Wrt54g - no wired connection - cannot find ethernet port upon setup, cannot get wired connection

I've had my wrt54g router for a little over 1 year. I had to get support to set up the router initially b/c it could not find the ethernet port when I tried to set it up initially. I am past that date and recently had to move the router and the PC. When I tried to redo the setup same issue - i upgraded the firmware and same issue. If i uplug the router and plug the cable directly from the cable modem into my pc, everything works well, but when i try to set up a wireless connection, the wired connection goes down, but the wireless connection works and i cannot get the wired connection back up. i am a novice with the device, so any detailed help in trouble shooting the problem and getting me back up on both a wired and wireless basis would be appreciated.

As you upgraded the router's firmware,I would suggest you to reset the router for 30 seconds and configure the router from the scratch.Make sure that the Modem is connected to the router on the internet port and the computer to the router on the ethernet port.
Also check the ip address you are getting on the computer hardwired to the router...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,try to open the setup page..

Similar Messages

HT6437 My itunes cannot locate my ipod. All the sync option are grayed out and diagnostics says that itunes cannot find usb ports and that no device is connected when it is. What should I do to solve this issue?

So itunes is giving me problems. Since around Christmas time, itunes decided to stop reading my ipod. I connect it to my computer with the usb cable and my computer will recognize that a device is connected but itunes will not. If I go to file->devices and try to sync, all of my sync options are grayed out, while before it would just automatically sync.
When I run diagnostics it tells me that under ports that it cannot find usb ports (it has a green circle?), a type of cable isn't found, and that no device is connected with the usb cable (which my ipod is). I have been trying to fix this issue but nothing is working. I've tried restarting my ipod, itunes, and my computer, i've also tried resetting my ipod and uninstalling itunes then reinstalling itunes but nothing seems to be working.
Does anyone know how to solve this issue?

Do the USB ports work for other devices?
Does the iPod charge?
See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- Then do the other actions of:
iOS: Device not recognized in iTunes for Windows
paying special attention to item #5
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem

I have a MacBook Pro and all of a sudden I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

I have a MacBook Pro and all of a sudden I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

BXB1905 wrote:
I tried the Apple diagnostics it did not work.
What do you mean it did not work! What were the results of the diagnostic tests?
Have you contacted your ISP to determine if the problem is on their end?
Have you changed your router channel? Sometimes this resolves wireless problems.
Your profile confirms you are using Lion. Check out the following:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
Configuring 802.1X in Mac OS X Lion and Later

Network Configuration Window Freezes When USB NDIS Internet Connection Sharing and Ethernet Port Are Used Simultaneously

Current Setup:
Asrock Extreme 4 Z77 mobo with built-in Broadcom NetLink (TM) Gigabit Ethernet. Windows 8 Pro. Intel i5-3570k (using onboard Intel 4000 HD Graphics). RAID0- 2 OCZ Vertex 4's.
I will refer to this setup as my tower.
The Ethernet port works fine by itself. When I use wired tethering with my Android phone (Droid 4 running on 4.0.4 Ice Cream Sandwich), it works fine when nothing is connected into the Ethernet port in the mobo.
The issue arises when I try to connect both simultaneously. The network configuration window in windows basically freezes and I cannot really navigate it without a ~60 second delay at best.
I would like to be able to accept the internet from my Android via a USB tether and either bridge the connection or use the internet connection sharing service to route traffic through the unused Ethernet port on the mobo (either to another computer/xbox
or more desirably a switch/router to spread to the entire home network). I have extensively researched the issue of Windows 8 become slow and unresponsive when I attempt to do this and I have not found anyone with the exact problem. I am able to
do both the MAC bridge miniport (bridge 2 connections) and Internet Connection Sharing though a Windows Vista (home premium) Laptop I have. The difference between the laptop and the tower I am try to do this on is the laptop has a WIFI and Ethernet connection
while the tower only has the on-board Ethernet.
Do I have all the necessary equipment to accomplish this, or do I need to buy a PCIe WIFI card? If so could I get away with just getting a USB WIFI dongle?
Any help would be very appreciated.

I had the same problem and came here by searching.
Per Rosengren's method solved the problem, but he didn't say how to do it, so I'll try to explain step-by-step for anyone that may venture here.
Open Device Manager (right click on Computer > Manage > on the left side, under System Tools choose Device Manager)
Choose the problematic device in Network Adapters (for me it's called HTC Remote NDIS based device)
Right click on it and choose Update Driver Software...
Click Browse my computer for driver software
Click Let me pick from a list of device drivers
Uncheck the box Show compatible hardware
For the manufacturer, choose Microsoft Corporation
Now you will have two options:
- Remote NDIS based Internet Sharing Device
- Remote NDIS Compatible Device
I chose the second one and it solved the problem, but if it doesn't work you could try the other one. In my case, the driver that was being used was neither of these, but a special driver from Android SDK ADT bundle.
Pick one and click Next. If a dialog comes up, confirm by clicking Yes.
Wait a few seconds for the connection to restart. If it doesn't work, try disabling and reenabling USB tethering on the phone, or reconnect the USB cable.
I should also note that I'm using a custom Android ROM on HTC Wildfire S (unofficial Cyanogenmod). If you have a stock ROM with HTC Sense, maybe this method may not work and you'll need a proprietary HTC driver.

Accessing Macs connected to the ethernet ports on an Airport

I can't access with Apple Remote Desktop or screen share to a computer (Mac Mini 10.4.11) connected to the ethernet port on my Airport (Time Capsule).
The device gets an ip address in the same subnet as everyone else on the network (everyone else is wireless). Apple Remote Desktop is check off in the Sharing system preference (with access privileges for the admin account). I can ping the IP address of that computer from other computers on the network. Not sure what I'm missing.
The goal is to use the Mac as an iTunes server for the the AppleTV.
Any ideas of what I'm missing. Thanks
Karl

This is possible, but not with Bonjour or any other fixes. It is just a printer set up based on the Port name of the Airport, 10.0.1.1.
I found the answer on YouTube, Title: Windows Printing For Apple AirPort Extreme without Bonjour Wireless wifi.

I have an Airport Extreme which I'm using for a wireless network. Can I also plug in my iMac to one of the free ethernet ports on the Airport Extreme to connect to the Internet that way? Thank you.

I have an Airport Extreme which I'm using for a wireless network. (The wireless router is connected to a DSL modem.) Can I also plug in my iMac to one of the free ethernet ports on the Airport Extreme to connect to the Internet that way? Thank you.

Yes, you can.

I accidentally deleted an Application on my iphone 5 and with it lost important files. How do i get back these files. The last iphone backup sync was after this so I cant even access an older back up as I cannot find them. How do I get back my Lost files.

I accidentally deleted an Application on my iphone 5 and with it lost important files. How do i get back these files. The last iphone backup sync was after this so I cant even access an older back up as I cannot find them. How do I get back my Lost files.

On your iMac launch iTunes and at the top next to the Apple symbol click iTunes > Preferences > Devices and tell me what you see. You last sync should be there showing only a device name. If you have an older backup it will be there as well the difference is it will be the device name with a date and time stamp. Sync and backups are two different things and there is a chance iTunes made a backup the first time you hooked up your iPhone 5.

I downloaded Zapya Apk in my IPad. And I transfer songs from my Android phone to my IPad. After that I opened Dj mixer 3 App and find the songs to make remix but I cannot find any songs. I cannot find in my iTunes also. So what should I do?

I downloaded Zapya Apk in my IPad. And I transfer songs from my Android phone to my IPad. After that I opened Dj mixer 3 App and find the songs to make remix but I cannot find any songs. I cannot find in my iTunes also. So what should I do?

Zapya.apk is an android app and will not work on an iOS device.
How did you transfer your songs from your Android phone to your iPad?

I have seen a wobble bass for dubstep and cannot find it. How do I get it?

I have seen a wobble bass for dubstep and cannot find it. How do I get it? For garageband.

Non-Profit http://www.adobe.com/volume-licensing/non-profit.html

HT3204 My iTunes cannot find my wireless network and I get erros saying I am not connected to a network. What is the best way to resove this issue?

Getting error message: iTunes couldnot connect to the iTunes Store. An unknown error occurred (0x80092013) Make sure your network connection is active and try again. Obviously my network is active, or I would not be able use my internet connection to enter this community. I have a Telus TwoWire Wireless modem. I used the iTunes for Windows: Network Connectivity Tests and found that it was finding my adaptors, but could not connect to my Wireless network. can someone provide a method for iTunes to recognize my wireless network. I can find lots of info on connecting to a WiFi iDevice, but nothing so far about setting up iTunes with my wireless info. iTunes does not have seek network function in the settings, or at least I cannot find one.
Thank you.

Hi MeMiri,
Welcome to the Support Communities!
The article below will walk you through the troubleshooting steps for connectivity issues with iTunes:
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
I hope this information helps ....
Happy Holidays!
- Judy

Trying to confiq cisco bridge WET200. connected to macbook ethernet port. entered 192.168.1.226 for config util. Times out.

I am trying to configure (due to WEP code on my wireless network) Cisco bridge WET200 for use in my home theater. To configure, I connected to ethernet port of macbook OS 10.6.8. Entered IP address 192.168.1.226 for config utility but it times out. Cisco says I need either IE or firefox. Downloaded firefox but still fails. Has anyone had experience with this?

Found that if I clean up DNS for my domain with PTR and A then everything started working properly after a rebuild.

How to find which port on the switch that it connected with Mac address?

Hi,
I am trying to find which port of the switches it connected to thru mac-address?
I am able to get the mac-address from the ip address when i do
"show ip dhcp binding snooping" at the core switch.
But when I move on to the Edge switch to check which PC with this Mac address connected to the port,i returned with no result.(onli trunk port result)
I use sh ip arp | inc 000d.60cb.445d
but didn't give me which port it connected to.
How to solve this problem?
thanks!
KL

Hi KL,
If you are already on the edge switch you can run a command "sh mac-address-table address " and it will give you the port number.
Incase you get a port which is a trunk port that means the end device does not exist on this switch and exist on some downstream switch. So you can just find out the ip address of the downstream switch with "sh cdp neigh detail" command and connect to that downstream switch and then again issue the command "sh mac-address-table address " and check the port number and follow the above steps till the time you get the switch on whcih end host is connected.
HTH, if yes please rate the post.
Ankur

My computer says it cannot find my camera, how do I get my camera to become connected?

The camera on my macbook pro says it cannot be found. How do I get my camera connected?

- Have you tried a reset to see if that will make iTunesee the iPod?
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Next try recovery mode. For that see:
iPhone and iPod touch: Unable to update or restore
- Then DFU mode:
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If somethng always shows on the screen, let the battery fully drain. After charging for an hour try the above again.

My magic mouse will not attach without commanding it to connect it finds the mouse then it cannot find mouse ever since i installed lion

since loading lion i have had no end of issues
The magic mouse will not auto connect but the track pad and key board will once connected the mouse works fine..
For my birthday i was given a ipad FOR Chrismas i GOT A Diary

Hi,
I am having the same issue listed above on my new Mac Mini i just bought, I also contacted Express VPN support and got the same instructions with exception of the command to run in the utilities terminal. I tried the steps listed, and both commands (posted here, and sent to me directly by Express VPN support), and still unable to connect on my Mac Mini running OS X 10.8.2, but I am able to connect on my iPad and my MacBook which is running Mac OS X 10.6.8. Usually Express VPN is spot on with their customer support, but this is taking longer to get resolved. Here is the steps sent to me
Try doing the following to see if the problem gets resolved:
Please follow the instructions here: https://www.expressvpn.org/support/setting_dns_servers_mac_os
(should still be the same for Lion) and then add the following DNS servers: 8.8.8.8 & 208.67.222.220. After adding the DNS servers, please do the following steps as well:
Note: If you're connecting to your ISP via a PPPoE connection, then set the DNS servers on the PPPoE connection itself and then restart your computer for the DNS settings to take effect.
1. Click on Applications
2. Click on Utilities
3. Click on Terminal
4. Type the following command (without the quotes): "sudo killall -HUP mDNSResponder"
5. Press enter and then try reconnecting to the VPN.
If you're still unable to connect, please send us in the latest log files.
Hope this helps. Let us know how it goes.

I had to reset Firefox and now cannot find the calendar, how do I get it back?

I was removing files associated with web.longfintuna.com from my PC. I then reset Firefox. When I open Firefox, all my email, bookmarks.etc. are there. However I cannot find the calendar. I had it before and now cannot locate it.

When you reset Firefox then a new profile is created and some personal data (bookmarks, history, cookies, passwords, form data) is automatically imported and the current profile folder will be moved to the desktop (Old Firefox Data).
You will lose extensions and other customizations (toolbars, prefs) that you've made.
It is possible to recover more data from the old profile, but be cautious not to copy corrupted files to avoid carrying over the problem.
*https://support.mozilla.org/kb/Recovering+important+data+from+an+old+profile
*http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

Wrt54g - no wired connection - cannot find ethernet port upon setup, cannot get wired connection

Similar Messages

Maybe you are looking for