WRT54G Setting static ip and port forwarding for Xbox360

1)This is my first post and I'm a little new at this. I have a WRT54G v5 router with the latest firmware update. I have the proper ports fowarded that I found on this site. I basically want full priority to my xbox360 because I have been having some lag issues and dropping out of rooms, especially when someone is on the computer. I set a static ip on the xbox, I just picked 192.168.1.36 (Is that an ok #?).
2)I have everything hardwired so I disabled 'wireless access web" under administration and I also disabled "wireless network mode" under the "Wireless" section. Is this correct or ok?? I don't want my neighbors or anything wireless accessing my router, will that do the trick?
3)I'm looking at the first page you see at the linksys config page (under setup) and I see a section that says
Static DNS 1:xxx.xxx.xxx.xxx
Static DNS 2:xxx.xxx.xxx.xxx
Static DNS 3:xxx.xxx.xxx.xxx
My question is do I need to put the static ip that I assigned to my xbox in one of these static DNS entry spots??
4)Under: Applications & Gaming>QoS I set Ethernet port 4 (the one my xbox is on) to high priority. Is that all I need to do to get priority to the xbox over the computer? Or do I need to enter something under "Device Priority" such as device name, mac address, etc.? And do I need to enter something under "Application priority" such as: Application Name, Optimize Gaming Applications, Priority, and Speciific port #, etc.??
5) Should I disable UPnP?
It's kind of a lot of questions but I really want to understand this fully, any help is greatly appreciated.Thanks alot!
Message Edited by CJ427 on 01-08-2009 10:34 AM
Message Edited by CJ427 on 01-08-2009 10:37 AM
Message Edited by CJ427 on 01-08-2009 10:38 AM
Message Edited by CJ427 on 01-08-2009 10:40 AM

If your XBOX is Wireless , then you need to login to your Router with the Default IP : 192.168.1.1 by opening up a Web Browser.
Then change the Wireless Settings of your Router SSID , Channel : 11, Security : WEP Or WPA Persoanl.
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
4) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
5) Click on set-up and change the MTU Size to 1452 and click Save Settings...
6) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
7) Also assign the DNS Addresses on the Xbox
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1..
8) Turn off your modem, router, and Xbox...Wait for a minute...
9) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Similar Messages

Problems with Port Forwarding for RDP in WebVPN

Hi,
I'm hoping somebody can help me solve this problem that's been bugging for weeks. We recently implemented a double-layer firewall architecture. Before that, our users can access RDP via port forwarding on WebVPN or the Cisco VPN client without any problems.
After we implemented the double-layer firewall architecture, users who are going through the WebVPN and port forwarding for RDP began to experience frequent disconnections, slowness or freezing connections. The users who are using the client are fine.
I checked the logs and I'm getting repetitive TCP-O for the port forwarding connections for RDP. Additional information: the FW we installed as a 2nd layer is Netscreen. I've already set the policy on it to Any-Any for the meantime to help in troubleshooting but to no avail.
I hope somebody can help me in sorting this out as I'm kind of confused on the difference between the port-forwarding for RDP via the WebVPN and the normal RDP via the client.

Hi,
I didnt see anything marked with red in the above? (Atleast when I was reading)
I have not really had to deal with Routers at all since we all access control and NAT with firewalls.
But to me it seems you have allowed the traffic to the actual IP address of the internal server rather than the public IP NAT IP address which in this case seems to be configured to use your FastEthernet4 interfaces public IP address.
There also seems to be a Static NAT configured for the same internal host so I am wondering why the Static PAT (Port Forward) is used?
- Jouni

I have the new Air Port Extreeme model A1521 and I need to set up port forwarding for HTTP. HTTP is not on the list in the set up. Does anyone know if any of those choices work for HTTP?

I am on a Windows 7 Ultimate PC and right now there is no Airport utility for setting up the new Apple Extreme so you have to do it on your iPad or iPhone. Does anyone know how to set up port forwarding for HTTP to get to DVR security cameras? There is nothing in the list that indicates HTTP port forwarding.

Thanks for your reply Tesserax as I did figure this out on my own. It took a bit because all of the options are not clear what they are for like the previous Airport Extreme and Apple does not support or guarantee that port forwarding will work for you application nor did any of the Apple support persons I spoke too have any knowledge for this feature. You also have to fill in the public if you are viewing through someone else's Wi-Fi or on your cell phone carrier network. This new Airport Extreme is a bit different since you cannot use the Airport utility on a PC like the older model and if anyone else is reading this they should be aware that if you do not have an Apple computer, iPhone or iPad and I'm not sure if some of the other network enabled devices like iPod Touch that you must use that can do it, there is no Airport utility for the PC and you would be wasting your money or have to take it back and get another brand wireless router to use if you do not own any of the above mentioned Apple products.

How do you set up Port Forwarding for ARD 2.2 in AEB N?

Help,
I'm a novice at Apple Remote Desktop (ARD) - not an IT guy, so it has to be pretty basic and detailed.
How do you set up Port Forwarding for ARD 2.2 on the Apple Airport Extreme BS router, 802.11 N. I have one at each end of the internet connection. At one end I have an Airport Extreme N router with 2 macs and eventually 1 windows XP machine (if I can) that I would like to be able to connect to over the interenet (the clients) and at the other end, I have a Mac with ARD 2.2 installed also with an Airport Extreme N router. Note: Both routers use Static IP addresses and all computers use static IP's internally not through DHCP. What are the settings or directions to do this.
I have read and printed out the directions for Configuration of ARD 3.0 that are posted many times in the ARD discusion group, but it uses a Linksys router ( http://www.starkpr.com/ard.htm posted by Dave Sawyer). The Mac router is different, particularly with the place to set a Private IP address. I'm not sure about alot of things, but especially about the Private IP address, what number do I set it to, the one that is in my Network connections list? It automatically changes to a different number in AE N setup for Port Forwarding (by one) as if it is not suppose to the same?????
Are there any directions available that are as straight forward for the Airport Extreme N router, as the one's that are listed here for the Linksys Router's? ( http://www.starkpr.com/ard.htm )
Any and All help will be greatly appreciated.
P.S. I know I should have 3.0 but bought 2.2 just weeks before 3.0 came out and they would not give me an upgrade price, so I'm waiting for 4.0 to upgrade.
Thanks,
Jim

Try the following for each AirPort Extreme ...
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): 3283
o Public TCP Port(s): 3283
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): 3283
o Private TCP Port(s): 3283
o Click "Continue"
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s):
o Public TCP Port(s): 5900
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s):
o Private TCP Port(s): 5900
o Click "Continue"
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s):
o Public TCP Port(s): 5988
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s):
o Private TCP Port(s): 5988
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

Help with port forwarding for the WRT54G

I need assistance please!
I am having issues trying to setup port forwarding for a ftp. I already have set this up for a SQL Server port and it works remotely. When I setup another rule for ftp using port range 20-21 it does not work.
I have confirmed that I have saved my settings, have the correct IP address, etc. I have firmware version 4.21.1 and not sure how to troubleshoot this. Any help would be great.
Thanks,
John

Yes you do need to have the port already forwarded for port 20~21 with both TCP/IP and UDP enabled unless you know for sure your ftp only uses just one of them. That is why I asked what port your SGL was set to. Follow the link that other guy posted and open port 20 and 21 (I only use 21 with no problems) and make sure it is directed to the IP of the ftp host. Also that PC needs to have the FTP enabled in windows. To do that go to your control panel > add/remove software > and on the left side go to add/remove windows components. Then check the box for the ftp and add it. It should ask for your windows CD do have it handy when you add the ftp component to your PC.
Richard Aichner (Ikester)

Port Forwarding For WinXP (RDC) (Using AE 802.11n)

I have some problem and I need some thoughts and input from someone else, Here goes.
Here is what im looking to accomplish. From my work I want to be able to connect into my machine at home (windows XP). I cannot use the standard RDC (Remote Desktop Connection) port 3389. My work blocks all traffic coming through that port. So I need to push it through port 443. My co-worker is doing this just fine with a Netgear switch at home, so I know it should work.
In theory it should work like this.
(In Windows XP I have done this)
Change the registry to move through port 443 (windows web site actually shows you how to do this). I turned off the windows firewall completely. RDC has also been turned on. A static IP has been given to this machine as well
(Airport Extreme I have done this)
Put a static ip and Mac address for the Windows machine. Turned on NAT and Forwarded the UDP and TCP ports for public and Private to port 443. As well as set the private IP adders in the port forwarding to the ip on the windows machine.
(Current results)
I think this is where the beginning of my problem and im not sure if its a windows or a AE problem. Before changing the port on the windows machine I can RDC locally. But cannot get through the AE on the default port 3389.
After changing the port on the windows machine to 443 I can no longer RDC locally and still cannot connect from out side the AE.
Im not sure where to take it from here. Please advise someone im dying to cruse the net from work

Hello Preston Holder. Welcome to the Apple Discussions!
As you are already aware RDC clients listen on port 3389 by default.
To change the listening port will require making a Registry mod. This would be typically used if you needed to access more than one computer remotely. (ref: Microsoft Knowledge Base article 306759)
Locate the appropriate Registry key using Regedit.exe:
HKEYLOCALMACHINE\System\CurrentControlSet\Control\TerminalServer\WinStations\RDP-Tcp\Port Number
From the Edit menu, click Modify and then click Decimal. Choose a new port number. In general, choosing a number between 49152 and 65535 will avoid conflict with any other apps on your system, but you could theoretically use any port on the system. Once you set the port number you also need to configure your router to pass the specified port to your computer.
To access your computer remotely, instead of typing just the IP address, you need to type the IP address followed by the port number like this: 192.168.1.1:50001

Port Forwarding for Minecraft

I have a BTHomeHub 1, and port forwarding minecraft has been an awful experience which I just can't get to work. I've tried everything, and just cannot get this to do what I want.
this is what I have currently set up. Also, how do I tell what my computer is called on my network? I'm not sure if I'm forwarding to the right one.

You need to go to network devices at http://192.168.1.254/cgi/b/devs/cfg/?ce=1&be=1&l0=4&l1=4
Then click Edit which shown on the right of the device interface column.
At the bottom of the page where it says "connection sharing", select the Mcft from the list of applications, then click "apply".
That will assign that application to the device.
You can view all assignments here http://bthomehub.home/cgi/b/games/cfg/?ce=1&be=1&l0=4&l1=5
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Port forwarding for clientless SSL VPN access

Hello,
I am currently trying to set up clientless SSL VPN access for some remote sites that our company does business with. Since their machines are not owned by my company, we don't want to install/support a VPN client. Therefore, SSL is a great option.
However, I'm running into an issue. I'm trying to set up port forwarding for a few remote servers. These remote servers are different and have distinct IP addresses. They are attempting to connect with two different servers here.
But my issue is that both servers are trying to use the same TCP port. The ASDM is not letting me use two different port forwarding rules for the same TCP port. The rules can exist side-by-side, but they cannot be used at the same time.
Why? It's not trying to access the same TCP port on a server when it's already in use. Is there anyway I can get around this?
If this doesn't make sense, please let me know and I'll do my best to explain it better.

Hi Caleb,
if you mean clientless webvpn port-forwarding lists, then you should be able to get your requirments. even the same port of the same server can be mapped to different ports bound to the loopback IP.
CLI:
ciscoasa(config) webvpn
ciscoasa(config-webvpn)# port-forward PF 2323 192.168.1.100 23
ciscoasa(config-webvpn)# port-forward PF 2300 192.168.1.200 23
then you apply the port-forwarder list under a group-policy
Hope this helps
Mashal
Mashal Alshboul

Xbox 360/one problem and port forwarding

For a couple months now (since I got my AirPort Extreme) I have not been able to connect to a certain friend on xbox. I can connect to anybody else however. The only way we can (kind of) connect is if somebody else is host and we both connect to him.
My NAT type is Moderate. When I try to test my connection on my xbox it says that I can connect but I am limited in matchmaking (this is joining games and using voice chat, which is the problem named above for my particular friend). The xbox shows the error and suggests that I enable UPnP or open the port 3074.
The problem is that I have already have! I gave my xbox a static IP and forwarded the port 3074 to that IP.
(I have also tried forwarding all the ports that xbox live uses to the xbox. These being:
Port 88 (UDP)
Port 3074 (UDP and TCP)
Port 53 (UDP and TCP)
Port 80 (TCP)
as found on the xbox website... https://support.xbox.com/en-US/xbox-360/networking/network-ports-used-xbox-live
I made sure to put them in the right text boxes for UDP and TCP so that is not the problem either.)
I know that the AirPort Extreme does not support UPnP but does have a similar thing called NAT Port Mapping Protocol which was already enabled. (I tried all possibilities of enabling/disabling NAT...Protocol and port forwarding/not port forwarding.) --- This is not the solution as I see it
In short: My xbox tells me to open port 3074. I already have. It still tells me to open it and still won't work.
I posted this on the apple discussion page (instead of the xbox discussion page) because I know that it's not an xbox problem. When I had my old linksys router it worked perfectly.

I have this exact same question and problem. I know this doesn't help, but would appreciate any updated information if you find an answer. I'll keep working on this also and let you know if I find an anwer.

Are "Back to my MAC" and "Port Forwarding" mutually exclusive?

I have been using APExtreme and Port Forwarding successfully for several weeks now. The PF is to allow access to game players on a PC which acts as a server on the web. All Good.
One more thing, I have a ISP provided wireless modem/router to talk to the cable and the world. It seems to work either bridged or un-bridged.
I have disabled the wireless on the ISP's modem/router. (Actually the ISP's device doesn't hold a candle to the APE.)
Still all good.
So the firewall is on in the APExtreme and none on the modem router, and I have a port defined for my gamers to get access to my server in the APExtreme.
I now want to implement Back to my MAC on my MBP and my other Apple devices. I believe these use iCloud for which I have an account and it seems to be working well with my iPhone.
In Properties, when I select BtmM, iCloud says communications will be slow if I have port forwarding on. Also I will not be able to use the router function in my Modem/router.
I'd really like to have the modem/router firewall up, and do the port forwarding there, but the BtmM will likely not get through.
So what does anyone suggest?
Can I use BtmM and port forwarding without too much degradation?
Please advise.
Thanks
Barry

To best answer your question on whether the two are "mutually exclusive," let take a look at how Back to My Mac (BTMM) basically works.
BTMM - General Requirements
OS X Leopard 10.7.3+
Active iCloud account. Each Mac & the AirPort router, that will be relying on BTMM, needs to be configured with the same account.
A publicly reachable IP address for your router.
A router that supports either NAT-PMP or UPnP. For AirPorts, be sure it is running 7.6.1+ firmware.
BTMM uses TCP port 5354 and UDP ports 4500 & 5353 for communications.
BTMM - Basic Communication Flow
For a computer connected to the Internet via a router, BTMM "asks" the router for its configuration information. For a router, like your AirPort, that uses NAT-PMP, BTMM will ask the router to assign arbitrary public ports. In turn, the router will provide these port assignments (& the router's Public IP address) back to BTMM.
BTMM then sends this information to the iCloud account. In background iCloud updates a special set of DNS entries to be used by BTMM. These entries are then made available to all BTMM clients using your iCloud account. When a computer, with BTMM enabled, uses your iCloud credentials, it automatically retrieves a list of all other computers/routers that are registered with the same account. All these devices should then appear under the SHARED section of the Finder.
When attempting to connect to a remote computer (or router), BTMM creates a secure connection to that remote device using the information from the iCloud account.
Once the connection is established, the devices can then communicate with each other.
So potentially, unless you are using Port Mapping for any of the ports BTMM uses, they should not conflict.

Homehub 5 port forwarding for Windows Homeserver 2...

Hi
Has anybody any solutions on setting up the HH5 for Windows Homeserver 2011
I've inputted all the rules manually as WHS couldn't complete the task, to find ports 80, 443, 4125 remain closed after manual input.
WHS reply's with UPnP not working / router not working.
BT customer services quite appalling and I'm not paying for Tech Support as the package is only 6 months old and I feel I shouldn't have to pay for a product that isn't working correctly, if it was over 12 months I understand I should pay.
I've manually inputted and setup port forwarding for my Iphone app and Android and they've finally started working.
Cheers
Solved!
Go to Solution.

Can you just put WHS in the DMZ on the HH5?
If you found this post helpful, please click on the star on the left
If not, I'll try again

No devices in DMZ drop down and PORT forward does ...

Hi,
We have just purchased B.T broadband with the new home hub, we have set up our hub/router the same as our old one with the correct ports forwarded for exchange to work and remote web space, it all works internally accessing the address but nothing works externally, emails don't get through etc..
Any ideas?
Also why does my device not appear in the DMZ drop down?
Much appreciated any help, thanks a lot

The home hub firewall will offer no protection to a device in the DMZ, as all incoming ports will be forwarded to the device.
All you will be left with is the normal NAT function, which is needed to provide a range of local IP adresses.
If you look at my security page, you will see there is a website you can use to find open ports.
You may find it better to use a router which supports local loopback.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Port forwarding for playstation 3

Hi there.
Seem to be having some very frustrating problems with our Time capsule.
I'm not much good with it, technically, however I'm trying to open/move/forward/map (I've no idea!)
port: 3074 to enable a specific online game to work on my playstation.
I've not got any connection troubles between the capsule and the console, but from hat I've learnt,
I need to somehow 'forward port 3074'.
I think I know what I'm doing until after confirming everything and clicking 'update' after I've entered the port number, I'm asked to make corrections before the airport can update!
It specifically asks me to enter the 'beginning DHCP address', which i've discovered is 192.163.1.1,
however it then asks for the 'ending DHCP address', which to be honest I have no idea.
I'm really not clued up at all on any of this, I just want to play a game on my PS3!
Any help would be much appreciated.

Hi dlmatthews and welcome to the forum, i've had the same issue, you can't port forward to both, I just DMZ my PS3 and port forwarded to my another PS3 in the household.
If you want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side If the the reply answers your question then please mark as ’Mark as Accepted Solution

Port Forwarding for L2TP/IPSec VPN Behind Verizon Actiontec MI424WR-GEN2 Rev. E v20.21.0.2

I've got a NAS setup with various services running on custom ports to help minimize exposure (especially to script kiddies). I've tested everything both internally and externally to confirm they all work, and even had someone at a remote location confirm accessibility as well. Port forward configurations performed on the Actiontec are working well.
I installed an L2TP/IPSec VPN server, tested internally and it connected successfully. So for all intents & purposes, this validates that the VPN server is correctly configured to accept inbound connections and functioning correctly.
I logged into the Verizon Actiontec MI424WR router, setup port forwarding for UDP ports 500, 1701 & 4500.
Note: I added the AH & ESP protocols based on what I saw on the built-in L2TP/IPSec rules
With the port forwarding in place, I tested VPN externally but it didn't connect.
I've done the following so far to no avail:
Double & triple checked the port forwards, deleted & recreated the rules a few times to be sure
There are no other pre-existing L2RP/IPSec port forward rules or otherwise conflicting port forward rules (e.g.: another rule for ports 500, 1701 or 4500)
There was an L2TP port triggering rule enabled, that I toggled on and off with no change
Verified the firewall on VPN server had an exclusion for L2TP, or that the firewall is off. (Firewall is off to reduce a layer of complexity, but it worked internally to begin with so I doubt that's the issue.)
Since it works internally, and there are no entries in the logs on the device indicating inbound connections, I'm convinced its an issue with the Verizon Actiontec router. But unfortunately, I'm not sure what else to try or where else to look to troubleshoot this. For instance, is there a log on the router that I can view in real time (e.g.: tail) that would show me whether or not the inbound connection attempt is reaching the device, and whether or not the device allowed or blocked it?
My router details:
Verizon Actiontec
MI424WR-GEN2
Revision E
Firmware 20.21.0.2
Verizon Actiontec built-in L2TP/IPSec rule templates. They're not currently in use, but are baked into the firmware for easy configuration/selection from a drop down menu.
Solved!
Go to Solution.

normally a vpn on that router, will have a GRE tunneling protocol as well.
two ways to build the PF rules,
Manually
Preconfigured
I know the preconfigured VPN rules will do the GRE protocol as well, but if you do it by hand you can't get it.

Not enough port fields in port forwarding for Linksys E4200

I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking nerd, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
If anybody could assist with details and options I would greatly appreciate it

Wrong forum, use "small business routers".

WRT54G Setting static ip and port forwarding for Xbox360

Similar Messages

Maybe you are looking for