WRT54G v6.0 Disconnects From Server After Ten Minutes

I posted this once before and somehow it got....deleted?
Anyway....here we go again. I purchased A WRT54G over the holidays. It has worked fine for me with the exception of a real estate data source (server) that I need to use for my business. I can log on and start doing my analysis just fine, but when when the ten minute mark hit....the router disconnects me. It's EXACTLY ten minutes...everytime. I've spent the better part of 20 hours on the phone with Liksys Tech Support and they have been very helpfull, but unable to help me fix this issue. They sent me a new router to replace the one I bought thinking that there was something wrong with that router. After installing the router they sent me....same problem. We opened ports, reduced the MTU to 1375, disabled security, ect... with no luck. Can anyone tell me what I need to do? Any thoughts or advice would be greatly appreciated.

Actually try this...
Connect wired to your ISP provider cable/dsl modem and release/renew dhcp lease...
IP address is then assigned based on MAC address of that computer
IPCONFIG to check assigned address
Re-connect wireless router and in settings duplicate the mac address of the PC used above.
Release/renew dhcp on router and check status on router settings pages
assigned IP should be same or in relative range.
Why this may be occuring.... At least what leads to the above suggestion:
ISP providers in the mid-west region around me started assignment of Router based MAC addressing to monitored and limited bandwidth servers - IP assigned would renew into those servers as the MAC address from a router was a clear indication of mutiple PC use and bandwidth consumption.
Duplication of a desktop or wired network card on your PC into the router defused this by detection your MAC appears to be a single PC and the ISP assigns the address to standard server loads.
Try it see if this helps - keep in mind most of these hardware manufacturers use base hardware from common pools of sub-suppliers - I believe you will have just as much issue with a netgear unit.
Daak

Similar Messages

Trying to activate phone on pre-pay and get disconnected from *228 after 1 minute

It says "congratulations your phone is activated" but I need to dial *228 Send to program the phone. I do this and I am disconnected after 1 minute. I have tried this a dozen or so times with the same result. I had my old number transferred and now I can't use that phone either. HELP!

sjt6052
I'm so sorry for the trouble getting your prepaid device to activate! We definitely want to make sure you're connected and running at 100%. While we only have access to Post Paid on this site, I would like to make sure you can get in touch with our PrePaid team. Is there another line you can call from? To reach our Prepay Team from another line, please dial 888-294-6804. When prompted, enter your prepaid phone number. Then press 4 (for questions or to change something), then 5 (for Store Locations or Billing Questions), then 4 (for Customer Service Rep) and then enter your pass code for your account. If you do not know the pass code enter in four zeros. Then the system will transfer you to a Prepaid representative.
RuthW_VZW
Follow us on twitter @VZWSupport

Mac Book Pro with Retina Display 13 disconnect from WIFI after few minutes

Hi. I bought new Mac Book Pro 13' Retina display few weeks ago and noticed that my WIFI connection disconnect after few minutes and connect again after tying with few attempts. It tried with both home and office WIFI to make sure that nothing wrong wireless network or modem itself. It seems it is Mac Pro's problem. How to fix it ?
My Home Wireless Modem *** Router is connected with Apple Time Capsule Machine but in my offce there is no Time Capsule Machine attached. It is so annoying. Need Help.

Hello psadana,
Thank you for the details of the issue you are experiencing with Wi-Fi on your MacBook Pro. I would be concerned about this too.
I recommend reviewing the full article but steps in the section labeled "Symptom: The network connection drops unexpectedly" specifically stand out to me for the issue you described:
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Thank you for posting in the Apple Support Community.
Best,
Sheila M.

5-yr-old Macbook disconnects from wifi after 2 minutes -- why?

Starting about 2 months ago, my 5-year-old black Macbook (running Mac OS X 10.4.11) has barely been connecting via wifi. It seems to be able to connect to private networks it's familiar with if it is literally within 5-10 feet of the router. Otherwise, it will connect at full strength for up to about 2 minutes, and then suddenly without any warning dips down to one bar, and then promptly disconnects completely, does not detect any networks. If I restart the computer it will go through the same pattern. Is this a hardware problem related to age? A software problem related to uninstalled updates? A virus? Thanks for your help.

Starting about 2 months ago, my 5-year-old black Macbook (running Mac OS X 10.4.11) has barely been connecting via wifi. It seems to be able to connect to private networks it's familiar with if it is literally within 5-10 feet of the router. Otherwise, it will connect at full strength for up to about 2 minutes, and then suddenly without any warning dips down to one bar, and then promptly disconnects completely, does not detect any networks. If I restart the computer it will go through the same pattern. Is this a hardware problem related to age? A software problem related to uninstalled updates? A virus? Thanks for your help.

Disconnect from Server

I have a G4(MDD)that I am trying to connect to my Windows 2003 Server. The problem is that when I connect using SBM,CIFS or AFP I get a [email protected] has been disconnected. I have changed patch cables added some info into the DNS nothing seems to help. I have another G4 (MDD) with the same setting running with no problems. Im not sure what more to try. Im thinking of telling my company to buy an Xserve that would solve the problem.
Thanks for the help.
The OS on the G4 is 10.4.6

Now I understand better some of what's going on. The networking functions are fine; it's the GUI that's misleading me.
As soon as I select a server icon in the "Shared" section of the Finder sidebar, Leopard connects as "Guest" and displays the share points. Select a share point and the shared volume icon mounts on the desktop, and the triangular unmount icon appears next to the share icon in the Finder.
BUT: disconnect from server or share point, and the Finder STILL displays all share points and indicates I am still "Connected as: Guest" . . . but now there is no disconnect triangle.
Further weirdness: If I have a share point mounted, and click "Connect as" (button available in column-view), it unmounts the share, but doesn't launch the "Connect to Server" dialog.
Then, click "Connect as" again to bring up the "Connect to Server" dialog, authenticate as NON-GUEST user to an SMB share, the volume mounts, but the Finder displays "Connected as Guest"!
Even if I connect as a NON-GUEST user to a PC share using SMB in the older way -- CMD-K or "Go > Connect to Server" -- then select the newly-mounted Server icon in the Finder sidebar, the Finder tells me I am -- you "guest" it -- "Connected as Guest."
Interestingly, the Finder displays AFP connections correctly, with actual user names, and a "disconnect" button, under the server icon in the 1st Finder column; SMB connections do not.
So my issues here seem to be confusion created by miscues in the GUI -- the "Connected as Guest" indication before you've actually connected, and after you've disconnected. And for SMB connections, the additional miscues of being told you're connected as guest instead of the user account you've authenticated under, and the curious absence of a "Disconnect" button under the server icon in the 1st Finder column.
I just installed Leopard three days ago. Overall, I love it. I hope this feedback helps Apple refine some minor bumps in the user experience.
Message was edited by: Samildanach

Delete emails from server after retrieving with IMAP protocol?

Hi,
I am using Mail as my email program and have set up my account with IMAP.
When I use the POP protocol, I get the option to 'Remove copy from server after retrieving message'. When I set up Mail with the IMAP protocol, there is no such an option. The result is that my server inbox is slowly filling up and I manually have to login on my server to delete older messages.
Is there a setting to automatically remove retrieved messages from my email server using IMAP?
Thanks for your help.
Erik

Dear Thomas,
Thanks for the clarification! Now I understand the mechanism.
Still I would like to know if there is a way to automatically remove retrieved messages from the e-mail server. Would it help to automatically move my incoming messages in INBOX to a different mailbox in Mail.app? How would I set this up?
Thanks for the response!
Erik

My new Mac Air continues to disconnect from WiFi after going to sleep. When waking it up I have to manually re-connect. How do I keep it connected?

My new Mac Air continues to disconnect from WiFi after going to sleep. When waking it up I have to manually re-connect. How do I keep it connected?

I had this problem too and solved it by doing a clean install. After that it was gone.
This is a drastic method since it takes quite some time to reinstall lion and all your software.
Thoughts I had why it started working after a clean install are the following:
It looked like the airport wasn't able to reconnect fast enough before the connection timed out. So what could have prevented my mac from being able to connect fast enough?
Apps that consume processor cycles. I love what I would call 'System Enhancers', little apps that enhance my workflow (Moom, Alfred, Dropbox, Default Folder etc). I'm not saying that these are the problem, they might be programmed processor friendly, but check if you have apps that consume processor cylcles. It might prevent airport from being able to reconnect quickly enough before it times out.
Mobile Config profiles. Another thought I had was that I had a mobile config 802.1X profile installed for the company were I worked. It used TTLS to connect to the corporate network. This profile might have gotten in the way.
And a sidenote...
Routers with hardware acceleration might also be a problem. My router is a Wireless Gigabit Router 300N WL-351 and has hardware acceleration. As soon as I activate that my wifi connection keeps dropping. It is as if a Macbook Air can't handle that amount of optimisation.
That's it, hope it helps those who are still having the problem.
Best, Jan

Why I get disconnected while calling after 3 minutes?

Why I get disconnected while calling after 3 minutes?

I wish I could put 1 more quarter and solve the problem. And yes, it happens in every call that goes beyond 3 minutes, local or international. To make it worst, I bought an iPhone 4 for my wife and has exactly the same issue, we are both from the Philippines. Thinking that they might be selling us over here the over runs or defective gadgets to my surprise my sister in law who lives in Texas is experiencing the same issue. I was looking in the apple store for support and found out that there is a batch of iphones that came out with that issue and that needs some kind of fix. The problem is that apple endoreses you to your network provider and here our network provider does not know what to do.. Have you heard of this fix? Kindly advice

[Solved] Screen goes blank after ten minutes

When I let my Asus EEEPC (1005HAB) idle on battery (especially if I'm watching something with VLC), after ten minutes the screen turns off. I can move the mouse or press a key to bring it back, but that gets to be annoying when I'm engrossed in a movie. I'm assuming this has something to do with a screensaver or power management setting. Correct?
I'm running Mate 1.8.1. The power management is set to put the display to sleep after 1 hour. And running pacman -Q mate-screensaver returns package not found. I have looked through the dconf settings, but haven't been able to find the correct setting to change (if its even in there).
Last edited by neon612 (2014-07-30 01:30:16)

xset -q:
Keyboard Control:
auto repeat: on key click percent: 0 LED mask: 00000000
XKB indicators:
00: Caps Lock: off 01: Num Lock: off 02: Scroll Lock: off
03: Compose: off 04: Kana: off 05: Sleep: off
06: Suspend: off 07: Mute: off 08: Misc: off
09: Mail: off 10: Charging: off 11: Shift Lock: off
12: Group 2: off 13: Mouse Keys: off
auto repeat delay: 500 repeat rate: 30
auto repeating keys: 00ffffffdffffbbf
fadfffefffedffff
9fffffffffffffff
fff7ffffffffffff
bell percent: 50 bell pitch: 400 bell duration: 100
Pointer Control:
acceleration: 2/1 threshold: 4
Screen Saver:
prefer blanking: yes allow exposures: yes
timeout: 600 cycle: 600
Colors:
default colormap: 0x22 BlackPixel: 0x0 WhitePixel: 0xffffff
Font Path:
/usr/share/fonts/misc/,/usr/share/fonts/TTF/,/usr/share/fonts/Type1/,built-ins
DPMS (Energy Star):
Standby: 7200 Suspend: 7200 Off: 14400
DPMS is Disabled

N95 - emails vanish when disconnect from server??

Hi,
I've set up my N95 to send and receive emails - its doing both even though when I "send" it says server not found but the email DID arrive at its destination..??
My other problem is that after I have downloaded emails to my phone and I then disconnect from the server - when I then goto reconnect those emails dissappear.. Is there a setting to stop this from happening?
can you help me with eithe rof those issues?
Thank you
Angela

Good luck with that. It most likely has something to do with the network, and Bridge is really not set up for network function. It works that way but Adobe says there are so many variables with networks that can not be quantified. Not sure but if Bridge does error checking like Photoshop does it could lead to what you see.

Some messages not deleted from server after downloading

We have about 1,000 mail users, all of whom use Apple's Mail app to retrieve their mail using POP. We've seen users' mailboxes on the server where not all messages have been deleted after downloading, even though the user's app has been configured to delete messages immediately after downloading. The strange thing is, undeleted messages appear in large non-contiguous blocks of time. Like there will be 100 messages from January, then 250 from July, and so forth.
Has anyone seen this behavior? Can anyone help me a) understand why this is happening and b) how to fix it? Thanks in advance to whoever can help.

Thanks- but I don't want the messages deleted when they are deleted from my Mac, I want them deleted when I download them. However, I just found the setting so I'm fine.
Thanks, again!
set delete from server when deleted from my mac in mail preferences
And if you want you could tell us a little more - like what type of account, what settings, etc

PC disconnects from VPN after several hours, can't reconnect until PC reboot.

Hi,
I started using a private VPN for video gaming in general since last month, but I've started running into a problem I cannot fix... my PC tends to disconnect from the VPN after a while (6~12 hours of use?) and I can't reconnect to any VPNs until I reboot my
PC.
However.. my normal internet connection seems to work fine.
When I try to reconnect to the VPN after I get dropped, I'm welcomed by this error:
http://puu.sh/bicqT/0a6f1f8537.png
I'm on Windows 7 64bit and I use the default windows VPN client... idk what's it called, it's what you setup in the network and sharing center.
I've tried the following things:
*restart network adapter
*diagnose the issue with windows 7 network diagnostics
*/flush DNS cache
*/release and /renew lease
*reset internet connection
*using a neighbor's internet connection and I'm still unable to connect to any VPN until PC reboot.
-- diagnosing the wireless adapter after the disconnect from VPN happens leads to this...
http://puu.sh/bibQs/9873c02068.png
http://puu.sh/bibn7/93ec6f0934.png
http://puu.sh/biboF/3c9f865f15.png
http://puu.sh/bibpw/b204c59f01.png
http://puu.sh/bibq9/a10d3246d1.png
I cannot repair it through diagnostics.
Anyway, it's a problem on my end because I share the VPN with 2 other friends and they don't experience this problem... >_<
If there's any information missing, please tell me and I'll provide.
Thank you for any help!

Hi,
could you tell me do you run more than one VPN connection on your PC?
Did you try to delete and re-configure the VPN?
What type of security software are you using? Any kind of software which might block the traffic or close the port in case it thinks that something fishy is going on?
Could you determine which manufacturer is your Wireless card, visit their website and download the latest drivers directly from their site. Or if you are using laptop, visit manufacturers website and download wireless drivers.
You can try to update the drivers manually.
What about that 'Enable logging' thingy? Can you enable it and when the next time disconnection happens, you might determine what is the exact issue with the VPN.
Please click on Propose As Answer or to mark this post as and helpful for other people. This posting is provided AS-IS with no warranties, and confers no rights.

PAD DISCONNECTS FROM WIFI AFTER A SHORT TIME HARD RESTART IS REQUIRED TO CONNECT AGAIN

MY IPAD NEEDS TO BE HARD RESTARTED EVERYTIME BEFORE I CAN ACCESS MY WI FI ANY IDEAS?

Franco Solerio wrote:
Since I updated to iOS 5.1 my iPad (1st gen) disconnects from WiFi network after 30 minutes. I did a full system restore with iOS 5.1 and the problem persists.
How to replicate:
Disable auto-lock
Connect to wifi network
Open an app that continuously does network activityYou might for example run a shoutcast webradio streaming app and start listening to some music
Leave the iPad running and turned on
After approx 30 minutes wifi drops and your music app stops the stream
This happens to me every time, after approximately 30 minutes, with either the iPad on USB charge or disconnected from charge.
Used to run apps connected to wifi regularly for hours and never had this problem before the upgrade to 5.1
I already tried to:
Restore network settings
Completely wipe and restore iPad to 5.1
Reboot wifi router
My router is a Netgear 834 G
try updating your router firmware http://support.netgear.com/app/products/family/a_id/1288

Clean way to disconnect from server?

I can't find any socket.disconnect() method (just a socket.isConnected()). What's the cleanest way to disconnect from a server? I just do a socket.close, but then i get this exception on the server:
java.net.SocketException: Connection reset
at java.net.SocketInputStream.read(Unknown Source)
at java.io.ObjectInputStream$PeekInputStream.read(Unknown Source)
at java.io.ObjectInputStream$PeekInputStream.readFully(Unknown Source)
at java.io.ObjectInputStream$BlockDataInputStream.readShort(Unknown Sour
ce)
at java.io.ObjectInputStream.readStreamHeader(Unknown Source)
at java.io.ObjectInputStream.<init>(Unknown Source)

You can send a bye message.
Once the server has that it knows that it can close the socket on its end (and it can safely ignore a reset error.)

Automator - Disconnect from server

Hi,
I'm working on a small automator workflow that helps me synchronizing iTunes music across 3 computers. Basically it connects to a server, uses the sync folders action to synchronize the contents and then I want to disconnect from the server.
That's the point where I'm stuck ... searched the web but couldn't find a real answer how to disconnect from a server using Automator.
Any ideas?
Thanks a lot!

I don't have an answer for you.
Did you ever get it working?
If so I would like to shamelessly steal your workflow.
thanks
chuck

WRT54G v6.0 Disconnects From Server After Ten Minutes

Similar Messages

Maybe you are looking for