WRT54G ver.6 wireless router will not connect either way

WRT5G ver.6 Router will not connect to the internet or other PCs wired nor wirelessly, PC shows "limited or No Connection".  The orange light is not on and will not come on when I press the Cisco System Light/Button on front.  I cannot access the router through the browser nor PING it through the command prompt.  I have tried to reset it and unplug it for few seconds, please, me OBIWAN, your my only hope.

I think your router is bricked, You can try the steps on this link and check if it solves your problem or not.

Similar Messages

  • HP Officejet Pro L7780 All-in-One Printer & Verizon D-Link wireless router. will not connect

    I have a HP Officejet Pro L7780 All-in-one and not able to get it to connect to my Wireless  Verizon D-Link Router.
    Please advise.
    aileensnider

    Let's start here.
    Printer does not maintain wireless connection.  
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02817031&tmp_task=solveCategory&cc=us&dlc=en&la...
    Say thanks by clicking the Kudos Thumbs Up to the right in the post.
    If my post resolved your problem, please mark it as an Accepted Solution ...
    I worked for HP but now I'm retired!

  • My wireless keyboard will not connect to the Mac mini. I am unable to login to change settings. How can I bypass login?

    my Mac mini is password protected and my wireless keyboard will not connect.

    Troubleshooting wireless mouse and keyboard issues
    OS X: Bluetooth devices become unresponsive

  • WRT54G Wireless Router Will Not Assign a Network Address

    A Linksys WRT54G router will not assign a network address when I access the router using a Linksys WPC600N wireless card. I have the same problem accessing the router with a TRENDnet TEW-621PC wireless adapter. Both wireless adapters are assigned network addresses when I use other wireless routers. Also, I have no problems being assigned a network address when I access the WRT54G router in question using an old 2WIRE 802.11b wireless card.
    I have tried "Repairing" the connection, I have used ipconfig to "release" and "renew" the connection. However, each attempt fails to have a DHCP address assigned.
    I am a visitor at the work location with the connection problem, the router works for others without any issues.
    Thanks

    Well in such case .... you can try few settings on the wireless adapter ....
    If you are using WLAN monitor .....
    Click start >> All programs >> Linksys wireless monitor >> Click on "Profile" >> Delete all profiles >> Click "New" >> Type in the wireless network name >> Click next >> Configure the rest of the wireless settings same as in the router ...
    At last point it shows .... all the configuration settings ...reconfirm that  >> Click on connect ot a network & reboot the computer ...
    After reboot see if it shows connected or not....
    You can also use Static Ip in the configuration ....

  • WRT300n wireless G will not connect.

    Any ideas. I gad a wrt54g and had no problems. I updated to the new wrt300n and my laptops will not connect.

    Follow this setting on N standard router ......
    Open routers set up page .....
    Click wireless .......
    1)  Radio Band - 40Mhz
    2)  Wide Channel - 6
    3)  Standard Channel - 9

  • PC shows network in wireless but will not connect

    I have an open connection and my mac works fine but the pc will not connect...what exactly do I need to do in order to get the pc to work?

    Hello Dan Miller...Welcome to the Apple Discussions!
    How are you connecting your AirPort Express Base Station (AX)? That is are you connecting it as a "wireless client" to an existing wireless network or as a stand-alone Internet router? That is, if it's an Internet router, you would be using it for both Internet access and for streaming iTunes.

  • RV180 router will not connect to ISP using PPPoE

    I had the same problem.  The RV180W would not connect to an AT&T DSL connection using PPPoE (modem in bridge mode), or behind the DSL Modem/router with the DSL modem/router providing a dynamic IP to the RV180W or a cable modem (TimeWarner Roadrunner dynamic IP).  I upgraded the firmware yesterday and now the RV180W will connect to a dynamic WAN IP, but it still will not connect using PPPoE.
    I have also noticed the admin interface is only accessible about 75% of the time.  When going to 192.168.1.1 the login prompts either don't come up or if they do, after logging in, the screen never fully loads after that.  I have to reboot the router to get it to work.
    Also, the router has not yet pulled DNS from either the DSL or the cable modem.  I had to manually enter those addresses.
    Any suggestions on the PPPoE issue?  Any thoughts as to why the admin interface is not always accessible or the DNS?
    Thank you,
    Ron

    Hi Ron, thanks for using our forum, my name is Johnnatan and I am part of the Small business Support community. About your login issue I recommend you to use different browsers such as Mozilla, i.e 9.0 or superior, Safari, Opera etc. About the PPPoE question, basically you just need the username and the password provided by your ISP. Can you please reach out to our Small Business Support Center and open a Service Request to address this issue? One of our Engineers may be able to work with you and diagnose the root cause. You can find the appropriate contact information for SBSC in the below link. http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
    I hope you find this answer useful,
    *Please mark the question as Answered or rate it so other users can benefit from it*
    Greetings,
    Johnnatan Rodriguez Miranda.
    Cisco Network Support Engineer.

  • Wireless Printer Will Not Connect To Any Machine

    Okay so just want to start out saying any help is appreciated, haven't used a forum before so hoping for any answers.
    I have a HP Photosmart 5510 All in One B111a printer
    Trying to connect to 2 laptops 1 Win7 64 bit - 1 Windows XP Professional SP2
    I have had the printer for around a month - Set it up on my Win7 laptop no problem, needed to connect to the Win XP laptop, and after turning it on it will not connect to either randomly
    It seems so far that the printer is connected to the network according to what it says, and both laptops install the software okay but when searching for the printer neither can find it, it then resorts to searching via IP where it still cannot find it.
    So far I have attempted to reset defaults on printer, reset network defaults on printer, change the IP address, update the IP address, reinstall the software, reinstall the driver, install the full feature installation package, the network diag tool, it cannot seem to find the printer at all even though on the printer screen it states it's connected to the network fine.
    It works fine through a cable and at one point i made a WPS connection via my Win7 laptop but couldn't really figure out what to do next and if it would help my situation so disconnected.
    I don't know whether this is down to some stupid mistake I've made/something basic I've missed (it's my first printer) or an actual problem
    Please help!

    What router?
    Download and run this utility: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-104282-2&cc=us&dlc=en&lc=en...
    What does it say?
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Wireless router will not recognize password

    My wirelss router will not recognize the password on the router. Would like to change it to something wowrkable.

    https://customer.comcast.com/help-and-support/Wireless-Gateway
    http://customer.comcast.com/help-and-support/internet/wireless-gateway-username-and-password/
    http://customer.comcast.com/help-and-support/internet/securing-wireless-gateway-network/
    http://customer.comcast.com/help-and-support/internet/broadband-gateways-userguides
    http://media2.comcast.net/anon.comcastonline2/support/userguides/Wireless_Gateway_User_Guide_030811....

  • Time capsule wireless router will not work

    I have a Time Capsule that I use as a wireless router in my condo.  Our internet company was recently purchased by another company, and after the transition, I am not able to connect to internet wirelessly.  My condo is wired with active ethernet ports.  If I plug the ethernet cable directly into my computer, I am able to log in to the ISP's main page and connect to the internet without any problems.  However, if I plug my ethernet cable into the Time Capsule as I did before, I cannot connect.  Before the company bought the old company, I didn't have any issues.  I've called their Tech Support 3 different times about this and they tell me they don't provide support for my wireless routers because there are so many different types.  They suggested resetting the router password, but I'm not completely sure how to do that.  Is that different than my airport password?
    I should also note, that if I pull up System Preferences and to the "assist me" feature under the Network option, it tells me that I'm connected. 
    Any help you can provide would be fantastic!  I'm at my wits end with this issue, as I connect a number of devices to my Time Capsule wirelessly.
    Regards,
    Jake

    I have a 2TB Timecapsule and really only use it for Time Machine backups. But the Wi-Fi side is used to sync my iPad at times.
    Mine is wiredup thus;
    Eth cable from iMac to modem (not the WAN port should you have one),  then eth cable from modem to T/Cap in the WAN port (bottom port with an O sign above it)
    I believe when its connected up you may have to set up a wireless network. Follow the instructions to set up Wi-Fi and Network
    and then give it a password. The WiFi icon should appear in the menu bar where you can switch it on or off.
    Its been sometime since I set it with the help of Apple Techs so I might be a bit rusty.
    Alan

  • Cannot log into blend and has said max attempts exceeded, Link will not connect either

    I downloaded the Blend software on my macbook pro and it would not log in with my Blackberry ID. After 5 attempts it locked me out.
    I reset my Blackberry ID and tried again, but it will not let me even attempt to login and says max attempts exceeded. I uninstalled and reinstalled and still the same problem. Also Link will not let me connect. Any ideas please? looks like I am going over to Iphone if this continues and bin my Z30.

    Jeff,
    Thanks for the info on policy settings.
    Let's see: I had 8.1.5 installed and I tried the update to 10g but only works from 8.1.7 or 9i, so then uninstalled and re-tried to do fresh install in a different home (OraHome10 vs OraHome8). That didn't go so well--it changed my 8i somehow so 8i would no longer work. Then I tried fresh install of 9i with a new starter DB--couldn't get into that DB. So uninstalled 9i, uninstalled 10g, uninstalled 8i, deleted every reference to Oracle on my computer, registry, etc., and re-tried 10g. I even went and bought a registry cleaning tool to zap things to make sure it was clean. It looked like it installed fine, provided me with starter DB but I just can't get into it. I'll let you know if the policy setting works.
    I'm trying to look on the bright-side and say that we are learning a lot!
    Dave

  • WRT54GX4 Router Will Not Connect to More Than One Computer at a Time Wireless

    I have a WRT54GX4 and cannot connect wirelessly with more than one laptop at a time.  Each laptop I have will connect if I disconnect the other one.  I have upgraded to 1.00.20 firmware and tried to find a setting for the router to address the problem without success.

    double check on the mac addresses that you have saved so that your wireless computers can connect properly to your netwok, or you could just disable the mac filtering so that all of your computers can easily connect, just secure your wireless network

  • WRT54G ver. 2 Does not Connect to Viera

    I was trying to use the ethernet ports on the back of my router to connect to my LAN port on the Panasonic Viera Cast system, but am not having any luck.
    I have confirmed that the internet works.  I was able to run a direct line from the modem to the Viera system and determine that the internet is working properly.  However, if I add the Linksys to the mix, the television acts like it doesn't receive the signal.  I really don't want to use a wireless adapter on my television.  Is there something I can do to either change the Linksys settings or get the Panasonic to recognize the signal from the router?

    And I also got to test if any of the other computers in the house were receiving wireless signals.  They were not, even though it began to work again when I moved it back to the original outlet.

  • Time capsule wireless router can not connect both Macbook and iPad

    Currently my new time capsule can only connect my macbook pro wirelessly or by ethernet. My iPad or PC can not been connected to it. I guess the setting for the router is something wrong, but I do not know how to fix it. The settings indicate that there is no DNS address, and the router is off (bridged). I tried to change the router setting, but does not succeed. Sincerely ask for help.

    The settings indicate that there is no DNS address, and the router is off (bridged). I tried to change the router setting, but does not succeed. Sincerely ask for help.
    Sorry but I need you to clarify.. router is off.. what router are you talking about??
    If the clients do not have DNS, have you tried just supplying the standard google dns ie... 8.8.8.8 (very lucky number for Chinese) or 8.8.4.4
    http://code.google.com/speed/public-dns/
    You can usually set dns manually whilst still using DHCP for IP address.
    But better to start again.. reset the TC..
    Give it a simple name .. no spaces.. all alphanumeric.. the default name is NOT windows networking valid.
    eg I name my TC.. TC1
    Wireless name.. same rules.. I use TC24 and TC5 (I use separate names for 2.4ghz and 5ghz as I do not want computers auto swapping bands) I also set channels manually.. again because I do not want them auto swapping channels.
    Wireless passwords.. same rules.. you need to make it a bit longer of course.. but pure alphanumeric no spaces.
    In the disk area, assuming you want disk access.. then put in the WORKGROUP name.. usually WORKGROUP.. in caps btw.
    If you do all that it will usually also work with iPad.

  • New N router will not connect to the internet

    I recently acquired the Actiontec MI424WR Rev. I router.  I'm upgrading from the MI424-WR Rev. D router.  I followed the instructions and all of the necessary lights come on except for the "internet" light.  It stays yellow and does not turn green.  I double-checked the connections.  The "power" light is a solid green.  The "wan coax" is a solid green.  I connect ethernet cables to the yellow ports and they show green.  Please let me know what I may be doing wrong in my setup.  Thanks.
    Solved!
    Go to Solution.

    How do I release my DHCP lease
    you might have missed this step.
    Also I don't think you have to return that router, so if you do not (read your packing slip it will tell you) then you might want to take this under advisement.  It's a really neat way to make that old router useful..
    Can I get an ethernet connection in a room with only coax?

Maybe you are looking for