WRT54G-on't see router in list of access points

Hello everyone, hopefully someone on here can help me out. I recently had to reset my router, and now, when my laptop searches for wireless networks, my router isn't showing up on the list. I can access the routers setup screen, and I remember when I first got this router, the same thing happened and A friend of mine did something to one of the settings in the router so that I can connect to it wirelessly. Any help is appreciated!

try changing the wireless channel

Similar Messages

  • Can't see my wish list n access my Account, anyting to do with some App I installed?

    I have problem with my iTunes Account when I log in my Mac, couldn't see my wish list n access my Account.
    but if I log out n log in as a guest user, my iTunes Account works normally.
    I have a guess it might be the App I had installed.
    anyone can help?

    you might want to check on this possibility:
    No music shows up in iTunes after upgrading

  • How to setup a wrt54g router as a wireless access point to extend wifi signal from e3200

    how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
    everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
    any tips to avoid interfearance once setup?

    You have to connect both with a cable.

  • Converting a BEFW11S4 V.2 router to a wireless access point. Can it be done?

    I recently upgraded my home wireless router to an N device.  Now, I'd like to use my old B wireless router as an access point to improve coverage on my property.  I'd like to place it in a location in my house too distant from the N router to connect it with a cable.  Any way to configure the old B router as a wireless access point?
    Thanks for any help you can give me.
    Dave

    yes..u can certainly configure the router as an AP ... follow the steps below :
    1)connect the B-router's port 1 to once of the LAN ports of the N-router
    2)access the B-router's web ui , using its ip address
    3)configure the wireless settings....in case , you want to make a roaming wireless network , the wireless settings on both the router should be same
    4)if the ip add of the N-router is 192.168.1.1 , then change the ip add of the B-router to 192.168.1.2 and disable its DHCP server ..

  • Wireless sporatically stop. List your access point please.

    After some testing I have come to the conclusion that this problem is access point dependent. Not by brand but by model. So in an effort to try and determine the common denomenator could you please list your access point (Model/Brand), what type of encryption, if your channel is set to auto, what version of Mac OS 10 you are running, and if works or not.
    I will keep a compiled list at: http://bluefixed.com/random/waps.html
    Feel free to email me the information at jcanady --- at --- gmail

    An E3200 in bridge mode...........
    http://homecommunity.cisco.com/t5/Wireless-Routers/2-E3200-with-the-same-SSID/td-p/510158

  • WRVS4400N v1 Router with 3 WRT600N (Access Points) locks Internet access

    Have the following equipment
    1.  WRVS4400N  (DHCP Services and connected to DSL modem on different subnets, QuickVPN enabled but not working)
    2.  3 WRT600N used as Access Points troughout the house  connected to the ports on the above router
    The problem is that after working for a while the internet access locks out....  although the wireless laptops get an IP address and can see other network equipment they can't access the internet.  After a restart on the WRVS4400N everything works again.
    If I connect to one of the ports on the DSL everything is always working.  So what could be causing the problem?  I don't want the client to have to restart the WRVS4400n router every day.
    Any ideas?

    Please update the WRVS4400N v1 to the latest code. The  new code fixes some of the DHCP issues
    http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=Wireless+Router+Firmware&mdfid=282446893&treeName=Routers&mdfLevel=Model&url=null&modelName=Cisco+WRVS4400N+Wireless-N+Gigabit+Security+Router+-+VPN+V1.0+%26+V1.1&isPlatform=N&treeMdfId=268437899&modifmdfid=null&imname=&hybrid=Y&imst=N

  • WRT54GNX2 Router set up as Access Point

    How can I configure the WRT54GNX2 as an access point and connect it to our network. I can't seem to get the magic settings.

    Uh, ok. I figured it out. I feel stupid now.. LOL! Now to set it up so that it can only route to the Internet port on the Internet router, so that people can use the internet, and not get access to our network...

  • RV325 Router: Adding a wireless access point for wireless printer

    Hi all,
    I am trying to add a Linksys ea6350 wireless router to the RV 325 router with the goal of having a wireless printer on the network. I can connect wirelessly to the router and access the internet; PC's that are on the wireless router can find the printer and print. However, PCs that connected to the RV via LAN cannot. I am assuming that this has to do with how the traffic from the wireless router is handled and that basically at the moment both routers are functioning as two separate networks. 
    Is this something that can be remedied from the Cisco router side? Or the Linksys? Or Both?
    Thank you

    Hi Jow, it sounds like you have this EA router connecting through the WAN port going in to your RV router, that would make the most sense because it would NAT your connection, allowing you to wirelessly connect but your LAN connection to the RV325 not working.
    If you want to fix this, move your connect from the EA router on to a "LAN port", disable the DHCP server then make sure it is on the same IP subnet as the RV325  and just let it broadcast the wireless signal. The EA router LAN ports are normal switch port so it will work ok.

  • Router, access point, very CONFUSED. HELP

    The Plan:
    In my living room I have a modem/router (at&t supplied) which produces wifi for my home. In my family room I have an older version of the Xbox 360 with no wireless capabilities. Without buying a 100 ft (the rooms are not exactly close to each other)ethernet cable and running it under the house, I'd rather find some way to send a wireless signal from a router to a physical (access point/router?) which will be located next to the Xbox that it can hard wire to.
    Equipment at my disposal:
    WRT54G ver.6
    WAP54G ver.2
    Question:
    Is it possible to do what I want with the equipment I have? The more I dive into websites about it the more confused I get. Access points, client bridge mode, client mode, repeater, etc. I just have no idea what to do, any ideas?

    Those devices that you have will work but it is not an assurance that those two devices will give you the best performance since those are only wireless-G devices.  What you can do is to set the WRT54G v6 as the main router that will broadcast a wireless signal to that other room; set the WAP54G v2 as an access point client so that it will act as the wireless adapter for your Xbox. To test if the router’s signal will reach to that room then you need to use a laptop and check if the laptop could pick the signal. 

  • Roaming between RV220W wireless router and WAP121 Access Point

    Hello, I have recently purchased a RV220W wireless router and a WAP121 access point and i would like to allow my users to "roam" between the two networks as needed (so when the user is closer to whichever one they connect to that one since it has a better signal). For the most part I only have experience in cisco IOS and in actual routers not the wireless stuff so my knowledge has not exactly transfered over well.

    William,
    WDS will not work between the RV220W and WAP121 due to incompatible chipsets. The RV220W can be repeated using WDS by another RV220W or RV180W only. You will need to plug the WAP121 into the RV220W or try WorkGroup Bridge mode to repeat the signal.
    Regarding roaming, the router or AP are not aware of each other and do not have the capability to disconnect a client and help them connect to the AP with the stronger signal. The client will switch to the stronger AP only when the original signal is lost.
    The Aironet (enterprise) devices have the ability to utilize a wireless LAN controller which can help keep devices connected to the stronger signal and allow truly seamless roaming between APs.
    - Marty

  • How can I see "access point" for "connection method" to use Bluetooth tethering?

    I have been using WiFi tethering.  However, as everybody knows, the battery of my Nexus 5 goes down so fast.  Now I wish to use Bluetooth tethering.  I updated my Nexus 5 to Android 5.0.  I have a desktop PC, notebook PC and new Surface
    Pro 3 all with Windows 8.1 Update.  Up to pairing everything goes OK but when I click the "Nexus 5" graphic on the control panel, I could see only "direct connection" (no "access point").  Some website indicates "KB290440"
    but it is not found in the history of update.   I would therefore appreciate if somebody would kindly help me to use Bluetooth tethering.
    By the way, the Windows system I am using is Japanese.
    Thank you in advance.
     

    Some website indicates "KB290440" but it is not found in the history of update.  
    That's the latest "servicing stack".  I think it is optional.  More significant I think would be whether you have the latest rollup, which is also optional, so far.  E.g. at the top of View your update history see what you have for 
    "Most recent cumulative update: "
    FWIW here is mine:
    http://support2.microsoft.com/?kbid=3000850
    HTH
    Robert Aldwinckle

  • Linksys Wireless-B Router & Access Point question

    Ok, I have a Linksys wireless B router (cant remember the model name off of the top of my head) and it connected to a desktop that I have.  I just purchased a Buffalo Wireless-G MIMO router which has the ability to act as an access point.  I was wondering if I set the Wireless-B router up to my desktop where my modem is, and then turn on the Access Point feature with my Buffalo router, would the two brands work together or no?  Also, if they did work and the Buffalo router acted as an access point would I be able to connect my PS3 via one of the ethernet port on the back of the Buffalo access point?  Help would be greatly appreciated, thanks.
    I just purchased this Buffalo router after returning the Linksys Wireless-G with SpeedBooster and having numerous problems with my Verizon DSL (Westell 6100 modem).

    Yes you can.  Here is a LINK to use as a reference.  The only thing you will run into is the routers IP's may be different so make sure they are in the same range.  Example router 1:192.168.1.1  and router 2:192.168.1.2 but it may vary depending on what you want your private IP range to be. 
    The router you want to set as a AP make sure it has the latest firmware and has the SSID/security all set up.  Make sure the IP for the router is set then disable the DHCP.  Then connect router 1 via numbered port to the number 1 port of the second router.
    Message Edited by Ikester on 07-16-2007 09:43 AM
    Richard Aichner (Ikester)

  • I have an iTunes account where I have downloaded Digital movies & I am able to see the list on the desktop of the original downloads. When I log on another device with my login I do not see my list to access them. Why can't I access from another device

    I have an iTunes account where I have downloaded Digital movies & I am able to see the list on the desktop of the original downloads. When I log on another device with my login I do not see my list to access them. Why can't I access from another device

    Hey GingCarv,
    Great question. You'll want to download the movies from your purchase history. The following article explains how to do so:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store
    http://support.apple.com/kb/HT2519
    Note: At this time, movies are not available for automatic downloads.
    Thanks,
    Matt M.

  • HT1222 How in the **** am I to get to the next email that I don't want to delete or put somewhere I can't see my email list on the left hand side??

    HHow in the **** am I supposed to read my next email when I don't want to put my previous one. Somewhere and why can't I see on the left hand side all my emails for viewing I don't want to receive some and delete ASAP but all I getting is a full view of the next one

    If you're talking about the built-in Mail on the ipad - you will always see the mailbox list in landscape view (ie turn your ipad sideways). In portrait view, you should be able to see the Inbox link at the top left of the screen if it's hidden.
    Matt

  • Where can I see the downloads LIST when downloading podcasts, like in the older version of iTunes?  I find it frustrating that I see only one at a time now !  Any suggestions please?

    Where can I see the downloads LIST when downloading podcasts,
    like in the older version of iTunes?  I find it frustrating that I see only one
    download at a time now !  Any suggestions please?

    Thanks for taking a stab at it: that didn't prove to be the problem. That option in the settings for tabbed browsing was not checked.
    I may be a bit behind the times: I am used to tabbed browsing showing all the tabs it possibly can, instead of just the last one. Sometimes it won't even show the last tab: I can have 15 tabs open, and not see a single tab. I've been confused by this into closing a window with lots of tabs open, because it looks like a single page-window.
    My main problem with the tab-bar flashing to the end of the row is that it means a great deal more mouse-clicking around to browse.
    I haven't tried installing the latest beta. Maybe that would fix the problem.
    Toddo

Maybe you are looking for