, but it would sure be helpful to me if you happen to know both parts anyways.
Thanks a lot (in advance)!So all you just need to do is, secure your Wireless Network. Follow the setps bellow and change the settings on your Router.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Wireless channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Now see if you can locate your Wireless Network and attempt to connect...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect... -
Using the WRT54G and a WUSB54GC with an Xbox 360.
Hi,
I have a WRT54G router and I just bought a WUSB54GC compact Wireless-G USB adapter because I thought I could connect it to my Xbox 360 to play games online. Is this possible? I've tried a few times, but I can't get it to work. I'm not too tech savvy but I'm guessing that it isn't supposed to work like that. Thanks in advance for the help.Hi
As far as my knowledge, if you want to use WUSB54GC you need to install its drivers, and that is not possible on X-box 360, in that case you can check if your X-box 360 is Wi-Fi enabled, if not you can use a special product i.e. WGA54G, Wireless-G Gamming Adapter, It's completely driver-free, so it works on any platform. Since there's no drivers to load, setup is a snap. It provides lag-free gaming with communication speeds up to 54Mbps when connected to other Wireless-G devices. It can also connect to Wireless-B (802.11b) devices and networks at 11Mbps. -
WRT54G wont work for both internet and xbox 360
I bought the Linksys WRT54G so I can play my Xbox 360 and be on the Internet at the same time. I am not using it wireless meaning that i do have ethernet cords plugged in for both my internet and my 360. When i play my 360 it kicks me off the internet and vice versa. Any help?
Access setup page....
Please click on the tab "Application and gaming" and click on sub
tab "Port range forwarding"
1) On the first line in Application box type in "Xbox", in start box
type in 88, in end box type in 88, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
2) On the second line in Application box type in "Xbox", in start box
type in 3074, in end box type in 3074, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
3) Now save the settings
4) Once you return to the setup page, click on the tab "Administration"
and disable the UPNP and save the settings.
5) Now assign the given ip address on your xbox
ip address :- 192.168.1.20
subnet mask :- 255.255.255.0
default gateway :- 192.168.1.1
Please assign the dns address on the xbox
primary dns :- 4.2.2.2
secondary dns :- 192.168.1.1
6) Please try to test your xbox live.
Maybe you are looking for
-
Use of Bar Codes in reports and fonts
Hi, I've copied Word fonts for the bar codes in the folder "Windows font "on mi pc. Then I opened a DESKI report and I used the same font in the report. I must repeat the same operation on all pc's in the company and on the Application Server where i
-
CHARM IBase & Component tables
Hi, I want to know the table names for Change Request (SDCR) & Urgnt Correction (SDHF). I want to capture IBase & Component in Work flow CHARM. Regards Praveen K
-
I'm on a page, click a link it goes to the site but then nothing. I have to refresh in order to see or do anything. Annoying when playing a game and worrying when trying to purchase something or pay bills.
-
Can I create pulse train above 167s?
I need to generate pulse train with pulse width longer than 167.7 sec. using card 7030/6030E. Can anybody help me? Thanks
-
if i delete photo shop express from my phone, will it also delete my fotos in revel? i think the two are linked. not sure.