Wrt54g as a wireless access point

alright i recently changed around my configuration with my wrt54g wireless router. I have made it into an access point which i was unaware is better. Im kinda new to the networking deal though it is what i want to do as a career and access points are new to me. so to the point of this post... when i make it an access point instead of the router i cannot access the admin setup page anymore. I know that when its the DHCP server you type in the default gateway that your given and the admin page pops up... well when its just an access point the gateway is from your router box not the linksys. so how if at all possible am i able to access the setup for the linksys if say i wanted to change the SSID of my network? i appreciate any help
Solved!
Go to Solution.

It depends. If you have another gateway router then you should assign a LAN IP address inside the gateway router LAN. For instance, if your gateway router uses 192.168.0.1/255.255.255.0 then you could assign a LAN IP address of 192.168.0.2/255.255.255.0, turn off the DHCP server and do the LAN-LAN connection.
If you only have a simple modem and the computers make a direct connection to your ISP then you have to set up a static IP address temporarily. Assuming you did not change the LAN IP address of the WRT from 192.168.1.1/255.255.255.0 you would assign a static IP address 192.168.1.2 with subnet mask 255.255.255.0 on the computer. With this static IP address the computer can access http://192.168.1.1/ After that you change the computer back to DHCP (Retrieve IP address automatically).

Similar Messages

How do I configure WRT54G as a wireless access point?

Ater a whole series of problems related to Vista, a WAP54G, Airport xpress, wireless printers, etc. plus at least three hours on the phone with Linksys tech support acessing my computer remotely and still not fixing the problems, I dumped my WRT54GC for a Belkin-N router. I set it up over the weekend and slowly regained internet access, then the pinter, then the Airports.
I still would like to have an access point because my signal strength even with the new N router is too weak downstairs to allow my PS3 to connect to it. I cannot figure out how to configure the WAP54G to make it work. I want to take a shot with the WRT54GC. From what I've read, I should be able to do it.
I can get into the router (referring to the Linksys) no problem. I can reconfigure it to an extent, changing the IP address to the recommended 192.168.1.2. I do this by running an ethernet cable from my PC to the router. Howver, after changing the IP address in the router I can't get into it any more using the new IP address. When I attach teh Linksys router to the Belkin I can't get in either.
Both the Linksys and the Belkin use 192.168.1.1 as the default IP address for each device.
I would like to know what settings I need to change i nteh WRT54G to turn it ino an access point -- an extenson of my existing network with teh Belkin router attached to the Comcast modem. I have looked at various how-to's and they all seem to assume I am connecting the two routers with an ethernet cable. If it's not clear at this point, I'd like to connect them wirelessly.
Thanks.

Thanks so much for the reply.
I was working with it all last night and somethign strange happened. After reading some other info on the internets, I changed the IP address on the WRT to 192.168.2.1. It updated, I then ran the wire from the Belkin to the WRT, I typed in 192.168.2.1, it took me to the Linksys setup page, but when I clicked "wireless" in the WRT setup, it took me to the Belkin setup page. How in the world did that happen?
Armed with tis new info, I did a hard reset on the WRT -- assuming it would change the WRT back to 192.168.1.1 -- got into the setup, turned off DHCP, left the IP as .1.1, and then wired it again into the Belkin. I can now get into the setup of either one.
Here's the thing: I don't want the two routers wired together. I want to move the WRT downstairs so a PS3 can pick up the signal. I want the WRT to wirelessly relay that signal to the Belkin to get the PS3 onto the net. I can't run a wire from the Belkin to the WRT.
I've read conflicting reports about whether the WRT can do this. Other sites suggest adding 3rd party firmware to add that functionality but that will definitely push the bounds of my abilities and likely exceed them. So, can the WRT even function in this way?
Inre the WAP, I don' know why but my ability to access the setup menu via 192.168.1.245 is very hit or miss -- much miss than hit. It makes no sense unless there is a bad connection somewhere because I hard reset, wire it to my laptop, put in the IP, and time out 19 times out of 20. I've got the MAC address for the router, and I think I know I want it to function as a repeater, but I've not been able to get that working right eihter.
Thanks for any further reply.

Using a WRT54G as a wireless access point with a WRT610N gateway router

I have just replaced my WRT54G gateway router with a WRT610N and everything is fine. However, I want to know if it is possible for me to use the old WRT54G as an access point/wireless bridge on a different floor to the gateway.. that is I want the WRT54G to connect wirelessly as a router to the WRT610N gateway router (not cabling them on the LAN ports) and then I want to use its LAN ports on the WRT54G for local cabled devices rather than use it as a wireless extender. I have read various post but most seem to suggest cabling between the routers.
Solved!
Go to Solution.

With Linksys firmware: no. Not possible. A Linksys wireless router won't operate as bridge. It won't connect wireless to other devices. You have to run a cable
With 3rd party firmware like dd-wrt or tomato: you can configure the router as wireless bridge or repeater. Please check the documentation of the 3rd party firmware to find out if your router model and version is compatible. Please remember, that a bridge or repeater with the WRT54G will slow down your whole wireless network.

Can WRT54G be setup as a Wireless Access Point?

Does anyone know how to setup a router (WRT54G) to connect to other routers using a wireless connection and function as either a wireless access point or another router using the main router for it's internet and network connection?

you cannot get the WRT to connect wireless to any device as it is an access point.
However this same thing will work wired. All you need to do is change the LAN ip of the WRT to 192.168.1.50 from 192.168.1.1 and disable the DHCP on the WRT.
Connect both devices LAN to LAN , do not use the internet port of the WRT.

How to setup a wrt54g router as a wireless access point to extend wifi signal from e3200

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
any tips to avoid interfearance once setup?

You have to connect both with a cable.

Using WRT54GR as a Wireless Access Point only

I have a WRT610N as my main router. I want to use an existing WRT54GR purely as a wireless access point and ethernet switch. Any suggestions on how best to do that so I can still access the WRT54GR to make configuration changes? Right now I have the network functionality working by simply not using the Internet port on the WRT54G but by going to 192.168.1.1 I can only get to the WRT610N.

(Restarting this thread).
I made the change you suggested and statically assigned 192.168.1.200 to the WRT54GR. I can reliably access it through this IP address. I connected it to the rest of my network by using one of the 4 switch ports (not the Internet port). I disabled DHCP on it and configured the Wireless settings to be the same (same SSID and Security Settings) as my other wireless router.
What I'm finding is that devices in my house won't assoicate with it. I tried changing the SSID to a different value; devices were able to see the new SSID but when I entered the pasword they told me that no DHCP server could be detected. A wired device that I plugged into another of the 4 switch ports on the WRT54GR was able to pick up an IP address from the main router just fine so I know that basic connectivity is OK.
To achieve what I want (i.e. the WRT54GR just acts as a wireless base station to extend wireless coverage in the house), do I need to connect the WRT54GR to the rest of the network using the Internet port rather than a switch port? If so, what configuration settings do I need to set up so that all the devices can get their IP address from the main router?

An Error Occurred while trying to join "my wireless access point"

Hi,
I've been using wireless access for a year and never had a problem connecting.
But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
I get the strange feeling that they planted some kind of bug/virus!!!
I don’t know what else to do.
Anyone knows that problem? What can I do?
Any help is greatly appreciated!
I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

Hello Tesserax,
I get the same error message again...
I tried the 3 suggested steps again, but unfortunately it did not work.
After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
Even if the Computer was asleep for just a second!
I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
And it works fine…until the screensaver comes on or it sleeps again
I have the Problem with my IMac and Mini but the IMac at least remembers my password…
Any Ideas
I’m connected through a Buffalo WZR2-G300N wireless router

Apple TV 2G (Airplay and Homesharing) can only stream from devices on the same wireless access point range??

connection:
40 Mbps Fiber Broadband connection using:
Devices:
1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
3. Wireless Repeater to cover a dead spot (AP3): Linksys/Cisco E1000 wireless repeater.
4. Apple Tv (AT2G) with home sharing/airplay enabled.
5.( Ipad) with home sharing on itunes enabled.
6. Win7 (PC) using iTunes with Home sharing enabled.
all devices are updated to their latest firmware.
In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
Am i the only one with this problem, would there be something wrong with my setup?
Your feedback is highly appreciated.

You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
I don't really follow your next point.
instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

Is it possible to remove the iphone history of wireless access points to which you've connected?

So.... I work in a place where there is a lot of security and snooping. There are folks specifically assigned to track down phones in unauthorized places. Their enthusiasm is sometimes annoying.
I leave my phone in a locker outside of the restricted area. However, I recently overheard some of the "snoops" discussing a phone that they had found. They were discussing a specific wireless access point that was in that phone's history, that caused some discussion. Although the phone was located in the locker area, they had apparently discovered it and examined it.
It was my phone.
One obvious course of action is to make sure the phone is always turned off (which I will do), but they have now identified my phone by the APs to which I connect, and I'd like to erase that history.
Is it possible?
Thank you.

Settings > General > Reset > Reset Network Settings.

IOS 6.0.1 - Problems with certificate based authentication on wireless access point

Hi all
We are using iPad 2 as order terminals in our shops for about 5 months. Some of the iPads (the first who entered the field) started to cause problems now. These iPads are no longer able to keep long-term connection to the wireless access point in our stores. After selecting the SSID a successful authentication using the stored EAP-TLS certificate is performed (this can be seen in the log files of our wireless controller and by the IP adress that is given by DHCP). But within seconds the affected iPads opening up a captive portal page (empty, without contents) and separates the connection to the SSID after a short time again.
Affected are currently only iPads 2 with iOS 6.0.1, which were staged about 5 months ago. The newer devices with iOS 6.1+ connect without problems and open no captive portal page. The first cases occurred on the last Wednesday. Before that everything worked without difficulty. No modifications took place on the security structure. The numbers of affected devices increased until all iOS 6.0.1 were affected.
Access to other SSIDs (without use of certificates, by entering a key) for the devices is still possible (the devices does not open an captive portal page). The DHCP scope is not used up, so there are enough IP addresses available.
"Newer iPads" with an iOS of 6.1+ are are showing no problems on the same wireless access point, where the older devices are rejected. New and old devices use the same certificates and authentication mechanisms.
In the analysis of the issue, it turned out that the problem can be solved by an update to iOS 6.1.3. Subsequently, the iPads will be able to rebuild a connection with the access point, without a captive portal page.
Since the bandwidth is very narrow dimensioned in our stores, the communication of the iPads was severely restricted. Thus, the iPads are for exampleare accessible for the APNS but can not find iOS updates or check for their availability.
A comprehensive update to iOS 6.1.3 is currently excluded.
Does anyone knows this issue? What else can be done (except from updating)?

I will answer my own question in case it helps anyone else.
It would "seem" the ios 6 devices try the proxy and if that is not working they resort to the def gateway.
To Fix I did the following:
Brocade WIFI network has IPS and Advanced Firewall rules that seemed to be tthwarting some traffic, the iphones would then try the default gateway and be blocked at the FW.
I disabled the IPS and the Advanced Firewall Settings on the wifi as they are redundant to our main IPS and firewall that all traffic flows through anyway. I will tune it later, but when the CEO is demanding a fix "**** the security, full speed ahead"
Created some rues on the firewall to allow...
- IMAP-SSL (port993) outbound
- SMTPS (port 465) to yahoo servers outbound
- tcp port 587 to yahoo servers outbound
- https to akamai servers
Most http and https goes through the proxy as it should, BUT...
It seems that the akamai traffic allways ignores the wifi proxy settings and just heads straight for the default gateway. I suspect there is a bug in the icloud app?
Hope this helps someone else.
-Bo

Wireless access point no longer working with ios7

Upgraded to ios7 and did not change anything. Wireless access point still recognised in settings however no internet connection possible. What's wrong or different with iOS 7?

1. Turn router or access point off for 30 seconds and on again.
2. Settings>General>Reset>Reset Network Settings.

N800 no longer detecting any wireless access point

The device is working fine couple days ago, then today when I turn it on, the "connection manager" can no longer see any wireless access point. Not only my home network, also
my neighbor's wlan. My laptop can detect 10 networks
around my house. I try upgrad my os to the latest version and it is still not working. Is anyone has similar experience ? Is it a hardware problem ? Any advice will be
welcome.

It happened to my N800 too just a couple of days ago after I installed a number of applications. I have already removed those applications but the N800 still would not detect the access points that it usually detects with no problem.
It could not detect the WLAN inside our house even if the N800 was physically sitting on top of the router. It would intermittently detect my neighbor's WLAN (the one which I usually use) but it would not log on to it.
I tried removing the battery hoping to reset it but nothing changed.
It also would not connect to my PC via USB. The computer could not detect it. This one happened even before I installed those applications.
Help!!!!

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

I can't get my macbook to access shared files on a windows computer when it's connected through a wireless access point.

I recently bought a Netgear Wireless Access Point to use in the office so we can have a wireless network. I configured the wireless network, and I am currently connected to the internet. However, I no longer can access the shared files on the Windows computers like I could when I was hardwired in with an ethernet cable. I've disabled all of the internal firewalls on all of the computers (and there's no firewall built into the WAP), all the computers are on the same workgroup, and I've tried accessing the computer with the shared files directly via the IP address using the instructions found here http://docs.info.apple.com/article.html?path=Mac/10.5/en/8849.html.
My computer sees that the other computers on the network are there. They show up in the network view from the finder. However, when I try to connect to them, it tells me the connection failed. When I click connect as, it says:
"Connection Failed
"The server “PC-ASSISTANT” may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again."
When I try to connect via the "connect to server" on the finder, I type in "smb://10.0.0.103/Word Processing" It tells me:
"There was an error connecting to the server “10.0.0.103”. Check the server name or IP address, and then try again.
If you are unable to resolve the problem contact your system administrator."
I have no clue what the problem is. I'm not really an IT person or a networking guru. Can someone please help?

You posted in the Older Hardware forum, which is for pre-year 2000 hardware. Suggest you post your question in the Airport forum at https://discussions.apple.com/community/wireless/airport
 Cheers, Tom

Wrt54g as a wireless access point

Similar Messages

Maybe you are looking for