Wrt54g version 2.2

I have an older router the wrt54g version 2.2. And I want to use this for testing. Now I try to configure the router. But the router won't get any internet access. I tried to configure by 192.168.1.1 and the cd. And no matter what I do I won't have any internet connectivity. I tried to do a firmware update but this was failed. So also that won't work. I'm not sure what I can do now, can you help me further
Message Edited by patricia8609 on 05-13-2009 09:15 AM

Reset your router and then re-configure it...
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Also make sure that your computer is set to obtain IP automatically, disable any firewalls, security softwares on the computer before trying to access the setup page...
To configure your Linksys router
Follow this link if your Internet Service Providor is Cable
Follow this link if your Internet Service Providor is DSL

Similar Messages

NAT issue - WRT54G Version 1.1 with Vista Home Premium

Router = WRT54G Version 1.1
I am trying to figure out the cause of my problems, this router or Vista?
I have 2 PC’s (just want to use my Vista 1) connected to the same router that is connected to a cable modem – the Windows XP machine has no problems bar its age and spec. I have a brand new PC with Vista Home Premium installed on it, now it is this new PC that I am having NAT problems with and port blocking.
I have installed Windows Live Messenger and when setting it up I went into Tools/Options/Connections and I get an error message:- "You are connected to the internet through a UPnP port restricted NAT. The Windows Firewall is enabled. (User)"
I have no option to run the trouble shooter (greyed out)…….
If I turn off Windows Vista Firewall I get:- "You are connected to the internet through a UPnP port restricted NAT. (User)”
Since this I have installed Media server software and have to reset the port it uses every time as it is always stating that it is blocked.
I have downloaded OpenOffice via a torrent client which also stated that I had NAT problems.
I have no NAT issues at all on my older XP PC and as a result I believe it is safe to rule out my router and modem……..I have only disabled Windows Firewall and this had made no difference, but I have not tried uninstalling it (no idea if that would make a difference)
Oh, I do not have UPnP enabled (router setting) – does this matter (I have tried turning it on but made no difference to this issue so I turned it off again)?
Message Edited by jomuir on 08-23-2007 02:50 AM

user11241256 wrote:
Documentation states that Oracle is supported on Vista business and Ultra. unfortuntatly Ihave Home Premium 64 and was curious if anyone had experience imstalling on this OS. I did attempt to install the 11g and I got one warning below that I could not find in the documentation for errors. You have answered your query yourself.
You might be able to get the things running on an unsupported combination but there is no guarantee about the stability.

WRT54G Version 7.0 - mother of all problems: Why are the DNS-fields in the status blank?

Ever since the purchase of my WRT54G Version 7.0 WLAN Router two years, I kept getting IP- and DNS-problems, but recently, I cannot access websites anymore at all. As I've already replaced the thing with another router months ago and just now, started to set it up at a friend's place while getting the same problems (with every single computer in the network), I'm sure that the problem lies at the router. All Windows computers report in uni sono that there may be a DNS problem. Firmware is up to date to 7.00.4. Ironically, LinkSys doesn't seem to feature drivers downloads to Version 7.0 anymore, though.
I've got the DHCP-server function activated, left the IP-address to 192.168.1.1 and the DNS-addresses 1, 2 and 3 to the usual 0.0.0.0. I didn't change the default WINS 0.0.0.0, either.
Interestingly, however, when switching to the status tab, the DNS1, DNS2 and DNS3-fields remain completely blank. Therefore, I assume that the router doesn't run any DNS with 0.0.0.0-setup.
Now, how can I make this expensive thing take up the DNS-tasks so that all those computers can access websites again?

Who is your Internet Service Provider ?
What is the IP Address you are getting on the status page of the router ?
What is the IP Address you are getting when connected to the modem directly ?
You can Download the firmware for WRT54G V7 (7.00.8)
Try this :
Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

Wireless Router WRT54G version 7. Connected computer gets disconnected from internet

I have recently installed a Wireless Router WRT54G version 7 for my home office purpose.
My home PC and my laptop are connected to it. Especially on my laptop, I have observed frequently getting disconnected from the internet. I need to power OFF the router and power it ON to get the internet connection restored
Need help to get this problem resolved
Thanks
Rohit

Access set up pageof router .... look for MTU ....change the size from 1500 to 1300 ....click save settings ....
Click on wireless tab ....change the channel to 11 .....click save settings ....
Go to advance wireless settings subtab ....
Beacon interval 75
RTS & Fragmentation threshold 2306...... click save settings ...
Click on status check Ip address & firmware version on the same & let me know ...

Linksys WRT54GS Version 6 router help

Hi all! I have a Linksys WRT54GS Version 6 router with Firmware Version: v1.50.6 and I was wondering if anyone could help me find a free log viewer, since the log viewer that comes with the router just gives the last few sites outgoing and incoming, and it doesn't time it either. Anything that will work with my router that will record all day info as well as put the time? I'd also like it (if possible) if it could identify which websites those IP's belong to; sometimes I will put an IP in the address bar and nothing happens or I get an error.
Also, I can't seem to be able to telnet into my router. I put the right IP 192.168.1.1 8080 which is the port that shows under Administration/Management "management port:" 8080. When I telnet (I'm using vista and I installed the telnet client and server) it says connecting and then just sits there for a long time and then asks me to push any key and says connection timed out. I also tried with port 80 and 23, nothing.
Thanks!

*BUMP*
I gathered from what I read on the 'net that this particular router pretty much sucks in terms of putting 3rd party firmware, of telnetting into it, etc. So, is it basically true that there is no way to telnet into this? Also, no one knows of any monitoring or log viewer that works with this version?? Please?
Message Edited by PsychGirl on 04-16-2009 09:35 AM

Why there is no option for WRT54G Version 7??? the versin...

Why there is no option for WRT54G Version 7??? the versin no. jump from 6 to 8??Which firm ware should I download?

For US no vesrion 7 is released. Might be in other countries.

WRT54G version 3.0 Streaming Video Issue

I have a WRT54G v3.0 wireless router that constantly drops connection when I try to stream video from the internet. If I eliminate the router and connect my laptop or desktop directly to my cable modem streaming video works perfect. Once I put the wireless router back into play and try to stream video I lose connection to the router. Normal internet use (e-mail, sports sites, etc.) work fine but as soon as I go to a site like youtube or espn and try to stream video the wireless connection drops. I have read numerous message boards that talk about firmware upgrades that will fix the problem but all of the message boards talk about WRT54G versions other than mine. Can anyone out there tell me why my WRT54G v3.0 router constantly drops connection when streaming video as well as tell me how to fix it?
By the way I currently have firmware version 3.03.6 (Jan 6, 2005) installed

I think the latest for v3 is firmware 4.21.1. Check out your model and version on http://www.linksys.com/download
The box said windows xp or better... So I installed Linux!

WRT54G Version 3.1 Connection Issues - Help Please

Good Morning,
We have a WRT54G Version 3.1. Our existing network is wired and functions fine, I am adding the WRT54G for a few wireless clients.
During testing I have connected the wireless to my computer via CAT5 cable to port 1. I have connected another CAT5 cable to the internet port of the router from a known good wall jack.
When I first open the default address 192.168.1.1 and enter the password, all seems well. Due to having servers that hand out IP addresses, I disable the routers DHCP capability.
I enter the following information for example:
Local IP: 81.0.0.90
Gateway: 81.0.0.1
Subnet: 255.255.255.0
DHCP disabled
etc.
After changing the the local IP and receiving a confirmation that my changes were saved and I will be going back to the previous page, the page won't display with the address changed to 81.0.0.90 and it is blank.
I release my IP address through cmd, clear my dns cache and reboot the computer. After restart, I am presented with the stock MS address of 169.254.X.X.
I cannot connect to the local IP I established at 81.0.0.90 and nothing appears to work. The only thing I can do is reset the router and start from scratch...again.
Any ideas on what keeps happening and how it can be resolved once and for all?
Thanks in advance
Message Edited by T1Tech on 10-23-200603:49 PM

even if you have two DHCP enabled on both routers in your network, you will not get an IP adress conflict (exception of course if you're cascading two wireless routers).
a LAN port (ethernet router) to WAN port (wireless router) connection can be established allowing you to have both DHCP server enabled on your routers.
by doing the LAN to WAN connection, you will have two networks in a network.. both network won't meet cuz they will have different IP adress... router 1: could be 81.0.0.90, then router 2 could be 81.0.0.91.
if you want your two routers to meet and be in the network together, you just need to follow QUAK's suggestion to assign a static IP adress on your PC. or better yet, you can just connect the router you're disabling the DHCP server with to it's LAN port from a LAN port as well of your DHCP server (router 1). this is a LAN to LAN connection... by doing that, you will be able to open up the interface of your router 2(DHCP disabled) since your PC connected to it will get an IP adress...
"a helping hand in a community makes the world a universe"

Linksys Wireless Router: WRT54G Version: 2

I was just curious, since I have been talking to someone about the Linksys Routers and they were saying that WRT54G Versions 3, 4 & 5, all work successfully. Then when I asked him about Version 2, he said that he THINKS that the router will work.
Can someone please give me an answer: Will the Linksys Wireless Router: WRT54G Version: 2 work with a MacBook Pro?!

I get from 3 to 6 Mbps wireless and wired, which is considerably slower than my other Windows-based desktop and notebook over my 30 Mbps cable connection. My Dell notebook and desktop consistently get 15 Mbps wireless and 22 to 28 Mbps wired. Mac OS is relatively new to me, so I haven't had a chance to read as much I need to about optimizing connection speeds. But, I can either fix it by optimizing it, or perhaps Apple will come out with a firmware update since some people have been complaining about slow connections speeds and dropping connections.
In my work, I have several computers going at the same time, and for typical Web surfing, I see no difference in speed between the 6 Mps on the Mac and the 15 Mpbs on the Dell---it's really limited anyway by the Web site server. I do notice a difference in download times, but even for very large files, the difference is noticeable but not a problem. And, there has never been a problem streaming video or downloading trailers, etc.
Of course, only five years ago, my cable connection was first 128 Kbps (which was high speed then), then they jumped it up 1 Mpbs, then 10 Mbps, and now 30 Mbps---so the 6 Mbps on the Mac still seems pretty fast to me.
Speed will always be slower over the wireless compared to your Ethernet connection, but once you get speeds in excess of 1 Mbps, you only see the difference in download times, surfing is the same.
MacBook, MacBook Pro, Mac Mini PPC Mac OS X (10.4.7) Dell D500 and GX620 with Windows XP Pro

Newest firmware for WRT54G version 5.1??

I am a newbee, so please help.
When I download the firmware from this site it says the newest is 1.01.1??
But when I want to forward a port it says firmware prior to 1.32 won't work.
What new firmwire do I need and where can I download it?
By the way, will it also work on a WRT54G version 5.0??
Best regards Xaykev

hi , the firmware version 1.01.1 , will work with both the wrt54g v5 and the wrt54g v5.1
try this and then go ahead with the port forwarding.

WRT54G Version 2 Firmware Reset?

Hello,
I have a Linksys WRT54G Version 2 that I installed the V.6. firmware on, and now I cannot connect through the router, or even reach the admin panel. Is there a way to reset Version 2 like Version 5?
Thanks!Message Edited by Kadratis on 11-25-200612:49 PM

you can try to reset this router for 1 min. and Then try to upgrade the router firmware with v2 firmware. Go to site: ftp://ftp.linksys.com/pub/network and search for tftp.exe and download tftp.exe and use this tool to upgrade the firmware file to this router. May this help you!
Make sure you upload only v2 files.

Linksys Violation Error 0040756D for my Linksys WRT54G Version 3

We are using the Linksys WRT54G, version 3, wireless router and the 2,4 GHz Wireless-G PCI adapter. Whenever we boot the computer up we get a Linksys access violation error 0040756D that is pointing to a problem wth the WRT54G. How do I eleminate this issue?

This might be the Error message when you must have configured your linksys router with the Setup disk...So i think you need to uninstall the Linksys software from your Computer and this will solve the problem,,,
Click on Start - Control Pannel - Add Remove Programs and in the List you will find "Linksys Easylink Advisor" select and click on Remove. Once the software is uninstalled from your Computer Reboot your computer and i think this will eleminate the error message.

WRT54GS Version 5 Firmware Upgrade

I am confused as to how to update the firmware on my WRT54GS Version 5 Linksys router.
I went to the support section on here, but there are five different options of router firmware upgrade. I bought this a year ago and figure it needs the update, can someone help me?
The choices I found on here are:
    Upgrading the Linksys VPN Router's Firmware
     Upgrading the Linksys Wireless-G Access Point's Firmware
     Upgrading the Linksys Wireless-G VPN Router Firmware
     Upgrading the Linksys Router
     Upgrading the Linksys VOIP Router's Firmware
Which one would I want for this basic network router? The reason I ask is because my wireless Internet is constantly down. It won't work unless I do a hard reset of the router each time. It is annoying that I have to do this all of the time. I have never had this problem in the year I had it until six weeks ago. I have to reset it numerous times to get it to read the Internet and then go into the settings and rename it each time. Also, the router and my PC and my landlords laptop always connect through to the router fine, it is just the Internet causing problems.

Hi… you can use choice no. 4 which you’ve mentioned, enter the model number >> WRT54GS >> select version 5 and save .bin firmware file on computer and upgrade it according steps…

Wireless G model WRT54G VERSION 8

I have Wireless G model WRT54G VERSION 8 and I was wondering is there anyway for me to turn off the wireless part cause I have no use for it right now. I just want to use the wired connections ports to connect my computer and my xbox360.

User's manual, page 9, wireless network mode.

WRT54G Versions 5/6 with VoIP

Been using a Linksys WRT54G version 5 for sometime but just started using it to transport VoIP (ATA is Linksys PAP2). Unfortunately, every 3-4 minutes especially if on the phone, I will lose wireless and wired internet connectivity (and obviously my phone call). During this time the router's power light blinks for 5-10 seconds, then it recovers and everything works fine. I followed all the tech support suggestions and was already running the latest firmware (v1.09) for this device and still it always does this reset thing. I've reflashed, reset, etc.. several times with the same result. Finally Linksys said I could send it in under warranty coverage.
So I could get back up and running quickly I went to the store and bought a new WRT54G, which is a version 6 of the router. I was shocked to find out it was not an issue with the hardware, as this router (also loaded with v1.09 firmware) has the same problem. I happened to have an old Microsoft MN-500 wireless router in the closet and plugged that in, and it's been up and solid since. I guess unless anyone has any suggestions, I just wanted to let Linksys and everyone else know (as their tech support people don't seem to be able to pass message up the chain) that there is a problem with V1.09 and VoIP. The router seems to be overwhelmed by the VoIP traffic or something and just continously cycles.

I've only had this router for 7 days. I can just take it back to Office Depot and try another router or even another manufacturer.
I'm also having DHCP problems with this thing out the wazoo, so I'm about at the point of saying to hell with it with this router.

Wrt54g version 2.2

Similar Messages

Maybe you are looking for