WRT54G: plugged in and connected to internet, tried to go thru setup and now I can't

Hi folks. I just got 2 computers and I am trying to get my laptop so I can use it around the house. I got the modem and I plugged it in and fired it up. Everything worked fine without needing to go thru the setup and I was able to use the internet on both my desktop and laptop. I saw that the network I was connecting to was insecure, no password or anything, so I tried to go thru with the setup. I installed the driver and went into the setup, the program was detecting my router and modem and network, it was after it asked me for a password that it started to look for my internet connection again and this time, it just stopped working. The prompt asked me what connection it was (cable) but it still didn't work after. I went back to my computers and neither can use the internet anymore. I resetted the modem and router, and I tried doing it again, the internet works fine, went thru with it and the same situation happens again. What is going on?

Try configuring security manully if the internet is working through the router. try these steps: Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When it prompts for the username and password, leave the username field empty and provide password as "admin" (Without quotes)  click on ok. Click on the Wireless tab- Here Wireless Network mode should be mixed - Provide any name in the Wireless Network Name (SSID) box, all in lower cases without any spaces in between.- Set wireless channel to 11 - And wireless SSID broadcast should be Enabled and then click on save settings.Please make a note of Wireless Network Name (SSID) as this is the `Network Identifier. For Wireless Security : - Now Click on the Sub tab under Wireless > Wireless Security.Change the Wireless security mode to WEP Encryption should be 64 bits.Leave the Pass phrase blank, don't type in anything. And under WEP Key 1 type in any 10 numbers please.Click on save
settings.Please make a note of WEP Key 1 as this is the Security Key for the
Wireless Network.

Similar Messages

  • I stopped the plug-in and now I can't do anything on Firefox?

    I was on youtube and got a pop up saying that my plug-in stopped and I could continue or stop the plug-in. I clicked "stop plug-in" and now when I open Firefox, it does not let me type anything into the web browser or click on anything. Nothing is opening. How do I fix this? What happened?

    Hello
    Change a Firefox setting to turn these plugins back on
    # In the Location bar, type''' about:config''' and press Enter.
    * The about:config "This might void your warranty!" warning page may appear. Click'' I'll be careful, I promise!'' to continue to the about:config page.
    # Search for''' plugins.load_appdir_plugins'''
    # Double-click plugins.load_appdir_plugins to change its value to true.
    # At the top of the Firefox window, click on the File menu and select Quit . When you restart Firefox the plugins will be enabled.
    Please Reply Back to us and let us know if it worked for you or not.
    Thank You.

  • Secure link to itunes store failed computer not connected to internet tried ununininstalling everything to do with itunes no joy also error code coming up E0000225 anybody out there got any ideas

    Secure link to itunes store failed, (computer not connected to internet tried uninstalling everything to do with itunes,no joy also errror code E0000225 appearing. Have turned off windows firewall and also my Bullguarg security settings.Can anybody out there please help me thanks.

    Hi,
    You could be right that the response to clicking on help is a symptom of an entirely separate issue, but nevertheless the secure link to itunes is definitely failed, and I am unable to log into Itunes on either PC.
    I also noticed that even if I click on the link to create a whole new Apple ID, I cannot do that either, presumably because the secure link is not working.
    After I noticed that there were weird things happening this morning, I did change my Apple ID password in the hope that this might resolve it, but it seemed to make it worse.  Now, all of my apple devices keep constantly prompting me for the apple ID password, and randomly either accepting it, or telling me it is wrong.  I know the password is correct because I can log onto the apple Manage My Apple ID screens in a web browser with it.
    I was starting to think that this is an ISP issue (BT Broadband), but I have not seen anyone else posting with the same issue.  Does Apple use a different security protocol to everyone else?  I'm asking because all other secure services seem to be working fine, but anything related to apple that requires a secure connection or authentication is having issues.
    I have also seen reference to making sure that Itunes is listed as an allowed program in Windows Firewall.  I cannot seem to do this because it says that my Windows firewall is being managed by McCafee.  I have checked the settings in McCafee, and it appears to me that Itunes, Bonjour, and many other apple programs have been granted "Full" access.  As said before in any case I have tried temporarily disabling the firewall and even this did not solve the problem.

  • I put the BT WiFi app on my iPad Mini and now I can't connect to the internet.  Please help

    I put the Bt WiFi app on my iPad Mini  and now I can't connect to the internet.  Please Help

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    10 Ways to Boost Your Wireless Signal
    http://www.pcmag.com/article2/0,2817,2372811,00.asp
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
    You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • I updated to ios6 and now I can't connect to internet...need help!

    I updated my ipod touch 4th gen. to ios6 and now I can't get it to connect to the internet.  I'm not sure what to do.  I have typed in the correct server name and password yet it still says "unable to connect."  Does anyone know what I can do?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • I tried partitioning my HD to install linux, the installion was not successful and now I can't boot my mac, I tried internet recovery, it was not helpfull as the disk utility cannot delete the partition I created.

    I tried partitioning my HD to install linux, the installion was not successful and now I can't boot my mac, I tried internet recovery, it was not helpfull as the disk utility cannot delete the partition I created. It was only showing me an error message "EFI files are missing", I realized that it is trying to boot from the new partition I created for the installation of the linux I intended to do.

    It sounds like you may have multiple problems, but none of them are likely to be caused by malware.
    First, the internet-related issues may be related to adware or a network compromise. I tend to lean more towards the latter, based on your description of the problem. See:
    http://www.adwaremedic.com/kb/baddns.php
    http://www.adwaremedic.com/kb/hackedrouter.php
    If investigation shows that this is not a network-specific issue, then it's probably adware. See my Adware Removal Guide for help finding and removing it. Note that you mention AdBlock as if it should have prevented this, but it's important to understand that ad blockers do not protect you against adware in any way. Neither would any kind of anti-virus software, which often doesn't detect adware.
    As for the other issues, it sounds like you've got some serious corruption. I would be inclined to say it sounds like a failing drive, except it sounds like you just got it replaced. How did you get all your files back after the new drive was installed?
    (Fair disclosure: I may receive compensation from links to my sites, TheSafeMac.com and AdwareMedic.com, in the form of buttons allowing for donations. Donations are not required to use my site or software.)

  • I reset my WRT54G and now I can't get online.

    I did a factory reset of my WRT54G v.2 last night after I was unable to access the router's setting to set up a WEP password (couldn't remember login/pass and the default login wasn't working) and now I can not connect to the internet through my router.
    -I have no problem getting online when I run directly through my DSL modem.
    -I called my ISP to see what they recommended- someone told me perhaps a modem reset would help. I'm on a DSL modem, which they had me configure to PPOE. I set up the router for PPOE under the basic settings tab, adding my user name and password. I changed no other settings. Basically my ISP said everything was normal on their end.
    -I've Downloaded the firmware and updated that through the router
    -When the router is fully connected there are no light anomalies that I know of (WLAN light and 1 & 2 ports are solid, internet light blinks once every 5 seconds or so).
    -I've tried powering down, unplugging, and waiting- all the usual tips.
    -My wireless computers acknowledge the router's existence, but like the wired computers, are unable to connect to the internet.
    -On my network's properties the number of packets sent and received climbs at a very small rate, but they do increase (I'm told that activity is a good sign).
    -One of the oddest things is, when I attempt to run the installation software, when connected to the internet directly through my modem, as suggested by the installation wizard, the first step that attempts to check for an internet connection says it can't find a connection even though I can browse the web perfectly fine.
    EDIT: I think this might be caused by my ethernet cable/network running through a secondary port in the back of my PC. The start up disk is looking for a signal from the default/1st port and therefore getting no connection, even though my computer is online. Will have to check this later.
    -When connected to my modem, I run cmd then ipconfig, my IP address is
    192.168.1.13, is there something I need to do with this in the router set up?
    Does anyone have any idea what I could be doing differently? I've reset my router before and never been this stuck. I called customer support but they basically wanted $40 to troubleshoot my router as the warranty has expired and I'd almost rather just buy a new one.
    Message Edited by Writersbloc on 09-24-2008 08:46 PM
    Message Edited by Writersbloc on 09-25-2008 08:22 AM

    "You have to change your router's IP address to be able to access it. It will not give you the internet."
    I'm not sure what that means Richard, but I did change the router's IP address from 192.168.1.1 to 192.168.5.1- isn't that what you meant in your first post. I know that isn't reflected in my screen capture that I took last night, but I did do that this morning after I read your post.
    "Log on to your router and change two settings.
    Change the setting in Setup from PPPoE to Automatic Configuration-DHCP and click on save.
    Click on Advance Routing and change the setting from Gateway to Router then click on save."
    I did this and still same results as far as I can tell. Can't get online through the router.
    "Click on MAC address clone under setup tab ... click enable & click clone ...click save settings ... Check the IPaddress under WAN page ....
    If getting IP in public range .... try going online ...."
    I tried this- at least to the part about checking the IP address under WAN. I assume you mean the WAN page in the modem setup- nothing looked any different after trying what you suggested, and I'm not really sure where I would be "getting IP in public range" or what that means.
    I'm about to give up and just buy a new router to see if I can get the same lack of results with a different one. My ISP maintains that everything is set up correctly on their end and really can't do anything more for me. The Modem works and is set up correctly and they can give tech support for a router.
    Here's what my basic setup looks like now:
    http://i490.photobucket.com/albums/rr270/SukarUDL/BasicSetup.png
    Here's what the advanced tab looks like now:
    http://i490.photobucket.com/albums/rr270/SukarUDL/AdvancedRouting.png
    Modem setup looks the same
    Message Edited by Writersbloc on 09-25-2008 07:05 PM

  • Downloaded file from internet and now I can't find it

    So my dumb ***  downloaded a file from the internet today from an untrusted source and now I can't find it anywhere except for when I click on the downloads button on the safari web browser (i.e. )
    I clicked on the file it shows that I downloaded and this pops up
    "Safari can’t show the file “4-More-PeopleAreUsingCellPhonestoListentoOnlineRadioinTheirCars.xlsx” in the Finder because “4-More-PeopleAreUsingCellPhonestoListentoOnlineRadioinTheirCars.xlsx” has moved since you downloaded it."
    I looked for it in the finder window under the "downloads" folder, looked under "All my files" sorted it by the date added, clicked on the magnifying glass next to the only place I can see it and the file still didnt show up in finder.
    help, anyone?
    I'm running mountain lion on a mac book pro and am but a mere seed in the red wood forest of all the trees supporting this site.
    Random fact of the day: I come to this site often and it has proven itself more than useful but have never posted up a discussion board before so this is my first, hope the screenshots help.
    <Edited By Host>

    Eustace Mendis wrote:
    OK. I downloaded the file. It ended up on the desktop - as it is supposed to since that is my instruction to Safari - and I opened the file with Excel.
    It consists of this priceles gem of information. That's it, nothing else.
    More People Are Using Cellphones to Listen to Online Radio in Their Cars
    Percentage of Cellphone Owners Who Have Listened to Online Audio in a Car by Listening to the Stream from a Cellphone Connected to a Car Stereo
    2010
    6
    2011
    11
    Source: Arbitron, "The Infinite Dial 2011," April 5, 2011.
    Pew Research Center's Project for Excellence in Journalism
    2012 State of the News Media
    I have no idea why it disappeared from your Mac. But I trust this reassures you there does not seem to be anything malicious about the file.
    You might want to search on your Mac using some of the key words in the file.
         Not that I am denying the results but out of curiousity how did you manage to download and locate the file when I didn't provide you with the website from which I downloaded it from?
         The thing is, what I supposedly downloaded wasn't supposed to be an xlsx file nor any type of text file for that matter. I got it from a website called ryushare.com.
    I also tried to search for it with the use of the key words in the file you found and no luck. Any way to know for a fact it's not going to affect my computer? Also, any way I can look for the file and delete it through terminal?
    Thanks again Eustace

  • My Ipod just stopped working, the screen got black and now I can't open it. I have tried to charge it but it doens't work.

    My Ipod touch 5 just stopped working. The screen got black and now I can't use it or start it.
    I have tried to charge it but it doens't start and when I tried to connect it with my computer it didn't work either.
    I saw that you could hold down the "home" button and the "power" button at the same time but my home button doens't work so I can't do that.
    Is there any other way I can fix it or do I have to go to an apple store? 

    Try:
    Turn on without Home/Power Button

  • So my daughter set a password to lock her ipod and now she can't remember it.  I tried to restore to factory settings but it still wants a password.  I tried 0000 and that doesn't work.  Any ideas what to do to?

    So my daughter set a password to lock her ipod touch and now she can't remember it.  I tried to restore to factory settings but it is still asking for a password.  I tried 0000 and that didn't work  Any ideas what to do?

    From this Apple support document: iTunes: Specific update-and-restore error messages and advanced troubleshooting
    This device is not eligible for the requested build: Also sometimes displayed as an "error 3194." If you receive this alert, update to the latest version of iTunes. Third-party security software or router security settings can also cause this issue. To resolve this, follow Troubleshooting security software issues.
    Downgrading to a previous version of iOS is not supported. If you have installed software to perform unauthorized modifications to your iOS device, that software may have redirected connections to the update server (gs.apple.com) within the Hosts file. First you must uninstall the unauthorized modification software from the computer, then edit out the "gs.apple.com" redirect from the hosts file, and then restart the computer for the host file changes to take affect.  For steps to edit the Hosts file and allow iTunes to communicate with the update server, see iTunes: Troubleshooting iTunes Store on your computer, iPhone, iPad, or iPod—follow steps under the headingBlocked by configuration (Mac OS X / Windows) > Rebuild network information > The hosts file may also be blocking the iTunes Store. If you do not uninstall the unauthorized modification software prior to editing the hosts file, that software may automatically modify the hosts file again on restart. Also, using an older or modified .ipsw file can cause this issue. Try moving the current .ipsw file, or try restoring in a new user to ensure that iTunes downloads a new .ipsw.
    Error 3194: Resolve error 3194 by updating to the latest version of iTunes. "This device is not eligible for the requested build" in the updater logs confirms this is the root of the issue. For more Error 3194 steps see: This device is not eligible for the requested build above.
    B-rock

  • I updated Firefox and now Realplayer can't download any videos( download button in upper right corner of video don't pop up and there is no download option if I right click) if I use Internet explorer it works fine, I also went in to make sure I had it ch

    I updated Firefox and now Realplayer can't download any videos( download button in upper right corner of video don't pop up and there is no download option if I right click) if I use Internet explorer it works fine, I also went in to make sure I had it checked to pop up it is?! So it's not just youtube for me its all videos!
    == This happened ==
    Every time Firefox opened
    == the last firefox update
    ''locking due to the age of this thread''

    haven't tried it myself but saw this earlier in a blog somewhere:
    "try retro installing FF v3.6.3",
    makes sense 'cos I've only been experiencing the same problem with mozilla & realplayer combo since updating to latest FF v3.6.4
    noted that under IE realplayer plugin still works fine, button to 'download this video' comes on as before.....
    from what I read retro install will pick up all your bookmarks etc. do no worries there
    naughty, NAUGHTY mozilla people! you were 'bombproof' until today....what happened? good luck sorting it out though!!!! I still luv you!

  • HT1386 I was trying to update my iphone and now I can not activate it, it says no sim card installed

    I was trying to update my iphone and now I can not activate it, it says no sim card installed.
    What can I do now, help please.

    Ntmate68 wrote:
    it's stuck on a screen that has a iTune and plug picture
    See Here  >  http://support.apple.com/kb/HT1808
    Once you have Recovered your Device...
    Re-Sync your Content or Restore from the most recent Backup...
    Restore from Backup
    http://support.apple.com/kb/ht1766

  • I've updated my iphone 3gs from iOS 5 to iOS 6 and now I can't access the internet on 3g, can anybody help??

    I've updated my iphone 3gs from iOS 5 to iOS 6 and now I can't access the internet on 3g, can anybody help??

    I don't follow your instructions... mine goes Settings->General->Cellular and from there it's just on/off options for Cellular Data, Enable 3G, Data Roaming, etc. Or I could go Settings->General->Profile APN Carrier Settings but when I click that it just shows as verified but no Visual Voice APN or MMS Settings. If I click More Details it goes to Signing Certificate which has a bunch of parameters for unlockit.co.nz but I am unable to change anything.
    I just updated my iphone 3GS to IOS 6 and my internet (wifi and 3G), voice and text all work, but the only thing I can't do is send/receive pictures via text message. I am using At&t prepaid sim. I tried turning off the phone completely but I'm trying to avoid a complete restore.. at least until I can understand the problem better! Any help would be appreciated!
    Thank you!

  • I CANNOT ACTIVATE MY ILLUSTRATOR  AFTER FIXING MY COMPUTER. IT SAIS THAT I AM NOT CONNECTED TO INTERNET BUT I AM. IS THERE ANYBODY WHO CAN HELP.

    I CANNOT ACTIVATE MY ILLUSTRATOR  AFTER FIXING MY COMPUTER. IT SAIS THAT I AM NOT CONNECTED TO INTERNET BUT I AM. IS THERE ANYBODY WHO CAN HELP.

    Sign in, activation, or connection errors | CS5.5 and later
    Mylenium

  • I downloaded version 3.6.12 and now Firefox can't connect to websites

    I had version 3.6.9 installed, then I downloaded version 3.6.12 and now Firefox can't connect to websites. It says "Unable to connect." I followed all the instructions on the help page about checking my firewall and removing then re-adding Firefox to the list of safe programs, but it still won't work. Is there any way I can re-download version 3.6.9? Or does anyone know what else I can try?

    I found my problem. I had an expired version of Norton Internet Security that didn't uninstall properly, but I was able to remove it with the Norton Removal Tool and now Firefox works.

Maybe you are looking for

  • How to create a trigger for particular value insertion?

    If I have a Table T, which has columns as A,B,C,D. I want to create a trigger to give an error message if someone inserts or updates T with values in A as '001' AND value in B as '99' Please reply soon.... Thanks

  • Sharing Internet with others via AirPort Extreme

    Hello!! I really hope that someone can help me with this! I have Air Port Extreme in my Mac Pro and I recently set it up so that my girlfriend who has a laptop PC can share my internet connection. My concern is now that anyone in our building can use

  • Pro and air's led display

    Hi, Guys Is there anybody know what is difference between pro's led display and air's? why air's looks brighter than pro's? since apple upgraded pro on Tuesday, is it going to get exactly same display as air's? Thanks

  • Version control and deployment strategies

    Hi, I was looking for input from the community on general strategies for using version control and managing deployments to test/stg/production. Currently, I am using subversion to track my source code, and using the standard flex builder build routin

  • Where can i enrol in the new service to download betas

    as they stated in their presentation that there is a new program for non-developers to download betas, so i just wanted to know is it live yet and is it free?? how can i access it? thank you.