WRT54g v1.0 problem accesing it via cable connection

Hi i hope someone can help me.
I've got a WRT54g v1.0 and flashed the new firmware.
Via autoupdater and a cable connetion.
After reebooting and reseting i wasn't able to 192.168.1.1 via cable while using the wireless connection the access is possible.
I refashed via cable and the flash worked but still i cant access my
router via cable. Has any one an idear what might be the problem?

Hi...as far as i know there is no known linksys auto updater for wrt54g v1.....so which auto updater you have used?? and what is the current firmware on the router??
the current firmware on the linksys website is "4.30.5"...if you have this firmware..then try resetting the router for 30 seconds and do a power cycle....force the card speed of NIC card of the PC to 10 mbps half mode...disable the firewalls...and check whether you can access the router now....
and also make sure that the wireless network you are connecting to is the wireless signal of your own router....meaning that you aren't connecting to your neighbour's network...

Similar Messages

Low speed via cable connection

So, I have this Airport Extreme 802.11ac wireless router (http://www.apple.com/airport-extreme/) and I can't get the advertised speed. My internet connection speed is 1Gb/s, but I can't get it from this router (via cable or wireless connection). I did >100 speed tests on http://www.speedtest.net/ with the router and the maximum speed was 217Mb/s. The maximum speed when I've connected my iMac directly to my ISP's internet cable was 926Mb/s.
Does anybody have the same problem?
I'd like to note that all cables for the router's clients and WAN are CAT 5e cables.

WAN to LAN throughput when the AirPort Extreme ac is set up in router mode is going to be in the range of 300-350 Mbps on a very good day. You might want review the test results below:
http://www.smallnetbuilder.com/tools/charts/router/bar/74-wan-to-lan
What speed do you see if you leave the AirPort Extreme connected to the Internet and then connect your Mac to one of the LAN ports on the AirPort Extreme?
It won't do much good to test wireless until you can get the WAN to LAN speed over Ethernet up to the 350 Mbps range.

Problems downloading iOS via iTunes - connection timeout

I have a terrible internet connection and am getting poor speeds. Other than the obvious "get a better internet service" is there a way to improve my chances of downloading the nearly 600MB iOS 4.3 package?
I've tried twice now and managed to get over 300MB both times. After the timeout error message I have no choice but start the download from 0. Is there some way to download the update in smaller packages? Is there a download manager that supports iTunes restating from partial success (I know, probably a dumb question but I have to ask .. just in case)? Other suggestions?
Thanks a lot folks.

Same here. Network timed out... on 25MBPS download... curious. This is the exact same thing that happened with 4.2.1 came out. I can never download the newest iOS from Apple. This always gives me errors every time I try to update. If it is doing the same thing that it did last time, then I will probably have to take all my devices in to the Apple store, have them do it for me, just like last time. It really is such a huge hassle. Just thinking of not updating at all. All my devices are working just fine without the "updates." I give up. Just tried a second time. I am done trying. Just staying with the iOS I already have.

EzVPN issues with a Comcast cable connection

I have a problem with a Comcast cable connection and an EzVPN. Simply put the connection drops within minutes of no activity. In other words, if I leave an RDP connection open from my datacenter to the remote site, the VPN connection will stay open all the time. A few minutes after I close the connection the VPN drops and the remote side has to wait until its keys timeout to reconnect (obviously without a reset).
I have multiple sites connecting to the EzVPN server without issues from multiple carriers. This one Comcast connection seems to be an issue. I've verified that the configurations for other DHCP based cable connections and this one are the same (except for local parameters). I've also run PING tests to test reliability and MTU issues. For the reliability I do have 1 - 2 packets out of 200 consistently dropping with a 2 second timeout value for the PING. (This is pinging the next hop router on the connection.) For MTU I was able to PING with packet sizes all the way up to 1500 bytes with the DF bit set.
So, I'm looking for any direction on this issue.
Here is the configuration of the router at the remote site (truncated for clarity):
crypto ipsec df-bit clear
crypto ipsec client ezvpn comcast-remote1
connect auto
group comcast-remote1 key testing1234
mode network-extension
peer 65.x.x.x
xauth userid mode interactive
bridge irb
interface FastEthernet0
description Trunk to LAN network
switchport mode trunk
interface FastEthernet4
description WAN connection
ip address dhcp client-id FastEthernet4
no ip redirects
no ip unreachables
no ip proxy-arp
duplex auto
speed auto
crypto ipsec client ezvpn comcast-remote1
interface Dot11Radio0
no ip address
bridge-group 1
interface Vlan1
description primary LAN connection
no ip address
ip tcp adjust-mss 1452
bridge-group 1
interface BVI1
description Bridged connection for Dot11Radio0 and Vlan1
ip address 10.x.x.x 255.255.255.0
ip helper-address 192.x.x.x
no ip redirects
no ip unreachables
no ip proxy-arp
ip virtual-reassembly
crypto ipsec client ezvpn comcast-remote1 inside
bridge 1 protocol ieee
bridge 1 route ip
This remote router is a Cisco 871W running this image c870-advsecurityk9-mz.124-4.T7.bin. I've checked the other 871W routers that are on a DHCP cable connection and they are also running this image version.
Here is the relevant sections of the hub (EzVPN server) router:
crypto isakmp policy 20
encr aes 256
group 2
crypto isakmp policy 30
encr aes 256
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 90
encr aes 256
group 2
lifetime 28800
crypto isakmp keepalive 60 10
crypto isakmp nat keepalive 60
crypto isakmp client configuration group comcast-remote1
key testing1234
acl comcast-remote1_networks
save-password
crypto isakmp profile comcast-remote1_isakmpprof_dyncorp
match identity group comcast-remote1
isakmp authorization list comcast-remote1
client configuration address respond
accounting svpn_accounting
keepalive 60 retry 10
crypto ipsec transform-set high_security esp-aes esp-sha-hmac
crypto ipsec df-bit clear
crypto dynamic-map comcast-remote1_dynmap 20
set transform-set high_security
set isakmp-profile comcast-remote1_isakmpprof_dyncorp
reverse-route
crypto map svpn-map 109 ipsec-isakmp dynamic comcast-remote1_dynmap
interface FastEthernet0/0
bandwidth 102400
no ip address
speed 100
full-duplex
no cdp enable
interface FastEthernet0/0.40
encapsulation dot1Q 40
ip address 65.x.x.x 255.255.255.0
no cdp enable
crypto map svpn-map
crypto ipsec fragmentation before-encryption
interface FastEthernet1/0
switchport access vlan 4
bandwidth 102400
duplex full
speed 100
no cdp enable
interface Vlan4
ip address 192.x.x.x 255.255.255.0
ip virtual-reassembly
Thanks,
Mike

in your client class - method go()
you have try catch like this: make changes at 2 places commented below
try {
Socket s = new Socket("localhost", 7000);
// ObjectInputStream fromServer = new ObjectInputStream(s.getInputStream());
fromServer = new ObjectInputStream(s.getInputStream());
// ObjectOutputStream toServer = new ObjectOutputStream(s.getOutputStream());
toServer = new ObjectOutputStream(s.getOutputStream());
threadNum = (Integer) fromServer.readObject();
int i = 0;
System.out.println("Thread number: " + threadNum);
System.out.println("Connected to server");
do {
} while (!disconnect);
fromServer.close();
toServer.close();
System.out.println("Connection is closed");
} catch (Exception err) {
System.out.println(err.getMessage());
}

WRT54GS wireless Can't Through Motorolla SB5101 Cable Modem

I have a linksys wrt54gs wireless router. I have had it for almost 2 years, it has been hooked up to a DSL modem, no problems whatsoever. I just moved, and now have a Motorolla SB5101 cable modem.
I followed all of the steps exactly for setting up the router with a cable modem. Everything went smooth, when I check the status of the router, it has an IP address, everything's good. But I can't get online. The modem is fine, I'm hooked up right now via USB. The router is also fine, I can log into it and everything. All the lights are good on both the router and the modem. I downloaded and installed the latest firmware, I've power cycled, nothing. I know it has to be something simple, some setting somewhere.
Please help.

My troubles started after I upgraded my WRT54G V2.0 to the latest firmware. The download firmware file is prefixed with WRT54GV4.0_ which leads me to question if it is supported to run on my WRT54G V2.0 machine.
The full name of the firmware binary in the Zip archive is "WRT54GV4.0_4.21.1.US_code.bin". Please confirm or correct that this is the latest & greatest firmware version for my V2.0 WRT54G.
The problem presents itself as an in-ability to connect to ot ping any IP device past the RF side of the Motorola SBV5120 Cable Modem (also an older Motorola SB4100).
I use DHCP on the Modem with OOL's (Optimum On-Line) DHCP Server, in turn I use DHCP on the Router with the Modem as DHCP server and finally use the Router as DHCP Server for my home network desk top/laptop/printservers/USB wireless hubs. Either the Router's MAC address or my laptop's MAC Address is reported in the SBV5120's configuration as CPE device, depending on which is connected. I can always connect to the internet by cabling my laptop directly to the bodem's Ethernet port instead of the Router's WAN-Internet-Link port.
According to OOL tech Support, The SBV5120 and downstream devices do not care about which MAC addresses is used, just that one is present. Apparently the ability of spoofing to defeate MAC Address Filtering worked, so they don't do it any more (My guess - let me know if I'm right or wrong)
The modem log consistently reports success in completing the DHCP process and reports itself as operational. After a series of power cycle of both modem and router, I was finally able to connect to the internet through the router. This lasted about 28 hours. If I connect the IP LAN port of my laptop, I can connect to the internet.
At this point, I found the firmware alternative, dd-WRT, and replaced the LinkSys firmware with the dd-WRT firmware. Consistent ability to connect to the inter has been the result. The Latest LinkSys firmware is in question. I hope they have a plan to fix it. If not, I'm going to look very closely at the alternatives when it comes time to purchase 11n products.

My Canon MX 922 does not scan. My printer is connected via cable. Wireless doesn't work either.

My Canon MX 922 does not scan. My printer is connected via cable. Wireless doesn't work either. I get an error message with multiple suggestions but none of them apply to my situation.
I am so dissatisfied with this printer. I'm sorry I got it from Amazon because now it is a hassle to return it. I will never buy another Canon.
The printer menus are confusing. I hate using it. I loved my previous Canon which finally stopped working after many years, that's why I purchased a newer Canon model. Never again. Stick with cameras.
Marcy Hotz

This note won't be as angry and frustrated as the last one...
Because I still had my old printer drivers and other applications on my hard drive, I think the application was trying to connect with the old printer. I deleted all the old stuff.
I also had several scanning applications on my drive which just confused me.
When I used the actual Canon MX922 application, I was able to scan but could only save as JPG, TIF or BMP (and one more, I forget which). So I did some research on the Canon site and found out how to save documents as PDF files using the Canon IJ Scan Utility.
It works now. So I'm satisfied, will keep this maching. I just had to take some time, sit down and focus on the problem.

Connecting a second computer to BThub 4 via cable

I do not think this is a BT problem but if any one has any advice it will be appreciated.
For a long time I have had 2 computers and a laptop connected through a BT hub 3. One computer (Vista) was connected by ethernet cable with the other two computers (windows XP) connected by wireless. Everything worked well.
Because hub 3 died I now have a Hub 4. However, I need to change the way my computers connect to the Hub. This means that there will be two computers connected by ethernet cable. The original computer connecterd by ethernet cable is set up just as it was prveiously and works well.
I connected the second computer with the ethernet cable supplied by BTand anticipated it would work. Unfortunately, for some reason I can't get the connection to work despite going through the wizard process of connecting from the computer both directly and via the small home network that is already establised.
One irritating thing is that, although I select a "direct cable connection" in the set up process, when trying to connect I get a screen stating dial-up failed and a retry is instigated. I am not using a modem!
I have tried re configuring things but to no avail, so getting to the end of my ideas, i wonder if anyone on the forum could give me some guidance.
Regards
David

Hi
Thanks to you guys for your help. the main problem was the absence of a net work card. This is now in place and I can make a connection tp the internet via the BT Hub. However, there is still one problem and this is as follows.
Computer A (windows XP) and computer B (Windows Vista) are connected to a small BT hub home network via ethernet cables.
On computer B (which has been successfully connected to the hub for about 2 years) clicking on network places > " view workgroup computers" shows a map which includes the BThub, it's self (B) and computer A.
If I do the same on computer A, it shows it's self but not the othe computer or the hub. Despite this it works perfectly well accessing the internet.
Because I need to transfer files via this network I need to see the othe computer(S) and open files on them, however, I have spent some time trying to establish the presence of other devices on computer A without success.
I have checked folder permissions are granted and I have tried to view the other devices with the firewall switched off but so far no success.
Suggestions gratefully received.
Regards,
David

Is it possible to recover my data from iCloud backup without working wifi? I have as many other upgraded my iPhone 4S to iOS 7.0.2 with the result that the Wi-Fi or Bluetooth no longer works. However, i can connect to iTunes via cable but there is wrong v

Is it possible to recover my data from iCloud backup without working wifi? I have as many other upgraded my iPhone 4S to iOS 7.0.2 with the result that the Wi-Fi or Bluetooth no longer works. However, i can connect to iTunes via cable but there is wrong version of backup.

Answer is no.
If you want the iCloud backup you have to have n internet connection, thus WiFi.
The not working WiFi has happened with quite a number of users.
It is not exactly clear what is the cause but there are suggestions to clear it up:
Some people have had success by removing an apostrophe from the iPhone name. If your iPhone is called something like “John’s iPhone” then this might work. Go to Settings > General > About > Name and change it to something with no apostrophe.
Some people have reported success by putting the iPhone into Airplane mode and then going to Settings > General > Reset > Reset Network Settings, but the problem may return.
You could also try going to Settings > Control Center and disable Access on Lock Screen then turn your iPhone off and on again.
Make sure that your router firmware is up to date.
Try backing up your iPhone and then restoring it. Check how to factory reset an iPhone for details.
If nothing is working for you, try contacting Apple or take your iPhone into an Apple Store.
Succes, Lex

Problem with connetction to wrt54g2 via wireless connection with WPA/WPA2 & wireless MAC filter

Hello,
I'm Alexey from Novosibirsk, Russia.
I have a problem with connection to wrt54g2 from my DELL D630 notebook via wireless connection. When I setup WPA/WPA2 in wireless security and wireless MAC filter I can't connect from notebook to WRT - in Windows I see that dynamic IP address from WRT is not assigned. When I switch off security mode to disable always OK, but I need a wireless security between DELL and WRT.
Connection via cable Ethernet port is OK.
Can You help me?

Have you tried the different laptop...?
Download 1.71 MB the firmware for WRT54G2 v1 and reflash the router's firmware.After reflashing/upgrading the router's firmware,reset the router for 30 seconds and reconfigure the router from scratch.

Mac Mini won't print via ethernet cable connected to airport extreme

Hi. Thanks for your input in advance. Am about to start throwing things around. I have an Airport Extreme based network which is working fine. The printer is a new HP L7590 which connects to the network with a USB cable connection to the Airport Extreme. Those with laptops and wireless cards are able to print no problem. However my Mac Mini, a 1.25 GHz PowerPC G4 is connected to the printer using a ethernet cable connected to the Airport Extreme. All was working perfectly until I upgraded from Panther to Tiger. I am now running 10.4.11. Now the Mini will not print. The jobs keep stopping. I have removed the printer and try to add it again. The print browser page finds the printer okay and lists it as connecting via Bonjour, but when you tell it to add it, it starts 'searching for new drivers' and then 'gathering printer information' and then it stops responding and I have to force quit it. Any suggestions?? I have already tried all the online mac help suggestions.

Actually it transpires that the G4 laptops are not printing either now.

WRT54G v6 Odd Problem

Hiya. I lurked these forums a bit and looked around but I did not really find my problem listed here. I will describe it as best as I could.
I was playing a game online when all of a sudden my Internet connection dropped. I looked at my modem, thinking perhaps my cable connection dropped (it WAS at about 4:00 (4:00 AM), and the cable company sometimes disconnects the service for a bit for maintenance or whatever. Hell if I know.
Anyways, my Internet connection was all lit up so I looked over to my router and the wired port #1 light was blinking. Not normal "activity" blinking, but blinking on and off very slowly, about once per second.
I have two computers hooked up to my router and did a little testing... I plugged in computer #2 into all four ports and the lights were just fine. I plugged Computer #1 into all four ports and there was a problem. When computer #1 was in ports 3 and 4, it worked fine. But when it was in ports 1 or 2, the light blinked in the fashion I just described.
I tried reinstalling the router, reinstalling my network card, and upgrading the firmware. Nothing worked. (I called tech support but my P.O.S. cell phone dropped the call. >: )
Nothing worked. I mean, I could get both computers working fine by plugging it in another port, but Hell if I was going to let this problem stick around.
Now I am a computer repair technician. I did every conceivable option aside from reinstalling Windows (it was basically a fresh install, I doubt that was the problem) and nothing worked.
As I was browsing the forums over here I noticed that my model, the WRT54G, has a lot of problems. Bah. Anyway, after about an hour total of the lil' blinky problem, it just stopped on its own.
I was just wondering if anyone knew what this was and if it happened to anyone else. Thanks.

The only thing that I believe that you can do is reinstall the correct firmware in the language that you want. Below is an firmware upgrade link.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=4030&p_created=11601...
Good Luck,
Ttech

WRT54G Wireless Router Problem. Need Help!

I'll start with the basics of my situation and if more details are needed, I will provide to the best of my ability.
I have a comcast cable internet connection. I have 6 computers in my house. Two of them are downstairs (which is where our modem is.) The other four computers are upstairs. All of these computers are Desktop computers with the exception of one laptop.
My laptop (which is Windows XP) can pick up a random wireless signal from the room it is in. I also found out a way to share the internet connection on the computer by going into the properties of my network connection and enabling internet sharing on it. This means if I connect a network cable from my laptop to another computer, I can leech the connection from my laptop and have internet access on the other computer. I also had a switch that I used to connect the other 3 computers upstairs by means of the laptop. The problem was, the laptop was using someone else's wireless connection in the area, and it wasn't strong enough to keep up a constant connection.
I decided, if I can leech someone else's wireless connection, why not have my own. So i recently bought WRT54G Wireless Router and set it up on one of the computers downstairs (because that's where the modem is). It works fine as far as connecting my laptop to the internet from upstairs. My laptop can access the internet through the connection I set up in the LELA program.
Here is the part I am confused about. Everything is plugged in correctly as far as the router is concerned because the laptop can access the internet. But when I connect an ethernet cable directly to one of my other computers (which are Windows Vista, but I didn' t have a problem with it previously when I was leeching someone else's connection), the connection drops on my laptop, and the other computer still can't access the internet. A notice pops up that says its trying to identify the network, but it gives an error that says there is something wrong with the DNS. As soon as I disconnect the ethernet cable connecting my laptop to one of the other computers, the connection is fine again on the laptop. It's only when I connect the computers together that the connection drops.
I just don't understand why it wouldn't work when I created my own network if it worked with another network with no problem. My whole point in getting a wireless router was to have a router within good range to keep up a constant connection on my other computers that aren't in range of the modem downstairs. I just don't know where else to look. I'm not sure if it can be fixed on LELA, manually through my wireless settings, or if it could be a problem with one of my computers' settings. I've tried many different things and I'm not sure what else to do so any help is most definately appreciated. I feel like I've tried everything. I know it's possible because I've one it before, I just need the help because I'm not much of a networking person and I don't know what I should start with to make this work.
Thank you to anyone who can help or even point me in the right direction.

Access router setup page ...Click on the Wireless tab on the Setup page- Here Wireless Network mode should be mixed- Provide any non-linksys name .... Set wireless channel to 11- And wireless SSID broadcast should be Enabled and then click on "Save Settings" >>Now Click on the Sub tab under wireless > "Wireless Security" Change the Wireless security mode to WEP/WPA ...type in the key & click save settings .... >>>>Click on Advanced Wireless settings>>Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" Check the connection once again & see if it works or not ...

WRT54G and Playstation problems

Hello,
I have the WRT54G router v. 4 and I am connected to my playstation 2 through an ethernet cable. I have my PS2 assigned a static IP address and have disabled UPnP (I read somewhere this solves many PS2 connectivity problems).
My wireless connection is nearly flawless and never goes out. However, my wired connection to my PS2 goes out quite often. I also receive "can not connect to ISP" messages sometimes when trying to connect online.
What is the problem and what can I do to establish a more reliable connection?
Thanks.

Try this link to configure the Play Station with the router .....
Hope it works ....

3GS on iOS 6 will not sync most of music via cable

I upgraded my 3GS to iOS 6, and most of my music will not sync via cable. I can check it all in iTunes, but the space allocation bar in iTunes does not change (on iOS5 I only had 1G free, now I have 8 G free), but only about 1/4 shows up on the phone. I did full restore--no change. I checked fill free space with songs--no change. Help! It might be that only music bought from iTunes is syncing and music I ripped myself or bought from Amazon is not syncing--i.e. my enire pre-iphone collection.

Ok solved my own problem--but this is squirrely. In itunes, at the bottom of the "Summary" tab for your phone, is an "Options" section. For some reason, having "Sync only checked songs and videos" checked here only allowed 47 of 1900 songs to sync--even if they were checked on the music tab. Unchecking this box and managing music from the music tab alone fixed the issue.

Проблема подключения через кабель - Trouble connecting via cable

Доброе время суток.
проблема состоит в том, что после переустановки ОС (win7) не могу больше подключить t410 2518 к sony playstation 3 через кабель программой FileZilla Client
до переустановки ОС вводил только 100.100.10.10 и работало, ныне не видит приставку.
В диспетчере устройств и в solution center пишет что нет драйверов для:
- PCI-контроллер Simple Communications
- Основное системное устройство
- Последовательный порт PCI
где их брать и\или что сделать для того, что бы я смог через кабель подключиться к другим устройствам.
Google translation:
"Good time.
the problem is that after reinstalling the OS (win7) can no longer connect to the 2518 t410 sony playstation 3 via cable program FileZilla Client
before reinstalling the operating system introduced only 100.100.10.10 and worked, now does not see the console.
In Device Manager, and solution center says that there are no drivers for:
- PCI-Simple Communications Controller
- Base System Device
- PCI Serial Port
where to take them and \ or what to do so that I could connect via cable to other devices."
Moderator comment: Please do post in your native language, but as the principal language of this community is english, please also provide a translation so that members may assist you. Hopefully, the Google translation provided above is adequately accurate.
Модератор комментарий: Пожалуйста, пост на вашем родном языке, но так как это основной язык этого сообщества является английский, просьба также представить перевод так, чтобы члены могут помочь вам. Будем надеяться, что перевод Google Приведенную выше адекватно точным.
Solved!
Go to Solution.

Thank you, I made it )

WRT54g v1.0 problem accesing it via cable connection

Similar Messages

Maybe you are looking for