Wrt54g cant get on internet after connecting dsl to router

i have been trying to get this this thing working all day. ive tried everything. dsl works fine when hooked directly to the tower but as soon as i connect to the wireless router i cant get the connection? i ve tried everything including turning firewalls off and everything. please help me thanks

when you hard wire the tower to the router does the tower have a conection then?

Similar Messages

HT1369 i cant get my ipod to connect to itunes or my laptop

i cant get my ipod to connect to my laptop or itunes i have unistalled and reistalled itunes but this doesnt help at all

Hello, waynemclno1.
Thank you for the question. Try the steps in the article below to troubleshoot your iPod touch not being recognized in iTunes. I would recommend seeing the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Cheers,
Jason H.

HT3140 put a date 1970 june 27 . and now the whole system is out of control i cant get to internet cannot change date and time always when i opened system preferences stays in a waiting mode but doesnt show any opcion don t know what to do and i just bou

put a date 1970 june 27 . and now the whole system is out of control i cant get to internet cannot change date and time always when i opened system preferences stays in a waiting mode but doesnt show any opcion don t know what to do and i just bought this computer

It may well be a driver issue but considering the loading: Xorg trying to load different drivers is somewhat normal. @cafe you can see that these are autoconfigured by X above the loading in the log:
Jul 20 19:48:24 arch gdm-Xorg-:0[216]: (==) Matched intel as autoconfigured driver 0
Jul 20 19:48:24 arch gdm-Xorg-:0[216]: (==) Matched intel as autoconfigured driver 1
Jul 20 19:48:24 arch gdm-Xorg-:0[216]: (==) Matched modesetting as autoconfigured driver 2
Jul 20 19:48:24 arch gdm-Xorg-:0[216]: (==) Matched fbdev as autoconfigured driver 3
Jul 20 19:48:24 arch gdm-Xorg-:0[216]: (==) Matched vesa as autoconfigured driver 4
As long as one of the drivers gets loaded, which it apparently does the failing of the others is fine.
Was there an update maybe ?

I cant get the internet on the i phone 5

I CANT GET THE INTERNET ON THE I PHONE 5

Vague.
Please explain your issue in much more detail than "CANT GET THE INTERNET" adn please stop shouting at us.
All caps indicates shouting, is considered rude, and is difficult to read

MOVED: [nForce] K7N2 D2-FSR cant get in window after manual setting

This topic has been moved to Overclockers & Modding Corner.
[nForce] K7N2 D2-FSR cant get in window after manual setting

I'm a bit of a noob at o/c so not sure I can give you sound advice.
pci is unlocked I think, though if use core centre then you can control it-I'm not using corecentre.
are you using priority 10 for prime 95 and In-place FFT's torture test? I believe that is most demanding. If you getting reboots then you're overclock is not stable, need to lower fsb and retest. Your psu is probably marginal as well so maybe that isn't quite strong enough to be pushed further. Can you try beefier one?
I don't know how far you can push vcore up; maybe one of our resident experts can advice.
I started out on this journey with exact problem you faced; I couldn't change High Performance mode from optimised to manual. I still haven't found a solution unless I enable DOT. I've tried bios b5, b6.1 and now trying b6.0, without success. O/S fails to load. Did you say b3 allowed you do to that and increase fsb in bios or was it change of memory? I'm thinking my expensive ram is not very flexible and doesn't suit the nforce 2 chipset. At moment with bios b60, high performance manual, memory to manual (2-2-2-11) and DOT enabled-private I passed memtest overnight. I'll try prime95 tonight if I have no issues tday.
Dave

I am a proud owner of iphone5, iOS6.1.4, recently I am facing prob to connect it with Ford Figo. Its not that iphone is not connecting, its getting disconnecting immediately after connected. I hv tired other ph with car, its working fine, how 2 resolve ?

I am a proud owner of iphone5, iOS6.1.4, recently I am facing prob to connect it with Ford Figo. Its not that iphone is not connecting, its getting disconnecting immediately after connected. I hv tired other ph with same car, its working fine, how 2 resolve ?

Morning Indrajit Chatterjee,
Thanks for using Apple Support Communities.
For more information on this, take a look at this article:
iOS: Troubleshooting car stereo connections
http://support.apple.com/kb/TS3581
Best of luck,
Mario

[nForce] K7N2 D2-FSR cant get in window after manual setting

hi there,
i m a new guy here, not very good in english!!
before i send this, i had look some of the guide.
but cant find people with the same problem as me.
the problem is i cant get in window after set my High Perfomance Mode to MANUAL in cell menu.
nothing change just Optimized to Manual.
if access in, still will freeze after few second.
everything is fine with Optimized Mode, no error in Prime 95 for 9 hours.
hope can get some HELP from you all.
i also using core cell, will my setting in Bios appear same in core center???
example: 210 FSB in bios = 210 FSB in core center.
i hope to hear from you all soon.
10x.

I'm a bit of a noob at o/c so not sure I can give you sound advice.
pci is unlocked I think, though if use core centre then you can control it-I'm not using corecentre.
are you using priority 10 for prime 95 and In-place FFT's torture test? I believe that is most demanding. If you getting reboots then you're overclock is not stable, need to lower fsb and retest. Your psu is probably marginal as well so maybe that isn't quite strong enough to be pushed further. Can you try beefier one?
I don't know how far you can push vcore up; maybe one of our resident experts can advice.
I started out on this journey with exact problem you faced; I couldn't change High Performance mode from optimised to manual. I still haven't found a solution unless I enable DOT. I've tried bios b5, b6.1 and now trying b6.0, without success. O/S fails to load. Did you say b3 allowed you do to that and increase fsb in bios or was it change of memory? I'm thinking my expensive ram is not very flexible and doesn't suit the nforce 2 chipset. At moment with bios b60, high performance manual, memory to manual (2-2-2-11) and DOT enabled-private I passed memtest overnight. I'll try prime95 tonight if I have no issues tday.
Dave

WRT54G ver 2 - Shows Im connected to wireless but cant get on internet

I just moved into a new apartment and am having trouble getting my wireless router to work. I just got my cable internet set up and can get on with the modem fine but cant get the wireless to work so my roommate can get online. I think i was able to get online when i had the modem connected to the router with a ethernet cord going from router to computer but cant even get that now. I tried some of the FAQ guides like "setting up a router with cable internet' and 'seting up wirless settings on a linksys router" and cloning my MAC and downloading new firmwear for the router but still no luck.
Everything worked fine a couple days ago at my old house. When i search for wirless networks on my mac I see my linksys and it has full connection. When i go to it it shows green lights for ethernet,network settings and ISP but internet and Server are red. I would really like to get wireless internet up so me and my roommate dont have to share the modem tonight so any help would be greatly appreciated.

Bypass the router and connect the computer directly to the modem. Make sure that you can access the Internet through the modem.
Connect the modem to the Internet port and the same computer to Ethernet port 1 on the router.
Check the lights on the router. You will see Power, Port 1, Wireless and Internet lights on the router.
Turn OFF the Airport on your computer.
Press and hold the reset button on your router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router and restart your computer.
Open the internet browser and in the address bar type http://192.168.1.1 and log in to the router setup page.
Go to MAC address clone sub tab. Enable the MAC address clone and click on Clone my PC's MAC. Save the settings.
Unplug the power to the router and modem. First plug in the power to the modem. Wait for 1 minute and then plug in the power to the router. Wait for a minute and then try to access the Internet on your computer.
If you are still not able to access the Internet then open the setup page of the router again and check the Internet IP address on the status page.
If you are not getting Internet IP address then router and modem are not communicating with each other.

I cant get my ipod to connect to my home internet.. what all should i do??

i cant get my iopd touch to connect to my home internet.. what should i be doing to fix that?

- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Setings.
-iOS: Troubleshooting Wi-Fi networks and connections

I have a ipod touch 3rd generation, I cant seem to get it connected to the internet, it connects to the router but not the internet ?? can any one help please?

i recently got an ipod touch 3rd generation, i cannot seem to get it connected to the internet... it connects to the router but cannot seem to get connected to the internet, it seems to connect to the router for a very short while and then suddenly disconnect again, i have tried various solutions but cant seem to solve it, this seems to be a common problem as i have seen many complaints on other forums, many say it may be the dns server . please can any one help?

Tap Settings / General / Reset / Reset Network Settings.
See if that helps.
If not try the iPod touch - Wi-Fi Troubleshooting Assistant.

I CANT GET MY MAC TO CONNECT TO THE INTERNET

I just bought a Mac book pro and am having trouble getting it to connect to the internet

Linc Davis may be right. However, how are you trying to connect? wirelessly or via Ethernet? Usually most Mac book pro's are not setup beforehand to connect to the Internet via your modem or router, or whatever you have. Check with your ISP for your settings, or see if your macbook pro is setup for Wifi (Apple-->Prefs-->network Pane) and have it try and find a wireless network of some kind. Failing that, try and set up your own wireless network, and do what Mr. Davis suggested too
J.B

Cant get any internet with my E1000

Hello, I bought a E1000 yesterday but I can´t seem to get any internet to any computer in the house.
First I ran the installation CD and everything went good untill the router were suppose to connect to the internet. So I restarted the modem waited over 2min and booted it again, but still nothing worked. (I have repeated this many times) So I then turned to the router. The router were getting a internet IP from my moden and all the lights were on too. So I started to look in the configuration. The DHCP Server was avalible and the Automatic Configuration - DHCP were chosen like it´s suppose to be. So everything looked fine in the router too.
I then looked to my computer, was it getting an IP from the router?
Yes everything was like it were on my WRT54G.
Anyone got a clue what might be wrong?
And I cant ping goolge.

Still the same..
Router:
        Firmware Version:    2.1.01 build 5Dec 3, 2010
       Firmware Verification:    adaa94b6f74ea9108084fc2b17c8d484
       Current Time:    Not Available
       Internet MAC Address:    98:FC:11:8E:3E:13
       Host Name:
       Domain Name:
        Internet Connection
       Connection Type:    Automatic Configuration - DHCP
       Internet IP Address:    81.230.148.140
       Subnet Mask:    255.255.255.0
       Default Gateway:    81.230.148.1
       DNS1:    195.67.199.6
       DNS2:    195.67.199.7
       DNS3:
       MTU:    1500
       DHCP Lease Time:    20 Min
Ipconfig:
       Link-local IPv6 Address: fe89::1183:7971:b78e:2992%10
       IPv4 Address: 192.168.1.100
       Subnet Mask: 255.255.255.0
       Default Gateway 81.230.148.1
       192.168.1.1

Im having trouble getting my wifi, it connects to the router but isnt getting internet. My room mates and I can connect our iphones and other devices just fine, help would be appriciated

First time on here and my knowledge with networking and such is very limited, my Mac Pro can connect to the router but when I try to open my browser it wont bring up any webpage. The only way I can get internet is through an ethernet port, Im basically at a loss for what to do.

You will find the AirPort icon (looks like this ) on the OS X menu bar. Option (or right) click the icon, and you should be greeted with a drop-down menu. All of the parameters I mentioned should now appear after the name of your Wi-Fi network.
The meaning of each of the values are as follows:
PHY Mode = The radio mode that your Mac Pro is connecting with.
Channel = The radio channel the Mac Pro is connected to.
RSSI = Received Signal Strength Indication. It's an indication of the power level of the signal as preceived by the Mac Pro's internal Wi-Fi antenna. Typically the higher the RSSI number the stronger the signal. RSSI is measured in arbitrary units. Some manufacterers use a positive scale, others like Apple, use a negative (0 to -100) instead. For the AirPorts, the less negative the better.
Transmit Rate = Instantaneous maximum date transfer rate of the connection in Mbps (Megabits per second)
MCX Index = Modulation and Coding Scheme. The MCS value identifies a number of things, including the number of spatial streams used in the Wi-Fi connection between the Mac Pro and the AirPort router. A larger or smaller MCS value is meaningless. Instead, it defines the actual connection type. In turn, the type can play a significantly on the potential bandwidth performance.

(VPN) There is no internet after connection established.

Hi Guys,
Mission: PC-1 in country X would like to use the internet(browsing, using his IP-->) of PC-2 in country Y.
Stage: on PC-2 i created "new incoming connection trough the internet" (VPN server) and on PC-1 i set up VPN client with (PPTP). The connection was established, i could browse even shared folder between PC-1 to PC-2,
BUT: on PC-1 after connected to VPN there was no internet, only file shareing, could not ping the PC-2 Ip, only the PC-2's VPN server. i spent hours checking settings, playing with IPs, route tables, but nothing worked.
i need assistant, what i did forgot or how can i accomplish my mission other way.
P.S in many cases i saw people on Client (PC-1) only unchecked "Use default gateway on remote network".. yes but than its use PC-1 ISP's internet.. but thats what i dont want .. i want to use PC-2's ISP internet...
Please help.

Hi,
This issue may occur if you configure the VPN connection to use the default gateway on the remote network. This setting overrides the default gateway settings that you specify in your Transmission Control Protocol/Internet Protocol (TCP/IP) settings.
Please refer to this fix:
https://support.microsoft.com/kb/317025?wa=wsignin1.0
Karen Hu
TechNet Community Support

HT1535 I cant get my iphone to connect to itunes.

I have had my iphone for a week, it synced once and now I cant get it to connect to itunes. My 3 sons ipods also wont connect.

See Devices Here > http://www.apple.com/support/itunes/

Wrt54g cant get on internet after connecting dsl to router

Similar Messages

Maybe you are looking for