WRT54G can''t connect to internet or 192.168.1.1

My router used to work. I updated the firmware to 4.21. xx and after that I can't connect to internet.
When I connect directly to modem, I can go to the internet . I power recycled etc but when I connect to the router, it says limited connectivity. It shows autoconfigurtion ip:169.254.251.135
I don't know why this is so.
I don't have the setup cd disk but I read the users' guide and it seems that I really don;t need the cd. But no matter what I do , I can't get to 192.168.1.1 .
Do I need a setup cd and where I can download?
Any help is appreciated.
Thanks ,
Sankar

Do the 30/30/30 Hard Reset and then check the IP address on that computer. For the reset steps do the following:
The following procedure will clear out the NVRAM and set Router back to default values:
With the unit powered on, press and hold the reset button on back of unit for 30 seconds
Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
Plug the unit back in STILL holding the reset button a final 30 seconds....
If still you are getting same IP address then try to reduce the LAN card speed. Here is the step:
START--> right-click My Network Places and click Properties
right-click on the device and click properties
Click on the CONFIGURE button
Select the ADVANCED tab and the settings you can alter are listed on the left.

Similar Messages

Can't connect to Internet and 192.168.1 network at the same time

I have been having an issue with my MacBook's networking for the past 4 months. Here are the specifics:
*My MacBook is connected to the Internet via a linux router, with an address in the 192.168.1.x address space. DNS server is an openDns server, 208.67.222.222
*My MacBook is assigned an IP Address manually in the 192.168.1.x namespace
*I have a printer manually assigned an address in the 192.168.1.x namespace
Problem:
* I can only connect to my printer if I leave my DNS server entry blank under my Airport TCP/IP configuration
* I can only connect to the Internet when my DNS server entry to set to the openDNS server entry.
Question:
Is there any way I can connect to both my local network printer and the Internet at the same time? I have set up two locations that I can switch between, but I would prefer to be able to access both networks at once.

I tried turning AppleTalk on, but no luck.
It seems that the problem is related to basic TCP/IP connectivity. For example, when my DNS server is set to blank, I get a fine response from the command "ping 192.168.1.253". However, when my DNS is set to one of the openDNS servers, I get this error:
PING 192.168.1.253 (192.168.1.253): 56 data bytes
ping: sendto: No route to host
ping: sendto: Host is down

Problem with my linksys WRT120N i can't connect to the address 192.168.1.1

Hello friends
i need help cuz i can't connect to the address 192.168.1.1
i didn't change the address 192.168.1.1 to an other address but i can't connect to this last i want to change my options
i really need help plz

Make sure that the computer is connected to the router on the Ethernet port..Now,check the ip address on the computer....Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,Adjust the Browser Settings on the computer....Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...

Can't Access Router Settings via 192.168.2.1

I have recently changed modem/routers as my connection speed was increased recently and the old modem wasn't up to the task... The previous modem/router was preconfigured and I did nothing to it, however the new one requires settings be fixed by accessing it via a browser at 192.168.2.1
When the technician came to check my line and set up the new modem, we encountered a strange situation. Despite being connected by Ethernet cable, my machine could not access the IP address reserved for the router.
The reply is: "Safari can’t connect to the server.
Safari can’t open the page “http://192.168.2.1/” because Safari can’t connect to the server “192.168.2.1”."
We tried Firefox and the same happened.
I have deactivated my firewall, rebooted, changed cables, restarted the router, got Safari to pretend to be Explorer, got the neighbor's dog to bark at it, everything except make a blood pact with the devil, and the two browsers on my machine think that 192.168.2.1 is an external address- which it isn't, and of course fails to connect.
The technician used his laptop to configure the thing, so I can access the internet (obviously) but I must find out why I can't access the router/modem's settings, if only to find some logical reason for this illogical behavior.
I've tried looking this issue up, and I get lots of bad wiring, wireless connection, windows proprietary shenanigans, but none that explain my situation.
I'd appreciate it if someone could help me make sense of this.
My setup:
Computer Model Name: Power Mac G4 (AGP graphics)
Model Identifier: PowerMac3,1
Processor Name: PowerPC G4 (3.3)
Processor Speed: 1.35 GHz
Number Of CPUs: 1
L2 Cache (per CPU): 256 KB
L3 Cache (per CPU): 2 MB
Memory: 832 MB
Bus Speed: 100 MHz
Boot ROM Version: 4.2.8f1
Sales Order Number: M7827LL/A
Router: "2-Wire Gateway"

Your advice did the job quite nicely and it seems this is the "natural way of things," but I was totally unaware of it since my previous modems were preconfigured and I never had to muck about with subnets and such things.
What irks me is that this is basic, bare bones information that the Tech support people should have given me right off the bat. Why do they assume I have all the right numbers input into the Ethernet or PPPoE settings? They seemed totally perplexed that I couldn't connect, and frankly so was I- since my old Mac, as decrepit as it is, is still able to kick it with the modern way of things better than most computers I work with.
If they had asked me if I had set the right IP's in the right slots, it could have been fixed in 2 minutes.
Thank you very much for solving my problem, it saves me a lot of stress and confusion.

Can't connect to Internet via Airport

I have a PPPOE ISP account. Before upgrade to Lepoard, just fine. Now I can only connect to internet using cable via my router moderm. I cannot connect my wireless router.
The wireless router will appear to be connected but it said self assigned IP. If I hardcode an IP eg. 192.168.11.2 to it. The Airport status will become connected but still cannot dial into my PPPOE account. An message no PPPOE service will appear. But if I plug in the LAN cable, everything work fine. Why this happen? My wireless router work fine with my Window XP and my Mac (before upgrade to Lepoard) What configuration should I change? I am an idot to networking. I have download all patch and has tried boot to safe mode etc.
Anyone can help?

By power downs do you mean Sleep?
One thing that might work is to set the IP to Static in Network>Configure IPv4>DHCP with Manual Address.

WRT54G v.1.1 can't get on my interface "192.168.1.1"

Hello, I'm having problems getting into my user interface, and I can't get on any website with my router connected, I try using 192.168.1.1 on internet i.e. and firebox. I also got my default IP through, ipconfig/ all and that did not work, I also try to renewed my IP with ipconfig/renew, no go. All my connections are the way they should be, I even try connecting my router by itself to my PC change the IP address and nothing. Can't someone please help, my router was working when I first plug it but I forgot my wep security and press the reset button on the back and that's when everything started to fail..............

As you want to Upgrade your router's firmware you can try the TFTP Utility...
Download TFTP Utility 36.0 KB...
Download Firmware 2.95 MB...
Double click the TFTP.exe file and click run :
For Server- Enter the IP Address of the router that you assigned. By default, the router is 192.168.1.1...
For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
For File- Click the triple “…” button and browse for the .bin firmware file...
Click Upgrade button to start upgrading. A progress bar should show up to show the progress.
Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Adobe cloud application manager - can not connect to internet

To ADOBE - The Adode cloud Order no is DSSY006786009DT and is current
The Adobe cloud application manager - can not connect to internet even though there is internet connection and says it might be time zone error but that is correct - Sydney Australia
Question:
1. Is anybody else having this problem
2. How do we fix
I already changed the time zone east coast US - did not change anything
Could it be a corrupt program - thus requiring to reinstall program Application manager
I am using Windows 7.
It has been like it for ten days - It asks to log in everytime I turn computer on
All programs in Creative Cloud work
Any suggestions and solution
Online help and phone help had no solutions other than what I suggested - that is reload application manager
Thanks for help
Ian Cleland

The Creative Cloud File Synching was just offline, should be online now again.
See top off: http://forums.adobe.com/community/creative_cloud/creative_cloud_connection
Maybe that was your problem.

Just got new ipad2 and can't connect to internet...recognizes wifi network but won't connect

just got a new ipad2...recognizes wifi network at home, but can't connect to internet...help???

I just had a similar problem. Both the ipad 1 and ipad 2 in my household quit connecting to the network even though it seemed to recognize it. if you think it is recognizing your network, just not connecting, check to see if bluetooth is turned on. i had to turn bluetooth off and then manually enter the DNS number.
My solution also came after I re-started my network and reset all the settings on the ipad2. The DNS number then showed along with IP submet Mask and router. I used that dns number to enter into ipad1 after turning bluetooth off on it.
Totally unscientific fix that may have been more coincidental than correct but you might try it. BTW--no idea how bluetooth even got turned on to begin with.

Ipad2 -can i connect to internet using a data card

ipad2 -can i connect to internet using a data card

This article:
http://edcommunity.apple.com/ali/story.php?itemID=18585&version=6330&pageID=1582 9
depending on your experience level should tell you all you need to know.
You don't need mobile me, you just need to know your mac's ip and have vnc
client software of some sort running on the machine you are travelling with.
Read the entire article, as once you get past the part about monitoring multiple machines there is some useful info.

Can't connect to internet on my old g4 flat screen, network + airport ok

I installed an airport card on the g4 (dome) and connected to our wireless network, which gets a signal, (though the status is "not available"). I can't connect to internet (server not recognized), and every time I check the internet assistant app, the setting has been changed back to modem. The router is in the basement: my iMac is on the first floor and works fine, the g4 is on the second floor. Is that too far away? Do I need to update the g4? Two minis also work fine, one on first floor and one in basement. Any help appreciated.

Which iMac G4 do you have? Some iMac G4s are 802.11b while the later ones were 802.11b/g.
If your wireless network is configured for "802.11g only", the older 802.11b iMac G4 won't be able to connect.
If your wireless network is configured for "802.11n only", the iMac G4 won't be able to connect since it isn't compatible with that.

Can't connect to Internet on my ipad

Can't connect to Internet on my ipad I've tried everything nothing is working. All my other electronic s are working except the ipad help

I don't know what you mean by "everything", but here is a comprehensive Wi-Fi troubleshooting guide:
http://www.apple.com/support/ipad/wifi/

IPhone 5 and 5c can't connect to Internet every 1 or 2 days with iOS 8.0.2

After having upgraded my iPhone 5 and my wife's iPhone 5c to iOS 8.0.2, they both can't connect to Internet every 1 or 2 days.
They can't connect via wifi neither via 3G.
If I restart the devices they start to connect again.
I tried to reset the network settings and also to restore the devices from scratch via iTunes like the Apple support suggested me, but the issue still persists.
I'm very frustrated also because I bought to my wife an iPhone telling her she wouldn't have had all the issues she used to have on a previous Samsung smartphone...
Anyone has having the same issue?

After the update, try resetting your cellular network settings on the phone. Make sure the airplane setting is correct and try shutting it on and off to see if that works.
See if that helps.
Good Luck!

After i update my ipad 2(wifi 3g/64g) to ios 5.0.1..everything works ok except 3g can not connect to internet.. in the top of my ipad screen it show 3g sign..before update the 3g was working ok

after i update my ipad 2(wifi+3g/64g) to ios 5.0.1..everything works ok except 3g can not connect to internet.. in the top of my ipad screen it show 3g sign..before update the 3g was working ok

i am at SAUDI ARABIA and the Service Provider is (STC) i found that the APN setting has to change from (jawalnet.com.sa ) to (afaqwireless.com).. NOW 3G OK

5 out of 6 devices can't connect to Internet

Just to preface, this was all working hours ago.
airport express, Mac book pro, ipad, boxee box and Western digital live Nas all can't connect to internet.
my Samsung Galaxy s3 has no problems however.
normally if I can't get an ip address I would just say the Internet is down from the isp. But because I've got one device where it's working fine gives me cause to think otherwise.
Any ideas would be greatly appreciated.

You want the device that is directly connected to the modem to furnish the PPPoE service.
This is sounding like you had your Mac connected directly to your modem at one time, so in that type of setup, the PPPoE connection on the Mac would have been correct.
But, since you have added the Time Capsule....and it is now the device that is directly connected to the modem.... the Time Capsule must be configured to provide the PPPoE connection service, not your Mac.
Open AirPort Utility - Click Manual Setup
Click the Internet icon
Your settings should look like this:
Connect Using = PPPoE
Account Name = Your user name with your ISP
Password = Your password with the ISP
Verify Password
Service Name.....leave this area completely blank
Connection = Always On
Disconnect if Idle = Never
Update to save settings and the TC will restart
Either delete the PPPoE connection on your Mac, or if you want to retain it in case you need to connect your Mac directly to the modem at some point in the future, make that connection inactive.
If you are connecting an Ethernet cable from one of the LAN <-> ports on the TC to your Mac, you want the Ethernet connection to be active on your Mac. This should happen automatically if the PPPoE connection is inactive or has been deleted.
Be sure to power cycle the entire network at this point. Power all devices down, or der is not important.
Wait a moment or two, then start the modem and let it urn for a moment by itself
Start the TC and wait for a green light
Then start each device one at a time until the network is back up

Can't connect to Internet after sleep mode

Hi,
Most times after put my iBook in sleep mode and reopen it, I can't connect to Internet. I use a normal cable connection by ethernet, but at these times, when I check the network status, it says I don't have any cable connected. The modem apears to be OK, with the computer's light on. I plug off and plug in the cable and it doesn't change and it happens the same when I click in DHCP renew - it just doesn't give any IP adreess. I need to restart the computer to get the connection again.
Ibook G3 700 Mac OS X (10.4.7)

I am trying other solutions today.
It can not change to another wifi network without switch off the wifi.
That's mean I have switch off and re-open the wifi signal every time when it show like this capture.
I waiting for more than 5 mins and it will search another wifi network automatically but it still "No internet connect".
My MacBook Pro is no any WiFi issues.

WRT54G can''t connect to internet or 192.168.1.1

Similar Messages

Maybe you are looking for