WRT54G MAC doesn't match sticker
I recently bought this wireless router, & was recording information today. I noticed that the MAC listed on the sticker on the bottom of the router doesn't match the MAC listed in the "Status" section of the web interface. Which is the MAC that I should record as the correct one for the router? & could I have possibly made an input error that could have brought about this change?
(I am not using the "MAC clone" option. I have it as "Disabled".)
Message Edited by Skull6 on 03-24-2008 08:13 PM
The firmware should show the correct MAC address for the router.
Your router has two MAC addresses, one for the WAN port, and one for the wireless LAN. Usually these MAC addresses are the same except for a difference of 1. For example, one MAC address might end in 7, and the other end in 8.
If you clone a MAC address, and then set the "clone MAC address" back to "disabled", I am not certain whether or not this returns your MAC address to its original value. If the MAC address of your router matches your computer, then simply reset the router to factory defaults to get back the original MAC address.
Message Edited by toomanydonuts on 03-25-2008 04:34 AM
Similar Messages
-
Are all Intel 24" iMacs w/Snow Leopard OK for Mountain Lion? My serial number doesn't match any of the one in the iMac ID list; they all start with "MA" or "MB" and mine starts with a "W." Purchased direct from Apple August 2007.
Macs that can be upgraded to OS X Mountain Lion
iMac (Mid 2007 or newer)
MacBook (Late 2008 Aluminum, or Early 2009 or newer)
MacBook Pro (Mid/Late 2007 or newer)
MacBook Air (Late 2008 or newer)
Mac mini (Early 2009 or newer)
Mac Pro (Early 2008 or newer)
Xserve (Early 2009)
Open System Profiler and report what you find displayed for the Model Identifier. -
I want to email a photo through iPhoto but it says I need a password... I entered my password but it says it doesn't match - what password do they want and how do I fix? (Facebook and other social media iPhoto posts work - just email asking for password)
Your email password.
iPhoto '11: Email your photos
Open Mac Mail. From the Mac Mail menu bar click Mail > Preferences then select the General tab.
Make a selection from the: Default email reader pop up menu. -
My coverflow art doesn't match my video viewer. In my computer iTune>album artwork, I have two folders- download & local. They look close but are not the same. I think that is my problem, so which one of the folders do I use to overwrite the other?
ThanksDoes this happen in iTunes, on the iPod, one or the other, or both?
If the album art is correct in iTunes, try the steps listed here...
btabz: My songs have artwork in iTunes, but it won't transfer to my iPod!
Note: The above tip was written for iTunes for windows. Some of the instructions may be incorrect on Mac OS X. For example, to access preferences in iTunes, go to iTunes-->preferences, not edit-->preferences.
btabz -
Sometimes the artwork displayed doesn't match the track being played ... any clues as to fax or as to a why?
ThanksDoes this happen in iTunes, on the iPod, one or the other, or both?
If the album art is correct in iTunes, try the steps listed here...
btabz: My songs have artwork in iTunes, but it won't transfer to my iPod!
Note: The above tip was written for iTunes for windows. Some of the instructions may be incorrect on Mac OS X. For example, to access preferences in iTunes, go to iTunes-->preferences, not edit-->preferences.
btabz -
My Mac doesn't detect my windows DVD for bootcamp, help?
hi , i just grab my Windows 7 DVD for installing windows on Mac using bootcamp , but my mac doesn't detect my windows installation disc in boot menu... how to resolve?
You're not alone - I'm installed Windows (8 Pro 64-bit) on a MacBook Air Mid 2013 yesterday from the OEM/system builder media, and Boot Camp Assistant 5.0.4 didn't recognize the DVD. It asked for an .iso disk image instead, and I created one in a UNIX geek way**, but if you're an average mac user, you'll want to create one using the Disk Utility:
1) Open the Disk Utility. This is in the Utilities folder (go to a finder window and type command-shift-u)
2) Click on your DVD to select it.
3) In the File menu, select New -> Disk Image from "HRM_CCSA_X64FRE_EN-US_DV5"… (or your Windows disk title)
4) In the Save sheet, select Image Format: DVD/CD master. The Disk Utility saves this with the file extension/type .cdr, but this is the same file format as .iso. When the Disk Utility has finished, find the file you save and change the file extension to .iso.
5) Launch Boot Camp Assistant and select the .iso file as the source of your Windows installation.
Since I have a MacBook Air, the windows source was copied by the Boot Camp Assistant to a USB flash drive. MacOS X restarted and Windows was installed automatically, but the Boot Camp driver installer wasn't automatically launched at the end of the Windows install. I opened the flash drive's BootCamp folder and double clicked setup.exe.
Voila! The best trackpad anywhere! Network! Sound! Brightness control from the keyboard! The best Windows 8 computer!
** In Terminal: diskutil list; diskutil unmount /Volumes/HRM_CCSA_X64FRE_EN-US_DV5; sudo dd if=/dev/disk2 of=win8pro.iso. Use the output of 'diskutil list' to match your Windows 8 CD/DVD to a disk# for the 'dd' command. Be very careful. -
and need the new iTunes 11.1 to be able to use my iPhone on iTunes but I need the new mac software update OXS 10.6.8, but my mac doesn't need or have an update what should I do! I'm upset :'(
The requirements for iTunes:
Macintosh System Requirements
Mac computer with an Intel Core processor
OS X version 10.6.8 or later
400MB of available disk space
Broadband Internet connection to use the iTunes Store
Your Mac must be able to run OSX 10.6.8. If you can run that OSX then you can run iTunes 11.1.
Which Mac do you have?
MJ -
How do I pair a bluetooth headset when my MAC doesn't recognize it? The hedset work properly because they are paired with my iPhone. The headset is not an Apple product. It'd 3rd party.
Ask the headset manufacturer.
Barry -
Closing Stock Valuation doesn't matched physicallly
Hi SAP Gurus.,
Can you please assist me reg this issue"Closing Stock Valuation doesn't matched physicallly".
May I know the possible rectification ways to solve this problem.
Thanks in Advance,
Regards,
Balaji BhonslePhysical Inventory...
http://www.sap-img.com/materials/physical-inventory-process.htm -
After upgrading to Yosemite my mac doesn't shut off. The off button doesn't work
After upgrading to Yosemite, my mac doesn't shut off. The off button no longer works. I want to shut the thing off.
Jehreth,
On my Macbook Pro you have to hold the power button down a moment till a little window pops up and asks what you would like to do. Also you can go to:
( ) Menu > Shut down ...
to shutdown your Mac. Or are you saying that these options do not work?
Hope that helps,
Weston
Supporting article,
OS X Yosemite: Log out, sleep, restart, and shut down -
ICal on the Mac doesn't sync to iPad and iPhone
I'm syncing using iCloud. A calendar update on the iPhone will sync in iTunes but the sync only updates the iPad calendar. iCal on the Mac doesn't update to the newer iPhone calendar events. I also tried it by hooking the iPad directly to the Mac via the cable, and the newer events on the iPad calendar (which had the new events transferred via sync from the iPhone) didn't transfer to iCal. On the Mac in iTunes, I have the calendar named "Home" checked, which is the same name as the calendars on the iPhone and iPad.
How do you sync the Mac iCal to the iPhone and iPad calendars?The 'Home' calendar does not sync to iCloud, only the iCloud calendar does that.
In the iCloud control panel have you turned calendar sync on? and are you seeing the iCloud calendar in iCal?, all calendars in the 'On my Mac' group are local, they do not sync.
Also, check in iCal>Preferences>Accounts, to ensure that iCloud is subscribed to in iCal: -
I recently bought iphone 5 32gb white. Was surprise to see the outer box serial no doesn't match with iphone 5 system.
They have print XXXXXXTXXXX on box and on phone its XXXXXX7XXXXXX. Only one latter is mixprint though.
I check coverage status at apple site. The box serieal no is not found in apple system while the iphone 5 inside serial no i can see warrenty.
plz help is it normal to have serial no unmatched on phone and box or the phone is not genuineYou are correct. The SIM Tray of iPhone 5 does not have the Serial # printed on it. So your Serial # is the one in the Settings app About. This is your true Serial #. A 7 and a T from a box label are not distinct enough to matter. Apple will only honor the Settings About Serial # and the ones located inside the iPhone 5, which will be the same as the About Serial #.
-
Itunes will no longer accept any of my credit cards. It says vcode doesn't match when it does. Customer service is no help. I have re-inputted the info in the account section of the apple store and in itunes--still says vcode doesn't match.
Itunes will no longer accept any of my credit cards. It says vcode doesn't match when it does. Customer service is no help. I have re-inputted the info in the account section of the apple store and in itunes--still says vcode doesn't match.
-
Error: The decapsulated inner packet doesn't match the negotiated policy in the SA
I upgraded my ASA from 8.2(1) to 8.4(3) as I wanted to try to get Android devices to properly connect via VPN.
After some effort, I was able to get the Android devices to connect via VPN. However, my syslog server has a number of errors recorded that look this this:
%ASA-4-402116: IPSEC: Received an ESP packet (SPI= 0x1E76EFA6, sequence number= 0x1F0) from x.x.x.x (user= testuser) to y.y.y.y. The decapsulated inner packet doesn't match the negotiated policy in the SA. The packet specifies its destination as z.z.z.z, its source as a.a.a.a, and its protocol as tcp. The SA specifies its local proxy as y.y.y.y/255.255.255.255/udp/42246 and its remote_proxy as x.x.x.x/255.255.255.255/udp/0.
Digging further, it seems this error might be due to a NAT issues with the VPN connections. VPN previously worked with Cisco's VPN client on Windows, though I did not test to see if that is no longer working. However, I made no changes in the config, except for those related to additions needed to support L2TP. With the below config, Android clients can connect to the ASA and access the internal network, but they cannot connect to external addresses. I'm at a loss.
The addresses used in the config: 192.168.1.0/24 are on the internal LAN and 192.168.3.0/24 are addresses assigned to VPN clients.
I noted in the config this line:
access-list inside_nat0_outbound extended permit ip any 192.168.3.0 255.255.255.0
The access list is not referenced anywhere, though it was referenced in the 8.2(1) config like this:
nat (inside) 0 access-list inside_nat0_outbound
I'm not sure what else changed, but I've looked over the config and I just cannot see what the issue might be. I'm hoping somebody might be able to point out my error.
Here's the config file (at least the parts that might be of interest):
: Saved
ASA Version 8.4(3)
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
boot system disk0:/asa843-k8.bin
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_access_in extended permit icmp any interface outside time-exceeded
access-list outside_access_in extended permit icmp any interface outside echo-reply
access-list outside_access_in extended permit icmp any interface outside unreachable
access-list outside_mpc extended permit ip any interface outside
access-list inside_mpc extended permit ip 192.168.1.0 255.255.255.0 any
access-list testVPN_splitTunnelAcl extended permit ip 192.168.1.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip any 192.168.3.0 255.255.255.0
ip local pool VPN-Pool-1 192.168.3.1-192.168.3.254 mask 255.255.255.0
ip verify reverse-path interface outside
nat (inside,any) source static any any destination static obj-192.168.3.0 obj-192.168.3.0 no-proxy-arp
object network obj-192.168.3.0
nat (outside,outside) dynamic interface
object network obj_any
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP mode transport
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 10 set ikev1 transform-set ESP-AES-128-SHA-TRANSP ESP-3DES-SHA-TRANSP
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy testVPN internal
group-policy testVPN attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value testVPN_splitTunnelAcl
default-domain value test.us
group-policy testVPNnsl2tp internal
group-policy testVPNnsl2tp attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol l2tp-ipsec
group-policy testVPNns internal
group-policy testVPNns attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol ikev1
username testuser password PASSWORD encrypted privilege 15
username testuser2 password PASSWORD nt-encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group testVPN type remote-access
tunnel-group testVPN general-attributes
address-pool VPN-Pool-1
default-group-policy testVPN
tunnel-group testVPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNns type remote-access
tunnel-group testVPNns general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNns
tunnel-group testVPNns ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNnsl2tp type remote-access
tunnel-group testVPNnsl2tp general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group testVPNnsl2tp ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNnsl2tp ppp-attributes
authentication ms-chap-v2
One last question: in order to get the connection from Android to work, I was forced to use "tunnel-group DefaultRAGroup". Is that actually a limitation, or did I make an error that forced that requirement? I wanted to use "tunnel-group testVPNnsl2tp".
Thanks!Chris,
This is still a bit off the mark. I think I might be confusing the issue by including some of the VPN configuration that I had previously installed and working (e.g., two other VPN tunnel groups with split tunneling on one of them). Let's just remove that stuff from consideration. I actually tested the current configs just to see if they are working since the upgrade. testVPN is working with the split tunneling, but testVPNns (no-split tunneling) does not allow external access. I guess there is a NAT config issue there, too, but not sure what it is, yet. I've not investigated that closely.
I want to solve one problem at a time, though I understand there are some interdependencies.
What I'd like to focus on right now is just the L2TP VPN connection.
From what I've been able to understand from the documentation, what I need are these lines:
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP mode transport
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 10 set ikev1 transform-set ESP-AES-128-SHA-TRANSP ESP-3DES-SHA-TRANSP
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
group-policy testVPNnsl2tp internal
group-policy testVPNnsl2tp attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol l2tp-ipsec
tunnel-group DefaultRAGroup general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key P74bmqL6rT40bl5
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
crypto ikev1 policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
I still want to assign the IP addresses to VPN clients out of 192.168.3.0/24.
The tricky part is understanding exactly what NAT rules to insert and to avoid that error message I'm getting relatred to the encapsulated packets. I tried to introduce the commands you had, but it's missing stuff that I would need for L2TP/IPSec (e.g., "mode transport"). I also don't think I want "pfs group5". The above config "works" in that I get connected -- all negotiation is done. It's just that packets from the VPN client are not able to go out to the Internet and I'm seeing that encapsulation error messages when I try to send a packet.
Paul -
My mac Doesn't seem to see my external hard drive (seagate 1tb) I have it usb'd in to the back of my computer, but when I open time machine...it does not see it. Help...please
Yes...at least I thought it was....I have 10.6.8.
That's the whole issue. I want to run/install photoshop elements but I have to have 10.8. for that. So...be fore I install an upgrade (Yosemite is getting BAD press) I thought I'd check my back up...it's not there...I have the seagate plugged in and the usb into the back of the mac...when I try to turn the time machine "ON" it says airport device not found not ....
By the way...I REALLY appreciate the help here....
Maybe you are looking for
-
Time Machine, Hard Drive, AirPort Extreme, and possible damage?
I plugged in an external HD to my AirPort Extreme (gigabit) base station today and started a Time Machine backup to it. After about 8 hours, I had transferred only 12 gigs of my 46 and ended up stopping it. I realize only the initial backup should ta
-
Service Enhancements ESR - Integration Builder
Hello, I made some enhancements of standard services in the ESR. In the ABAP backend I created the corresponding proxys. But when I try to to configure the enhanced services in the Integration Builder I only get the standard services. How can I refer
-
Require information about archiving
Hi All, We are executing the report FAGLL03 (G/L account line item Display G/L view) for a few GL accounts. We are able to get data from the report at the beginning months of the year but towards the end of the year due to high volume of data in FAGL
-
Flash debugger needs an expression-watch window
Hi. I would like to propose in next update of (CS4 or CS5 - if it hasn't yet implemented) to add an expression-watch window. I want to use Debugger to find a bug, inside a movieclip, that has dynamic created other movieclips and I want to check some
-
Displaying data in REUSE_ALV_GRID_DISPLAY dynamically
Hi everyone, I've been trying to figure out on how I can do this. I hope you could help me with my dilemma. I'm trying to display my itab. Here's the output I wanted. EX: myitab lastname, firstname, mi, loan name, loan